The commit [i2c: omap: use revision check for OMAP_I2C_FLAG_APPLY_ERRATA_I207]
uses the revision id instead of the flag. So the flag can be safely removed.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The dtrev is used only for the comments. Remove the same and use
the scheme instead to know if it is version2.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The errata i207 is enabled for 2430 and 3xxx. Use the revision check
to enable the erratum instead.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The revision register on OMAP4 is a 16-bit lo and a 16-bit
hi. Currently the driver reads only the lower 8-bits.
Fix the same by preventing the truncating of the rev register
for OMAP4.
Also use the scheme bit ie bit-14 of the hi register to know if it
is OMAP_I2C_IP_VERSION_2.
On platforms previous to OMAP4 the offset 0x04 is IE register whose
bit-14 reset value is 0, the code uses the same to its advantage.
Also since the omap_i2c_read_reg uses reg_map_ip_* a raw_readw is done
to fetch the revision register.
The dev->regs is populated after reading the rev_hi. A NULL check
has been added in the resume handler to prevent the access before
the setting of the regs.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Some GPIO expanders need some early pin control muxing. Due to
legacy boards sometimes the driver uses subsys_initcall instead of
module_init. This patch takes advantage of defer probe feature
and pin control in order to wait until pin control probing before
GPIO driver probing. It has been tested on OMAP5 board with TCA6424
driver.
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Acked-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
if we allow compiler reorder our writes, we could
fall into a situation where dev->buf_len is reset
for no apparent reason.
This bug was found with a simple script which would
transfer data to an i2c client from 1 to 1024 bytes
(a simple for loop), when we got to transfer sizes
bigger than the fifo size, dev->buf_len was reset
to zero before we had an oportunity to handle XDR
Interrupt. Because dev->buf_len was zero, we entered
omap_i2c_transmit_data() to transfer zero bytes,
which would mean we would just silently exit
omap_i2c_transmit_data() without actually writing
anything to DATA register. That would cause XDR
IRQ to trigger forever and we would never transfer
the remaining bytes.
After adding the memory barrier, we also drop resetting
dev->buf_len to zero in omap_i2c_xfer_msg() because
both omap_i2c_transmit_data() and omap_i2c_receive_data()
will act until dev->buf_len reaches zero, rendering the
other write in omap_i2c_xfer_msg() redundant.
This patch has been tested with pandaboard for a few
iterations of the script mentioned above.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
if we allow compiler reorder our writes, we could
fall into a situation where dev->buf_len is reset
for no apparent reason.
This bug was found with a simple script which would
transfer data to an i2c client from 1 to 1024 bytes
(a simple for loop), when we got to transfer sizes
bigger than the fifo size, dev->buf_len was reset
to zero before we had an oportunity to handle XDR
Interrupt. Because dev->buf_len was zero, we entered
omap_i2c_transmit_data() to transfer zero bytes,
which would mean we would just silently exit
omap_i2c_transmit_data() without actually writing
anything to DATA register. That would cause XDR
IRQ to trigger forever and we would never transfer
the remaining bytes.
After adding the memory barrier, we also drop resetting
dev->buf_len to zero in omap_i2c_xfer_msg() because
both omap_i2c_transmit_data() and omap_i2c_receive_data()
will act until dev->buf_len reaches zero, rendering the
other write in omap_i2c_xfer_msg() redundant.
This patch has been tested with pandaboard for a few
iterations of the script mentioned above.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The driver claims to support SMBus quick command but it was not the
case. This patch fixes this issue. Without it, i2cdetect finds imaginary
devices. And with some IP versions, trying to send 0 byte can cause
issue when writing data to an EEPROM.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[wsa: improved the commit message]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The driver claims to support SMBus quick command but it was not the
case. This patch fixes this issue. Without it, i2cdetect finds imaginary
devices. And with some IP versions, trying to send 0 byte can cause
issue when writing data to an EEPROM.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[wsa: improved the commit message]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
When having multiple i2c-gpio nodes, the name for each is same.
So add the patch to fix it.
