Existing Intel xHCI controllers require a delay of 1 mS,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.
Verified CherryView / Braswell platforms go through over
5000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first four fixes was for v4.3-rc7, but it is too late
at that time, and other two small fixes are for possible NULL
pointer issue.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWTCtwAAoJEEhZKYFQ1nG7KpUH+QHw/KjEga4r4BnT6WUMhcZe
BqxZXDCSp1kZKYyxiBy69HlCcCnREC3sjpkWEyPEZUGCMPIyA1phnF0H6Qtb+7Pq
2qBJan82jXnetWLggKTDpU3vgEJL6xZ9LTv2RIZkz5cR7iFLnBF63djB461v86pl
lnSfFHtEKhSFlD1qRhlvO9rl8pOO5XYT9IOOvQi/D1llGBfhu7XRlld8Iv6xxpwA
yBTWWv26Ct51TNtmTt+EpO0VC+/JzyrA2s1zkrZyoPvhrLULCir/+ALHWSkdCdWg
JZedk3w/bxzyinQfIllmcz9kKIkoZSeij6dQAiSHRjSDRCUvRlLOF3hpnBlvok8=
=HJSS
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
USB Chipidea Fixes for v4.4-rc2
The first four fixes was for v4.3-rc7, but it is too late
at that time, and other two small fixes are for possible NULL
pointer issue.
Pull s390 fixes from Martin Schwidefsky:
"Assorted bug fixes, the mlock2 system call gets added, and one
improvement. The boot from dasd devices is now possible from a wider
range of devices"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: remove SALIPL loader
s390: wire up mlock2 system call
s390: remove g5 elf platform support
s390: avoid cache aliasing under z/VM and KVM
s390/sclp: _sclp_wait_int(): retain full PSW mask
s390/zcrypt: Fix initialisation when zcrypt is built-in
s390/zcrypt: Fix kernel crash on systems without AP bus support
s390: add support for ipl devices in subchannel sets > 0
s390/ipl: fix out of bounds access in scpdata_write
s390/pci_dma: improve debugging of errors during dma map
s390/pci_dma: handle dma table failures
s390/pci_dma: unify label of invalid translation table entries
s390/syscalls: remove system call number calculation
s390/cio: simplify css_generate_pgid
s390/diag: add a s390 prefix to the diagnose trace point
s390/head: fix error message on unsupported hardware
Change-Id: Id6514f2fb6e002437fdbe99353d5d35f4ac736c7
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Change-Id: Ifbb0c06680494bfa04d0be5e5941d31ae2e5ef28
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Change-Id: I62b892a22af37b32e6b4aefca80a25cf45426ed2
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
We don't need the last VM use any more, keep the owner directly.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <davdi1.zhou@amd.com>
It's not a good idea to duplicate that code.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <davdi1.zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Fix the indentation and move the VM functions to the structures.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <davdi1.zhou@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Unify the two code path again, cause they do pretty much the same thing.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <davdi1.zhou@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
reset-gpios is more clear than rst-gpio.
This change has been done as one atomic commit but it
does breaks compatability with older dtbs.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds in the required DT node for the c8sectpfe
Linux DVB demux driver which allows the tsin channels
to be used on an upstream kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adding these properties makes the I2C bus to the demodulators much
more reliable, and we no longer suffer from I2C errors when tuning.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When in FE_TUNE_MODE_ONESHOT the frontend must report
the actual capabilities so user can take appropriate
action.
With frontends that can't do auto inversion this is done
by dvb-core automatically so CAN_INVERSION_AUTO is valid.
However, when in FE_TUNE_MODE_ONESHOT this is not true.
So only set FE_CAN_INVERSION_AUTO in modes other than
FE_TUNE_MODE_ONESHOT
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The SPI core always reports the MODALIAS uevent as "spi:<modalias>"
regardless of the mechanism that was used to register the device
(i.e: OF or board code) and the table that is used later to match
the driver with the device (i.e: SPI id table or OF match table).
So drivers needs to export the SPI id table and this be built into
the module or udev won't have the necessary information to autoload
the needed driver module when the device is added.
But this means that OF-only drivers needs to have both OF and SPI id
tables that have to be kept in sync and also the dev node compatible
manufacturer prefix is stripped when reporting the MODALIAS. Which can
lead to issues if two vendors use the same SPI device name for example.
To avoid the above, the SPI core behavior may be changed in the future
to not require an SPI device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table even when
is unused now to prevent breaking module loading when the core changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/media/pci/ddbridge/ddbridge-core.c:89
incorrect check for negative return
Return type of wait_event_timeout is signed long not int and the
return type is >=0 always thus the negative check is unnecessary..
