The code for the b44_wap54g10_workaround was never included, because
the config option was wrong. The nvram_get function was never in
mainline kernel, only in external OpenWrt patches.
The code should be compiled in when CONFIG_BCM47XX is selected and not
when CONFIG_SSB_DRIVER_MIPS is selected, because nvram_getenv is only
available on bcm47xx platforms and now in the mainline kernel code.
Using an include is better than a second function declaration, to fix
this when the function signature changes.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong of initializer entry was modified.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver's AUTHOR was changed to "Toshiharu Okada" from "Masayuki Ohtake".
I update the Kconfig, renamed "Topcliff" to "EG20T".
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 58933c64(ucc_geth: Fix the wrong the Rx/Tx FIFO size),
the UCC_GETH_UTFTT_INIT is set to 512 based on the recommendation
of the QE Reference Manual. But that will sometimes cause tx halt
while working in half duplex mode.
According to errata draft QE_GENERAL-A003(High Tx Virtual FIFO
threshold size can cause UCC to halt), setting UTFTT less than
[(UTFS x (M - 8)/M) - 128] will prevent this from happening
(M is the minimum buffer size).
The patch changes UTFTT back to 256.
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: Jean-Denis Boyer <jdboyer@media5corp.com>
Cc: Andreas Schmitz <Andreas.Schmitz@riedel.net>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some debug information about ehea not being able to
allocate enough spaces. Also it correctly updates the amount of available
skb.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HSO driver incorrectly creates a serial device instead of a net
device when disable_net is set. It shouldn't create anything for the
network interface.
Signed-off-by: Filip Aben <f.aben@option.com>
Reported-by: Piotr Isajew <pki@ex.com.pl>
Reported-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We register lapb when tty is created, but unregister it only when the
device is UP. So move the lapb_unregister to x25_asy_close_tty after
the device is down.
The old behaviour causes ldisc switching to fail each second attempt,
because we noted for us that the device is unused, so we use it the
second time, but labp layer still have it registered, so it fails
obviously.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Sergey Lapin <slapin@ossfans.org>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Tested-by: Sergey Lapin <slapin@ossfans.org>
Tested-by: Mikhail Ulyanov <ulyanov.mikhail@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were truncating the number of unicast and multicast MAC addresses
supported. Additionally, we were incorrectly computing the MAC Address
hash (a "1 << N" where we needed a "1ULL << N").
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating unit from ird might return several error codes
not only -EAGAIN, so it should not be changed and returned
precisely. Same time unit release procedure should be invoked
only if device is unregistering.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
"aup->enable" holds already the address pointing to the MAC enable
register. The bug was introduced by commit d0e7cb:
"au1000-eth: remove volatiles, switch to I/O accessors".
CC: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incorrect rcu check was used as rcu isn't done
under mutex here. Force check to 1 for now,
to stop it from complaining.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Running randconfig with ktest.pl I hit this bug:
[ 16.101158] ICN-ISDN-driver Rev 1.65.6.8 mem=0x000d0000
[ 16.106376] icn: (line0) ICN-2B, port 0x320 added
[ 16.111064] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: c1642880
[ 16.111066]
[ 16.121214] Pid: 1, comm: swapper Not tainted 2.6.37-rc2-test-00124-g6656b3f #8
[ 16.128499] Call Trace:
[ 16.130942] [<c0f51662>] ? printk+0x1d/0x23
[ 16.135200] [<c0f5153f>] panic+0x5c/0x162
[ 16.139286] [<c0d62a9a>] ? icn_addcard+0x6d/0xbe
[ 16.143975] [<c0445783>] print_tainted+0x0/0x8c
[ 16.148582] [<c1642880>] ? icn_init+0xd8/0xdf
[ 16.153012] [<c1642880>] icn_init+0xd8/0xdf
[ 16.157271] [<c04012e5>] do_one_initcall+0x8c/0x143
[ 16.162222] [<c16427a8>] ? icn_init+0x0/0xdf
[ 16.166566] [<c15f1a05>] kernel_init+0x13f/0x1da
[ 16.171256] [<c15f18c6>] ? kernel_init+0x0/0x1da
[ 16.175945] [<c0403bfe>] kernel_thread_helper+0x6/0x10
[ 16.181181] panic occurred, switching back to text console
Looking into it I found that the stack was corrupted by the assignment
of the Rev #. The variable rev is given 10 bytes, and in this output the
characters that were copied was: " 1.65.6.8 $". Which was 11 characters
plus the null ending character for a total of 12 bytes, thus corrupting
the stack.