The adap->name printing information was added by myself
without this patch the log information is as following
---<8---
adap->name = i2c-gpio-1
i2c-gpio i2c.2: using pins 30 (SDA) and 31 (SCL)
adap->name = i2c-gpio-1
i2c-gpio i2c.3: using pins 64 (SDA) and 65 (SCL)
--->8---
with this patch, the log information is as following
---<8---
adap->name = i2c.2
i2c-gpio i2c.2: using pins 30 (SDA) and 31 (SCL)
adap->name = i2c.3
i2c-gpio i2c.3: using pins 64 (SDA) and 65 (SCL)
--->8---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
[wsa: minor fixes to the commit mesage]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
When allocating the memory for i2c busses, the code checked the wrong
variable and thus never detected if there was a memory error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Replacing the devm_request_mem_region() and devm_ioremap_nocache() calls
by a single call to devm_request_and_ioremap() simplifies the code.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Give the driver struct a name according to the 'standard' to fix:
WARNING: vmlinux.o(.data+0x11798): Section mismatch in reference from the variable rcar_i2c_drv to the function .devinit.text:rcar_i2c_probe()
...
WARNING: vmlinux.o(.data+0x1179c): Section mismatch in reference from the variable rcar_i2c_drv to the function .devexit.text:rcar_i2c_remove()
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.
So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Pull i2c embedded fixes from Wolfram Sang:
"Two patches are usual stuff.
The bigger patch is needed to correct a wrong decision made in this
merge window. We hoped to get the PIOQUEUE mode in the mxs driver
working with DMA, but it turned out to be too broken (leading to data
loss), so we now think it is best to remove it entirely and work only
with DMA now. The patch should be in 3.7. IMO, so users never get
the chance to use both modes in parallel."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: tegra: set irq name as device name
i2c-nomadik: Fixup clock handling
i2c: mxs: remove broken PIOQUEUE support
When watching the irqs name of tegra i2c, all instances
irq name shows as tegra_i2c.
Passing the device name properly to have the irq names with
instance like tegra-i2c.0, tegra-i2c.1 etc.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make sure to clk_prepare as well as clk_enable.
Signed-off-by: Philippe Begnic <philippe.begnic@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This I2C master can do DMA and PIOQUEUE (PIO with FIFO). Originally,
only PIOQUEUE was supported and it had issues, then DMA support was added
this cycle. The original intention was to keep PIOQUEUE since it has
less overhead what is nice for small transfers. However, runtime
switching between PIOQEUE and DMA depending on the transfer size never
worked despite a lot of trying. Since PIOQUEUE mode itself was flaky
(polling at places where interrupts failed to work) and the
implementation also imposed a size limit for transfers, it is best to
remove the support, so users don't fall over its limitations. It also
makes the driver a lot cleaner and more robust. If somebody really wants
less overhead, plain PIO mode could still be implemented with the
addidtional advantage that this mode is also available on MX23, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Arbitrarily selecting GPIOLIB causes trouble on some architectures,
so don't do that. Instead, just make the optional multiplexing code
depend on CONFIG_I2C_MUX_GPIO instead of CONFIG_I2C_MUX for now. We
can revisit if the i2c-i801 driver ever supports other multiplexing
flavors.
Also make that optional code depend on DMI, as it won't do anything
without that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Move the i2c-stub driver to drivers/i2c, to match the Kconfig entry.
This is less confusing that way.
I also fixed all checkpatch warnings and errors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Huewe <peterhuewe@gmx.de>
This is some amount of work left/forgot from device tree conversion.
Instead of checking cpu_is_xxx to determine the controller type, the
driver should use platform_device_id, which should match the device
tree compatible string.
The patch changes the driver to use platform_device_id rather than
cpu_is_xxx to determine the controller type/version. It also updates
the platform code and device tree source accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: linux-i2c@vger.kernel.org
Pull i2c-embedded changes from Wolfram Sang:
"The changes for i2c-embedded include:
- massive rework of the omap driver
- massive rework of the at91 driver. In fact, the old driver gets
removed; I am okay with this approach since the old driver was
depending on BROKEN and its limitations made it practically
unusable, so people used bitbanging instead. But even if there are
users, there is no platform_data or module parameter which would
need to be converted. It is just another driver doing I2C
transfers, just way better. Modifications of arch/arm/at91 related
files have proper acks from the maintainer.
- new driver for R-Car I2C
- devicetree and generic_clock conversions and fixes
- usual driver fixes and changes.
The rework patches have come a long way and lots of people have been
involved in creating/testing them. Most patches have been in
linux-next at least since 3.6-rc5. A few have been added in the last
week, I have to admit.
An unexpected (but welcome :)) peak in private life is the cause for
that. The "late" patches shouldn't cause any merge conflicts and I
will have a special eye on them during the stabilization phase. This
is an exception and I want to have the patches in place properly in
time again for the next kernels."
