On Mon, Mar 25, 2013 at 06:26:50PM +0100, Ronald wrote:
> In reply to [1]: I have the same issue. Git bisect took 50+ rebuilds xD
>
> Smartd does not work anymore since 84a9a8cd9 ([libata] Set proper SK
> when CK_COND is set.).
> [1] http://www.spinics.net/lists/linux-ide/msg45268.html
It seems that the SAM_STAT_CHECK_CONDITION is not cleared
causing -EIO, because that patch modified sensebuf and
the check for clearing SAM_STAT_CHECK_CONDITION is no longer valid.
Fix that.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When the user application sends a ATA_12 or ATA_16 PASSTHROUGH
scsi command, put the task file register in the sense data with the
proper Sense Key. Instead of NO SENSE, set RECOVERED, as
specified in [SAT2]12.2.5 Table 92.
Tested:
Using udev ata_id to generate a passthrough command, IDENTIFY:
before:
sd 0:0:0:0: [sda] CDB: ATA command pass through(12)/Blank: \
a1 08 2e 00 01 00 00 00 00 ec 00 00
sd 0:0:0:0: [sda] Sense Key : No Sense [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 00 00 00 00 00 00 0e 09 0c 00 00 00 00 00 3f
00 18 00 a6 e0 50
after
sd 0:0:0:0: [sda] CDB: ATA command pass through(12)/Blank: \
a1 08 2e 00 01 00 00 00 00 ec 00 00
sd 0:0:0:0: [sda] Sense Key : Recovered Error [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 01 00 1d 00 00 00 0e 09 0c 00 00 00 01 00 00
00 00 00 00 00 50
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ODD can be enabled for ZPODD if the following three conditions are
satisfied:
1 The ODD supports device attention;
2 The platform can runtime power off the ODD through ACPI;
3 The ODD is either slot type or drawer type.
For such ODDs, zpodd_init is called and a new structure is allocated for
it to store ZPODD related stuffs.
And the zpodd_dev_enabled function is used to test if ZPODD is currently
enabled for this ODD.
A new config CONFIG_SATA_ZPODD is added to selectively build ZPODD code.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement support for WRITE SAME(10) and WRITE SAME(16) in the SCSI disk
driver.
- We set the default maximum to 0xFFFF because there are several
devices out there that only support two-byte block counts even with
WRITE SAME(16). We only enable transfers bigger than 0xFFFF if the
device explicitly reports MAXIMUM WRITE SAME LENGTH in the BLOCK
LIMITS VPD.
- max_write_same_blocks can be overriden per-device basis in sysfs.
- The UNMAP discovery heuristics remain unchanged but the discard
limits are tweaked to match the "real" WRITE SAME commands.
- In the error handling logic we now distinguish between WRITE SAME
with and without UNMAP set.
The discovery process heuristics are:
- If the device reports a SCSI level of SPC-3 or greater we'll issue
READ SUPPORTED OPERATION CODES to find out whether WRITE SAME(16) is
supported. If that's the case we will use it.
- If the device supports the block limits VPD and reports a MAXIMUM
WRITE SAME LENGTH bigger than 0xFFFF we will use WRITE SAME(16).
- Otherwise we will use WRITE SAME(10) unless the target LBA is beyond
0xFFFFFFFF or the block count exceeds 0xFFFF.
- no_write_same is set for ATA, FireWire and USB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The REPORT SUPPORTED OPERATION CODES command can be used to query
whether a given opcode is supported by a device. Add a helper function
that allows us to look up commands.
We only issue RSOC if the device reports compliance with SPC-3 or
later. But to err on the side of caution we disable the command for ATA,
FireWire and USB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The cache_type file in sysfs lets users configure the disk cache in
write-through or write-back modes. However, ata disks do not support
writing to the file because they do not implement the MODE SELECT
command.
This patch adds a translation from MODE SELECT (for the caching page
only) to the ATA SET FEATURES command. The set of changeable parameters
answered by MODE SENSE is also adjusted accordingly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since the next patch will introduce support for MODE SELECT, it
makes sense to start advertising which bits are actually changeable.
