Discard for raid4/5/6 has limitation. If discard request size is
small, we do discard for one disk, but we need calculate parity and
write parity disk. To correctly calculate parity, zero_after_discard
must be guaranteed. Even it's true, we need do discard for one disk
but write another disks, which makes the parity disks wear out
fast. This doesn't make sense. So an efficient discard for raid4/5/6
should discard all data disks and parity disks, which requires the
write pattern to be (A, A+chunk_size, A+chunk_size*2...). If A's size
is smaller than chunk_size, such pattern is almost impossible in
practice. So in this patch, I only handle the case that A's size
equals to chunk_size. That is discard request should be aligned to
stripe size and its size is multiple of stripe size.
Since we can only handle request with specific alignment and size (or
part of the request fitting stripes), we can't guarantee
zero_after_discard even zero_after_discard is true in low level
drives.
The block layer doesn't send down correctly aligned requests even
correct discard alignment is set, so I must filter out.
For raid4/5/6 parity calculation, if data is 0, parity is 0. So if
zero_after_discard is true for all disks, data is consistent after
discard. Otherwise, data might be lost. Let's consider a scenario:
discard a stripe, write data to one disk and write parity disk. The
stripe could be still inconsistent till then depending on using data
from other data disks or parity disks to calculate new parity. If the
disk is broken, we can't restore it. So in this patch, we only enable
discard support if all disks have zero_after_discard.
If discard fails in one disk, we face the similar inconsistent issue
above. The patch will make discard follow the same path as normal
write request. If discard fails, a resync will be scheduled to make
the data consistent. This isn't good to have extra writes, but data
consistency is important.
If a subsequent read/write request hits raid5 cache of a discarded
stripe, the discarded dev page should have zero filled, so the data is
consistent. This patch will always zero dev page for discarded request
stripe. This isn't optimal because discard request doesn't need such
payload. Next patch will avoid it.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When we get a read error, we arrange for raid1d to handle it.
Currently we release the reference on the device. This can result
in
conf->mirrors[read_disk].rdev
being NULL in fix_read_error, if the device happens to get removed
before the read error is handled.
So instead keep the reference until the read error has been fully
handled.
Reported-by: hank <pyu@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch replaces list_for_each_continue_rcu() with
list_for_each_entry_continue_rcu() to save a few lines
of code and allow removing list_for_each_continue_rcu().
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael Wang <wangyun@linux.vnet.ibm.com>
Signed-off-by: NeilBrown <neilb@suse.de>
There are two table arguments that can be given to a DM RAID target
that control whether the array is forced to (re)synchronize or skip
initialization: "sync" and "nosync". When "sync" is given, we set
mddev->recovery_cp to 0 in order to cause the device to resynchronize.
This is insufficient if there is a bitmap in use, because the array
will simply look at the bitmap and see that there is no recovery
necessary.
The fix is to skip over the loading of the superblocks when "sync" is
given, causing new superblocks to be written that will force the array
to go through initialization (i.e. synchronization).
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If vxlan is created and the ifindex is passed; there are two cases which
are incorrectly handled by the existing code. The ifindex could be zero
(i.e. no device) or there could be no device with that ifindex.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vxlan was trying to use postpull_rcsum to allow receive checksum
offload to work on drivers using CHECKSUM_COMPLETE method. But this
doesn't work correctly. Just force full receive checksum on received
packet.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tell upper layer protocols to allocate skb with additional headroom.
This avoids allocation and copy in local packet sends.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VXLAN bases source UDP port based on flow to help the
receiver to be able to load balance based on outer header flow.
This patch restricts the port range to the normal UDP local
ports, and allows overriding via configuration.
It also uses jhash of Ethernet header when looking at flows
with out know L3 header.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tunnelling a skb, associate it with the tunnel socket.