As stat is used here exclusively its type is simply changed and the
negative return check dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When diagnosing a unrelated bug for someone on irc, it would seem the hardware can
be brought up by the BIOS with the embedded displayport using the SPLL for spread spectrum.
Right now this is not handled well in i915, and it calculates the crtc needs to
be reprogrammed on the first modeset without SSC, but the SPLL itself was kept
active. Fix this by exposing SPLL as a shared pll that will not be returned
by intel_get_shared_dpll; you have to know it exists to use it.
Changes since v1:
- Create a separate dpll_hw_state.spll for spll, and use
separate pll functions for spll.
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Gabriel Feceoru <gabriel.feceoru@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447681332-6318-1-git-send-email-maarten.lankhorst@linux.intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The permissions in mark_rodata_ro trigger a build error
with STRICT_MM_TYPECHECKS. Fix this by introducing
PAGE_KERNEL_ROX for the same reasons as PAGE_KERNEL_RO.
From Ard:
"PAGE_KERNEL_EXEC has PTE_WRITE set as well, making the range
writeable under the ARMv8.1 DBM feature, that manages the
dirty bit in hardware (writing to a page with the PTE_RDONLY
and PTE_WRITE bits both set will clear the PTE_RDONLY bit in that case)"
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The asynchronous, merged implementations of AES in CBC, CTR and XTS
modes are preferred when available (i.e., when instantiating ablkciphers
explicitly). However, the synchronous core AES cipher combined with the
generic CBC mode implementation will produce a 'cbc(aes)' blkcipher that
is callable asynchronously as well. To prevent this implementation from
being used when the accelerated asynchronous implemenation is also
available, lower its priority to 250 (i.e., below the asynchronous
module's priority of 300).
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As pointed out by Russell King in response to the proposed ARM version
of this code, the sequence to switch between the UEFI runtime mapping
and current's actual userland mapping (and vice versa) is potentially
unsafe, since it leaves a time window between the switch to the new
page tables and the TLB flush where speculative accesses may hit on
stale global TLB entries.
So instead, use non-global mappings, and perform the switch via the
ordinary ASID-aware context switch routines.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
With gen < 9 we have had always 50Mhz units as our hw
ratio. With gen >= 9 the hw ratio changed to 16.667Mhz (50/3).
The result was that our gpu frequency tracing started to output
values 3 times larger than expected due to hardcoded scaling
value. Fix this by using Use intel_gpu_freq() when generating Mhz
value from ratio for 'intel_gpu_freq_change' trace event.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92591
Cc: stable@vger.kernel.org # v4.3+
Reported-by: Eero Tamminen <eero.t.tamminen@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447776866-29384-1-git-send-email-mika.kuoppala@intel.com
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Reported-by: coverity (CID 1324138)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
of_match_device could return NULL, and so cause a NULL pointer
dereference later. Renaming tmp_dev to of_id (like all others do) in the
process.
Reported-by: coverity (CID 1324135)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
This patch is to support load and unload gadget driver in full OTG mode.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Jiada Wang <jiada_wang@mentor.com>
Cc: <stable@vger.kernel.org> #v4.0+
Since the ci->role will be set after the host role start is complete, there
will be nobody cared irq during start host if usb irq enabled. This error
can be reproduced on i.mx6 sololite EVK board by:
1. disable otg id irq(IDIE) and disable all real otg properties of usbotg1
in dts.
2. boot up the board with ID cable and usb device connected.
3. echo gadget > /sys/kernel/debug/ci_hdrc.0/role
4. echo host > /sys/kernel/debug/ci_hdrc.0/role
5. irq 212: nobody cared.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
For imx27, it needs three clocks to let the controller work,
the old code is wrong, and usbmisc has not included clock handling
code any more. Without this patch, it will cause below data
abort when accessing usbmisc registers.
