Preventing the kernel from responding to ICMP Echo Requests messages
can be useful in several ways. The sysctl parameter
'icmp_echo_ignore_all' can be used to prevent the kernel from
responding to IPv4 ICMP echo requests. For IPv6 pings, such
a sysctl kernel parameter did not exist.
Add the ability to prevent the kernel from responding to IPv6
ICMP echo requests through the use of the following sysctl
parameter : /proc/sys/net/ipv6/icmp/echo_ignore_all.
Update the documentation to reflect this change.
Signed-off-by: Virgile Jarry <virgile@acceis.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
For preparing decryption request, several memory chunks are required
(aead_req, sgin, sgout, iv, aad). For submitting the decrypt request to
an accelerator, it is required that the buffers which are read by the
accelerator must be dma-able and not come from stack. The buffers for
aad and iv can be separately kmalloced each, but it is inefficient.
This patch does a combined allocation for preparing decryption request
and then segments into aead_req || sgin || sgout || iv || aad.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the runtime behavior of IP defrag queue:
incoming in-order fragments are added to the end of the current
list/"run" of in-order fragments at the tail.
On some workloads, UDP stream performance is substantially improved:
RX: ./udp_stream -F 10 -T 2 -l 60
TX: ./udp_stream -c -H <host> -F 10 -T 5 -l 60
with this patchset applied on a 10Gbps receiver:
throughput=9524.18
throughput_units=Mbit/s
upstream (net-next):
throughput=4608.93
throughput_units=Mbit/s
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces several helper functions/macros that will be
used in the follow-up patch. No runtime changes yet.
The new logic (fully implemented in the second patch) is as follows:
* Nodes in the rb-tree will now contain not single fragments, but lists
of consecutive fragments ("runs").
* At each point in time, the current "active" run at the tail is
maintained/tracked. Fragments that arrive in-order, adjacent
to the previous tail fragment, are added to this tail run without
triggering the re-balancing of the rb-tree.
* If a fragment arrives out of order with the offset _before_ the tail run,
it is inserted into the rb-tree as a single fragment.
* If a fragment arrives after the current tail fragment (with a gap),
it starts a new "tail" run, as is inserted into the rb-tree
at the end as the head of the new run.
skb->cb is used to store additional information
needed here (suggested by Eric Dumazet).
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use tcf spinlock to protect police action private data from concurrent
modification during dump. (init already uses tcf spinlock when changing
police action state)
Pass tcf spinlock as estimator lock argument to gen_replace_estimator()
during action init.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend gen_new_estimator() to also take stats_lock when re-assigning rate
estimator statistics pointer. (to be used by unlocked actions)
Rename 'stats_lock' to 'lock' and change argument description to explain
that it is now also used for control path.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-introduce mirred list spinlock, that was removed some time ago, in order
to protect it from concurrent modifications, instead of relying on rtnl
lock.
Use tcf spinlock to protect mirred action private data from concurrent
modification in init and dump. Rearrange access to mirred data in order to
be performed only while holding the lock.
Rearrange net dev access to always hold reference while working with it,
instead of relying on rntl lock.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation for removing dependency on rtnl lock from rules update
path, all users of shared objects must take reference while working with
them.
Extend action ops with put_dev() API to be used on net device returned by
get_dev().
Modify mirred action (only action that implements get_dev callback):
- Take reference to net device in get_dev.