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (44 commits)
MXS: Implement DMA support into mxs-i2c
i2c: add Renesas R-Car I2C driver
i2c: s3c2410: use clk_prepare_enable and clk_disable_unprepare
ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints
i2c: nomadik: Add Device Tree support to the Nomadik I2C driver
i2c: algo: pca: Fix chip reset function for PCA9665
i2c: mpc: Wait for STOP to hit the bus
i2c: davinci: preparation for switch to common clock framework
omap-i2c: fix incorrect log message when using a device tree
i2c: omap: sanitize exit path
i2c: omap: switch over to autosuspend API
i2c: omap: remove unnecessary pm_runtime_suspended check
i2c: omap: switch to threaded IRQ support
i2c: omap: remove redundant status read
i2c: omap: get rid of the "complete" label
i2c: omap: resize fifos before each message
i2c: omap: simplify IRQ exit path
i2c: omap: always return IRQ_HANDLED
i2c: omap: simplify errata check
i2c: omap: bus: add a receiver flag
...
This patch implements DMA support into mxs-i2c. DMA transfers are now enabled
via DT. The DMA operation is enabled by default.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
[wsa: rebased to 3.6-rc7]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQX7MuAAoJEHm+PkMAQRiG0h0IAJURkrMCAQUxA+Ik66ReH89s
LQcVd0U9uL4UUOi7f5WR64Vf9Cfu6VVGX9ZKSvjpNskvlQaUQPMIt4pMe6g4X4dI
u0bApEy4XZz3nGabUAghIU8jJ8cDmhCG6kPpSiS7pi7KHc0yIa4WFtJRrIpGaIWT
xuK38YOiOHcSDRlLyWZzainMncQp/ixJdxnqVMTonkVLk0q0b84XzOr4/qlLE5lU
i+TsK3PRKdQXgvZ4CebL+srPBwWX1dmgP3VkeBloQbSSenSeELICbFWavn2ml+sF
GXi4dO93oNquL/Oy5SwI666T4uNcrRPaS+5X+xSZgBW/y2aQVJVJuNZg6ZP/uWk=
=0v2l
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc7' into i2c-embedded/for-next
Linux 3.6-rc7
Needed to get updates from i2c-embedded/for-current into i2c-embedded/for-next
R-Car I2C is similar with SH7760 I2C.
But the SH7760 I2C driver had many workaround operations, since H/W had bugs.
Thus, it was pointless to keep compatible between SH7760 and R-Car I2C drivers.
This patch creates new Renesas R-Car I2C driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Pul ACPI & Power Management updates from Len Brown:
- acpidump utility added
- intel_idle driver now supports IVB Xeon
- turbostat utility can now count SMIs
- ACPI can now bind to USB3 hubs
- misc fixes
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (49 commits)
ACPI: Add new sysfs interface to export device description
ACPI: Harden acpi_table_parse_entries() against BIOS bug
tools/power/turbostat: add option to count SMIs, re-name some options
tools/power turbostat: add [-d MSR#][-D MSR#] options to print counter deltas
intel_idle: enable IVB Xeon support
tools/power turbostat: add [-m MSR#] option
tools/power turbostat: make -M output pretty
tools/power turbostat: print more turbo-limit information
tools/power turbostat: delete unused line
tools/power turbostat: run on IVB Xeon
tools/power/acpi/acpidump: create acpidump(8), local make install targets
tools/power/acpi/acpidump: version 20101221 - find dynamic tables in sysfs
ACPI: run _OSC after ACPI_FULL_INITIALIZATION
tools/power/acpi/acpidump: create acpidump(8), local make install targets
tools/power/acpi/acpidump: version 20101221 - find dynamic tables in sysfs
tools/power/acpi/acpidump: version 20071116
tools/power/acpi/acpidump: version 20070714
tools/power/acpi/acpidump: version 20060606
tools/power/acpi/acpidump: version 20051111
xo15-ebook: convert to module_acpi_driver()
...
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Convert the driver from the outdated omap_pm_set_max_mpu_wakeup_lat
API to the new PM QoS API.
Since the constraint is on the MPU subsystem, use the PM_QOS_CPU_DMA_LATENCY
class of PM QoS. The resulting MPU constraints are used by cpuidle to
decide the next power state of the MPU subsystem.
