"IE set" TLV carries the same information as
qlink_event_scan_result::frame_type. Convert the event to make use of
TLV and drop frame_type member.
While at it, make qlink_event_scan_result structure alignement-safe.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Specifying frame type for "IE set" TLV will allow to use several
TLVs in a single message.
Modify users accordingly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Supported WiFi operation modes are now identified per-band based on
HT/VHT capabilities of each band.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Information on which HT/VHT capabilities can be overridden is reported
per-MAC by wireless device.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HT/VHT capabilities must be reported per each band supported by a radio,
not for all bands on a radio. Furthermore, driver better not assume
any capabilities and just use whetever is reported by device itself.
To support this, convert "get channels" command into "get band info"
command. Difference is that it may also carry HT/VHT capabilities along
with channels information.
While at it, also add "num_bitrates" field to "get band info" command,
for future use.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The configuration of the IEs for probe requests was done in a P2P
related function, which is not very obvious. Moving it to
.scan callback function, ie. brcmf_cfg80211_scan().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The field struct brcmf_cfg80211_info::active_scan is set to true upon
initializing the driver instance, but it is never changed so simply
get rid of it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function brcmf_cfg80211_escan() is only called by brcmf_cfg80211_scan()
so there is no reason to split in two function especially since the latter
does not do an awful lot.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Minor cleanup using provided macro to convert milliseconds interval
to jiffies in brcmf_cfg80211_escan().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function brcmf_cfg80211_escan() was always called with a non-null
request parameter and null pointer for this_ssid parameter. Clean up
the function removing the dead code path.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Disable arp and nd offload to allow all packets sending to host.
Reported-by: Phil Elwell <phil@raspberrypi.org>
Tested-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware uses a mailbox to communicate to the host what is going
on. In the driver we validate the bit received. Various people seen
the following message:
brcmfmac: brcmf_sdio_hostmail: Unknown mailbox data content: 0x40012
Bit 4 is cause of this message, but this actually indicates the firmware
has halted. Handle this bit by giving a more meaningful error message.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simple cases of overlapping changes in the packet scheduler.
Must easier to resolve this time.
Which probably means that I screwed it up somehow.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VLAN tag is present in the packet buffer (i.e VLAN stripping disabled, QinQ)
the driver will currently report CHECKSUM_UNNECESSARY.
Instead of using CHECKSUM_COMPLETE offload for packets with first
ethertype of IPv4/6, use it for packets with last ethertype of IPv4/6 to
cover the former cases as well.
The checksum field present in the CQE is calculated from the IP header
until the end of the packet. When the first ethertype is different than
IPv4/6 (for ex. 802.1Q VLAN) a checksum of the VLAN header/s should be
added. The small header/s checksum calculation will allow us to use
CHECKSUM_COMPLETE instead of CHECKSUM_UNNECESSARY.
Testing bandwidth of one and 8 TCP streams to a single RQ,
LRO and VLAN stripping offloads disabled:
CPU: Intel(R) Xeon(R) CPU E5-2660 v2 @ 2.20GHz
NIC: Mellanox Technologies MT27710 Family [ConnectX-4 Lx]
Before:
+--------------+--------------------+---------------------+----------------------+
| Traffic type | 1 Stream BW [Mbps] | 8 Streams BW [Mbps] | Checksum offload |
+--------------+--------------------+---------------------+----------------------+
| Untagged | 28,247.35 | 24,716.88 | CHECKSUM_COMPLETE |
| VLAN | 27,516.69 | 23,752.26 | CHECKSUM_UNNECESSARY |
| QinQ | 6,961.30 | 20,667.04 | CHECKSUM_UNNECESSARY |
+--------------+--------------------+---------------------+----------------------+
Now:
+--------------+--------------------+---------------------+-------------------+
| Traffic type | 1 Stream BW [Mbps] | 8 Streams BW [Mbps] | Checksum offload |
+--------------+--------------------+---------------------+-------------------+
| Untagged | 28,521.28 | 24,926.32 | CHECKSUM_COMPLETE |
| VLAN | 27,389.37 | 23,715.34 | CHECKSUM_COMPLETE |
| QinQ | 6,901.77 | 20,845.73 | CHECKSUM_COMPLETE |
+--------------+--------------------+---------------------+-------------------+
No performance degradation observed.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The following counters are now exposed through ethtool -S:
rx[i]_removed_vlan_packets (per channel)
rx_removed_vlan_packets
tx[i]_added_vlan_packets (per channel)
tx_added_vlan_packets
rx_removed_vlan_packets: The number of packets that had their
outer VLAN header stripped to the CQE by the hardware.
tx_added_vlan_packets: The number of packets that had their
outer VLAN header inserted by the hardware.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Report VLAN insertion support for S-tagged packets and add support by
choosing the correct VLAN type in the WQE.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When a user chooses to use 802.1ad VLAN the proper steering rules will
be added to the VLAN flow table (matching the specific S-tag VID).
Due to current hardware limitation, when using 802.1ad, we must disable
C-tag VLAN stripping on the RQs.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When add VLAN rule fails the active vlan bit should be cleared.
Fixes: afb736e933 ("net/mlx5: Ethernet resource handling files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Rename VLAN related symbols to better reflect the fact that they
are associated to C-tag VLAN.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This reverts commit baedf68a06.
There is an updated version of this fix which covers
the problem more thoroughly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable framelen is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/net/wireless/zydas/zd1201.c:234:3: warning: Value stored
to 'framelen' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The pointer dev is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/net/wireless/intersil/orinoco/orinoco_usb.c:1468:2: warning:
Value stored to 'dev' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer sta_priv is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/net/wireless/intel/iwlegacy/4965-rs.c:2163:2: warning: Value
stored to 'sta_priv' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
cfg_cmd is initialized to zero and this value is never read, instead
it is over-written in the start of a do-while loop. Remove the
redundant initialization. Cleans up clang warning:
drivers/net/wireless/realtek/rtlwifi/core.c:1750:22: warning: Value
stored to 'cfg_cmd' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
tid_data is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/net/wireless/realtek/rtlwifi/base.c:1581:2: warning: Value
stored to 'tid_data' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The calculation of ppsc->last_wakeup_time is not y2038-safe, but
the variable is not used at all, so we can simply drop it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
do_gettimeofday() is deprecated and slower than necessary for the purpose
of reading the seconds. This changes rtl_op_suspend/resume to use
ktime_get_real_seconds() instead, which is simpler and avoids confusion
about whether it is y2038-safe or not.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We set rtlhal->last_suspend_sec to an uninitialized stack variable,
but unfortunately gcc never warned about this, I only found it
while working on another patch. I opened a gcc bug for this.