This allows parameters set on tunnel socket (like multicast loop
flag), to be picked up by ip_output.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Select source address for VXLAN packet based on route destination
and don't lie to route code. VXLAN is not GRE.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shift was wrong direction causing packets to hash based on
other parts of the ethernet header, not the address.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move code to find destination to a small function.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The !CONFIG_OF stubs aren't static so if multiple files include the
header with this configuration then the linker will see multiple
definitions of the stubs.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DM RAID: Fix comparison of index and quantity for "rebuild" parameter
The "rebuild" parameter takes an index argument that starts counting from
zero. The conditional used to validate the index was using '>' rather than
'>=', leaving the door open for an index value that would be 1 too large.
Reported-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Add code to validate replacement slots for RAID10 arrays
RAID10 can handle 'copies - 1' failures for each mirror group. This code
ensures the user has provided a valid array - one whose devices specified for
rebuild do not exceed the amount of redundancy available.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Move chunk of code to it's own function
The code that checks whether device replacements/rebuilds are possible given
a specific RAID type is moved to it's own function. It will further expand
when the code to check RAID10 is added. A separate function makes it easier
to read.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID10: Fix a couple potential kernel panics if RAID10 is used by dm-raid
When device-mapper uses the RAID10 personality through dm-raid.c, there is no
'gendisk' structure in mddev and some sysfs information is also not populated.
This patch avoids touching those non-existent structures.
Signed-off-by: Jonathan Brassow <jbrassow@rehdat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Some ioctls don't need to take the mutex and doing so can cause
a delay as it is held during super-block update.
So move those ioctls out of the mutex and rely on rcu locking
to ensure we don't access stale data.
Signed-off-by: NeilBrown <neilb@suse.de>
Change the thread parameter, so the thread can carry extra info. Next patch
will use it.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
It is weird to display IPv4 address in %x format, what's more,
IPv6 address is disaplayed in human-readable format too. So,
make it human-readable.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETH_ZLEN is too small for IPv6, so this default value is not
suitable.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IPv6, sizeof(struct ipv6hdr) = 40, thus the following
expression will result negative:
datalen = pkt_dev->cur_pkt_size - 14 -
sizeof(struct ipv6hdr) - sizeof(struct udphdr) -
pkt_dev->pkt_overhead;
And, the check "if (datalen < sizeof(struct pktgen_hdr))" will be
passed as "datalen" is promoted to unsigned, therefore will cause
a crash later.
This is a quick fix by checking if "datalen" is negative. The following
patch will increase the default value of 'min_pkt_size' for IPv6.
This bug should exist for a long time, so Cc -stable too.
Cc: <stable@vger.kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
queuing writes to the md thread means that all requests go through the
one processor which may not be able to keep up with very high request
rates.
So use the plugging infrastructure to submit all requests on unplug.
If a 'schedule' is needed, we fall back on the old approach of handing
the requests to the thread for it to handle.
This is nearly identical to a recent patch which provided similar
functionality to RAID1.
Signed-off-by: NeilBrown <neilb@suse.de>
This makes md raid 10 support TRIM.
If one disk supports discard and another not, or one has
discard_zero_data and another not, there could be inconsistent between
data from such disks. But this should not matter, discarded data is
useless. This will add extra copy in rebuild though.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This makes md raid 1 support TRIM.
If one disk supports discard and another not, or one has discard_zero_data and
another not, there could be inconsistent between data from such disks. But this
should not matter, discarded data is useless. This will add extra copy in rebuild
though.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
According to the comment in linear_stop function
rcu_dereference in linear_start and linear_stop functions
occurs under reconfig_mutex. The patch represents this
agreement in code and prevents lockdep complaint.
Found by Linux Driver Verification project (linuxtesting.org)
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull i2c-embedded changes from Wolfram Sang:
"The changes for i2c-embedded include:
- massive rework of the omap driver
- massive rework of the at91 driver. In fact, the old driver gets
removed; I am okay with this approach since the old driver was
depending on BROKEN and its limitations made it practically
unusable, so people used bitbanging instead. But even if there are
users, there is no platform_data or module parameter which would
need to be converted. It is just another driver doing I2C
transfers, just way better. Modifications of arch/arm/at91 related
files have proper acks from the maintainer.
- new driver for R-Car I2C
- devicetree and generic_clock conversions and fixes
- usual driver fixes and changes.