For now, the answer is none.
Default parameters can also be reported, they are simply the same
as the current parameters.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some other unlikely() should probably be removed as well. A fresh look
reveals an over-enthusiasm for unlikely() in libata-scsi.c.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ATA port may support runtime D3Cold state, for example, Zero-power ODD case.
This patch adds wakeup notifier and enable/disable run_wake during
supend/resume.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This changes the ordering of initialization and probing events from:
1/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
2/ allocate ata_port and schedule port probe in DISCE_PROBE
...to:
1/ allocate ata_port in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
2/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
3/ schedule port probe in DISCE_PROBE
This ordering prevents PHYE_SIGNAL_LOSS_EVENTS from sneaking in to
destrory ata devices before they have been fully initialized:
BUG: unable to handle kernel paging request at 0000000000003b10
IP: [<ffffffffa0053d7e>] sas_ata_end_eh+0x12/0x5e [libsas]
...
[<ffffffffa004d1af>] sas_unregister_common_dev+0x78/0xc9 [libsas]
[<ffffffffa004d4d4>] sas_unregister_dev+0x4f/0xad [libsas]
[<ffffffffa004d5b1>] sas_unregister_domain_devices+0x7f/0xbf [libsas]
[<ffffffffa004c487>] sas_deform_port+0x61/0x1b8 [libsas]
[<ffffffffa004bed0>] sas_phye_loss_of_signal+0x29/0x2b [libsas]
...and kills the awkward "sata domain_device briefly existing in the
domain without an ata_port" state.
Reported-by: Michal Kosciowski <michal.kosciowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use scsi_add_host_with_dma in ata_scsi_add_hosts to pass in the
correct DMA device(ATA host).
Bug report: http://marc.info/?l=linux-ide&m=133177818318187&w=2
Reported-and-tested-by: Jörg Sommer <joerg@alea.gnuu.de>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This variable is incremented from multiple contexts (module_init via
libata-lldds and the libsas discovery thread). Make it atomic to head
off any chance of libsas and libata creating duplicate ids.
Acked-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libsas ata error handling is already async but this does not help the
scan case. Move initial link recovery out from under host->scan_mutex,
and delay synchronization with eh until after all port probe/recovery
work has been queued.
Device ordering is maintained with scan order by still calling
sas_rphy_add() in order of domain discovery.
Since we now scan the domain list when invoking libata-eh we need to be
careful to check for fully initialized ata ports.
Acked-by: Jack Wang <jack_wang@usish.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add ata port runtime suspend/resume/idle callbacks.
Set ->eh_noresume to skip the runtime PM calls on scsi host
in the error handler to avoid dead lock.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently, the device tree of ata port and scsi host looks as below,
/sys/devices/pci0000:00/0000:00:1f.2 (ahci controller)
|-- ata1 (ata port)
|-- host0 (scsi host)
|-- target0:0:0 (scsi target)
|-- 0:0:0:0 (disk)
This patch makes ata port as parent device of scsi host, then it becomes
/sys/devices/pci0000:00/0000:00:1f.2 (ahci controller)
|-- ata1 (ata port)
|-- host0 (scsi host)
|-- target0:0:0 (scsi target)
|-- 0:0:0:0 (disk)
With this change, the ata port runtime PM is easier.
For example, the ata port runtime suspend will happen as,
disk suspend --> scsi target suspend --> scsi host suspend --> ata port
suspend.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add the documentation of parameters of ata_change_queue_depth to silence the warning of make xmldocs
Signed-off-by: Marcos paulo de Souza <marcos.mage@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
They were getting this implicitly by an include of module.h
from device.h -- but we are going to clean that up and break
that include chain, so include export.h explicitly now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Pass queue_depth change requests to libata, and prevent queue_type
changes for ATA devices.