Presumably the value of rtlhal->last_suspend_sec is not all that
important, but it does get used, so we probably want the
patch backported to stable kernels.
Cc: stable@vger.kernel.org
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82839
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
8822be checks H2CQ by int_d, so we extend to four ISR.
Also, irq_mask is extended to four.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the driver for the RTL8822BE is added, it will need an ID for
further use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the RTL8822BE, an H2C tx queue is added to download FW and special
data. This change implements the support code in rtl_pci.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The number of TX/RX BD desc for 8822BE is 512.
The TX/RX BD architecture of 8822BE is the same as 8192EE.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In several places, the code assigns a variable inside an "if" or "case"
block, but uses it only once. The code is simplified by eliminating
the extraneous variable. With this change, one level of indenting is
saved.
This patch does not cause any functional changes in the binary code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch.pl reports a number of formatting problems in this source
file. None of the changes cause any functional changes in the driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch.pl reports a number of formatting problems in this header
file. None of the changes cause any functional changes in the driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The bonding miimon logic has a flaw, in that a failure of the
rtnl_trylock can cause a slave to become permanently stuck in
BOND_LINK_FAIL state.
The sequence of events to cause this is as follows:
1) bond_miimon_inspect finds that a slave's link is down, and so
calls bond_propose_link_state, setting slave->new_link_state to
BOND_LINK_FAIL, then sets slave->new_link to BOND_LINK_DOWN and returns
non-zero.
2) In bond_mii_monitor, the rtnl_trylock fails, and the timer is
rescheduled. No change is committed.
3) bond_miimon_inspect is called again, but this time the slave
from step 1 has recovered. slave->new_link is reset to NOCHANGE, and, as
slave->link was never changed, the switch enters the BOND_LINK_UP case,
and does nothing. The pending BOND_LINK_FAIL state from step 1 remains
pending, as new_link_state is not reset.
4) The state from step 3 persists until another slave changes link
state and causes bond_miimon_inspect to return non-zero. At this point,
the BOND_LINK_FAIL state change on the slave from steps 1-3 is committed,
and the slave will remain stuck in BOND_LINK_FAIL state even though it
is actually link up.
The remedy for this is to initialize new_link_state on each entry
to bond_miimon_inspect, as is already done with new_link.
Fixes: fb9eb899a6 ("bonding: handle link transition from FAIL to UP correctly")
Reported-by: Alex Sidorenko <alexandre.sidorenko@hpe.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool statistics support by reading the GOP statistics from the
hardware counters. Also implement a workqueue to gather the statistics
every second or some 32-bit counters could overflow.
Suggested-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory allocation functions already display some informaton in case of
memory allocation failure. There is no need to add an extra 'dev_err' here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'of_phy_find_device()' fails, we must undo the previous 'of_node_get()'
call, as done the the following error handling code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to release explicitly some devm_ allocated resources.
If the 'mac_probe()' probe function fails, they will be released
automatically, as already done in the other error handling paths of
this function.
Also goto '_return_of_get_parent' as in the other error handling paths.
This is useless (priv->fixed_link is NULL at this point), but at least
it is consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c6e26ea8c8 ("dpaa_eth: change device used") has removed usage of
'dev_set_drvdata()' in the 'mac_probe() function.
This call should also be axed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting dev->hard_mtu to 0 will cause a divide error in
usbnet_probe. Protect against devices with bogus CDC Ethernet
functional descriptors by ignoring a zero wMaxSegmentSize.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ds->num_ports is 3, there is no need to check range of "port"
parameter.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit architectures, rtc_time_to_tm() returns incorrect results
in 2038 or later, and do_gettimeofday() is broken for the same reason.
This changes the code to use ktime_get_real_seconds() and time64_to_tm()
instead, both of them are 2038-safe, and we can also get rid of the
CONFIG_RTC_LIB dependency that way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We return on the previous line so this "return 0;" statement should just
be deleted.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove scripts/checkpatch.pl CHECKs by adjusting indenting.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove scripts/checkpatch.pl WARNING by replacing msleep(1) with usleep_range()
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the VID create error handling
case instead of 0, as done elsewhere in this function.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the dpaa_bp_alloc() error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ndo_setup_tc with enum tc_setup_type value of
TC_SETUP_QDISC_STATS. This call updates the generic qdisc stats from the
cache if the handle ID that is asked for matching the root qdisc ID and
fails otherwise.
Currently doesn't support qlen and rqueues.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ndo_setup_tc with enum tc_setup_type value of
TC_SETUP_RED_XSTATS. This call returns the RED qdisc xstats from the cache
if the handle ID that is asked for matching the root qdisc ID and fails
otherwise.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more statistics to be collected from the HW periodically. These stats
are tclass based (beside ECN marked packet, that exist only port based).
They are needed to expose RED qdisc stats and xstats correctly.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the counter group definitions for 2 new counter groups
which are necessary for gaining ECN & wred counters.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ndo_setup_tc with enum tc_setup_type value of TC_SETUP_RED.
This call sets RED qdisc on a traffic class.
This patch supports RED qdisc only as a root qdisc and set in on the
default tclass. It can be set with or without ECN.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds 2 new registers:
- Congestion WRED ECN TClass Profile Register [CWTP]
- Congestion WRED ECN TClass and Pool Mapping Register [CWTPM]
These registers would later be needed to offload RED-related
functionality to the HW.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change TC_SETUP_CBS to TC_SETUP_QDISC_CBS to match the new convention..
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new
convention.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 07f4c90062 ("tcp/dccp: try to not exhaust ip_local_port_range
in connect()"), we will try to use even ports for connect(). Then if an
application (seen clearly with iperf) opens multiple streams to the same
destination IP and port, each stream will be given an even source port.
So the bonding driver's simple xmit_hash_policy based on layer3+4 addressing
will always hash all these streams to the same interface. And the total
throughput will limited to a single slave.
Change the tcp code will impact the whole tcp behavior, only for bonding
usage. Paolo Abeni suggested fix this by changing the bonding code only,
which should be more reasonable, and less impact.
Fix this by discarding the lowest hash bit because it contains little entropy.