The I2C device latency timing is derived from the FIFO size and the
clock speed and so is applicable to all OMAP SoCs.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Here we apply the bindings required for successful Device Tree
probing of the i2c-nomadik driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The parameter passed to pca9665_reset is adap->data (which is bus driver
specific), not i2c_algp_pca_data *adap. pca9665_reset expects it to be
i2c_algp_pca_data *adap. All other wrappers from the algo call back to
the bus driver, which knows to handle its custom data. Only pca9665_reset
resides inside the algorithm code and does not know how to handle a custom
data structure. This can result in a kernel crash.
Fix by re-factoring pca_reset() from a macro to a function handling chip
specific code, and only call adap->reset_chip() if the chip is not PCA9665.
Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Now that i2c-mux-gpio is able to find the GPIO chip by itself, we can
delegate this task. The great thing here is that i2c-mux-gpio can
defer device probing until the gpio chip is available, so we no longer
depend on the module loading order.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The code instantiating an i2c-mux-gpio platform device doesn't
necessarily know in advance the GPIO pin numbers it wants to use. If
pins are on a GPIO device which gets its base GPIO number assigned
dynamically at run-time, the values can't be hard-coded.
In that case, let the caller tell i2c-mux-gpio the name of the GPIO
chip and the (relative) GPIO pin numbers to use. At probe time, the
i2c-mux-gpio driver will look for the chip and apply the proper offset
to turn relative GPIO pin numbers to absolute GPIO pin numbers.
The same could be (and was so far) done on the caller's end, however
doing it in i2c-mux-gpio has two benefits:
* It avoids duplicating the code on every caller's side (about 30
lines of code.)
* It allows for deferred probing for the muxed part of the I2C bus
only. If finding the GPIO chip is the caller's responsibility, then
deferred probing (if the GPIO chip isn't there yet) will not only
affect the mux and the I2C bus segments behind it, but also the I2C
bus trunk.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Use the devm_kzalloc managed function to stripdown the error and remove
code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for SMBus multiplexing on Asus Z8 motherboard series. On
these boards, the memory slots are behind a GPIO-controlled I2C
multiplexer. Models with 6 or 12 memory slots have 2 segments behind
the multiplexer, while models with 18 memory slots have 3 such
segments.
On these boards, only the memory slots are behind the multiplexer,
so it is possible to keep the autodetection mechanism.
The code is generic enough so it could work on other boards as long as
the multiplexer is controlled by GPIO pins. For other forms of
multiplexing (for example using an I2C device) additional code will be
needed.
Thanks to Asus for providing a board to develop and test this feature,
as well as all the technical information required.
At the moment, the GPIO driver must be loaded before the i2c-i801
driver, but I hope to solve this soon, using deferred probing on
the i2c-mux-gpio side.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The SMBus controller in the VIA VX900 appears to be compatible with
the VIA VX855, so just add the device ID.
This closes kernel bug #43096.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c_dw_xfer_msg is only called internally so it can be static. It
original was, before the driver split. No idea why it was changed at
that time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Replace printks with pr_<level>s, add pr_fmt()s to replace NAMEs
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Reviewed-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the global dependency of the I2C subsystem on HAS_IOMEM and
move the dependency to the i2c/busses submenu, with an exception for
i2c-stub.
The generic I2C part does not need to have HAS_IOMEM set and thus now
becomes available in UML, so the I2C subsystem can now be used, e.g.
by the i2c-stub driver, for development of I2C device drivers.
[JD: Some adjustments.]
[Heiko Carstens: Keep I2C disabled on S390.]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Converting kzalloc to devm_kzalloc simplifies the code and ensures that the
result, alert, is freed after the irq allocated by the subsequent
devm_request_irq. This in turn ensures that when an interrupt can be
triggered, the alert structure is still available.
The problem of a free after a devm_request_irq was found using the
following semantic match (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2,x,a,b,c,d;
identifier free;
position p1,p2;
@@
devm_request_irq@p1(e1,e2,...,x)
... when any
when != e2 = a
when != x = b
if (...) {
... when != e2 = c
when != x = d
free@p2(...,x,...);
...
return ...;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let I2C bus segments behind multiplexers have a class. This allows for
device auto-detection on these segments. As long as parent segments
don't share the same class, it should be fine.