This patch ups the variable size to 20 bytes as well as changes the
strcpy to strncpy. I also added a check to make sure '$' is found.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix unbalanced call to sdio_release_host() on the error path.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new vendor for Broadcom 4318.
Signed-off-by: Daniel Klaffenbach <danielklaffenbach@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that using ath9k_hw_stoppcurecv to stop rx dma is not enough.
When it's time to stop DMA, the PCU is still busy, so the rx enable
bit never clears.
Using ath9k_hw_abortpcurecv helps with getting rx stopped much faster,
with this change, I cannot reproduce the rx stop related WARN_ON anymore.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some aspects of PHY initialization are board dependent, things like
indicator LED connections and some clocking modes cannot be determined
by probing. The dev_flags element of struct phy_device can be used to
control these things if an appropriate value can be passed from the
Ethernet driver. We run into problems however if the PHY connections
are specified by the device tree. There is no way for the Ethernet
driver to know what flags it should pass.
If we are using the device tree, the struct phy_device will be
populated with the device tree node corresponding to the PHY, and we
can extract extra configuration information from there.
The next question is what should the format of that information be?
It is highly device specific, and the device tree representation
should not be tied to any arbitrary kernel defined constants. A
straight forward representation is just to specify the exact bits that
should be set using the "marvell,reg-init" property:
phy5: ethernet-phy@5 {
reg = <5>;
compatible = "marvell,88e1149r";
marvell,reg-init =
/* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */
<3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */
/* mix %:0, led[0123]:drive low off hiZ */
<3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */
/* default blink periods. */
<3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */
/* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */
<3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */
};
phy6: ethernet-phy@6 {
reg = <6>;
compatible = "marvell,88e1118";
marvell,reg-init =
/* Fix rx and tx clock transition timing */
<2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
/* Adjust LED drive. */
<3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
/* irq, blink-activity, blink-link */
<3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
};
The Marvell PHYs have a page select register at register 22 (0x16), we
can specify any register by its page and register number. These are
the first and second word. The third word contains a mask to be ANDed
with the existing register value, and the fourth word is ORed with the
result to yield the new register value. The new marvell_of_reg_init
function leaves the page select register unchanged, so a call to it
can be dropped into the .config_init functions without unduly
affecting the state of the PHY.
If CONFIG_OF_MDIO is not set, there is no of_node, or no
"marvell,reg-init" property, the PHY initialization is unchanged.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E1149R is 10/100/1000 quad-gigabit Ethernet PHY. The
.config_aneg function can be shared with 88E1118, but it needs its own
.config_init.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The definition of the Marvell PHY page register is not specific to
88E1121, so rename the macro to MII_MARVELL_PHY_PAGE, and use it
throughout.
Suggested-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver appears to be mistaking the permission field with default value
in the case of debug and qlge_irq_type.
Driver is also passing debug as a bitmask into netif_msg_init()
which wants a number of bits. Ron Mercer suggests we should
change this to pass in -1 so the defaults get used instead,
which makes the default much less verbose.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Sonny Rao <sonnyrao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks to me as if the second value of rate_err_array is intended
to be a decimal 625. However, with a leading 0 it becomes an octal
constant, and as such evaluates to a decimal 405.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 496c185c94 "atl1c: Add support
for Atheros AR8152 and AR8152" added the condition:
if (hw->nic_type == athr_l1c || hw->nic_type == athr_l2c_b)
for enabling OTP CLK, and the condition:
if (hw->nic_type == athr_l1c || hw->nic_type == athr_l2c)
for disabling OTP CLK. Since the two previously defined hardware
types are athr_l1c and athr_l2c, the latter condition appears to be
the correct one. Change the former to match.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
VMWare reports that the e1000 driver has a bug when bringing down the
interface, such that interrupts are not disabled in the hardware but the
driver stops reporting that it consumed the interrupt.
