Otherwise, the configured IPv6 address could be still "tentative"
at test time, possibly causing tests failures.
We can also drop some sleep along the code and decrease the
timeout for most commands so that the test runtime decreases.
v1 -> v2:
- fix comment (Stefano)
Fixes: d1f1b9cbf3 ("selftests: net: Introduce first PMTU test")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to dp83640 delay after soft reset
is needed to set up registers correctly.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.
DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).
END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.
WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
register 2, prior to connecting the cable or prior to setting the
Restart Auto-negotiation bit in register 0h. The MMD registers are
accessed via the indirect access registers Dh and Eh, or via the Micrel
EthUtil utility as shown here:
. if using the EthUtil utility (usually with a Micrel KSZ8061
Evaluation Board), type the following commands:
> address 1
> mmd 1
> iw 2 b61a
. Alternatively, write the following registers to write to the
indirect MMD register:
Write register Dh, data 0001h
Write register Eh, data 0002h
Write register Dh, data 4001h
Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
either by the strapping option, or by clearing bit 12 in register 0h.
Care must be taken to ensure that the KSZ8061 and the link partner
will link with the same speed and duplex. Note that the KSZ8061
defaults to full-duplex when auto-negotiation is off, but other
devices may default to half-duplex in the event of failed
auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
be recovered by setting the Restart Auto-Negotiation bit in
register 0h, or by resetting or power cycling the device. Reset may
be either hardware reset or software reset (register 0h, bit 15).
PLAN
This errata will not be corrected in the future revision.
Fixes: 7ab59dc15e ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: Alexander Onnasch <alexander.onnasch@landisgyr.com>
Signed-off-by: Rajasingh Thavamani <T.Rajasingh@landisgyr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_msg_init() API takes on input the amount of bits to be set. The
description of debug parameter in the enc28j60 module is misleading in this
sense and passing 0xffff does not give an expected behaviour.
Fix the description of debug module parameter to show what exactly is expected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1 << 31 is Undefined Behaviour according to the C standard.
Use U type modifier to avoid theoretical overflow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been reports of oversize UDP packets being sent to the
driver to be transmitted, causing error conditions. The issue is
likely caused by the dst of the SKB switching between 'lo' with
64K MTU and the hardware device with a smaller MTU. Patches are
being proposed by Mahesh Bandewar <maheshb@google.com> to fix the
issue.
In the meantime, add a quick length check in the driver to prevent
the error. The driver uses the TX packet size as index to look up an
array to setup the TX BD. The array is large enough to support all MTU
sizes supported by the driver. The oversize TX packet causes the
driver to index beyond the array and put garbage values into the
TX BD. Add a simple check to prevent this.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending multicast messages via blocking socket,
if sending link is congested (tsk->cong_link_cnt is set to 1),
the sending thread will be put into sleeping state. However,
tipc_sk_filter_rcv() is called under socket spin lock but
tipc_wait_for_cond() is not. So, there is no guarantee that
the setting of tsk->cong_link_cnt to 0 in tipc_sk_proto_rcv() in
CPU-1 will be perceived by CPU-0. If that is the case, the sending
thread in CPU-0 after being waken up, will continue to see
tsk->cong_link_cnt as 1 and put the sending thread into sleeping
state again. The sending thread will sleep forever.
CPU-0 | CPU-1
tipc_wait_for_cond() |
{ |
// condition_ = !tsk->cong_link_cnt |
while ((rc_ = !(condition_))) { |
... |
release_sock(sk_); |
wait_woken(); |
| if (!sock_owned_by_user(sk))
| tipc_sk_filter_rcv()
| {
| ...
| tipc_sk_proto_rcv()
| {
| ...
| tsk->cong_link_cnt--;
| ...
| sk->sk_write_space(sk);
| ...
| }
| ...
| }
sched_annotate_sleep(); |
lock_sock(sk_); |
remove_wait_queue(); |
} |
} |
This commit fixes it by adding memory barrier to tipc_sk_proto_rcv()
and tipc_wait_for_cond().
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incoming packets may have IP header checksum verified by the host.
They may not have IP header checksum computed after coalescing.
