Now we have a set of nested attributes:
IFLA_VFINFO_LIST (NESTED)
IFLA_VF_INFO (NESTED)
IFLA_VF_MAC
IFLA_VF_VLAN
IFLA_VF_TX_RATE
This allows a single set to operate on multiple attributes if desired.
Among other things, it means a dump can be replayed to set state.
The current interface has yet to be released, so this seems like
something to consider for 2.6.34.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize access to the drivers configuration interface.
Also do not allow configuration changes during online/offline
transition.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
z/OS may activate Optimized Latency Mode (OLM) for a connection
through an OSA Express3 adapter, which reduces the number of
allowed concurrent connections, if adapter is used in shared mode.
Create a meaningful message, if activation of an OSA-connection fails
due to an active OLM-connection on the shared OSA-adapter.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OSA supports HW TX checksumming in layer 3 mode. Enable this
feature and remove software fallback used for TSO. Cleanup
checksum bits to indicate OSA can do checksumming only for
IPv4 TCP and UDP.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
transport may be free before ICMP proto unreachable timer expire, so
we should delete active ICMP proto unreachable timer when transport
is going away.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan/macvlan start_xmit() can inform caller of congestion with
NET_XMIT_CN return value. This doesnt mean packet was dropped.
Increment normal stat counters instead of tx_dropped.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP-MD5 sessions have intermittent failures, when route cache is
invalidated. ip_queue_xmit() has to find a new route, calls
sk_setup_caps(sk, &rt->u.dst), destroying the
sk->sk_route_caps &= ~NETIF_F_GSO_MASK
that MD5 desperately try to make all over its way (from
tcp_transmit_skb() for example)
So we send few bad packets, and everything is fine when
tcp_transmit_skb() is called again for this socket.
Since ip_queue_xmit() is at a lower level than TCP-MD5, I chose to use a
socket field, sk_route_nocaps, containing bits to mask on sk_route_caps.
Reported-by: Bhaskar Dutta <bhaskie@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP MD5 support uses percpu data for temporary storage. It currently
disables preemption so that same storage cannot be reclaimed by another
thread on same cpu.
We also have to make sure a softirq handler wont try to use also same
context. Various bug reports demonstrated corruptions.
Fix is to disable preemption and BH.
Reported-by: Bhaskar Dutta <bhaskie@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With RPS inclusion, skb timestamping is not consistent in RX path.
If netif_receive_skb() is used, its deferred after RPS dispatch.
If netif_rx() is used, its done before RPS dispatch.
This can give strange tcpdump timestamps results.
I think timestamping should be done as soon as possible in the receive
path, to get meaningful values (ie timestamps taken at the time packet
was delivered by NIC driver to our stack), even if NAPI already can
defer timestamping a bit (RPS can help to reduce the gap)
Tom Herbert prefer to sample timestamps after RPS dispatch. In case
sampling is expensive (HPET/acpi_pm on x86), this makes sense.
Let admins switch from one mode to another, using a new
sysctl, /proc/sys/net/core/netdev_tstamp_prequeue
Its default value (1), means timestamps are taken as soon as possible,
before backlog queueing, giving accurate timestamps.
Setting a 0 value permits to sample timestamps when processing backlog,
after RPS dispatch, to lower the load of the pre-RPS cpu.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I mistakenly had the error path to use num_pols to decide how
many policies we need to drop (cruft from earlier patch set
version which did not handle socket policies right).
This is wrong since normally we do not keep explicit references
(instead we hold reference to the cache entry which holds references
to policies). drop_pols is set to num_pols if we are holding the
references, so use that. Otherwise we eventually BUG_ON inside
xfrm_policy_destroy due to premature policy deletion.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now there's null check here and also again in the hook. Looking at bridge bits
which are simmilar, port structure is rcu_dereferenced right away in
handle_bridge and passed to hook. Looks nicer.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replace the PCI DMA state API (include/linux/pci-dma.h) with the
DMA equivalents since the PCI DMA state API will be obsolete.
No functional change.
For further information about the background:
http://marc.info/?l=linux-netdev&m=127037540020276&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(Dropped the infiniband part, because Tetsuo modified the related code,
I will send a separate patch for it once this is accepted.)
This patch introduces /proc/sys/net/ipv4/ip_local_reserved_ports which
allows users to reserve ports for third-party applications.
The reserved ports will not be used by automatic port assignments
(e.g. when calling connect() or bind() with port number 0). Explicit
port allocation behavior is unchanged.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new function can be used to read/write large bitmaps via /proc. A
comma separated range format is used for compact output and input
(e.g. 1,3-4,10-10).
Writing into the file will first reset the bitmap then update it
based on the given input.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(Based on Octavian's work, and I modified a lot.)
As we are about to add another integer handling proc function a little
bit of cleanup is in order: add a few helper functions to improve code
readability and decrease code duplication.
In the process a bug is also fixed: if the user specifies a number
with more then 20 digits it will be interpreted as two integers
(e.g. 10000...13 will be interpreted as 100.... and 13).