The fix is to set the driver's "down" flag later in the routine,
after all the timers and such have exited, preventing the interrupt
handler from being called and exiting early without handling the
interrupt.
CC: Anupam Chanda <anupamc@vmware.com>
CC: stable kernel <stable@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since interrupts are enabled only when open is called on the interface,
Attempting a firmware update operation when interface is down could lead to
partial success or failure of operation. This fix fails the request if
netif_running is false.
Signed-off-by: Sarveshwar Bandi <Sarveshwar.Bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VORTEX_PCI() could return NULL so it needs to be casted before
accessing any member of struct pci_dev. This fixes following
build failure. Likewise VORTEX_EISA() was changed also.
CC [M] drivers/net/3c59x.o
drivers/net/3c59x.c: In function 'acpi_set_WOL':
drivers/net/3c59x.c:3211:39: warning: dereferencing 'void *' pointer
drivers/net/3c59x.c:3211:39: error: request for member 'current_state' in something not a structure or union
make[3]: *** [drivers/net/3c59x.o] Error 1
make[2]: *** [drivers/net/3c59x.o] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipg.c:
The id [SUNDANCE, 0x1021] (=[0x13f0, 0x1021]) is defined
at dl2k.h and ipg.c.
But this device works better with dl2k driver.
This problem is similar with the commit
[25cca53527
ipg: Remove device claimed by dl2k from pci id table]
at 11 Feb 2010.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_netdev() is not checked here for NULL return value. dev is
check instead. It might lead to NULL dereference of ndev.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting tid information in the TX header is required only for QoS
frames. Not handling this case causes severe data loss with some APs.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RCU conversion in IGMP code done in net-next-2.6 raised a race in
__bond_resend_igmp_join_requests().
It iterates in_dev->mc_list without appropriate protection (RTNL, or
read_lock on in_dev->mc_list_lock).
Another cpu might delete an entry while we use it and trigger a fault.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
irq_of_parse_and_map() has an unsigned return type.
Testing for a negative error value doesn't work here.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_init_one() should return negative value on error.
By mistake it returns ENODEV instead of -ENODEV.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I am not family with RealTek RTL-8139C+ series 10/100 PCI Ethernet driver.
I try to guess the meaning of RxProtoIP and IPFail.
RxProtoIP stands for received IPv4 packet that upper protocol is not tcp and udp.
!(status & IPFail) is true means that driver correctly to check checksum in IPv4 header.
If these are right, driver will set ip_summed with CHECKSUM_UNNECESSARY for other
upper protocol, e.g. sctp, igmp protocol. This will cause protocol stack ignores
checksum check for packets with invalid checksum.
This patch is only compile-test.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If r8196 received packets with invalid sctp/igmp(not tcp, udp) checksum, r8196 set skb->ip_summed
wit CHECKSUM_UNNECESSARY. This cause that upper protocol don't check checksum field.
I am not family with r8196 driver. I try to guess the meaning of RxProtoIP and IPFail.
RxProtoIP stands for received IPv4 packet that upper protocol is not tcp and udp.
!(opts1 & IPFail) is true means that driver correctly to check checksum in IPv4 header.
If it's right, I think we should not set ip_summed wit CHECKSUM_UNNECESSARY for my sctp packets
with invalid checksum.
If it's not right, please tell me.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AR9287 based PCI & USB devices are differed in eeprom start offset.
So set proper the offset for HTC devices to read nvram correctly.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Treat new PIDs (0xA704, 0x1200) as AR7010 devices.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added new VID/PIDs into supported devices list
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update pm_qos before removing it in deinit_device to prevent this
warning:
pm_qos_update_request() called for unknown object.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
usb_wait_anchor_empty_timeout's @timeout
wants milliseconds and not jiffies.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (66 commits)
can-bcm: fix minor heap overflow
gianfar: Do not call device_set_wakeup_enable() under a spinlock
ipv6: Warn users if maximum number of routes is reached.
docs: Add neigh/gc_thresh3 and route/max_size documentation.