- Implement put_dev API that releases reference to net device.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use tcf spinlock to protect vlan action private data from concurrent
modification during dump and init. Use rcu swap operation to reassign
params pointer under protection of tcf lock. (old params value is not used
by init, so there is no need of standalone rcu dereference step)
Remove rtnl assertion that is no longer necessary.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use tcf lock to protect tunnel key action struct private data from
concurrent modification in init and dump. Use rcu swap operation to
reassign params pointer under protection of tcf lock. (old params value is
not used by init, so there is no need of standalone rcu dereference step)
Remove rtnl lock assertion that is no longer required.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move read of skbmod_p rcu pointer to be protected by tcf spinlock. Use tcf
spinlock to protect private skbmod data from concurrent modification during
dump.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use tcf spinlock to protect private simple action data from concurrent
modification during dump. (simple init already uses tcf spinlock when
changing action state)
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use tcf spinlock to protect private sample action data from concurrent
modification during dump and init.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange pedit init code to only access pedit action data while holding
tcf spinlock. Change keys allocation type to atomic to allow it to execute
while holding tcf spinlock. Take tcf spinlock in dump function when
accessing pedit action data.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use tcf spinlock to protect ipt action private data from concurrent
modification during dump. Ipt init already takes tcf spinlock when
modifying ipt state.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use tcf spinlock and rcu to protect params pointer from concurrent
modification during dump and init. Use rcu swap operation to reassign
params pointer under protection of tcf lock. (old params value is not used
by init, so there is no need of standalone rcu dereference step)
Ife action has meta-actions that are compiled as standalone modules. Rtnl
mutex must be released while loading a kernel module. In order to support
execution without rtnl mutex, propagate 'rtnl_held' argument to meta action
loading functions. When requesting meta action module, conditionally
release rtnl lock depending on 'rtnl_held' argument.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use tcf spinlock to protect gact action private state from concurrent
modification during dump and init. Remove rtnl assertion that is no longer
necessary.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use tcf lock to protect csum action struct private data from concurrent
modification in init and dump. Use rcu swap operation to reassign params
pointer under protection of tcf lock. (old params value is not used by
init, so there is no need of standalone rcu dereference step)
Remove rtnl assertion that is no longer necessary.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use tcf spinlock to protect bpf action private data from concurrent
modification during dump and init. Remove rtnl lock assertion that is no
longer necessary.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This path replaces physically contiguous memory arrays
allocated using kmalloc_array() with flexible arrays.
This enables to avoid memory allocation failures on the
systems under a memory stress.
Signed-off-by: Oleg Babin <obabin@virtuozzo.com>
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces wrappers for accessing in/out streams indirectly.
This will enable to replace physically contiguous memory arrays
of streams with flexible arrays (or maybe any other appropriate
mechanism) which do memory allocation on a per-page basis.
Signed-off-by: Oleg Babin <obabin@virtuozzo.com>
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return -ENOIOCTLCMD for unknown ioctl commands. This lets dev_ioctl()
handle generic socket ioctls like SIOCGIFNAME or SIOCGIFINDEX.
PF_PPPOX/PX_PROTO_OL2TP was one of the few socket types not honouring
this mechanism.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrate memset(0) in pppol2tp_copy_stats() to avoid calling it
manually every time.
While there, constify 'stats'.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
pppol2tp_ioctl() has everything in place for handling PPPIOCGL2TPSTATS
on session sockets. We just need to copy the stats and set ->session_id.
As a side effect of sharing session and tunnel code, ->using_ipsec is
properly set even when the request was made using a session socket.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle PPPIOCGL2TPSTATS in pppol2tp_ioctl() if the socket represents a
tunnel. This one is a bit special because the caller may use the tunnel
socket to retrieve statistics of one of its sessions. If the session_id
is set, the corresponding session's statistics are returned, instead of
those of the tunnel. This is handled by the new
pppol2tp_tunnel_copy_stats() helper function.
Set ->tunnel_id and ->using_ipsec out of the conditional, so
that it can be used by the 'else' branch in the following patch.
We cannot do that for ->session_id, because tunnel sockets have to
report the value that was originally passed in 'stats.session_id',
while session sockets have to report their own session_id.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let pppol2tp_ioctl() handle ioctl commands directly. It still relies on
pppol2tp_{session,tunnel}_ioctl() for PPPIOCGL2TPSTATS.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Drop test on 'sk': sock->sk cannot be NULL, or pppox_ioctl() could
not have called us.
