Merge series from Shengjiu Wang <shengjiu.wang@nxp.com>:
Support PDM format and DSD format.
Add new dts property to configure dataline. The SAI has multiple
successive FIFO registers, but in some use
case the required dataline/FIFOs are not successive.
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
After a set of SOF-specific changes, this patchset correct problematic
uses of pm_runtime_get_sync() in ASoC, or simplifies the flow with no
functional changes. Two patches for Intel platforms also add a test on
resume success.
Additional changes were initially suggested to completely remove the
use of pm_runtime_get_sync(). These changes were dropped since they
are way too invasive, specifically in cases where the return values
were not tested, which would lead to duplicate pm_runtime_put(). The
remaining uses of pm_runtime_get_sync() cannot really be blindly
modified without context and knowledge of each driver.
There is no particular need to restrict building of S3C I2S driver to
supported platforms within the C unit, because Kconfig does it.
Removing such restricting #ifdef from s3c-i2s-v2 allows compile testing
it on other platforms.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220627143412.477226-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Daniel Mack <daniel@zonque.org>:
This is a series of some patches that I collected while using the
max98396 driver is a TDM mode setup.
They correct BSEL and PCM mode configs, add support for power supplies
and add some bits to the documentation.
The code is tested in TDM-16 and TDM-8 mode with 32 channel width.
Merge series from Samuel Holland <samuel@sholland.org>:
This series adds support for enabling the codec's internal microphone
bias, which is needed on at least some versions of the PinePhone.
Changes in v2:
- Move register update from component probe to device probe
Arnaud Ferraris (2):
ASoC: dt-bindings: sun50i-codec: Add binding for internal bias
ASoC: sun50i-codec-analog: Add support for internal bias
Samuel Holland (1):
arm64: dts: allwinner: pinephone: Enable internal HMIC bias
.../bindings/sound/allwinner,sun50i-a64-codec-analog.yaml | 5 +++++
.../arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts | 4 ++++
.../arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts | 4 ++++
sound/soc/sunxi/sun50i-codec-analog.c | 8 ++++++++
4 files changed, 21 insertions(+)
--
2.35.1
The conversion of the set_fmt callback to direct clock specification
included a small typo, correct the affected code.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220627094335.3051210-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SAI has multiple successive FIFO registers, but in some use
case the required dataline/FIFOs are not successive, so need
get such information from dts property "fsl,dataline"
fsl,dataline has 3 values for each configuration:
first one means the type: I2S(1) or DSD(2),
second one is dataline mask for 'rx',
third one is dataline mask for 'tx'.
Also set dma peripheral address and TRCE bits according to data lane.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Link: https://lore.kernel.org/r/1655451877-16382-8-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The resource info need to be accessed by hw_params()
function for multi fifo case, the start address may
be not the FIFO0. So move it to be a member of
struct fsl_sai.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1655451877-16382-6-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With DSD format, the pinctrl is different compare with
I2S format, because one dataline only has one channel
data, and the codec always mux the LRCLK pin to DSD
data line, and on i.MX8MQ the BCLK pin can route to
codec on DSD case for the MCLK is too high.
Add pinctrl operation that the pinctrl can be switched
on runtime according to the I2S format or DSD format
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1655451877-16382-5-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for more sample rates, because PDM format
bitstream has higher sample rates. for example DSD512
format, the bit clock is 22.5792MHz, if the word width
is U8_LE, then the max sample rate is 2822400.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1655451877-16382-4-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to properly bias headset microphones, there should be a pull-up
resistor between pins HBIAS and MIC2P. This can be an external resistor,
but the codec also provides an internal 2.2K resistor which is enabled
by a register.
This patch enables or disables the internal bias resistor based on a
device tree property.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
[Samuel: split binding and implementation; move to device probe]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220621035452.60272-3-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The use of pm_runtime_get_sync() is buggy with no use of put_noidle on
error.
Use pm_runtime_resume_and_get() instead.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The use of pm_runtime_get_sync() is buggy with no use of put_noidle() on
error.
Use pm_runtime_resume_and_get() instead.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
simplify the flow. No functionality change, except that on -EACCESS
the reference count will be decreased.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
simplify the flow. No functionality change, except that on -EACCESS
the reference count will be decreased.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
simplify the flow. No functionality change, except that on -EACCESS
the reference count will be decreased.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code does not check for errors and does not release the
reference on errors.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code does not check for errors and does not release the
reference on errors.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow the selection of the TDM slot that is used to send back speaker
monitor data. The DT property adi,spkfb-slot-no can be used to configure
this setting which defaults to 2.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-8-daniel@zonque.org
Signed-off-by: Mark Brown <broonie@kernel.org>
max98396_dai_set_fmt() modifes register 2041 and touches bits in the mask
0x3a. Make sure to use the right mask for that operation.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-7-daniel@zonque.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The device has up to 5 potentially independent power supplies:
AVDD, DVDD, DVVDIO, VBAT and PVDD. The former 3 are mandatory for the
device to function. One of VBAT and PVDD should also be made available.
Regulators are enabled during probe time and will stay active except when in
suspend mode.