This patch re-compute the checksum when necessary, otherwise the
packets may be dropped, because Linux network stack always checks it.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: Fail route add with unsupported nexthop attribute
RTA_VIA was added for MPLS as a way of specifying a gateway from a
different address family. IPv4 and IPv6 do not currently support RTA_VIA
so using it leads to routes that are not what the user intended. Catch
and fail - returning a proper error message.
MPLS on the other hand does not support RTA_GATEWAY since it does not
make sense to have a nexthop from the MPLS address family. Similarly,
catch and fail - returning a proper error message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
MPLS does not support nexthops with an MPLS address family.
Specifically, it does not handle RTA_GATEWAY attribute. Make it
clear by returning an error.
Fixes: 03c0566542 ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 currently does not support nexthops outside of the AF_INET6 family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
$ ip ro ls
...
2001:db8:2::/64 dev eth0 metric 1024 pref medium
Catch this and fail the route add:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
Error: IPv6 does not support RTA_VIA attribute.
Fixes: 03c0566542 ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 currently does not support nexthops outside of the AF_INET family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
$ ip ro ls
...
172.16.1.0/24 dev eth0
Catch this and fail the route add:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
Error: IPv4 does not support RTA_VIA attribute.
Fixes: 03c0566542 ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract IP options in cipso_v4_error and use __icmp_send.
Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __icmp_send function having ip_options struct parameter
Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru>
Reviewed-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace set_current_state with __set_current_state since no memory
barrier is needed at this point.
Signed-off-by: Timur Celik <mail@timurcelik.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9060cb719e ("net: crypto set sk to NULL when af_alg_release.")
fixed a use-after-free in sockfs_setattr() when an AF_ALG socket is
closed concurrently with fchownat(). However, it ignored that many
other proto_ops::release() methods don't set sock->sk to NULL and
therefore allow the same use-after-free:
- base_sock_release
- bnep_sock_release
- cmtp_sock_release
- data_sock_release
- dn_release
- hci_sock_release
- hidp_sock_release
- iucv_sock_release
- l2cap_sock_release
- llcp_sock_release
- llc_ui_release
- rawsock_release
- rfcomm_sock_release
- sco_sock_release
- svc_release
- vcc_release
- x25_release
Rather than fixing all these and relying on every socket type to get
this right forever, just make __sock_release() set sock->sk to NULL
itself after calling proto_ops::release().
Reproducer that produces the KASAN splat when any of these socket types
are configured into the kernel:
#include <pthread.h>
#include <stdlib.h>
#include <sys/socket.h>
#include <unistd.h>
pthread_t t;
volatile int fd;
void *close_thread(void *arg)
{
for (;;) {
usleep(rand() % 100);
close(fd);
}
}
int main()
{
pthread_create(&t, NULL, close_thread, NULL);
for (;;) {
fd = socket(rand() % 50, rand() % 11, 0);
fchownat(fd, "", 1000, 1000, 0x1000);
close(fd);
}
}
Fixes: 86741ec254 ("net: core: Add a UID field to struct sock.")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Metadata pointer is only initialized for action TCA_TUNNEL_KEY_ACT_SET, but
it is unconditionally dereferenced in tunnel_key_init() error handler.
Verify that metadata pointer is not NULL before dereferencing it in
tunnel_key_init error handling code.
Fixes: ee28bb56ac ("net/sched: fix memory leak in act_tunnel_key_init()")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./net/dsa/port.c:294:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 284, but without a corresponding object release within this function.
./net/dsa/dsa2.c:627:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:630:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:636:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:639:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves setting of the current state into the loop. Otherwise
the task may end up in a busy wait loop if none of the break conditions
are met.
Signed-off-by: Timur Celik <mail@timurcelik.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the file names of the FW files which this driver handles into
the module description.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
when act_skbedit was converted to use RCU in the data plane, we added an
error path, but we forgot to drop the action refcount in case of failure
during a 'replace' operation:
# tc actions add action skbedit ptype otherhost pass index 100
# tc action show action skbedit
total acts 1
action order 0: skbedit ptype otherhost pass
index 100 ref 1 bind 0
# tc actions replace action skbedit ptype otherhost drop index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action skbedit
total acts 1
action order 0: skbedit ptype otherhost pass
index 100 ref 2 bind 0
Ensure we call tcf_idr_release(), in case 'params_new' allocation failed,
also when the action is being replaced.