After the fix we can re-balance between slaves.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hn is being kfree'd in mlx5e_del_l2_from_hash and then dereferenced
by accessing hn->ai.addr
Fix this by copying the MAC address into a local variable for its safe use
in all possible execution paths within function mlx5e_execute_l2_action.
Addresses-Coverity-ID: 1417789
Fixes: eeb66cdb68 ("net/mlx5: Separate between E-Switch and MPFS")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is better for code locality and should slightly
speed up normal interrupts.
This also allows PPS clock output to start working for
i.mx7. This is because i.mx7 was already using the limit
of 3 interrupts, and needed another.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2 driver can't cope at all with the TX affinities being
changed from userspace, and spit an endless stream of
[ 91.779920] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.779930] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780402] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780406] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780415] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780418] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
rendering the box completely useless (I've measured around 600k
interrupts/s on a 8040 box) once irqbalance kicks in and start
doing its job.
Obviously, the driver was never designed with this in mind. So let's
work around the problem by preventing userspace from interacting
with these interrupts altogether.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hyper-V hosts are known to send RNDIS messages even after we halt the
device in rndis_filter_halt_device(). Remove user visible messages
as they are not really useful.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was found that in some cases host refuses to teardown GPADL for send/
receive buffers (probably when some work with these buffere is scheduled or
ongoing). Change the teardown logic to be:
1) Send NVSP_MSG1_TYPE_REVOKE_* messages
2) Close the channel
3) Teardown GPADLs.
This seems to work reliably.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we create a LED trigger for any link speed known to a PHY.
These triggers only fire when their exact link speed had been negotiated
(they aren't cumulative, that is, they don't fire for "their or any higher"
link speed).
What we are missing, however, is a trigger which will fire on any link
speed known to the PHY. Such trigger can then be used for implementing a
poor man's substitute of the "link" LED on boards that lack it.
Let's add it.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, phy_led_trigger_change_speed() is handling a "no link" condition
like it was some kind of an error (using "goto" to a code at the function
end).
However, having no link at PHY is an ordinary operational state, so let's
handle it in an appropriately named separate function so it is more obvious
what the code is doing.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having the function name hard-coded (it might change and we
forgot to update them in the debug output) we can use __func__ instead
and also shorter the line so we do not need to break it.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Harry Morris <h.morris@cascoda.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Remove unneeded parentheses and fix format for pointer style.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Harry Morris <h.morris@cascoda.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Bring it in line with the rest of the ieee802154 drivers.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
It seems that this is a copy/paste error and the proper bit masking is:
BIT_TXNIE | BIT_RXIE
This issue was detected with the help of Coccinelle.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Fixes: 7d840545e5 ("mrf24j40: replace magic numbers")
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
The check is valid but it does not warrant to crash the kernel. A
WARN_ON() is good enough here.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Instead of having the function name hard-coded (it might change and we
forgot to update them in the debug output) we can use __func__ instead
and also shorter the line so we do not need to break it.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Fix some spacing and needed new line.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
The check is valid but it does not warrant to crash the kernel. A
WARN_ON() is good enough here.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Instead of having the function name hard-coded (it might change and we
forgot to update them in the debug output) we can use __func__ instead
and also shorter the line so we do not need to break it.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
* Some new PCI IDs;
* A bunch of cleanups;
* The timers update by Kees;
* Add more register dump call-sites;
* A fix for a locking issue in the TX flush code;
* Actual implementation of the TX flush code for A000;
* An optimization to drop RX frames during restart to avoid BA issues;
-----BEGIN PGP SIGNATURE-----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=CC8e
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
iwlwifi updates
* Some new PCI IDs;
* A bunch of cleanups;
* The timers update by Kees;
* Add more register dump call-sites;
* A fix for a locking issue in the TX flush code;
* Actual implementation of the TX flush code for A000;
* An optimization to drop RX frames during restart to avoid BA issues;
Saeed Mahameed says:
====================
mlx5-updates-2017-11-04
This series includes:
From Huy: dscp to priority mapping for Ethernet packet.
===================================================
First six patches enable differentiated services code point (dscp) to
priority mapping for Ethernet packet. Once this feature is
enabled, the packet is routed to the corresponding priority based on its
dscp. User can combine this feature with priority flow control (pfc)
feature to have priority flow control based on the dscp.
Firmware interface:
Mellanox firmware provides two control knobs for this feature:
QPTS register allow changing the trust state between dscp and
pcp mode. The default is pcp mode. Once in dscp mode, firmware will
route the packet based on its dscp value if the dscp field exists.
QPDPM register allow mapping a specific dscp (0 to 63) to a
specific priority (0 to 7). By default, all the dscps are mapped to
priority zero.
Software interface:
This feature is controlled via application priority TLV. IEEE
specification P802.1Qcd/D2.1 defines priority selector id 5 for
application priority TLV. This APP TLV selector defines DSCP to priority
map. This APP TLV can be sent by the switch or can be set locally using
software such as lldptool. In mlx5 drivers, we add the support for net
dcb's getapp and setapp call back. Mlx5 driver only handles the selector
id 5 application entry (dscp application priority application entry).
If user sends multiple dscp to priority APP TLV entries on the same
dscp, the last sent one will take effect. All the previous sent will be
deleted.
The firmware trust state (in QPTS register) is changed based on the
number of dscp to priority application entries. When the first dscp to
priority application entry is added by the user, the trust state is
changed to dscp. When the last dscp to priority application entry is
deleted by the user, the trust state is changed to pcp.
When the port is in DSCP trust state, the transmit queue is selected
based on the dscp of the skb.
When the port is in DSCP trust state and vport inline mode is not NONE,
firmware requires mlx5 driver to copy the IP header to the
wqe ethernet segment inline header if the skb has it.
This is done by changing the transmit queue sq's min inline mode to L3.
Note that the min inline mode of sqs that belong to other features
such as xdpsq, icosq are not modified.
===================================================
Plus to the dscp series, some small misc changes are include as well:
From Inbar, Ethtool msglvl support and some debug prints in DCBNL logic
From Or Gerlitz, Enlarge the NIC TC offload table size
From Rabie, Initialize destination_flow struct to 0
From Feras, Add inner TTC table to IPoIB flow steering
From Tal, Enable CQE based moderation on TX CQ
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in the driver ethtool ops to modify the NFP FEC modes.
The FEC modes can be set for vNIC associated with physical ports or
for MAC representor netdevs.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement helpers to determine and modify FEC modes via the NSP.