I implemented support in drivers i2c-mux-gpio and i2c-mux-pca954x. I
left i2c-mux-pca9541 and i2c-mux-pinctrl alone for the moment as I
don't know if this feature makes sense for the use cases of these
drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Cc: Rodolfo Giometti <giometti@linux.it>
To avoid name conflicts:
drivers/video/riva/fbdev.c:281:9: sparse: preprocessor token MAX_LEVEL redefined
While at it, also make the other names more consistent and add
parentheses.
[akpm@linux-foundation.org: repair fallout]
[sfr@canb.auug.org.au: IB/mlx4: fix for MAX_ID_MASK to MAX_IDR_MASK name change]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at>
Cc: walter harms <wharms@bfs.de>
Cc: Glauber Costa <glommer@parallels.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck7M
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc driver specific changes from Olof Johansson:
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
Fix up conflicts as per Olof.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: bus: omap_l3: use resources instead of hardcoded irqs
pinctrl: exynos: Fix wakeup IRQ domain registration check
pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
pinctrl: exynos: Correct the detection of wakeup-eint node
pinctrl: exynos: Mark exynos_irq_demux_eint as inline
pinctrl: exynos: Handle only unmasked wakeup interrupts
pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
drivers: bus: Move the OMAP interconnect driver to drivers/bus/
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
...
This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used with
a mainline kernel. We have not been able to find anyone interested
in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck1u
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the samsung include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: linux-samsung-soc@vger.kernel.org
Pull i2c embedded fixes from Wolfram Sang:
"The last bunch of (typical) i2c-embedded driver fixes for 3.6.
Also update the MAINTAINERS file to point to my tree since people keep
asking where to find their patches."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: algo: pca: Fix mode selection for PCA9665
MAINTAINERS: fix tree for current i2c-embedded development
i2c: mxs: correctly setup speed for non devicetree
i2c: pnx: Fix read transactions of >= 2 bytes
i2c: pnx: Fix bit definitions
mpc_i2c_stop() only initiates STOP but does not wait for it to
hit the I2C bus. This is a problem when using I2C devices which
uses fairly long clock stretching just before STOP if you also
have an i2c-mux which may switch to another bus before STOP has
been processed.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The code currently always selects turbo mode for PCA9665, no matter which
clock frequency is configured. This is because it compares the clock frequency
against constants reflecting (boundary / 100). Compare against real boundary
frequencies to fix the problem.
Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
As a first step towards migrating davinci platforms to use common clock
framework, replace all instances of clk_enable() with clk_prepare_enable()
and clk_disable() with clk_disable_unprepare(). Until the platform is
switched to use the CONFIG_HAVE_CLK_PREPARE Kconfig variable, this just
adds a might_sleep() call and would work without any issues.
This will make it easy later to switch to common clk based implementation
of clk driver from DaVinci specific driver.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the w90x900 include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the imx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the davinci include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Ben Dooks" <ben-linux@fluff.org>
Cc: "Wolfram Sang" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: davinci-linux-open-source@linux.davincidsp.com
Tegra I2C driver enables the fast clock during initialization
and does not disable till driver removed.
Enable this clock before transfer and disable after transfer done.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra20 i2c controller does not support the continue transfer
which implements the I2C_M_NOSTART functionality of i2c
protocol mangling.
Removing the I2C_M_NOSTART functionality support for Tegra20.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra's i2c controller require two clock sources named as
div_clk and fast_clk.
This change make sure that driver pass the correct clock's
name when it acquires clock handle. Also change the
variable name to reflect the correct clock handles.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
From "Uwe Kleine-Knig" <u.kleine-koenig@pengutronix.de>:
this is the 2nd version of this series whose goal is to make struct
of_device_id.data const. Conceptually a driver must not modify the data
contained there so making it const is the right thing.
v1 of this series was sent with Message-id:
1342182734-321-1-git-send-email-y. Changes since then are:
- powerpc fixes
- several new consts that were found by Arnd that are possible after
patch 19.
Arnd suggested to take this series via arm-soc late for 3.6 in one go
because patch 19 depends on the former patches but is a precondition to
the latter and it fixes a few warnings. So getting it in via the
respective maintainer trees would need a much bigger coordination
effort. That means I prefer getting Acks over you taking the patch.
Vinod Koul already took
dmaengine: at_hdmac: add a few const qualifiers
that is in next-20120723 as 7fd63ccdad now. Vinod, I don't follow your
pull requests, but assuming you didn't let it already pull for 3.6 I
suggest you drop it from your queue and I just take your Ack.