* Drop test on 'SOCK_DEAD' state: if this flag was set, the socket
would be in the process of being released and no ioctl could be
running anymore.
* Drop test on 'PPPOX_*' state: we depend on ->sk_user_data to get
the session structure. If it is non-NULL, then the socket is
connected. Testing for PPPOX_* is redundant.
* Retrieve session using ->sk_user_data directly, instead of going
through pppol2tp_sock_to_session(). This avoids grabbing a useless
reference on the socket.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_session_get() is used for two different purposes. If 'tunnel' is
NULL, the session is searched globally in the supplied network
namespace. Otherwise it is searched exclusively in the tunnel context.
Callers always know the context in which they need to search the
session. But some of them do provide both a namespace and a tunnel,
making the semantic of the call unclear.
This patch defines l2tp_tunnel_get_session() for lookups done in a
tunnel and restricts l2tp_session_get() to namespace searches.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper function to figure out if a tunnel is using ipsec.
Also, avoid accessing ->sk_policy directly since it's RCU protected.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 5681 sec 4.2:
To provide feedback to senders recovering from losses, the receiver
SHOULD send an immediate ACK when it receives a data segment that
fills in all or part of a gap in the sequence space.
When a gap is partially filled, __tcp_ack_snd_check already checks
the out-of-order queue and correctly send an immediate ACK. However
when a gap is fully filled, the previous implementation only resets
pingpong mode which does not guarantee an immediate ACK because the
quick ACK counter may be zero. This patch addresses this issue by
marking the one-time immediate ACK flag instead.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent fix of acking immediately in DCTCP on CE status change
has an undesirable side-effect: it also resets TCP ack timer and
disables pingpong mode (interactive session). But the CE status
change has nothing to do with them. This patch addresses that by
using the new one-time immediate ACK flag instead of calling
tcp_enter_quickack_mode().
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new flag to indicate a one-time immediate ACK. This flag is
occasionaly set under specific TCP protocol states in addition to
the more common quickack mechanism for interactive application.
In several cases in the TCP code we want to force an immediate ACK
but do not want to call tcp_enter_quickack_mode() because we do
not want to forget the icsk_ack.pingpong or icsk_ack.ato state.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The static int 'zero' is defined but is never used hence it is
redundant and can be removed. The use of this variable was removed
with commit a158bdd324 ("rxrpc: Fix call timeouts").
Cleans up clang warning:
warning: 'zero' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With SMC-D z/OS sends a test link signal every 10 seconds. Linux is
supposed to answer, otherwise the SMC-D connection breaks.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2018-08-10
Here's one more (most likely last) bluetooth-next pull request for the
4.19 kernel.
- Added support for MediaTek serial Bluetooth devices
- Initial skeleton for controller-side address resolution support
- Fix BT_HCIUART_RTL related Kconfig dependencies
- A few other minor fixes/cleanups
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following batch contains netfilter updates for your net-next tree:
1) Expose NFT_OSF_MAXGENRELEN maximum OS name length from the new OS
passive fingerprint matching extension, from Fernando Fernandez.
2) Add extension to support for fine grain conntrack timeout policies
from nf_tables. As preparation works, this patchset moves
nf_ct_untimeout() to nf_conntrack_timeout and it also decouples the
timeout policy from the ctnl_timeout object, most work done by
Harsha Sharma.
3) Enable connection tracking when conntrack helper is in place.
4) Missing enumeration in uapi header when splitting original xt_osf
to nfnetlink_osf, also from Fernando.
5) Fix a sparse warning due to incorrect typing in the nf_osf_find(),
from Wei Yongjun.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the definitions for LE address resolution enable HCI commands.
When the LE address resolution enable gets changed via HCI commands
make sure that flag gets updated.
Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The definition of static_key_slow_inc() has cpus_read_lock in place. In the
virtio_net driver, XPS queues are initialized after setting the queue:cpu
affinity in virtnet_set_affinity() which is already protected within
cpus_read_lock. Lockdep prints a warning when we are trying to acquire
cpus_read_lock when it is already held.
This patch adds an ability to call __netif_set_xps_queue under
cpus_read_lock().
Acked-by: Jason Wang <jasowang@redhat.com>
============================================
WARNING: possible recursive locking detected
4.18.0-rc3-next-20180703+ #1 Not tainted
--------------------------------------------
swapper/0/1 is trying to acquire lock:
00000000cf973d46 (cpu_hotplug_lock.rw_sem){++++}, at: static_key_slow_inc+0xe/0x20
but task is already holding lock:
00000000cf973d46 (cpu_hotplug_lock.rw_sem){++++}, at: init_vqs+0x513/0x5a0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(cpu_hotplug_lock.rw_sem);
lock(cpu_hotplug_lock.rw_sem);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by swapper/0/1:
#0: 00000000244bc7da (&dev->mutex){....}, at: __driver_attach+0x5a/0x110
#1: 00000000cf973d46 (cpu_hotplug_lock.rw_sem){++++}, at: init_vqs+0x513/0x5a0
#2: 000000005cd8463f (xps_map_mutex){+.+.}, at: __netif_set_xps_queue+0x8d/0xc60
v2: move cpus_read_lock() out of __netif_set_xps_queue()
Cc: "Nambiar, Amritha" <amritha.nambiar@intel.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Fixes: 8af2c06ff4 ("net-sysfs: Add interface for Rx queue(s) map per Tx queue")
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the refcnt is never decremented in case the value is not 1.
Fix it by adding decrement in case the refcnt is not 1.
Reported-by: Vlad Buslov <vladbu@mellanox.com>
Fixes: f71e0ca4db ("net: sched: Avoid implicit chain 0 creation")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
net/decnet/dn_route.c:407:30: warning: Using plain integer as NULL pointer
net/decnet/dn_route.c:1923:22: warning: Using plain integer as NULL pointer
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 GRO over GRE tap is not working while GRO is not set
over the native interface.
gro_list_prepare function updates the same_flow variable
of existing sessions to 1 if their mac headers match the one
of the incoming packet.
same_flow is used to filter out non-matching sessions and keep
potential ones for aggregation.
The number of bytes to compare should be the number of bytes
in the mac headers. In gro_list_prepare this number is set to
be skb->dev->hard_header_len. For GRE interfaces this hard_header_len
should be as it is set in the initialization process (when GRE is
created), it should not be overridden. But currently it is being overridden
by the value that is actually supposed to represent the needed_headroom.
Therefore, the number of bytes compared in order to decide whether the
the mac headers are the same is greater than the length of the headers.
As it's documented in netdevice.h, hard_header_len is the maximum
hardware header length, and needed_headroom is the extra headroom
the hardware may need.
hard_header_len is basically all the bytes received by the physical
till layer 3 header of the packet received by the interface.
For example, if the interface is a GRE tap then the needed_headroom
should be the total length of the following headers:
IP header of the physical, GRE header, mac header of GRE.
It is often used to calculate the MTU of the created interface.
This patch removes the override of the hard_header_len, and
assigns the calculated value to needed_headroom.
This way, the comparison in gro_list_prepare is really of
the mac headers, and if the packets have the same mac headers
the same_flow will be set to 1.
Performance testing: 45% higher bandwidth.
Measuring bandwidth of single-stream IPv4 TCP traffic over IPv6
GRE tap while GRO is not set on the native.
NIC: ConnectX-4LX
Before (GRO not working) : 7.2 Gbits/sec
After (GRO working): 10.5 Gbits/sec
Signed-off-by: Maria Pasechnik <mariap@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a port to be able to use EEE, both the MAC and the PHY must
support EEE. A phy can be provided by both a phydev or phylink. Verify
at least one of these exist, not just phydev.