The NSP advertises FEC capabilities on a per port basis and provides
support for:
* Auto mode selection
* Reed Solomon
* BaseR
* None/Off
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it is now safe to modify link settings for representors, we can
attach the get/set link settings ndos to it. The get/set link settings
are nfp_port based operations.
If a port becomes invalid, the representor will be removed in the same
way a vnic would be.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NSP port table has been refreshed, resync the representor state
with the new port information. At the moment, this only entails looking
for invalid ports and killing off representors associated with them.
The repr instance becomes NULL which is safe since the app accessor
function for reprs returns NULL when it cannot access a repr.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The criteria that reprs cannot be replaced with another new set of reprs
has been removed. This check is not needed since the only use case that
could exercise this at the moment, would be to modify the number of
SRIOV VFs without first disabling them. This case is explicitly
disallowed in any case and subsequent patches in this series
need to be able to replace the running set of reprs.
All cases where the return code used to be checked for the
nfp_app_reprs_set function have been removed.
As stated above, it is not possible for the current code to encounter a
case where reprs exist and need to be replaced.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent management FW images can perform full reinit of MAC cores
without requiring a reboot. When loading the driver check if there
are changes pending and if so call NSP MAC reinit. Full application
FW reload is still required, and all MACs need to be reinited at the
same time (not only the ones which have been reconfigured, and thus
potentially causing disruption to unrelated netdevs) therefore for
now changing MAC config without reloading the driver still remains
future work.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthias reports:
nfp_eth_set_bit_config() is marked as __always_inline to allow gcc to
identify the 'mask' parameter as known to be constant at compile time,
which is required to use the FIELD_GET() macro.
The forced inlining does the trick for gcc, but for kernel builds with
clang it results in undefined symbols:
drivers/net/ethernet/netronome/nfp/nfpcore/nfp_nsp_eth.o: In function
`__nfp_eth_set_aneg':
drivers/net/ethernet/netronome/nfp/nfpcore/nfp_nsp_eth.c:(.text+0x787):
undefined reference to `__compiletime_assert_492'
drivers/net/ethernet/netronome/nfp/nfpcore/nfp_nsp_eth.c:(.text+0x7b1):
undefined reference to `__compiletime_assert_496'
These __compiletime_assert_xyx() calls would have been optimized away
if
the compiler had seen 'mask' as a constant.
Add a macro to extract the mask and shift and pass those to
nfp_eth_set_bit_config() separately.
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev->rx_dropped was including packets dropped by napi_gro_receive.
If a packet is dropped by network stack, it should not be counted under
driver Rx dropped.
Made necessary changes to not include network stack drops under
netdev->rx_dropped.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following steps are taken in the driver to offload an XDP program:
XDP_SETUP_PROG:
* prepare:
- allocate program state;
- run verifier (bpf_analyzer());
- run translation;
* load:
- stop old program if needed;
- load program;
- enable BPF if not enabled;
* clean up:
- free program image.
With new infrastructure the flow will look like this:
BPF_OFFLOAD_VERIFIER_PREP:
- allocate program state;
BPF_OFFLOAD_TRANSLATE:
- run translation;
XDP_SETUP_PROG:
- stop old program if needed;
- load program;
- enable BPF if not enabled;
BPF_OFFLOAD_DESTROY:
- free program image.
Take advantage of the new infrastructure. Allocation of driver
metadata has to be moved from jit.c to offload.c since it's now
done at a different stage. Since there is no separate driver
private data for verification step, move temporary nfp_meta
pointer into nfp_prog. We will now use user space context
offsets.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct nfp_prog is currently only used internally by the translator.
This means there is a lot of parameter passing going on, between
the translator and different stages of offload. Simplify things
by allocating nfp_prog in offload.c already.
We will now use kmalloc() to allocate the program area and only
DMA map it for the time of loading (instead of allocating DMA
coherent memory upfront).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of offload/translation prepare logic will be moved to
offload.c. To help git generate more reasonable diffs
move nfp_prog_prepare() and nfp_prog_free() functions
there as a first step.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware supports live replacement of programs for quite some
time now. Remove the software-fallback related logic and
depend on the FW for program replace. Seamless reload will
become a requirement if maps are present, anyway.
Load and start stages have to be split now, since replace
only needs a load, start has already been done on add.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently create a fake cls_bpf offload object when we want
to offload XDP. Simplify and clarify the code by moving the
TC/XDP specific logic out of common offload code. This is easy
now that we don't support legacy TC actions. We only need the
bpf program and state of the skip_sw flag.
Temporarily set @code to NULL in nfp_net_bpf_offload(), compilers
seem to have trouble recognizing it's always initialized. Next
patches will eliminate that variable.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF offload's main header does not need to include nfp_net.h.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register renumbering was removed and will not be coming back
in its old, naive form, given that it would be fundamentally
incompatible with calling functions. Remove the leftovers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only support BPF_PROG_TYPE_SCHED_CLS programs in direct
action mode. This simplifies preparing the offload since
there will now be only one mode of operation for that type
of program. We need to know the attachment mode type of
cls_bpf programs, because exit codes are interpreted
differently for legacy vs DA mode.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_xdp is a control path callback for setting up XDP in the
driver. We can reuse it for other forms of communication
between the eBPF stack and the drivers. Rename the callback
and associated structures and definitions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114893
Addresses-Coverity-ID: 114894
Addresses-Coverity-ID: 114895
Addresses-Coverity-ID: 114896
Addresses-Coverity-ID: 114897
Addresses-Coverity-ID: 114898
Addresses-Coverity-ID: 114899
Addresses-Coverity-ID: 114900
Addresses-Coverity-ID: 114901
Addresses-Coverity-ID: 114902
Addresses-Coverity-ID: 114903
Addresses-Coverity-ID: 114904
Addresses-Coverity-ID: 114905
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can now build this driver on ARM, so I ran into a randconfig build
warning that presumably had existed on powerpc already.
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c: In function 'sg_fd_to_skb':
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:1712:18: error: 'skb' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I'm slightly changing the logic here, to make it obvious to the
compiler that 'skb' is always initialized.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using CQE based moderation on TX CQ we can reduce the number of TX
interrupt rate. Besides the benefit of less interrupts, this also
allows the kernel to better utilize TSO. Since TSO has some CPU overhead,
it might not aggregate when CPU is under high stress. By reducing the
interrupt rate and the CPU utilization, we can get better aggregation
and better overall throughput.