Fixes: c749cdda90 ("net/sched: act_skbedit: don't use spinlock in the data path")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 4e8ddd7f17 ("net: sched: don't release reference on action
overwrite"), the error path of all actions was converted to drop refcount
also when the action was being overwritten. But we forgot act_ipt_init(),
in case allocation of 'tname' was not successful:
# tc action add action xt -j LOG --log-prefix hello index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "hello" index 100
# tc action show action xt
total acts 1
action order 0: tablename: mangle hook: NF_IP_POST_ROUTING
target LOG level warning prefix "hello"
index 100 ref 1 bind 0
# tc action replace action xt -j LOG --log-prefix world index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "world" index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action xt
total acts 1
action order 0: tablename: mangle hook: NF_IP_POST_ROUTING
target LOG level warning prefix "hello"
index 100 ref 2 bind 0
Ensure we call tcf_idr_release(), in case 'tname' allocation failed, also
when the action is being replaced.
Fixes: 4e8ddd7f17 ("net: sched: don't release reference on action overwrite")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJcclOnAAoJEL/70l94x66DAjIH/28XLAkaAtJIsm4nTy3sb6nC
UC7suhEEst4zyRCzUlMdeaMkuWJitx5Bun0x9k5uYvMXqmndXcGq3wLmrRhOY2u2
iN1myLESOn0+lubVcK/+ht2rat2AO9XqpOKPojBRs/c6MW1UAIJIPKly/ls1++Ee
TmdIKrgqGgE5Ywx4ObvXBDOeWSKUwxqqNi7FUkWpACJckvmQoKJX0Hre5ICW6lom
+yUBC1rR9apMLTe2QIW2kBZ9JTKCX0aErdmnLXlyZbFOOk0udzNaDy+kXSs7w9Bk
tu8biO7xBNJrcR5e+fEipVFIdN9au0aM5pJWq9s4yeqSnDKB1FRekoJj5yvTqus=
=1GQR
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Bug fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: record maximum physical address width in kvm_mmu_extended_role
kvm: x86: Return LA57 feature based on hardware capability
x86/kvm/mmu: fix switch between root and guest MMUs
s390: vsie: Use effective CRYCBD.31 to check CRYCBD validity
Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:
1) Only refcount ESP stats on full sockets, from Martin Willi.
2) Missing barriers in AF_UNIX, from Al Viro.
3) RCU protection fixes in ipv6 route code, from Paolo Abeni.
4) Avoid false positives in untrusted GSO validation, from Willem de
Bruijn.
5) Forwarded mesh packets in mac80211 need more tailroom allocated,
from Felix Fietkau.
6) Use operstate consistently for linkup in team driver, from George
Wilkie.
7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
and PF code paths.
8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.
9) nfp eBPF code gen fixes from Jiong Wang.
10) bnxt_en firmware timeout fix from Michael Chan.
11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.
12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
net: phy: realtek: Dummy IRQ calls for RTL8366RB
tcp: repaired skbs must init their tso_segs
net/x25: fix a race in x25_bind()
net: dsa: Remove documentation for port_fdb_prepare
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
selftests: fib_tests: sleep after changing carrier. again.
net: set static variable an initial value in atl2_probe()
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
bpf, doc: add bpf list as secondary entry to maintainers file
udp: fix possible user after free in error handler
udpv6: fix possible user after free in error handler
fou6: fix proto error handler argument type
udpv6: add the required annotation to mib type
mdio_bus: Fix use-after-free on device_register fails
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
bnxt_en: Wait longer for the firmware message response to complete.
bnxt_en: Fix typo in firmware message timeout logic.
nfp: bpf: fix ALU32 high bits clearance bug
nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
Documentation: networking: switchdev: Update port parent ID section
...
This fixes a regression introduced by
commit 0d2e778e38
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This callback was removed some time ago, also remove the documentation.
