With the nonatomic PCM ops, the system may spew lockdep warnings like:
=============================================
[ INFO: possible recursive locking detected ]
4.2.0-rc1-jeejaval3 #12 Not tainted
---------------------------------------------
aplay/4029 is trying to acquire lock:
(snd_pcm_link_rwsem){.+.+.+}, at: [<ffffffff816fd473>] snd_pcm_stream_lock+0x43/0x60
but task is already holding lock:
(snd_pcm_link_rwsem){.+.+.+}, at: [<ffffffff816fcf29>] snd_pcm_action_nonatomic+0x29/0x80
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(snd_pcm_link_rwsem);
lock(snd_pcm_link_rwsem);
Although this is false-positive as the rwsem is taken always as
read-only for these code paths, it's certainly annoying to see this at
any occasion. A simple fix is to use down_read_nested() in
snd_pcm_stream_lock() that can be called inside another lock.
Reported-by: Vinod Koul <vinod.koul@intel.com>
Reported-by: Jeeja Kp <jeeja.kp@intel.com>
Tested-by: Jeeja Kp <jeeja.kp@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This laptop needs GPIO4 pulled high to enable the headphone amplifier,
and has a mute LED on GPIO3. I modelled the patch on the existing
GPIO4 code which pulls the line low for the same purpose; this time,
the HP amp line is pulled high.
v2: Disable the headphone amplifier when no headphone is connected.
Don't disable power savings to preserve the LED state.
v3: Remove headset-specific hooks and code; this is just a headphone.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a monitor stream is active, the next PCM stream access results in
EBUSY error because of the check in line6_stream_start(). Fix this by
just skipping the submission of pending URBs when the stream is
already running instead.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101431
Cc: <stable@vger.kernel.org> # v4.0+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, the alt PCM open callback returns -EBUSY when an
independent HP is turned off, supposing that it conflicts with the
main PCM. However, obviously, this check is wrong when the
independent HP itself isn't enabled but the alt PCM was explicitly
created via alc_dac_nid by a codec driver.
Reported-and-tested-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x8086280a) and module alias for Broxton
display codec.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Steinberg MI2 and MI4 interfaces are compatible with the USB class
audio spec, but the MIDI part of the devices is reported as a vendor
specific interface.
This patch adds entries to quirks-table.h to recognize the MIDI
endpoints. Audio functionality was already working and is unaffected by
this change.
Signed-off-by: Dominic Sacré <dominic.sacre@gmx.de>
Signed-off-by: Albert Huitsing <albert@huitsing.nl>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Static analysis with cppcheck found the following error:
[sound/core/init.c:118]: (error) Uninitialized variable: err
..this was introduced by commit 2471b6c80a
("ALSA: info: Register proc entries recursively, too") where the call
to snd_info_card_register was removed and no longer setting the error
return in err. When snd_info_create_card_entry fails to allocate a
an entry, the error path exits with garbage in err. Fix is to return
-ENOMEM if entry fails to be allocated.
Fixes: 2471b6c80a ("ALSA: info: Register proc entries recursively, too")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_info_free_entry() function tests whether its argument is NULL and
then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fujitsu Lifebook E780 sets the sequence number 0x0f to only only of
the two headphones, thus the driver tries to assign another as the
line-out, and this results in the inconsistent mapping between the
created jack ctl and the actual I/O. Due to this, PulseAudio doesn't
handle it properly and gets the silent output.
The fix is to ignore the non-HP sequencer checks.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99681
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acer Aspire V5 with ALC282 codec needs the similar quirk like Dell
laptops to support the headset mic. The headset mic pin is 0x19 and
it's not exposed by BIOS, thus we need to fix the pincfg as well.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96201
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Those FIXUPs were applied to the machines through pin quirks, but
recently the PCI_QUIRK makes them can't apply to the machines.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99851
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org> # v4.1
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While the commit [d0a601c278de: ALSA: jack: Fix the id uniqueness
check] fixes the wrong string check, it leads to a worse result -- the
loop in get_available_index() goes into an endless loop. The cause is
that snd_ctl_find_id() returns the object assigned to the numid if
it's set. Thus it points to the previous entry again.
This patch clears the numid field for the next call properly.