The feature is enabled by default and has a private flag in ethtool
for control.
Throughput, interrupt rate and TSO utilization improvements:
(ConnectX-4Lx 40GbE, unidirectional, 1/16 TCP streams, 64B packets)
---------------------------------------------------------
Metric | Streams | CQE Based | EQE Based | improvement
---------------------------------------------------------
BW | 1 | 2.4Gb/s | 2.15Gb/s | +11.6%
IR | 1 | 27Kips | 50.6Kips | -46.7%
TSO Util | 1 | 74.6% | 71% | +5%
BW | 16 | 29Gb/s | 25.85Gb/s | +12.2%
IR | 16 | 482Kips | 745Kips | -35.3%
TSO Util | 16 | 69.1% | 49% | +41.1%
*BW = Bandwidth, IR = Interrupt rate, ips = interrupt per second.
TSO Util = bytes in TSO sessions / all bytes transferred
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This is needed in order to enlarge it with more members that will get
value of 0 when not set.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The NIC TC offload table size was hard coded to 1k. Change it to be
min(max NIC RX table size,
min(max flow counters, 64k) * num flow groups)
where the max values are read from the firmware and the number of
flow groups is hard-coded as before this change.
We don't know upfront the division of flows to groups (== different masks).
This setup allows each group to be of size up to the where we want to go
(when supported, all offloaded flows use counters). Thus, we don't expect
multiple occurences for a group which in turn would add steering hops.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add debug print when changing the configuration of QoS through dcbnl.
Use ethtool -s <devname> msglvl hw on/off to toggle debug messages.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Reviewed-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If the port is in DSCP trust state, packets are placed in the right
priority queue based on the dscp value. This is done by selecting
the transmit queue based on the dscp of the skb.
Until now select_queue honors priority only from the vlan header.
However that is not sufficient in cases where port trust state is DSCP
mode as packet might not even contain vlan header. Therefore if the port
is in dscp trust state and vport's min inline mode is not NONE,
copy the IP header to the eseg's inline header if the skb has it.
This is done by changing the transmit queue sq's min inline mode to L3.
Note that the min inline mode of sqs that belong to other features such
as xdpsq, icosq are not modified.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch implements dcbnl hooks to set and delete DSCP to priority map
as defined by the DCB subsystem. Device maintains internal trust state
which needs to be set to DSCP state for performing DSCP to priority mapping.
When the first dscp to priority APP entry is added by the user, the
trust state is changed to dscp.
When the last dscp to priority APP entry is deleted by the user, the
trust state is changed to pcp.
If user sends multiple dscp to priority APP entries on the same dscp,
the last sent one will take effect. All the previous sent will be
deleted.
The dscp to priority APP entries are added and deleted in the net/dcb
APP database using dcb_ieee_setapp/getapp.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The QPTS register allows changing the priority trust state between pcp and
dscp. Add support to get/set trust state from device. When the port is
in pcp/dscp trust state, packet is routed by hardware to matching priority
based on its pcp/dscp value respectively.
The QPDPM register allow channing the dscp to priority mapping. Add support
to get/set dscp to priority mapping from device.
Note that to change a dscp mapping, the "e" bit of this dscp structure
must be set in the QPDPM firmware command.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The QCAM register provides capability bit for all the QoS registers
using ACCESS_REG command.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Change t4fw_version.h to update latest firmware version
number to 1.16.63.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/phy/phylink.c:570:6: warning:
symbol 'phylink_phy_change' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ/HSCAAoJEG4XJFUm622b2sQH+wXgE1swS9xp1AfV3hcVLGoJ
YjLjR3/BAxsIqkYwhswarTDrD3jsOKrL4ywRk+0BAdR7f2BeOYhQXtZqgjvE8cbu
WWv5LmSwuKM6tF3ujgjQ6yZvgyDHl2d7lZL59EWG05K/yjJuU8ByoUhLKM5IiqPh
SWXj3ZtydgGZm2eZTPyan+MFz91jw/X23Jm/AaIAxayf+1J4n1lNpc4rRhUxh/oy
kGLQ2vsVnegSiHJWTboDFPeRha+daBsbf1MQc0Bh7MzDoWcaqSNX5VgrbaRqp35u
sb9pmPZS4FzvAdU3bJ9AIPa9ujjblEvDp1JIhrfBUqiuTdvXDZ7XtW8kVsJk1RY=
=MvWY
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.15
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Return success if the same dispatch function is being registered for
a given opcode and subcode, there by allow multiple switchdev enable
and disables.
Signed-off-by: Vijaya Mohan Guvva <vijaya.guvva@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bound device of a tunnel device is down, encapsulated packets
are not egressed anymore, but tunnel decap still works. Extend
mlxsw_sp_nexthop_rif_update() to take IFF_UP into consideration when
deciding whether a given next hop should be offloaded.
Because the new logic was added to mlxsw_sp_nexthop_rif_update(), this
fixes the case where a newly-added tunnel has a down bound device, which
would previously be fully offloaded. Now the down state of the bound
device is noted and next hops forwarding to such tunnel are not
offloaded.
In addition to that, notice NETDEV_UP and NETDEV_DOWN of a bound device
to force refresh of tunnel encap route offloads.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bound device of an IP-in-IP tunnel changes, such as through
'ip tunnel change name $name dev $dev', the loopback backing the tunnel
needs to be recreated.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to L3 tunnel netdevices (through `ip tunnel change' as well as
`ip link set') lead to NETDEV_CHANGE being generated on the tunnel
device. Because what is relevant for the tunnel in question depends on
the tunnel type, handling of the event is dispatched to the IPIP module
through a newly-added interface mlxsw_sp_ipip_ops.ol_netdev_change().
IPIP tunnels now remember the last set of tunnel parameters in struct
mlxsw_sp_ipip_entry.parms, and use it to figure out what exactly has
changed.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bound device of a tunnel netdevice changes VRF, the loopback RIF
that backs the tunnel needs to be updated and existing encapsulating
routes need to be refreshed.
Note that several tunnels can share the same bound device, in which case
all the impacted tunnels need to be updated.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The approach for offloading IP tunnels implemented currently by mlxsw
doesn't allow two tunnels that have the same local IP address in the
same (underlay) VRF. Previously, offloads were introduced on demand as
encap routes were formed. When such a route was created that would cause
offload of a conflicting tunnel, mlxsw_sp_ipip_entry_create() would
detect it and return -EEXIST, which would propagate up and cause FIB
abort.