Fixes: aab9c4067d ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an SMC socket is connecting it is decided whether fallback to
TCP is needed. To avoid races between connect and ioctl move the
sock lock before the use_fallback check.
Reported-by: syzbot+5b2cece1a8ecb2ca77d8@syzkaller.appspotmail.com
Reported-by: syzbot+19557374321ca3710990@syzkaller.appspotmail.com
Fixes: 1992d99882 ("net/smc: take sock lock in smc_ioctl()")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without setsockopt SO_SNDBUF and SO_RCVBUF settings, the sysctl
defaults net.ipv4.tcp_wmem and net.ipv4.tcp_rmem should be the base
for the sizes of the SMC sndbuf and rcvbuf. Any TCP buffer size
optimizations for servers should be ignored.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoking shutdown for a socket in state SMC_LISTEN does not make
sense. Nevertheless programs like syzbot fuzzing the kernel may
try to do this. For SMC this means a socket refcounting problem.
This patch makes sure a shutdown call for an SMC socket in state
SMC_LISTEN simply returns with -ENOTCONN.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AF_RXRPC has a keepalive message generator that generates a message for a
peer ~20s after the last transmission to that peer to keep firewall ports
open. The implementation is incorrect in the following ways:
(1) It mixes up ktime_t and time64_t types.
(2) It uses ktime_get_real(), the output of which may jump forward or
backward due to adjustments to the time of day.
(3) If the current time jumps forward too much or jumps backwards, the
generator function will crank the base of the time ring round one slot
at a time (ie. a 1s period) until it catches up, spewing out VERSION
packets as it goes.
Fix the problem by:
(1) Only using time64_t. There's no need for sub-second resolution.
(2) Use ktime_get_seconds() rather than ktime_get_real() so that time
isn't perceived to go backwards.
(3) Simplifying rxrpc_peer_keepalive_worker() by splitting it into two
parts:
(a) The "worker" function that manages the buckets and the timer.
(b) The "dispatch" function that takes the pending peers and
potentially transmits a keepalive packet before putting them back
in the ring into the slot appropriate to the revised last-Tx time.
(4) Taking everything that's pending out of the ring and splicing it into
a temporary collector list for processing.
In the case that there's been a significant jump forward, the ring
gets entirely emptied and then the time base can be warped forward
before the peers are processed.
The warping can't happen if the ring isn't empty because the slot a
peer is in is keepalive-time dependent, relative to the base time.
(5) Limit the number of iterations of the bucket array when scanning it.
(6) Set the timer to skip any empty slots as there's no point waking up if
there's nothing to do yet.
This can be triggered by an incoming call from a server after a reboot with
AF_RXRPC and AFS built into the kernel causing a peer record to be set up
before userspace is started. The system clock is then adjusted by
userspace, thereby potentially causing the keepalive generator to have a
meltdown - which leads to a message like:
watchdog: BUG: soft lockup - CPU#0 stuck for 23s! [kworker/0:1:23]
...
Workqueue: krxrpcd rxrpc_peer_keepalive_worker
EIP: lock_acquire+0x69/0x80
...
Call Trace:
? rxrpc_peer_keepalive_worker+0x5e/0x350
? _raw_spin_lock_bh+0x29/0x60
? rxrpc_peer_keepalive_worker+0x5e/0x350
? rxrpc_peer_keepalive_worker+0x5e/0x350
? __lock_acquire+0x3d3/0x870
? process_one_work+0x110/0x340
? process_one_work+0x166/0x340
? process_one_work+0x110/0x340
? worker_thread+0x39/0x3c0
? kthread+0xdb/0x110
? cancel_delayed_work+0x90/0x90
? kthread_stop+0x70/0x70
? ret_from_fork+0x19/0x24
Fixes: ace45bec6d ("rxrpc: Fix firewall route keepalive")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
net/netfilter/nfnetlink_osf.c:274:24: warning:
Using plain integer as NULL pointer
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