Fixes: 1b6dd556c3 ("net: dsa: Remove prepare phase for FDB")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 5a2de63fd1 ("bridge: do not add port to router list
when receives query with source 0.0.0.0") and commit 0fe5119e26 ("net:
bridge: remove ipv6 zero address check in mcast queries")
The reason is RFC 4541 is not a standard but suggestive. Currently we
will elect 0.0.0.0 as Querier if there is no ip address configured on
bridge. If we do not add the port which recives query with source
0.0.0.0 to router list, the IGMP reports will not be about to forward
to Querier, IGMP data will also not be able to forward to dest.
As Nikolay suggested, revert this change first and add a boolopt api
to disable none-zero election in future if needed.
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reported-by: Sebastian Gottschall <s.gottschall@newmedia-net.de>
Fixes: 5a2de63fd1 ("bridge: do not add port to router list when receives query with source 0.0.0.0")
Fixes: 0fe5119e26 ("net: bridge: remove ipv6 zero address check in mcast queries")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like commit e2ba732a16 ("selftests: fib_tests: sleep after
changing carrier"), wait one second to allow linkwatch to propagate the
carrier change to the stack.
There are two sets of carrier tests. The first slept after the carrier
was set to off, and when the second set ran, it was likely that the
linkwatch would be able to run again without much delay, reducing the
likelihood of a race. However, if you run 'fib_tests.sh -t carrier' on a
loop, you will quickly notice the failures.
Sleeping on the second set of tests make the failures go away.
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cards_found is a static variable, but when it enters atl2_probe(),
cards_found is set to zero, the value is not consistent with last probe,
so next behavior is not our expect.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 20b2af32ff ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
One fix for an oops when using SRIOV, introduced by the recent changes to
support compound IOMMU groups.
Thanks to:
Alexey Kardashevskiy.
-----BEGIN PGP SIGNATURE-----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=NBtz
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.0-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
"One fix for an oops when using SRIOV, introduced by the recent changes
to support compound IOMMU groups.
Thanks to Alexey Kardashevskiy"
* tag 'powerpc-5.0-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv/sriov: Register IOMMU groups for VFs
Four small fixes: three in drivers and one in the core. The core fix
is also minor in scope since the bug it fixes is only known to affect
systems using SCSI reservations. Of the driver bugs, the libsas one
is the most major because it can lead to multiple disks on the same
expander not being exposed.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXHC4uSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfYwAP9zX676
svxUeEQLLyMLXmGyDZ5um8ne8VDAzXDIrkS06gEAhKju7hb7jYvt0pf3jj+utS+v
KXtT8CpMuj+cffeVXng=
=OkZL
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes: three in drivers and one in the core.
The core fix is also minor in scope since the bug it fixes is only
known to affect systems using SCSI reservations. Of the driver bugs,
the libsas one is the most major because it can lead to multiple disks
on the same expander not being exposed"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: reset host byte in DID_NEXUS_FAILURE case
scsi: libsas: Fix rphy phy_identifier for PHYs with end devices attached
scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation
scsi: libiscsi: Fix race between iscsi_xmit_task and iscsi_complete_task
Daniel Borkmann says:
====================
pull-request: bpf 2019-02-23
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a bug in BPF's LPM deletion logic to match correct prefix
length, from Alban.
2) Fix AF_XDP teardown by not destroying umem prematurely as it
is still needed till all outstanding skbs are freed, from Björn.
3) Fix unkillable BPF_PROG_TEST_RUN under preempt kernel by checking
signal_pending() outside need_resched() condition which is never
triggered there, from Stanislav.
4) Fix two nfp JIT bugs, one in code emission for K-based xor, and
another one to explicitly clear upper bits in alu32, from Jiong.
5) Add bpf list address to maintainers file, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull keys fixes from James Morris:
"Two fixes from Eric Biggers"
* 'fixes-v5.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: always initialize keyring_index_key::desc_len
KEYS: user: Align the payload buffer
- Use hrtimer_try_to_cancel() instead of hrtimer_cancel() in the
PM-runtime framework to avoid a possible timer-related deadlock
introduced recently (Vincent Guittot).
- Reorder the scmi-cpufreq driver code to avoid accessing memory
that has just been freed (Yangtao Li).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=7rW+
-----END PGP SIGNATURE-----
Merge tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a regression in the PM-runtime framework introduced by the
recent switch-over of it to using hrtimers and a use-after-free
introduced by one of the recent changes in the scmi-cpufreq driver.