This series was build tested for arm (all defconfigs) and powerpc (all
defconfigs and an allyesconfig) and grep didn't find more issues. As
before it introduces a warning in drivers/regulator/twl-regulator.c.
This driver does modify its .of_match_table when a device is bound which
doesn't fits the concept of independant devices. Arnd noticed another
new warning in drivers/scsi/qlogicpti.c that isn't that easy to resolve,
because the pointer to (now) const data is passed as first argument to
scsi_host_alloc. To fix that properly struct Scsi_Host.hostt needs to
get a const, too. Alternatively I could introduce a cast removing the
const, but I don't like that.
* 'ofdeviceiddata' of git://git.pengutronix.de/git/ukl/linux: (25 commits)
dma: tegra: make data used as *of_device_id.data const
can: mpc5xxx_can: make data used as *of_device_id.data const
macintosh/mediabay: make data used as *of_device_id.data const
i2c/mpc: make data used as *of_device_id.data const
mfd/da9052: make i2c_device_id array const
powerpc/fsl_msi: drop unneeded cast to non-const pointer
gpio/gpio-omap: make platformdata used as *of_device_id.data const
of: add const to struct *of_device_id.data
dma: tegra: make tegra_dma.chip_data a pointer to const data
watchdog/mpc8xxx: add a const qualifier
powerpc/celleb_pci: add a const qualifier
powerpc/fsl_msi: add a const qualifier
powerpc/83xx: add a const qualifier
macintosh/mediabay: add a const qualifier
mmc/omap_hsmmc: add a const qualifier
i2c/mpc: add a const qualifier
i2c/i2c-omap: add a const qualifier
gpio/mpc8xxx: add a const qualifier
gpio/gpio-omap.c: add a const qualifier
misc/atmel_tc: make atmel_tc.tcb_config member point to const data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: repulled a v3 version of the branch that rebased to add some more
acked-bys and added one more patch on top for tegra]
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit cd4f2d4 (i2c: mxs: Set I2C timing registers for mxs-i2c) only
covered the case for devicetree and made platform_data based boards
bail out with -EINVAL. Correctly support the latter one, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
On transactions with n>=2 bytes, the controller actually wrongly clocks in n+1
bytes. This is caused by the (wrong) assumption that RFE in the Status Register
is 1 iff there is no byte already ordered (via a dummy TX byte). This lead to
the implementation of synchronized byte ordering, e.g.:
Dummy-TX - RX - Dummy-TX - RX - ...
But since RFE actually stays high after some Dummy-TX, it rather looks like:
Dummy-TX - Dummy-TX - RX - Dummy-TX - RX - (RX)
The last RX byte is clocked in by the bus controller, but ignored by the kernel
when filling the userspace buffer.
This patch fixes the issue by asking for RX via Dummy-TX asynchronously.
Introducing a separate counter for TX bytes.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The I2C Control Register bits RFDAIE and RFFIE were mixed up. In addition to
this fix, this patch adds the missing bit DRSIE for completeness.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
When booting using a device tree, the adapter number is dynamically
assigned after the log message is sent.
This patch modifies the log message to get a correct adapter id.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
move the goto out label one line down, so that
it can be used when stat is read as zero. All
other exits, can be done with a break statement.
While at that, also break out as soon as we
complete draining IRQ, since at that time
we know we transferred everything there was
to be transferred.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
this helps us reduce unnecessary pm transitions
in case we have another i2c message starting soon.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
before starting any messages we call pm_runtime_get_sync()
which will make sure that by the time we program a transfer
and our IRQ handler gets called, we're not suspended
anymore.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
for OMAP2, we can easily switch over to threaded
IRQs on the I2C driver. This will allow us to
spend less time in hardirq context.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[Trivial formating changes]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently omap_i2c_ack_stat doesn't use the stat variable.
After the read of the I2C_STAT_REG it is not used.
Remove the redundant read of the status register.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
we can ack stat and complete the command from
the errata handling itself.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch will try to avoid the usage of
draining feature by reconfiguring the FIFO
the start condition of each message based
on the message's size.
By doing that, we will be better utilizing
the FIFO when doing big transfers.