Now however IPIP entries are created as soon as an offloadable netdevice
is created, and the failure prevents creation of such device.
Furthermore, if the driver is installed at the point where such
conflicting tunnels exist, the failure actually prevents successful
modprobe.
Furthermore, follow-up patches implement handling of NETDEV_CHANGE due
to the local address change. However, NETDEV_CHANGE can't be vetoed. The
failure merely means that the offloads weren't updated, but the change
in Linux configuration is not rolled back. It is thus desirable to have
a robust way of handling these conflicts, which can later be reused for
handling NETDEV_CHANGE as well.
To fix this, when a conflicting tunnel is created, instead of failing,
simply pull the old tunnel to slow path and reject offloading the
new one.
Introduce two functions: mlxsw_sp_ipip_entry_demote_tunnel() and
mlxsw_sp_ipip_demote_tunnel_by_saddr() to handle this. Make them both
public, because they will be useful later on in this patchset.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to determine whether there are other offloaded tunnels with
the same local address, mlxsw_sp_ipip_entry_create() should look for a
tunnel with matching UL protocol, matching saddr, in the same VRF.
However instead of taking into account the UL protocol of the tunnel
netdevice (which mlxsw_sp_ipip_entry_saddr_matches() then compares to
the UL protocol of inspected IPIP entry), it deduces the UL protocol
from the inspected IPIP entry (and that's compared to itself).
This is currently immaterial, because only one tunnel type is offloaded,
and therefore the UL protocol always matches, but introducing support
for a tunnel with IPv6 underlay would uncover this error.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The work that needs to be done to update HW configuration in response to
changes is similar to what __mlxsw_sp_ipip_entry_update_tunnel() already
does, but with a number of twists: each change requires a different
subset of things to happen. Extend the function to support all these
uses, and allow finely-grained configuration of what should happen at
each call through a suite of function arguments.
Publish the updated function to allow use from the spectrum_ipip module.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The work that's done by mlxsw_sp_netdevice_ipip_ol_vrf_event() is a good
basis for a more versatile function that would take care of all sorts of
tunnel updates requests: __mlxsw_sp_ipip_entry_update_tunnel(). Extract
that function. Factor out a helper mlxsw_sp_ipip_entry_ol_lb_update() as
well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_rif_create() takes an extack parameter. So far,
for creation of loopback interfaces, NULL was passed. For some events
however the extack can be extracted and passed along. So do that for
NETDEV_CHANGEUPPER handler.
Use the opportunity to update the type of info argument that
mlxsw_sp_netdevice_ipip_ol_event() takes. Follow-up patches will
introduce handling of more changes, and some of them carry an extack as
well, but in an info structure of a different type. Though not strictly
erroneous (the pointer could be cast whichever way), it makes no sense
to pretend the value is always of a certain type, when in fact it isn't.
So change the prototype of the above-mentioned function as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The piece of logic to promote decap route, if any, is useful for generic
tunnel updates, not just for handling of NETDEV_UP events on tunnel
interfaces. Extract it to a separate function.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function only ever returns 0, so don't pretend it returns anything
useful and just make it void.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To implement NETDEV_CHANGE notifications on IP-in-IP tunnels, the
handler needs to figure out what actually changed, to understand how
exactly to update the offloads. It will do so by storing struct
ip_tunnel_parm with previous configuration, and comparing that to the
new version.
To facilitate these comparisons, extract the code that operates on
struct ip_tunnel_parm from the existing accessor functions, and make
those a thin wrapper that extracts tunnel parameters and dispatches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions ideologically belong to the IPIP module, and some
follow-up work will benefit from their presence there.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the code down the road needs this logic as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To distinguish between events related to tunnel device itself and its
bound device, rename a number of functions related to handling tunneling
netdevice events to include _ol_ (for "overlay") in the name. That
leaves room in the namespace for underlay-related functions, which would
have _ul_ in the name.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Hopefully this is the last batch of networking fixes for 4.14
Fingers crossed...
1) Fix stmmac to use the proper sized OF property read, from Bhadram
Varka.
2) Fix use after free in net scheduler tc action code, from Cong
Wang.
3) Fix SKB control block mangling in tcp_make_synack().
4) Use proper locking in fib_dump_info(), from Florian Westphal.
5) Fix IPG encodings in systemport driver, from Florian Fainelli.
6) Fix division by zero in NV TCP congestion control module, from
Konstantin Khlebnikov.
7) Fix use after free in nf_reject_ipv4, from Tejaswi Tanikella"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: systemport: Correct IPG length settings
tcp: do not mangle skb->cb[] in tcp_make_synack()
fib: fib_dump_info can no longer use __in_dev_get_rtnl
stmmac: use of_property_read_u32 instead of read_u8
net_sched: hold netns refcnt for each action
net_sched: acquire RTNL in tc_action_net_exit()
net: vrf: correct FRA_L3MDEV encode type
tcp_nv: fix division by zero in tcpnv_acked()
netfilter: nf_reject_ipv4: Fix use-after-free in send_reset
netfilter: nft_set_hash: disable fast_ops for 2-len keys
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZ0WQ6AAoJEHm+PkMAQRiGuloH/3sF4qfBhPuJo8OTf0uCtQ18
4Ux9zZbm81df/Jjz0exAp1Jqk+TvdIS3OXPWcKilvbUBP16hQcsxFTnI/5QF+YcN
87aNr+OCMJzOBK4suN1yhzO46NYHeIizdB0PTZVL1Zsto69Tt31D8VJmgH6oBxAw
Isb/nAkOr31dZ9PI5UEExTIanUt6EywVb0UswA+2rNl3h1UkeasQCpMpK2n6HBhU
kVD7sxEd/CN0MmfhB0HrySSam/BeSpOtzoU9bemOwrU2uu9+5+2rqMe7Gsdj4nX6
3Kk+7FQNktlrhxCZIFN/+CdusOUuDd8r/75d7DnsRK5YvSb0sZzJkfD3Nba68Ms=
=7J2+
-----END PGP SIGNATURE-----
Merge git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux
Merge 4.14-rc3 in order to pick up the new timer_setup function.
Allow chcr to do DMA mapping/Unmapping instead of lld cxgb4.
It moves "Copy AAD to dst buffer" requirement from driver to
firmware.
Signed-off-by: Harsh Jain <harsh@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes a bug for phy supported feature initialization.
Currently, the value of phydev->supported is initialized by kernel.