usbcore: registered new interface driver usb-storage
Unhandled fault: external abort on non-linefetch (0x008) at 0xf4424600
pgd = c0004000
[f4424600] *pgd=10000452(bad)
Internal error: : 8 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.1.0-next-20150701-dirty #3089
Hardware name: Freescale i.MX27 (Device Tree Support)
task: c7832b60 ti: c783e000 task.ti: c783e000
PC is at usbmisc_imx27_init+0x4c/0xbc
LR is at usbmisc_imx27_init+0x40/0xbc
pc : [<c03cb5c0>] lr : [<c03cb5b4>] psr: 60000093
sp : c783fe08 ip : 00000000 fp : 00000000
r10: c0576434 r9 : 0000009c r8 : c7a773a0
r7 : 01000000 r6 : 60000013 r5 : c7a776f0 r4 : c7a773f0
r3 : f4424600 r2 : 00000000 r1 : 00000001 r0 : 00000001
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 0005317f Table: a0004000 DAC: 00000017
Process swapper (pid: 1, stack limit = 0xc783e190)
Stack: (0xc783fe08 to 0xc7840000)
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: <stable@vger.kernel.org> #v4.1+
Acked-by: Shawn Guo <shawnguo@kernel.org>
Some i.mx platforms need three clocks to let controller work, but
others only need one, refine clock operation to adapt for all
platforms, it fixes a regression found at i.mx27.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: <stable@vger.kernel.org> #v4.1+
- Do not change the key of an object in a rbtree, this time it was
the one for DSOs lookup by its long_name, and the noticed symptom was
with 'perf buildid-list --with-hits' (Adrian Hunter)
- 'perf inject' is a pipe, events it doesn't touch should be passed
on, PERF_RECORD_LOST wasn't, fix it (Adrian Hunter)
- Make 'perf buildid-list' request event ordering, as it needs to
first get the mmap events to be able to mark wich DSOs had hits
(Adrian Hunter)
- Fix memory leaks on failure in 'perf probe' (Masami Hiramatsu, Wang Nan)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wIL5
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Do not change the key of an object in a rbtree, this time it was
the one for DSOs lookup by its long_name, and the noticed symptom was
with 'perf buildid-list --with-hits' (Adrian Hunter)
- 'perf inject' is a pipe, events it doesn't touch should be passed
on, PERF_RECORD_LOST wasn't, fix it (Adrian Hunter)
- Make 'perf buildid-list' request event ordering, as it needs to
first get the mmap events to be able to mark wich DSOs had hits
(Adrian Hunter)
- Fix memory leaks on failure in 'perf probe' (Masami Hiramatsu, Wang Nan)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Changeset 4d73270192ec('scripts/kernel-doc: Replacing highlights
hash by an array') broke compatibility of the kernel-doc script with
older versions of perl by using "keys ARRAY" syntax with is available
only on Perl 5.12 or newer, according with:
http://perldoc.perl.org/functions/keys.html
Restore backward compatibility by replacing "foreach my $k (keys ARRAY)"
by a C-like variant: "for (my $k = 0; $k < !ARRAY; $k++)"
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
First round of fixes for this -rc cycle. We have the
usual set of miscellaneous fixes. The important
thing here is support for Intel Broxton SoC on dwc3,
some fixes for Rockchip SoCs on dwc2 and a fix on
dwc3 to let it report lower speeds than
USB_SPEED_SUPER.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LniW
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.4-rc2
First round of fixes for this -rc cycle. We have the
usual set of miscellaneous fixes. The important
thing here is support for Intel Broxton SoC on dwc3,
some fixes for Rockchip SoCs on dwc2 and a fix on
dwc3 to let it report lower speeds than
USB_SPEED_SUPER.
Pull networking fixes from David Miller:
1) Fix list tests in netfilter ingress support, from Florian Westphal.
2) Fix reversal of input and output interfaces in ingress hook
invocation, from Pablo Neira Ayuso.
3) We have a use after free in r8169, caught by Dave Jones, fixed by
Francois Romieu.
4) Splice use-after-free fix in AF_UNIX frmo Hannes Frederic Sowa.
5) Three ipv6 route handling bug fixes from Martin KaFai Lau:
a) Don't create clone routes not managed by the fib6 tree
b) Don't forget to check expiration of DST_NOCACHE routes.
c) Handle rt->dst.from == NULL properly.
6) Several AF_PACKET fixes wrt transport header setting and SKB
protocol setting, from Daniel Borkmann.
7) Fix thunder driver crash on shutdown, from Pavel Fedin.
8) Several Mellanox driver fixes (max MTU calculations, use of correct
DMA unmap in TX path, etc.) from Saeed Mahameed, Tariq Toukan, Doron
Tsur, Achiad Shochat, Eran Ben Elisha, and Noa Osherovich.
9) Several mv88e6060 DSA driver fixes (wrong bit definitions for
certain registers, etc.) from Neil Armstrong.
10) Make sure to disable preemption while updating per-cpu stats of ip
tunnels, from Jason A. Donenfeld.
11) Various ARM64 bpf JIT fixes, from Yang Shi.
12) Flush icache properly in ARM JITs, from Daniel Borkmann.