Futher, the chip needs to be informed about the presence of VBAT through a
bit in register 0x20a0.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-5-daniel@zonque.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The example in audio-graph-card2.c has multiple nodes with the same name
in it. Change the port numbers to get different names.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220624092601.2445224-1-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Put the SGTL5000 in a silent/safe state on shutdown/remove, this is
required since the SGTL5000 produces a constant noise on its output
after it is configured and its clock is removed. Without this change
this is happening every time the module is unbound/removed or from
reboot till the clock is enabled again.
The issue was experienced on both a Toradex Colibri/Apalis iMX6, but can
be easily reproduced everywhere just playing something on the codec and
after that removing/unbinding the driver.
Fixes: 9b34e6cc3b ("ASoC: Add Freescale SGTL5000 codec support")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20220624101301.441314-1-francesco.dolcini@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
madera_adsp_rate_put always returns zero regardless of if the control
value was updated. This results in missing notifications to user-space
of the control change. Update the handling to return 1 when the
value is changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-5-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
madera_out1_demux_put returns the value of
snd_soc_dapm_mux_update_power, which returns a 1 if a path was found for
the kcontrol. This is obviously different to the expected return a 1 if
the control was updated value. This results in spurious notifications to
user-space. Update the handling to only return a 1 when the value is
changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cs47l15_in1_adc_put always returns zero regardless of if the control
value was updated. This results in missing notifications to user-space
of the control change. Update the handling to return 1 when the value is
changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The mixer controls for ASP TX3/4 are set to values that are not included
in their enumeration control. This will cause spurious event
notifications when the controls are first changed, as the register value
changes whilst the actual visible enumeration value does not. Use the
register patch to set them to a known value, zero, which equates to zero
fill, thereby avoiding the spurious notifications.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DAPM keeps a copy of the current value of mux/demux controls,
however this value is only initialised in the case of autodisable
controls. This leads to false notification events when first
modifying a DAPM kcontrol that has a non-zero default.
Autodisable controls are left as they are, since they already
initialise the value, and there would be more work required to
support autodisable muxes where the first option isn't disabled
and/or that isn't the default.
Technically this issue could affect mixer/switch elements as well,
although not on any of the devices I am currently running. There
is also a little more work to do to address the issue there due to
that side supporting stereo controls, so that has not been tackled
in this patch.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The initial settings will be written before the codec probe function.
But, the rt711->component doesn't be assigned yet.
If IO error happened during initial settings operations, it will cause the kernel panic.
This patch changed component->dev to slave->dev to fix this issue.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20220621090719.30558-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We discoverd that the state of BCLK on, LRCLK off and SD_MODE on
may cause the speaker melting issue. Removing LRCLK while BCLK
is present can cause unexpected output behavior including a large
DC output voltage as described in the Max98357a datasheet.
In order to:
1. prevent BCLK from turning on by other component.
2. keep BCLK and LRCLK being present at the same time
This patch switches BCLK to GPIO func before LRCLK output, and
configures BCLK func back during LRCLK is output.
Without this fix, BCLK is turned on 11 ms earlier than LRCK by the
da7219.
With this fix, BCLK is turned on only 0.4 ms earlier than LRCK by
the rockchip codec.
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Link: https://lore.kernel.org/r/20220615045643.3137287-1-judyhsiao@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The IMR was assumed to be preserved when suspending to S4 and S5
states, but community reports invalidate that assumption, the hardware
seems to be powered off and the IMR memory content cleared.
Make sure regular boot with firmware download is used for S4 and S5.
BugLink: https://github.com/thesofproject/sof/issues/5892
Fixes: 5fb5f51185 ("ASoC: SOF: Intel: hda-loader: add IMR restore support")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220616201818.130802-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently don't have a means to differentiate between S3, S4 and
S5. Add definitions so that we have select different code paths
depending on the target state in follow-up patches.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220616201818.130802-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The existing code only deals with S0 and S3, let's start adding S1 and S2.
No functional change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220616201818.130802-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 288fad2f71 ("ASoC: SOF: Intel: hda: add quirks for HDAudio DMA position information")
modified the PCM path only, but left the compressed data patch using an
obsolete option.
Move the functionality in a helper that can be called for both PCM and
compressed data.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Fixes: 288fad2f71 ("ASoC: SOF: Intel: hda: add quirks for HDAudio DMA position information")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220616201953.130876-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This should return PTR_ERR() instead of IS_ERR().
Fixes: e0100bfd38 ("ASoC: SOF: mediatek: Add mt8186 ipc support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/YqmWIK8sTj578OJP@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
The "wlf,spkvdd-ena" GPIO needed by the bytcr_wm5102 driver
is made available through a gpio-lookup table.
This gpio-lookup table is registered by drivers/mfd/arizona-spi.c, which
may get probed after the bytcr_wm5102 driver.
If the gpio-lookup table has not registered yet then the gpiod_get()
will return -ENOENT. Treat -ENOENT as -EPROBE_DEFER to still keep
things working in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220612155652.107310-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently wcd938x_*_put() unconditionally report that the value of the
control changed, resulting in spurious events being generated. Return 0 in
that case instead as we should. There is still an issue in the compander
control which is a bit more complex.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220603122526.3914942-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