So it includes many features that we do not support, such as
SUPPORTED_FIBRE and SUPPORTED_BNC. This patch fixes it.
Fixes: 256727d (net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds nway_reset support for ethtool cmd.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds set_link_ksettings support for ethtool cmd.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of link_modes.advertising and the value of link_modes.supported
is initialized to zero every time in for loop in hns3_driv_to_eth_caps().
But we just want to set specified bit for them. Initialization is
unnecessary. This patch fixes it.
Fixes: 496d03e (net: hns3: Add Ethtool support to HNS3 driver)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug for ethtool's get_link_ksettings().
The advertising for autoneg is always added to advertised_caps
whether autoneg is enable or disable. This patch fixes it.
Fixes: 496d03e (net: hns3: Add Ethtool support to HNS3 driver)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug for ethtool's get_link_ksettings().
When phy exists, we should get autoneg from phy rather than from mac.
Because the value of mac.autoneg is invalid when phy exists.
Fixes: 496d03e (net: hns3: Add Ethtool support to HNS3 driver)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent IRQ coalescing clean up has removed a guard-rail for the max DMA
buffer coalescing value. This is a 6-bit value and must not be 0. We
already have a check for 0 but 64 is equivalent to 0 and will cause
non-stop interrupts. Fix it by adding the proper check.
Fixes: f8503969d2 ("bnxt_en: Refactor and simplify coalescing code.")
Reported-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent refactoring of coalesce settings contained a typo that prevents
receive settings from being set properly.
Fixes: 18775aa8a9 ("bnxt_en: Reorganize the coalescing parameters.")
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of a hardware restart the BA session data in HW is lost
so the reorder buffer simply passes the frames to mac80211 as is
as there is no NSSN set. Instead, we will drop these frames
before they reach the reorder buffer. mac80211 drops such frames anyway,
but we shouldn't rely on that. In addition it saves some
processing time
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
The RCU lifetime on baid_data is unclear, so this adds a direct copy of the
rcu_ptr passed to the original callback. It may be possible to improve this
to just use baid_data->mvm->baid_map[baid_data->baid] instead.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Sara Sharon <sara.sharon@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_mvm_flush_tx_path() function sends a synchronous command to
the firmware. When doing that, we must hold the mutex. The
iwl_mvm_flush_no_vif() function was mistakenly not holding the mutex.
Fix it.
Fixes: 6110d9e5bd ("iwlwifi: mvm: Flush non STA TX queues")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the mac flush flow, we should flush all existing queues.
Since FW API for a000 devices is flush per RA-TID, simply
flush all stations with all tids.
From FW perspective, asking to flush a TID that doesn't have
a queue is valid, so we can just set all bits in the TID mask.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function is very indented and hard to read.
Refactor it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we return early from sync_rx_queues for a000 devices.
This may cause, in case of a non-empty reorder buffer, a warning
later on since the RX queue isn't getting the notification to
empty it.
A better approach would be to send the notification for the default
queue only.
Do this hard coded for now, until we will have the API to enable
multi queue for a000 devices.
Fixes: bc02946964 ("iwlwifi: mvm: disable RX queue notification for a000 devices")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Commit a6d24fad00 ("iwlwifi: pcie: dump registers when HW becomes
inaccessible") added a function to dump pcie config registers and
memory mapped registers on a failure. It is currently only accessible
within trans.c. Add it to struct iwl_trans_ops, so that failure cases
in other files can call it. While there, add a call to this function
from iwl_pcie_load_firmware_chunk in pcie/tx.c, since this is a common
failure case seen on some platforms.
Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org>
[modified the commit message slightly]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This was used for internal devices that are now deprecated.
All the currently existing devices can do paging without
any help from the host.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We had a bunch of code that was relevant for internal
devices only. Those devices are now being depreceated.
Kill all the now unneeded code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When there is a reorder timeout, we may get to a situation
where we have the timeout latency for all the next 64 frames.
This happens since NSSN is behind for a while, and the driver
won't release the frames, since it is not allowed by NSSN.
As a result the frame is stored in the reorder buffer although
there is no hole, and released 100 ms later.
Add a direct comparison to the reorder buffer head, and release
immediately if possible.
For example:
Frame 0 is missed. We receive frame 1, and store it in the buffer.
After 100 ms, frame 1 is released and reorder buffer head is 2.
We then receive frame 2, with NSSN 0, and store it instead of
releasing it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't plan to have products with 3 antennas in the near
future. All the rest of the code follows the same
assumption as well.
Remove the support for antenna C from rs_toggle_ant.
When trying to toggle from ANT_B, this avoids to go through
ANT_C, discover that it doesn't exist and continue to ANT_A.
In MIMO, this avoids to do ANT_AB -> ANT_BC -> ANT_AC and
back to ANT_AB.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After a FW reset on A000 NICs, the driver doesn't
set the seq number when re-allocating the queues.
This in turn leads to a mismatch between the seq
number the driver thinks each frame has, and the
actual seq num given by the HW.
This especially causes issues with aggregations,
since the driver could be waiting to start an
aggregation and queue traffic from the mac80211
until then, when actually it shouldn't be waiting.
Fixes: 310181ec34 ("iwlwifi: move to TVQM mode")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the code is mixing defines and is inconsistent.
When enabling a queue, we usually configure the scheduler
with IWL_FRAME_LIMIT - 64.
When sending to firmware the rate scaling, we limit aggregation
to LINK_QUAL_AGG_FRAME_LIMIT_DEF - 63, due to a scheduler bug.
Given that, clean up the following:
- Fix a stray queue enablement with LINK_QUAL_AGG_FRAME_LIMIT_DEF.
- Change the comparison that tests if queue needs to be reconfigured
to be compared directly to how it was configured.
This also saves the redundant round down of the buffer size just
for the sake of comparing it, making the code more readable.
- Better document gen2 logic
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is a macro for converting TX response rate to a
rate scale value, use it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support to new ethtool operation get_fecparam to
fetch FEC parameters.
Original Work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the device and the kernel are performing the multipath hash
according to the same parameters by updating the device whenever the
relevant netevent is generated.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we used the hardware's defaults for multipath hash
computation. This patch aligns the hardware's multipath parameters with
the kernel's.
For IPv4 packets, the parameters are determined according to the
'fib_multipath_hash_policy' sysctl during module initialization. In case
L3-mode is requested, only the source and destination IP addresses are
used. There is no special handling of ICMP error packets.