Otherwise:
1/ we do not honor the libata specific restrictions on the queue depth
2/ libsas drivers that do not set sdev->tagged_supported are unable to
change the queue_depth of ata devices via sysfs
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On 16.06.2011 [08:28:39 -0500], Brian King wrote:
> On 06/16/2011 02:51 AM, Tejun Heo wrote:
> > On Wed, Jun 15, 2011 at 04:34:17PM -0700, Nishanth Aravamudan wrote:
> >>> That looks like the right thing to do. For ipr's usage of
> >>> libata, we don't have the concept of a port frozen state, so this flag
> >>> should really never get set. The alternate way to fix this would be to
> >>> only set ATA_PFLAG_FROZEN in ata_port_alloc if ap->ops->error_handler
> >>> is not NULL.
> >>
> >> It seemed like ipr is as you say, but I wasn't sure if it was
> >> appropriate to make the change above in the common libata-scis code or
> >> not. I don't want to break some other device on accident.
> >>
> >> Also, I tried your suggestion, but I don't think that can happen in
> >> ata_port_alloc? ata_port_alloc is allocated ap itself, and it seems like
> >> ap->ops typically gets set only after ata_port_alloc returns?
> >
> > Maybe we can test error_handler in ata_sas_port_start()?
>
> Good point. Since libsas is converted to the new eh now, we would need to have
> this test.
Commit 7b3a24c57d ("ahci: don't enable
port irq before handler is registered") caused a regression for CD-ROMs
attached to the IPR SATA bus on Power machines:
ata_port_alloc: ENTER
ata_port_probe: ata1: bus probe begin
ata1.00: ata_dev_read_id: ENTER
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: ata_dev_read_id: ENTER
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: limiting speed to UDMA7:PIO5
ata1.00: ata_dev_read_id: ENTER
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata1.00: disabled
ata_port_probe: ata1: bus probe end
scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
The FROZEN flag added in that commit is only cleared by the new EH code,
which is not used by ipr. Clear this flag in the SAS code if we don't
support new EH.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* 'for-2.6.40/core' of git://git.kernel.dk/linux-2.6-block: (40 commits)
cfq-iosched: free cic_index if cfqd allocation fails
cfq-iosched: remove unused 'group_changed' in cfq_service_tree_add()
cfq-iosched: reduce bit operations in cfq_choose_req()
cfq-iosched: algebraic simplification in cfq_prio_to_maxrq()
blk-cgroup: Initialize ioc->cgroup_changed at ioc creation time
block: move bd_set_size() above rescan_partitions() in __blkdev_get()
block: call elv_bio_merged() when merged
cfq-iosched: Make IO merge related stats per cpu
cfq-iosched: Fix a memory leak of per cpu stats for root group
backing-dev: Kill set but not used var in bdi_debug_stats_show()
block: get rid of on-stack plugging debug checks
blk-throttle: Make no throttling rule group processing lockless
blk-cgroup: Make cgroup stat reset path blkg->lock free for dispatch stats
blk-cgroup: Make 64bit per cpu stats safe on 32bit arch
blk-throttle: Make dispatch stats per cpu
blk-throttle: Free up a group only after one rcu grace period
blk-throttle: Use helper function to add root throtl group to lists
blk-throttle: Introduce a helper function to fill in device details
blk-throttle: Dynamically allocate root group
blk-cgroup: Allow sleeping while dynamically allocating a group
...
Previously we used Maximum Unmap LBA Count in the Block Limits VPD to
signal the maximum number of sectors we could handle in a single Write
Same command.
Starting with SBC3r26 the Block Limits VPD has an explicit limit on the
number of blocks in a Write Same. This means we can stop abusing a field
related to the Unmap command and let our SAT use the proper value in the
VPD (Maximum Write Same Length).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cc: stable@kernel.org
As per SAT-3 the WWN ID should be included in the VPD page 0x83
(device identification) emulation.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
For historical reasons, libsas uses the scsi host lock as the ata port
lock, and libata always uses the ata host. For the old eh, this was
largely irrelevant since the two locks were never mixed inside the
code. However, the new eh has a case where it nests acquisition of
the host lock inside the port lock (this does look rather deadlock
prone). Obviously this would be an instant deadlock if the port lock
were the host lock, so switch the libsas paths to use the ata host
lock as well.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The function ata_sas_port_init() has always really done its own thing.
