Writes and returns sampled data back to userspace.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During test of the w1-gpio driver i found that in "w1.c:679
w1_slave_found()" the device id is converted to little-endian with
"cpu_to_le64()", but its not converted back to cpu format in "w1_io.c:293
w1_reset_select_slave()".
Based on a patch created by Andreas Hummel.
[akpm@linux-foundation.org: remove unneeded cast]
Reported-by: Andreas Hummel <andi_hummel@gmx.de>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export the w1_read_8 function for use of drivers. The OMAP HDQ
driver(drivers/w1/masters/omap_hdq.c) uses this function.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
w1_reset_bus, added some comments about the timing and switched to msleep
for the later delay. I don't have the hardware to test the sleep after
reset change. The one wire doesn't have a timing requirement between
commands so it is fine. I do have the USB hardware and it would be in big
trouble with 10ms interrupt transfers to find that the reset completed.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a strong pullup option to the w1 system. This supplies extra power
for parasite powered devices. There is a w1_master_pullup sysfs entry and
enable_pullup module parameter to enable or disable the strong pullup.
The one wire bus requires at a minimum one wire and ground. The common
wire is used for sending and receiving data as well as supplying power to
devices that are parasite powered of which temperature sensors can be one
example. The bus must be idle and left high while a temperature
conversion is in progress, in addition the normal pullup resister on
larger networks or even higher temperatures might not supply enough power.
The pullup resister can't provide too much pullup current, because
devices need to pull the bus down to write a value. This enables the
strong pullup for supported hardware, which can supply more current when
requested. Unsupported hardware will just delay with the bus high.
The hardware USB 2490 one wire bus master has a bit on some commands which
will enable the strong pullup as soon as the command finishes executing.
To use strong pullup, call the new w1_next_pullup function to register the
duration. The next write command will call set_pullup before sending the
data, and reset the duration to zero once it returns.
Switched from simple_strtol to strict_strtol.
Signed-off-by: David Fries <david@fries.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
w1_control_thread was removed which would wake up every second and process
newly registered family codes and complete some final cleanup for a
removed master. Those routines were moved to the threads that were
previously requesting those operations. A new function
w1_reconnect_slaves takes care of reconnecting existing slave devices when
a new family code is registered or removed. The removal case was missing
and would cause a deadlock waiting for the family code reference count to
decrease, which will now happen. A problem with registering a family code
was fixed. A slave device would be unattached if it wasn't yet claimed,
then attached at the end of the list, two unclaimed slaves would cause an
infinite loop.
The struct w1_bus_master.search now takes a pointer to the struct
w1_master device to avoid searching for it, which would have caused a
lock ordering deadlock with the removal of w1_control_thread.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch contains the following possible cleanups:
- the following file did't #include the header with the prototypes for
it's global functions:
- w1_int.c
- #if 0 the following unused global function:
- w1_family.c: w1_family_get()
- make the following needlessly global functions static:
- w1_family.c: __w1_family_put()
- w1_io.c: w1_delay()
- w1_io.c: w1_touch_bit()
- w1_io.c: w1_read_8()
- remove the following unused EXPORT_SYMBOL's:
- w1_family.c: w1_family_put
- w1_family.c: w1_family_registered
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are three types of messages between w1 core and userspace:
1. Events. They are generated each time new master or slave device found
either due to automatic or requested search.
2. Userspace commands. Includes read/write and search/alarm search comamnds.
3. Replies to userspace commands.
From: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the following cleanups:
- make needlessly global code static
- declarations for global code belong into header files
- w1.c: #if 0 the unused struct w1_slave_device
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sending either a skip rom or a rom match.
Patch from Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds the triplet w1 master method and changes w1_search() to use it.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- white space changes.
- list_for_each_entry/list_for_each_entry_safe and reverse changes.
- small coding style changes.
- removed redundant NULL checks.
- use attribute group and macros instead of direct device attributes.
Patch is havily based on work from Adrian Bunk and Dmitry Torokhov,
thanks guys.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