Specifics:
- Use hrtimer_try_to_cancel() instead of hrtimer_cancel() in the
PM-runtime framework to avoid a possible timer-related deadlock
introduced recently (Vincent Guittot).
- Reorder the scmi-cpufreq driver code to avoid accessing memory that
has just been freed (Yangtao Li)"
* tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM-runtime: Fix deadlock when canceling hrtimer
cpufreq: scmi: Fix use-after-free in scmi_cpufreq_exit()
Only a handful of device tree fixes, all simple enough:
NVIDIA Tegra:
- Fix a regression for booting on chromebooks
TI OMAP:
- Two fixes PHY mode on am335x reference boards
Marvell mvebu:
- A regression fix for Armada XP NAND flash controllers
- An incorrect reset signal on the clearfog board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=nXrB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Only a handful of device tree fixes, all simple enough:
NVIDIA Tegra:
- Fix a regression for booting on chromebooks
TI OMAP:
- Two fixes PHY mode on am335x reference boards
Marvell mvebu:
- A regression fix for Armada XP NAND flash controllers
- An incorrect reset signal on the clearfog board"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: tegra: Restore DT ABI on Tegra124 Chromebooks
ARM: dts: am335x-evm: Fix PHY mode for ethernet
ARM: dts: am335x-evmsk: Fix PHY mode for ethernet
arm64: dts: clearfog-gt-8k: fix SGMII PHY reset signal
ARM: dts: armada-xp: fix Armada XP boards NAND description
- Fix memcpy to prevent prefetchw beyond end of buffer [Eugeniy]
- Enable unaligned access early to prevent exceptions given newer gcc
code gen [Eugeniy]
- Tighten up uboot arg checking to prevent false negatives and also
allow both jtag and bootloading to coexist w/o config option as
needed by kernelCi folks [Eugeniy]
- Set slab alignment to 8 for ARC to avoid the atomic64_t unalign [Alexey]
- Disable regfile auto save on interrupts on HSDK platform due to a
silicon issue [Vineet]
- Avoid HS38x boot printing crash by not reading HS48x only reg [Vineet]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cNCN
-----END PGP SIGNATURE-----
Merge tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Fixes for ARC for 5.0, bunch of those are stable fodder anyways so
sooner the better.
- Fix memcpy to prevent prefetchw beyond end of buffer [Eugeniy]
- Enable unaligned access early to prevent exceptions given newer gcc
code gen [Eugeniy]
- Tighten up uboot arg checking to prevent false negatives and also
allow both jtag and bootloading to coexist w/o config option as
needed by kernelCi folks [Eugeniy]
- Set slab alignment to 8 for ARC to avoid the atomic64_t unalign
[Alexey]
- Disable regfile auto save on interrupts on HSDK platform due to a
silicon issue [Vineet]
- Avoid HS38x boot printing crash by not reading HS48x only reg
[Vineet]"
* tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: don't assume core 0x54 has dual issue
ARC: define ARCH_SLAB_MINALIGN = 8
ARC: enable uboot support unconditionally
ARC: U-boot: check arguments paranoidly
ARCv2: support manual regfile save on interrupts
ARC: uacces: remove lp_start, lp_end from clobber list
ARC: fix actionpoints configuration detection
ARCv2: lib: memcpy: fix doing prefetchw outside of buffer
ARCv2: Enable unaligned access in early ASM code
We recently created a bpf@vger.kernel.org list (https://lore.kernel.org/bpf/)
for BPF related discussions, originally in context of BPF track at LSF/MM
for topic discussions. It's *optional* but *desirable* to keep it in Cc for
BPF related kernel/loader/llvm/tooling threads, meaning also infrastructure
like llvm that sits on top of kernel but is crucial to BPF. In any case,
netdev with it's bpf delegate is *as-is* today primary list for patches, so