Reported-and-tested-by: Tomáš Pružina <pruzinat@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The widget power-save that was enabled in 4.1 kernel seems resulting
in the silent output on VIA codecs by some reason. Some widgets get
wrong power states.
As a quick fix, turn this flag off while keeping power_down_unused
flag. This will bring back to the state of 4.0.x.
Fixes: 688b12cc3c ('ALSA: hda - Use the new power control for VIA codecs')
Reported-and-tested-by: Harald Dunkel <harri@afaics.de>
Cc: <stable@vger.kernel.org> # v4.1
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Thinkpad X250, when attached to a dock, has two headphone outs but
no line out. Make sure we don't try to turn this into one headphone
and one line out (since that disables the headphone amp on the dock).
Alsa-info at http://www.alsa-project.org/db/?f=36f8764e1d782397928feec715d0ef90dfddd4c1
Cc: stable@vger.kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pcm_class sysfs of each PCM substream gives only "none" since the
recent code change to embed the struct device. Fix the code to point
directly to the embedded device object properly.
Fixes: ef46c7af93 ('ALSA: pcm: Embed struct device')
Cc: <stable@vger.kernel.org> # v4.0+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These were sitting on my laptop.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVh+HbAAoJECTWi3JdVIfQ4pEH/0MZfYrxtxtft/Vt8/QYS6ah
U/VBzIEGN7Phv15Eqspww+IKK9nIsuI8Iy+Qbm+gsWUy31m+07Lg/LuE6rEetbg2
xsJ/f4J81rCQTBvrvDXCevvTnw5W6vy9F5ZEi6RmXSTw8W6NDbAmBZXnZ8yCapLU
QPhCxaffCXujpV302wponlIlIYO4CnkqyaMTuBAKsaIeMjDjGewDy7xqJ3spihcn
qDNvzdfIMTxBby+E6hJRHnA4JrJH9mP21xEOp9QJ9vKdw79C1XaVAWgeYaJ55YKl
v1aFc7Ryn97LAKAeLcK/d2qA8y9dNUrTEin/MQs41blOKj0WA1eQ991ugjS49Mw=
=ypFd
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: A couple more updates for v4.2
These were sitting on my laptop.
There's a bunch of additional updates and fixes that came in since my
orignal pull request here, including DT support for rt5645 and fairly
large serieses of cleanups and improvements to tas2552 and rcar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVh9RgAAoJECTWi3JdVIfQZjYH/3t48LgdB5dxKxIhn70kiaUx
DqXCIkFOvkum1KUU3VTgcCZAT/dOEvbAY2S8PtxKbPRyRpmY1CqyXDEL7fXICl+y
kyDBhZYKdzVlf+LBb4TIOibaRONQqJNATRWFN8bJu0L9wzqo2jUjZSYqpJxuvnYD
U9T4P0dNbIN35ioVrK/0QPt6V2bCPs/qw3UwXmojl2T/4JDATdE+2yJO/SXzdEdR
qq5aRtS+Ak6yx5DpWw/QBkt85NrbuwyoeYRNQuRXCOAWC8SPmHB/H+aNsvMNAcP1
UZuRVtxPXjkFp6OVDJ4rIOg8hVb0cfXqUfnj+syEpZxtmRcS7Wwi1Y2M3BJMV1A=
=H6q+
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2-2' into asoc-next
ASoC: Further updates for v4.2
There's a bunch of additional updates and fixes that came in since my
orignal pull request here, including DT support for rt5645 and fairly
large serieses of cleanups and improvements to tas2552 and rcar.