Behavior for EFAULT handling was changed as well. Previous to this
patch, when an EFAULT error occurred in the middle of a write
operation, although some of the elements were set, that was not
acknowledged to the user (by shorting the write and returning the
number of bytes accepted). EFAULT is now treated just like any other
errors by acknowledging the amount of bytes accepted.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Links for each port are created in sysfs using the device
name, but this could be changed after being added to the
bridge.
As well as being unable to remove interfaces after this
occurs (because userspace tools don't recognise the new
name, and the kernel won't recognise the old name), adding
another interface with the old name to the bridge will
cause an error trying to create the sysfs link.
This fixes the problem by listening for NETDEV_CHANGENAME
notifications and renaming the link.
https://bugzilla.kernel.org/show_bug.cgi?id=12743
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use one set of macro's for all bridge messages.
Note: can't use netdev_XXX macro's because bridge is purely
virtual and has no device parent.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move code around so that the ifdef for NETPOLL_CONTROLLER don't have to
show up in main code path. The control functions should be in helpers
that are only compiled if needed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some RNDIS devices don't respond on the control channel until polled
on the status channel. In particular, this was reported to be the
case for the 2Wire HomePortal 1000SW.
This is roughly based on a patch by John Carr <john.carr@unrouted.co.uk>
which is reported to be needed for use with some Windows Mobile devices
and which is currently applied by Mandriva.
Reported-by: Mark Glassberg <vzeeaxwl@myfairpoint.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Mark Glassberg <vzeeaxwl@myfairpoint.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix xt_TEE build for the case of NF_CONNTRACK=m and
NETFILTER_XT_TARGET_TEE=y:
xt_TEE.c:(.text+0x6df5c): undefined reference to `nf_conntrack_untracked'
4x
Built with all 4 m/y combinations.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ever driver changes the device state, it should write
pci-func number and timestamp in debug registers.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device can go to quiescent state, during which drivers
should refrain from using the device.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci-func class can be other than ethernet in Qlogic CNA device.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Warn user if IDC version mismatch with different class of drivers.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LRO ring, cut-thru mode and specific fw version are not
valid to Qlogic CNA device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Window register is not per pci-func, so caching can
result in expected result.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MSI_MODE, CAPABILITIES_FW and SCRATCHPAD registers are obsolete.
Driver should not use them.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before going for recovery, every pci-func should check fw state,
irrespective of device state. This to avoid unnecssary sending
of command for ctx destroy.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating memory can fail, and since we have the memory we need
in sky2_resume when sky2_suspend is called, just stop the hardware
without freeing the memory it's using.
This avoids the possibility of failing because we can't allocate
memory in sky2_resume(), and allows sharing code with sky2_restart().
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code to bring down all sky2 interfaces and bring it up
again can be reused in sky2_suspend and sky2_resume.
Factor the code to bring the interfaces down into
sky2_all_down and the up code into sky2_all_up.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupts should be masked, then synchronized, and
finally NAPI should be disabled.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_stop_queue does not ensure all in-progress transmits are complete,
so use netif_tx_disable() instead.
Secondly, make sure NAPI polls are disabled before stopping the tx queue,
otherwise sky2_status_intr might trigger a TX queue wakeup between when
we stop the queue and NAPI is disabled.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast settings will be lost on reset, so restore them.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There appears to be an off-by-1 defect in the maximum packet size
copied when copybreak is speified in these modules.
The copybreak module params are specified as:
"Maximum size of packet that is copied to a new buffer on receive"
The tests are changed from "< copybreak" to "<= copybreak"
and moved into new static functions for readability.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the cleanup pass after the removal of e1000e hardware from e1000 some
parameters were missed. Remove them because it is just dead code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding more than 14 mac-vlan adapters on e1000 the driver
would fire a WARN_ON when adding the 15th. The WARN_ON in this
case is completely un-necessary, as the code below the WARN_ON is
directly handling the value the WARN_ON triggered on.
CC: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the following MAC functions are moved from 82598 & 82599 specific
hardware files to common.[ch] to accommodate new silicon changes. Also
fixed some white space issues
* get_san_mac_addr, check_link, set_vmdq, clear_vmdq, clear_vfta,
* set_vfta, fc_enable, init_uta_tables
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't use zero magic "bad" value to check if IXGBE_RSC_CB(skb)->dma
is valid. It is only valid in x86/arm/m68k/alpha architectures and in
spark, powerPC and other architectures it should be ~0. As per
Benjamin Herrenschmidt feedback use a bool flag to decide if
the packet unmapping is delayed in hardware RSC till EOP is reached
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce uc_set_promisc flag to fix enabling of promisc mode
when exceeding the number of supported RAR entries.
Issue discovered by Ben Greear when using mac-vlans.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes from net/ netfilter files
all the unnecessary return; statements that precede the
last closing brace of void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
Signed-off-by: Joe Perches <joe@perches.com>
[Patrick: changed to keep return statements in otherwise empty function bodies]
Signed-off-by: Patrick McHardy <kaber@trash.net>
Make sure all printk messages have a severity level.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Change netfilter asserts to standard WARN_ON. This has the
benefit of backtrace info and also causes netfilter errors
to show up on kerneloops.org.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