13) Fix masking of RX and TX interrupts in ravb driver, from Masaru
Nagai.
14) Fix netdev feature propagation for devices not implementing
->ndo_set_features(). From Nikolay Aleksandrov.
15) Big endian fix in vmxnet3 driver, from Shrikrishna Khare.
16) RAW socket code increments incorrect SNMP counters, fix from Ben
Cartwright-Cox.
17) IPv6 multicast SNMP counters are bumped twice, fix from Neil Horman.
18) Fix handling of VLAN headers on stacked devices when REORDER is
disabled. From Vlad Yasevich.
19) Fix SKB leaks and use-after-free in ipvlan and macvlan drivers, from
Sabrina Dubroca.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
MAINTAINERS: Update Mellanox's Eth NIC driver entries
net/core: revert "net: fix __netdev_update_features return.." and add comment
af_unix: take receive queue lock while appending new skb
rtnetlink: fix frame size warning in rtnl_fill_ifinfo
net: use skb_clone to avoid alloc_pages failure.
packet: Use PAGE_ALIGNED macro
packet: Don't check frames_per_block against negative values
net: phy: Use interrupts when available in NOLINK state
phy: marvell: Add support for 88E1540 PHY
arm64: bpf: make BPF prologue and epilogue align with ARM64 AAPCS
macvlan: fix leak in macvlan_handle_frame
ipvlan: fix use after free of skb
ipvlan: fix leak in ipvlan_rcv_frame
vlan: Do not put vlan headers back on bridge and macvlan ports
vlan: Fix untag operations of stacked vlans with REORDER_HEADER off
via-velocity: unconditionally drop frames with bad l2 length
ipg: Remove ipg driver
dl2k: Add support for IP1000A-based cards
snmp: Remove duplicate OUTMCAST stat increment
net: thunder: Check for driver data in nicvf_remove()
...
We would scan out the memory around them if an upscale was attempted,
and would just scan out incorrectly for downscaling.
Signed-off-by: Eric Anholt <eric@anholt.net>
vc4_plane_init() returns an ERR_PTR on error, it doesn't return NULL.
This was obviously intended because the next lines call
PTR_ERR(primary_plane) already.
Fixes: c8b75bca92 ('Eric Anholt <eric@anholt.net>')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Connector cannot be null because it is a list entry, ie accessed at an
offset from the positions of the list structure pointers themselves.
Generated by: scripts/coccinelle/iterators/itnull.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Eric Anholt <eric@anholt.net>
drivers/gpu/drm/vc4/vc4_drv.c:248:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Eric Anholt <eric@anholt.net>
Eugenia (Jenny) Emantayev is replacing Amir Vadai as the
mlx4 Ethernet driver maintainer.
Saeed Mahameed is assigned to maintain mlx5 Eth functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 00ee592717 ("net: fix __netdev_update_features return
on ndo_set_features failure")
and adds a comment explaining why it's okay to return a value other than
0 upon error. Some drivers might actually change flags and return an
error so it's better to fire a spurious notification rather than miss
these.
CC: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While possibly in future we don't necessarily need to use
sk_buff_head.lock this is a rather larger change, as it affects the
af_unix fd garbage collector, diag and socket cleanups. This is too much
for a stable patch.
For the time being grab sk_buff_head.lock without disabling bh and irqs,
so don't use locked skb_queue_tail.
Fixes: 869e7c6248 ("net: af_unix: implement stream sendpage support")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warning:
CC net/core/rtnetlink.o
net/core/rtnetlink.c: In function ‘rtnl_fill_ifinfo’:
net/core/rtnetlink.c:1308:1: warning: the frame size of 2864 bytes is larger than 2048 bytes [-Wframe-larger-than=]
}
^
by splitting up the huge rtnl_fill_ifinfo into some smaller ones, so we
don't have the huge frame allocations at the same time.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. new skb only need dst and ip address(v4 or v6).
2. skb_copy may need high order pages, which is very rare on long running server.
Signed-off-by: Junwei Zhang <linggao.zjw@alibaba-inc.com>
Signed-off-by: Martin Zhang <martinbj2008@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use PAGE_ALIGNED(...) instead of open-coding it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
rb->frames_per_block is an unsigned int, thus can never be negative.
Also fix spacing in the calculation of frames_per_block.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NOLINK state will poll the phy once a second to see if the link
has come up. If the phy has an interrupt line, this polling can be
skipped, since the phy should interrupt when the link returns.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E1540 can be found embedded in the Marvell 88E6352 switch. It
is compatible with the 88E1510, so add support for it, using the
88E1510 specific functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