# gpg: Signature made Mon 22 Jun 2015 10:24:48 BST using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVddV1AAoJECTWi3JdVIfQQQsH/RG3lgOeot5jLWMsxJSKChEl
KI+aaMcOw6Dj2LDccN8i6vUp8q44cKSXIc7lGLOzJW4K+OydCCGAvE+sJGyRE1dd
yOHwcbvjJi4zFlt01RZchJ/Wa/S6zFucl5N9HxWsV4bEtfAA59IuhJLtospUlwsA
mf9mpvSdeUAeh3lM2+AqAbXhTo6dYfD5ky5nrtpAkZjG8gqUG0u8Tpauja0lLcHi
72/3EkzKR6KHaefyPw3LdN+/H/YK79uHCVcctZnQg5xUUymcO16ReoTxKwV9cnDb
lBJ6wO8RpUAO9evoG2Yj/l4p+czDCm5VkHMq0nPklHVRh7s/2PwKfox1aw4Pumg=
=wolq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2' into asoc-next
ASoC: Updates for v4.2
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
# gpg: Signature made Mon 08 Jun 2015 18:48:37 BST using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
There's a bunch of additional updates and fixes that came in since my
orignal pull request here, including DT support for rt5645 and fairly
large serieses of cleanups and improvements to tas2552 and rcar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVh9RgAAoJECTWi3JdVIfQZjYH/3t48LgdB5dxKxIhn70kiaUx
DqXCIkFOvkum1KUU3VTgcCZAT/dOEvbAY2S8PtxKbPRyRpmY1CqyXDEL7fXICl+y
kyDBhZYKdzVlf+LBb4TIOibaRONQqJNATRWFN8bJu0L9wzqo2jUjZSYqpJxuvnYD
U9T4P0dNbIN35ioVrK/0QPt6V2bCPs/qw3UwXmojl2T/4JDATdE+2yJO/SXzdEdR
qq5aRtS+Ak6yx5DpWw/QBkt85NrbuwyoeYRNQuRXCOAWC8SPmHB/H+aNsvMNAcP1
UZuRVtxPXjkFp6OVDJ4rIOg8hVb0cfXqUfnj+syEpZxtmRcS7Wwi1Y2M3BJMV1A=
=H6q+
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Further updates for v4.2
There's a bunch of additional updates and fixes that came in since my
orignal pull request here, including DT support for rt5645 and fairly
large serieses of cleanups and improvements to tas2552 and rcar.
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVddV1AAoJECTWi3JdVIfQQQsH/RG3lgOeot5jLWMsxJSKChEl
KI+aaMcOw6Dj2LDccN8i6vUp8q44cKSXIc7lGLOzJW4K+OydCCGAvE+sJGyRE1dd
yOHwcbvjJi4zFlt01RZchJ/Wa/S6zFucl5N9HxWsV4bEtfAA59IuhJLtospUlwsA
mf9mpvSdeUAeh3lM2+AqAbXhTo6dYfD5ky5nrtpAkZjG8gqUG0u8Tpauja0lLcHi
72/3EkzKR6KHaefyPw3LdN+/H/YK79uHCVcctZnQg5xUUymcO16ReoTxKwV9cnDb
lBJ6wO8RpUAO9evoG2Yj/l4p+czDCm5VkHMq0nPklHVRh7s/2PwKfox1aw4Pumg=
=wolq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2' into asoc-next
ASoC: Updates for v4.2
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
# gpg: Signature made Mon 08 Jun 2015 18:48:37 BST using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
The rate controls are codec-specific, it's not possible to
generically say what the range or the meaning of each control
is (or even if they exist at all) - that depends on the
particular codec.
This is currently being handled for Arizona codecs by putting
an Arizona-specific table of controls inside the wm_adsp driver.
This creates a dependency between wm_adsp and arizona.c, and is an
awkward solution if the ADSP is used in another family of codecs
Fix this by moving the Arizona-specific rate controls into the
Arizona codec drivers.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix trivial typo.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A typical io ops use simple io accessors which can be common for most
drivers, so provide a default ops which will be used if driver doesn't
provide one
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In HDA extended bus the HDA link objects are created when multilink
capabilities are parsed. We need a routine which free up these link objects
for a bus. So add snd_hdac_link_free_all routine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDAC extended core should create streams for an extended bus and also free
up those on cleanup. So introduce snd_hdac_ext_stream_init_all and
snd_hdac_stream_free_all routines
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'047000278da3a17f8("ASoC: rsrc-card: cleanup for DPCM")'
cleanuped rsrc-card driver, but then, unused ret was left.
Below warning happen without this patch
${LINUX}/sound/soc/sh/rcar/rsrc-card.c: In function 'rsrc_card_startup':
${LINUX}/sound/soc/sh/rcar/rsrc-card.c:78:6: warning: unused variable \
'ret' [-Wunused-variable]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