While at that also drop the now unneeded
check for dev->buf_len as we always know
the amount of data to be transmitted.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
instead of having multiple return points, use
a goto statement to make that clearer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Always return IRQ_HANDLED otherwise we could get our IRQ line disabled due
to many spurious IRQs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[Trivial changes to commitlogs]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
omap_i2c_dev is allocated with kzalloc(),
so we need not initialize b_hw to zero.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
that way we can ignore TX IRQs while in receiver
mode and ignore RX IRQs while in transmitter mode.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[Remove unnecessary braces]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
that's a nice helper from drivers core which
will give us the exact IRQ number, instead
of a pointer to an IRQ resource.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
According to flow diagrams on OMAP TRMs,
we should ACK the IRQ as they happen.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[Ack the stat OMAP_I2C_STAT_AL in case of arbitration lost]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
this will make sure that we execute at least once.
No functional changes otherwise.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
re-factor the common parts to a separate function,
so that code is easier to read and understand.
No functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make it not depend on ISR's local variables
in order to make it easier to re-factor the
transmit data loop.
Also since we are waiting for XUDF(Transmitter underflow) just before
writing data lets not flag the underflow.
This is anyways going to go once we write
the data.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
While they do pretty much the same thing, there
are a few peculiarities. Specially WRT erratas,
it's best to split those out and re-factor the
read/write loop to another function which both
cases call.
This last part will be done on another patch.
While at that, also avoid an unncessary register
read since dev->fifo_len will always contain the
correct amount of data to be transferred.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
stat & BIT(1) is the same as BIT(1), so let's
simplify things a bit by removing "stat &" from
all omap_i2c_ack_stat() calls.
Code snippet (extremely simplified):
if (stat & NACK) {
...
omap_i2c_ack_stat(dev, stat & NACK);
}
if (stat & RDR) {
...
omap_i2c_ack_stat(dev, stat & RDR);
}
and so on. The tricky place is only WRT errata handling, for example:
if (*stat & (NACK | AL)) {
omap_i2c_ack_stat(dev, *stat & (XRDY | XDR));
...
}
but in this case, the errata says we must clear XRDY and XDR if that
errata triggers, so if they just got enabled or not, it doesn't matter.
Another tricky place is RDR | RRDY (likewise for XDR | XRDY):
if (stat & (RDR | RRDY)) {
...
omap_i2c_ack_stat(dev, stat & (RDR | RRDY));
}
again here there will be no issues because those IRQs never fire
simultaneously and one will only after after we have handled the
previous, that's because the same FIFO is used anyway and we won't shift
data into FIFO until we tell the IP "hey, I'm done with the FIFO, you
can shift more data"
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
[Added the explaination from the discurssion to the commit logs]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
trivial patch to aid readability. No functional
changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The patch intends to decrease the indentation level on the
data handling
by using the fact that else of if (dev->buf_len) is same as
if (!dev->buf_len)
if (dev->buf_len) {
aaa;
} else {
bbb;
break;
}
to
if (!dev->buf_len) {
bbb;
break;
}
aaa;
Hence no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
trivial patch, no functional changes
If the fifo is disabled or fifo_size is 0 the num_bytes
is set to 1. Else it is set to fifo_size or in case of a
draining interrupt the remaining bytes in the buff stat.
So the zero check is redundant and can be safely optimised.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
that helps deleting some boiler plate code
and lets driver-core manage our resources
for us.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This driver has the following properties compared to the old driver:
1. Support for multiple interfaces.
2. Interrupt driven I/O as opposed to polling/busy waiting.
3. Support for _one_ repeated start (Sr) condition, which is enough
for most real-world applications including all SMBus transfer types.
(The hardware does not support issuing arbitrary Sr conditions on the
bus.)
testing: SoC: at91sam9g45
- BQ20Z80 battery SMBus client.
- on a 2.6.38 kernel with several i2c clients (temp-sensor,
audio-codec, touchscreen-controller, w1-bridge, io-expanders)
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Hubert Feurstein <h.feurstein@gmail.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[wsa: squashed with the following patches from Ludovic to have some flaws
fixed:
i2c: at91: use managed resources
i2c: at91: add warning about transmission issues for some devices
i2c: at91: use an id table for SoC dependent parameters
]
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
It will get replaced by a superior one. Safe to remove since this one
depends on BROKEN anyhow.
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[wsa: added commit message]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The regulator fetched by the Nomadik I2C driver is actually a
voltage domain regulator. Stop doing this in the driver and
let the power domain code handle any regulators, as discussed
on the list.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
add of support for the davinci i2c driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[wsa: fix indentation in the binding description]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Use dev_dbg logging style as it is done in other parts of this driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