In case L4-mode is requested, a 5-tuple is used: source and destination
IP addresses, source and destination ports and IP protocol. Note that
the layer 4 fields are not considered for fragmented packets.
For IPv6 packets, the source and destination IP addresses are used, as
well as the flow label and the next header fields.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RECRv2 register is used for setting up the router's ECMP hash
configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct containing the work item queued from the netevent handler is
named after the only event it is currently used for, which is neighbour
updates.
Use a more appropriate name for the struct, as we are going to use it
for more events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to need to respond to netevents notifying us about
multipath hash updates by configuring the device's hash parameters.
Embed the netevent notifier in the router struct so that we could
retrieve it upon notifications and use it to configure the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a documentation mistake, the IPG length was set to 0x12 while it
should have been 12 (decimal). This would affect short packet (64B
typically) performance since the IPG was bigger than necessary.
Fixes: 44a4524c54 ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from thecxgb4_alloc_atid()
error handling case instead of 0.
Fixes: 12b276fbf6 ("cxgb4: add support to create hash filters")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-By: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Numbers in DT are stored in “cells” which are 32-bits
in size. of_property_read_u8 does not work properly
because of endianness problem.
This causes it to always return 0 with little-endian
architectures.
Fix it by using of_property_read_u32() OF API.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some wowlan related code was outside CONFIG_PM flag which caused these
build errors. They are fixed by moving that code under CONFIG_PM flag.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: ef71ed0608c ("rsi: sdio: Add WOWLAN support for S5 shutdown state")
Fixes: a24e35fcee0 ("rsi: sdio: Add WOWLAN support for S4 hibernate state")
Fixes: e1ced6422a3 ("rsi: sdio: add WOWLAN support for S3 suspend state")
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is generic. It doesn't contain wowlan specific code.
It should not be under CONFIG_PM. This patch resolves compilation
errors observed when CONFIG_PM flag is disabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: ef71ed0608c ("rsi: sdio: Add WOWLAN support for S5 shutdown state")
Fixes: a24e35fcee0 ("rsi: sdio: Add WOWLAN support for S4 hibernate state")
Fixes: e1ced6422a3 ("rsi: sdio: add WOWLAN support for S3 suspend state")
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
All member of Struct hdev->hw_stats is initialized to 0 as hdev is
allocated by devm_kzalloc. But in reset process, hdev will not be
allocated again, so need clear hdev->hw_stats in reset process, otherwise
the statistic will be wrong after reset. This patch set all of the
statistic counters to zero after reset.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we should use free_irq to free the nic irq during the unloading time.
because we use request_irq to apply it when nic up. It will crash if
up net device after reset the port. This patch fixes the issue.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implement the interface of reset notification in hns3_enet,
it will do resetting business which include shutdown nic device,
free and initialize client side resource.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add timeout handler in hns3_enet.c to handle
TX side timeout event, when TX timeout event occur, it will triger
NIC driver into reset process.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds reset support for PF,it include : global reset, core reset,
IMP reset, PF reset.The core reset will Reset all datapath of all functions
except IMP, MAC and PCI interface. Global reset is equal with the core
reset plus all MAC reset. IMP reset is caused by watchdog timer expiration,
the same with core reset in the reset flow. PF reset will reset whole
physical function.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds initialization and deinitialization for misc interrupt.
This interrupt will be used to handle reset message(IRQ).
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no necessary to reallocate the descriptor and remap the descriptor
memory in reset process, But there is still some other action exist in both
reset process and initialization process.
To reuse the common interface in reset process and initialization process,
This patch moves out the descriptor allocate and memory maping from
interface cmdq_init.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It needs initialize mdio in initialization process, but reset process
does not reset mdio, so do not initialize mdio in reset process.
This patch move out the mdio configuration function from the mac_init.
So mac_init can be used both in reset process and initialization process.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactor the mapping of tqp to vport, making the maping function
can be used both in the reset process and initialization process.
Signed-off-by: qumingguang <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the timer conversion patches evidently escaped build testing
until I ran into in on ARM randconfig builds:
drivers/net/ethernet/seeq/ether3.c: In function 'ether3_ledoff':
drivers/net/ethernet/seeq/ether3.c:175:40: error: 'priv' undeclared (first use in this function); did you mean 'pid'?
drivers/net/ethernet/seeq/ether3.c:176:27: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
This fixes the two small typos that caused the problems.
Fixes: 6fd9c53f71 ("net: seeq: Convert timers to use timer_setup()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We split rvector stats into two categories - per queue and
stats which are added up into one total counter. Improve
the defines denoting their number.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a counter incremented when allocation of replacement
RX page fails.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the dev_alloc_page() networking helper to allocate pages
for RX packets.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If kernel config does not include BPF just replace the BPF
app handler with the handler for basic NIC. The BPF app
will now be built only if BPF infrastructure is selected
in kernel config.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The app table is an unordered array right now. We have to search
apps by ID. It also makes it harder to fall back to core NIC if
advanced functions are not compiled into the kernel (e.g. eBPF).
Make the table keyed by app id.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent TC changes dropped the check protecting us from trying
to offload a TC program if XDP programs are already loaded.
Fixes: 90d97315b3 ("nfp: bpf: Convert ndo_setup_tc offloads to block callbacks")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions called by the netevent notifier must be in atomic context.
Change the mutex to spinlock and ensure mem allocations are done with the
atomic flag.
Also, remove unnecessary locking after notifiers are unregistered.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure priv netdev data in flower app is cast to nfp_repr and not nfp_net
as in other apps.
Fixes: 363fc53b8b ("nfp: flower: Convert ndo_setup_tc offloads to block callbacks")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LiquidIO firmware supports a vswitch that needs to know the names of the
VF representors in the host to maintain compatibility for direct
programming using external Openflow agents. So, for each VF representor,
send its name to the firmware when it gets registered and when its name
changes.
Signed-off-by: Vijaya Mohan Guvva <vijaya.guvva@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hesoteric board configurations where port 0 is not available would still
make SYSTEMPORT inspect the switch port 0, queue 0, which, not being
enabled, would cause transmit timeouts over time. Just ignore those
unconfigured rings instead.
Fixes: 84ff33eeb23d ("net: systemport: Establish DSA network device queue mapping")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch supports BPF_NEG under both BPF_ALU64 and BPF_ALU. LLVM recently
starts to generate it.
NOTE: BPF_NEG takes single operand which is an register and serve as both
input and output.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