nothing changes in the workflow. Main purpose is to have some more awareness
for the bpf@vger.kernel.org list that folks can Cc for BPF specific topics.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull parisc fixes from Helge Deller:
"Fix ptrace syscall number modification which has been broken since
kernel v4.5 and provide alternative email addresses for the remaining
users of the retired parisc-linux.org email domain"
* 'parisc-5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
CREDITS/MAINTAINERS: Retire parisc-linux.org email domain
parisc: Fix ptrace syscall number modification
- fix scripts/kallsyms.c to correctly check too long symbol names
- fix sh build error for the combination of CONFIG_OF_EARLY_FLATTREE=y
and CONFIG_USE_BUILTIN_DTB=n
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJcb0FKAAoJED2LAQed4NsGuwcP/2GhoN/whRUpC2LkrsAbkPuy
Ad/ySgwRROUHeLuSQqxFqOIvnkWYwsCRrA/jNzXalapB66iYVAKWupVniuFkv8Lj
TIqXOu3qJfpg63l77GgO87L/ZVxiyWxEH3XEvxFlARQCZEk9nwiTkXD8bVt37xwP
P46RVUQyvS8diUKjS6EO3I74cmBXDDigSzzzJTL6F8GgaGEv8mSMv6pU86CxLSpx
+X8U/1HR3hHsxOH5oYlFY6RVv/f071YtOVdqgTU5OMWQ7R8iaGOy0eJBaDsl4HGx
oNYQhvLs7TN4BT6ubVcNliSqp0SwccSGA0nQkSVS78YvYVF9mIDsmH673kfN5pFT
TYR+LSW8AnWvpQJ7PyJtyKSCD9MEMsi4viAnW/2f1VxCGRV84+A3DotIKekJLa1A
8uuYbOBqKi5LCBY1Vo8LOlG+epw21AsCqHrot73J4u8nkiK3YZdq4zkV4pnb1B49
NLXs1pJIG4Tzu06EOK1iOO5Y76fSCV6/5FfqFwP87hyfTtQU1FG1bsivuXccu/hV
yrUaHdpDRltechPLhN4js8I5zhZTZVZsthn6lITBPcEOmeCbNgIShIdjFIgnqyTr
OQNznQPNt8iOzsC1aaZ0hOpCcE8Hk1RmObEF+xA5i8k5oinAxPX6loTeW7sIY5OP
0Pt9FJQ87Q62+jpX0/jp
=m7U7
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild fixes from Masahiro Yamada:
- fix scripts/kallsyms.c to correctly check too long symbol names
- fix sh build error for the combination of CONFIG_OF_EARLY_FLATTREE=y
and CONFIG_USE_BUILTIN_DTB=n
* tag 'kbuild-fixes-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
sh: fix build error for invisible CONFIG_BUILTIN_DTB_SOURCE
kallsyms: Handle too long symbols in kallsyms.c
Paolo Abeni says:
====================
udp: a few fixes
This series includes some UDP-related fixlet. All this stuff has been
pointed out by the sparse tool. The first two patches are just annotation
related, while the last 2 cover some very unlikely races.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the previous commit, this addresses the same issue for
ipv4: use a single fetch operation and use the correct rcu
annotation.
Fixes: e7cc082455 ("udp: Support for error handlers of tunnels with arbitrary destination port")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before derefencing the encap pointer, commit e7cc082455 ("udp: Support
for error handlers of tunnels with arbitrary destination port") checks
for a NULL value, but the two fetch operation can race with removal.
Fix the above using a single access.
Also fix a couple of type annotations, to make sparse happy.
Fixes: e7cc082455 ("udp: Support for error handlers of tunnels with arbitrary destination port")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last argument of gue6_err_proto_handler() has a wrong type annotation,
fix it and make sparse happy again.
Fixes: b8a51b38e4 ("fou, fou6: ICMP error handlers for FoU and GUE")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 029a374348 ("udp6: cleanup stats accounting in recvmsg()")
I forgot to add the percpu annotation for the mib pointer. Add it, and
make sparse happy.
Fixes: 029a374348 ("udp6: cleanup stats accounting in recvmsg()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255 to
keep legacy software happy. This is similar to what was done for
ipv4 in commit 709772e6e0 ("net: Fix routing tables with
id > 255 for legacy software").
Signed-off-by: Kalash Nainwal <kalash@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