However, as a precursor to moving to the libata new eh, it has to be
properly using the standard libata scan paths. This means separating
the current libata scan paths into pieces which can be shared with
libsas and pieces which cant (really just the async call and the host
scan).
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_pio_sectors() expects buffer for each sector to be contained in a
single page; otherwise, it ends up overrunning the first page. This
is achieved by setting queue DMA alignment. If sector_size is smaller
than PAGE_SIZE and all buffers are sector_size aligned, buffer for
each sector is always contained in a single page.
This wasn't applied to ATAPI devices but IDENTIFY_PACKET is executed
as ATA_PROT_PIO and thus uses ata_pio_sectors(). Newer versions of
udev issue IDENTIFY_PACKET with unaligned buffer triggering the
problem and causing oops.
This patch fixes the problem by setting sdev->sector_size to
ATA_SECT_SIZE on ATATPI devices and always setting DMA alignment to
sector_size. While at it, add a warning for the unlikely but still
possible scenario where sector_size is larger than PAGE_SIZE, in which
case the alignment wouldn't be enough.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: John Stanley <jpsinthemix@verizon.net>
Tested-by: John Stanley <jpsinthemix@verizon.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
cmd->serial_number is never tested in any path we reach; therefore we may
remove the call to scsi_cmd_get_serial() inside DEF_SCSI_QCMD, the SCSI
host_lock acquisition surrounding it, and our own SCSI host_lock
unlock+relock cycle.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SCSI commands may be issued between __scsi_add_device() and dev->sdev
assignment, so it's unsafe for ata_qc_complete() to dereference
dev->sdev->locked without checking whether it's NULL or not. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Until now identifying that a device supports WRITE SAME(16) with the
UNMAP bit set has been black magic. Implement support for the SBC-3
Thin Provisioning VPD page and set the TPWS bit.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The current LPM implementation has the following issues.
* Operation order isn't well thought-out. e.g. HIPM should be
configured after IPM in SControl is properly configured. Not the
other way around.
* Suspend/resume paths call ata_lpm_enable/disable() which must only
be called from EH context directly. Also, ata_lpm_enable/disable()
were called whether LPM was in use or not.
* Implementation is per-port when it should be per-link. As a result,
it can't be used for controllers with slave links or PMP.
* LPM state isn't managed consistently. After a link reset for
whatever reason including suspend/resume the actual LPM state would
be reset leaving ap->lpm_policy inconsistent.
* Generic/driver-specific logic boundary isn't clear. Currently,
libahci has to mangle stuff which libata EH proper should be
handling. This makes the implementation unnecessarily complex and
fragile.
* Tied to ALPM. Doesn't consider DIPM only cases and doesn't check
whether the device allows HIPM.
* Error handling isn't implemented.
Given the extent of mismatch with the rest of libata, I don't think
trying to fix it piecewise makes much sense. This patch reimplements
LPM support.
* The new implementation is per-link. The target policy is still
port-wide (ap->target_lpm_policy) but all the mechanisms and states
are per-link and integrate well with the rest of link abstraction
and can work with slave and PMP links.
* Core EH has proper control of LPM state. LPM state is reconfigured
when and only when reconfiguration is necessary. It makes sure that
LPM state is reset when probing for new device on the link.
Controller agnostic logic is now implemented in libata EH proper and
driver implementation only has to deal with controller specifics.
* Proper error handling. LPM config failure is attributed to the
device on the link and LPM is disabled for the link if it fails
repeatedly.
* ops->enable/disable_pm() are replaced with single ops->set_lpm()
which takes @policy and @hints. This simplifies driver specific
implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Link power management related symbols are in confusing state w/ mixed
usages of lpm, ipm and pm. This patch cleans up lpm related symbols
and sysfs show/store functions as follows.