axnet_cs: fix resume problem for some Ax88790 chip
ipv6: addrconf: don't remove address state on ifdown if the address is being kept
tcp: Don't change unlocked socket state in tcp_v4_err().
x25: Prevent crashing when parsing bad X.25 facilities
cxgb4vf: add call to Firmware to reset VF State.
cxgb4vf: Fail open if link_start() fails.
cxgb4vf: flesh out PCI Device ID Table ...
cxgb4vf: fix some errors in Gather List to skb conversion
cxgb4vf: fix bug in Generic Receive Offload
cxgb4vf: don't implement trivial (and incorrect) ndo_select_queue()
ixgbe: Look inside vlan when determining offload protocol.
bnx2x: Look inside vlan when determining checksum proto.
vlan: Add function to retrieve EtherType from vlan packets.
virtio-net: init link state correctly
ucc_geth: Fix deadlock
ucc_geth: Do not bring the whole IF down when TX failure.
...
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (28 commits)
Revert "USB: xhci: Use GFP_ATOMIC under spin_lock"
USB: ohci-jz4740: Fix spelling in MODULE_ALIAS
UWB: Return UWB_RSV_ALLOC_NOT_FOUND rather than crashing on NULL dereference if kzalloc fails
usb: core: fix information leak to userland
usb: misc: iowarrior: fix information leak to userland
usb: misc: sisusbvga: fix information leak to userland
usb: subtle increased memory usage in u_serial
USB: option: fix when the driver is loaded incorrectly for some Huawei devices.
USB: xhci: Use GFP_ATOMIC under spin_lock
usb: gadget: goku_udc: add registered flag bit, fixing build
USB: ehci/mxc: compile fix
USB: Fix FSL USB driver on non Open Firmware systems
USB: the development of the usb tree is now in git
usb: musb: fail unaligned DMA transfers on v1.8 and above
USB: ftdi_sio: add device IDs for Milkymist One JTAG/serial
usb.h: fix ioctl kernel-doc info
usb: musb: gadget: kill duplicate code in musb_gadget_queue()
usb: musb: Fix handling of spurious SESSREQ
usb: musb: fix kernel oops when loading musb_hdrc module for the 2nd time
USB: musb: blackfin: push clkin value to platform resources
...
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
n_gsm: Fix length handling
n_gsm: Copy n2 over when configuring via ioctl interface
serial: bfin_5xx: grab port lock before making port termios changes
serial: bfin_5xx: disable CON_PRINTBUFFER for consoles
serial: bfin_5xx: remove redundant SSYNC to improve TX speed
serial: bfin_5xx: always include DMA headers
vcs: make proper usage of the poll flags
amiserial: Remove unused variable icount
8250: Fix tcsetattr to avoid ioctl(TIOCMIWAIT) hang
tty_ldisc: Fix BUG() on hangup
TTY: restore tty_ldisc_wait_idle
SERIAL: blacklist si3052 chip
drivers/serial/bfin_5xx.c: Fix line continuation defects
tty: prevent DOS in the flush_to_ldisc
8250: add support for Kouwell KW-L221N-2
nozomi: Fix warning from the previous TIOCGCOUNT changes
tty: fix warning in synclink driver
tty: Fix formatting in tty.h
tty: the development tree is now done in git
* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: do not release any memory under 1M in domain 0
xen: events: do not unmask event channels on resume
xen: correct size of level2_kernel_pgt
* 'stable/xen-pcifront-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
MAINTAINERS: Mark XEN lists as moderated
xen-pcifront: fix PCI reference leak
xen-pcifront: Remove duplicate inclusion of headers.
xen: fix memory leak in Xen PCI MSI/MSI-X allocator.
MAINTAINERS: Update mailing list name for Xen pieces.
Delete successive assignments to the same location.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression i;
@@
*i = ...;
i = ...;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_legacy is incorrectly testing PATA_WINBOND_VLB_MODULE instead of
CONFIG_PATA_WINBOND_VLB_MODULE. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "Robert P. J. Day" <rpjday@crashcourse.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SCSI commands may be issued between __scsi_add_device() and dev->sdev
assignment, so it's unsafe for ata_qc_complete() to dereference
dev->sdev->locked without checking whether it's NULL or not. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