* lpm states - NOT_AVAILABLE, MIN_POWER, MAX_PERFORMANCE and
MEDIUM_POWER are renamed to ATA_LPM_UNKNOWN and
ATA_LPM_{MIN|MAX|MED}_POWER.
* Pre/postfixes are unified to lpm.
* sysfs show/store functions for link_power_management_policy were
curiously named get/put and unnecessarily complex. Renamed to
show/store and simplified.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This change enables my x86 machine to recognize and talk to a
"Native 4K" SATA device.
When I started working on this, I didn't know Matthew Wilcox had
posted a similar patch 2 years ago:
http://git.kernel.org/?p=linux/kernel/git/willy/ata.git;a=shortlog;h=refs/heads/ata-large-sectors
Gwendal Grignou pointed me at the the above code and small portions of
this patch include Matthew's work. That's why Mathew is first on the
"Signed-off-by:". I've NOT included his use of a bitmap to determine
512 vs Native for ATA command block size - just used a simple table.
And bugs are almost certainly mine.
Lastly, the patch has been tested with a native 4K 'Engineering
Sample' drive provided by Hitachi GST.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Grant Grundler <grundler@google.com>
Reviewed-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a scheleton for libata transport class.
All information is read only, exporting information from libata:
- ata_port class: one per ATA port
- ata_link class: one per ATA port or 15 for SATA Port Multiplier
- ata_device class: up to 2 for PATA link, usually one for SATA.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
Remove the current bio flags and reuse the request flags for the bio, too.
This allows to more easily trace the type of I/O from the filesystem
down to the block driver. There were two flags in the bio that were
missing in the requests: BIO_RW_UNPLUG and BIO_RW_AHEAD. Also I've
renamed two request flags that had a superflous RW in them.
Note that the flags are in bio.h despite having the REQ_ name - as
blkdev.h includes bio.h that is the only way to go for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Remove all the trivial wrappers for the cmd_type and cmd_flags fields in
struct requests. This allows much easier grepping for different request
types instead of unwinding through macros.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
libata has two concurrency related limitations.
a. ata_wq which is used for polling PIO has single thread per CPU. If
there are multiple devices doing polling PIO on the same CPU, they
can't be executed simultaneously.
b. ata_aux_wq which is used for SCSI probing has single thread. In
cases where SCSI probing is stalled for extended period of time
which is possible for ATAPI devices, this will stall all probing.
#a is solved by increasing maximum concurrency of ata_wq. Please note
that polling PIO might be used under allocation path and thus needs to
be served by a separate wq with a rescuer.
#b is solved by using the default wq instead and achieving exclusion
via per-port mutex.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Implement ata_scsi_unlock_native_capacity() which will be called
through SCSI layer when block layer notices that partitions on a
device extend beyond the end of the device. It requests EH to unlock
HPA, waits for completion and returns the current device capacity.
This allows libata to unlock HPA on demand instead of having to decide
whether to unlock upfront. Unlocking on demand is safer than
unlocking by upfront because some BIOSes write private data to the
area beyond HPA limit. This was suggested by Ben Hutchings.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ATA_FLAG_DISABLED is only used by drivers which don't use
->error_handler framework and is largely broken. Its only meaningful
function is to make irq handlers skip processing if the flag is set,
which is largely useless and even harmful as it makes those ports more
likely to cause IRQ storms.
Kill ATA_FLAG_DISABLED and makes the callers disable attached devices
instead. ata_port_probe() and ata_port_disable() which manipulate the
flag are also killed.
This simplifies condition check in IRQ handlers. While updating IRQ
handlers, remove ap NULL check as libata guarantees consecutive port
allocation (unoccupied ports are initialized with dummies) and
long-obsolete ATA_QCFLAG_ACTIVE check (checked by ata_qc_from_tag()).
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.
Also introduce a temporary wrapper for backwards compability. This can
be removed after the merge window is closed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix assignment which overwrote SAT ATA PASS-THROUGH command EXTEND
bit setting (ATA_TFLAG_LBA48)
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that the scsi tree has hit mainline we can use the newly added WRITE_SAME_16
define.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