The rework patches have come a long way and lots of people have been
involved in creating/testing them. Most patches have been in
linux-next at least since 3.6-rc5. A few have been added in the last
week, I have to admit.
An unexpected (but welcome :)) peak in private life is the cause for
that. The "late" patches shouldn't cause any merge conflicts and I
will have a special eye on them during the stabilization phase. This
is an exception and I want to have the patches in place properly in
time again for the next kernels."
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (44 commits)
MXS: Implement DMA support into mxs-i2c
i2c: add Renesas R-Car I2C driver
i2c: s3c2410: use clk_prepare_enable and clk_disable_unprepare
ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints
i2c: nomadik: Add Device Tree support to the Nomadik I2C driver
i2c: algo: pca: Fix chip reset function for PCA9665
i2c: mpc: Wait for STOP to hit the bus
i2c: davinci: preparation for switch to common clock framework
omap-i2c: fix incorrect log message when using a device tree
i2c: omap: sanitize exit path
i2c: omap: switch over to autosuspend API
i2c: omap: remove unnecessary pm_runtime_suspended check
i2c: omap: switch to threaded IRQ support
i2c: omap: remove redundant status read
i2c: omap: get rid of the "complete" label
i2c: omap: resize fifos before each message
i2c: omap: simplify IRQ exit path
i2c: omap: always return IRQ_HANDLED
i2c: omap: simplify errata check
i2c: omap: bus: add a receiver flag
...
A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because firmware
no longer sets up all pin states before starting the kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was pre-agreed).
- A longer series of misc regression fixes and cleanups, warning removals,
etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vAh+
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because
firmware no longer sets up all pin states before starting the
kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was
pre-agreed).
- A longer series of misc regression fixes and cleanups, warning
removals, etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: pxa: armcore: fix PCI PIO warnings
ARM: integrator: use __iomem pointers for MMIO, part 2
ARM: assabet: fix bogus warning in get_assabet_scr (again)
ARM: shmobile: mark shmobile_init_late as __init
ARM: integrator_cp: fix build failure
ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
ARM: OMAP3: fix workaround for EMU clockdomain
arm/omap: Replace board_ref_clock with enum values
ARM: OMAP2+: remove duplicated include from board-omap3stalker.c
arch/arm/plat-omap/omap-pm-noop.c: Remove unecessary semicolon
arch/arm/mach-omap2: Remove unecessary semicolon
arch/arm/mach-omap1/devices.c: Remove unecessary semicolon
ARM/dts: omap5-evm: pinmux configuration for audio
ARM/dts: Add pinctrl driver entries for omap5
ARM/dts: omap4-panda: pinmux configuration for audio
ARM/dts: omap4-sdp: pinmux configuration for audio
ARM/dts: omap5-evm: Disable unused McBSP3
ARM/dts: omap4-sdp: Disable unused McBSP3
ARM/dts: omap4-panda: Disable unused audio IPs
ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
...
In autofs4_d_automount(), if a mount fail occurs the AUTOFS_INF_PENDING
mount pending flag is not cleared.
One effect of this is when using the "browse" option, directory entry
attributes show up with all "?"s due to the incorrect callback and
subsequent failure return (when in fact no callback should be made).
Signed-off-by: Ian Kent <ikent@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge misc fixes from Andrew Morton:
"Followups, fixes and some random stuff I found on the internet."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (11 patches)
perf: fix duplicate header inclusion
memcg, kmem: fix build error when CONFIG_INET is disabled
rtc: kconfig: fix RTC_INTF defaults connected to RTC_CLASS
rapidio: fix comment
lib/kasprintf.c: use kmalloc_track_caller() to get accurate traces for kvasprintf
rapidio: update for destination ID allocation
rapidio: update asynchronous discovery initialization
rapidio: use msleep in discovery wait
mm: compaction: fix bit ranges in {get,clear,set}_pageblock_skip()
arch/powerpc/platforms/pseries/hotplug-memory.c: section removal cleanups
arch/powerpc/platforms/pseries/hotplug-memory.c: fix section handling code
Discourage distros from enabling CONFIG_RCU_USER_QS
because it brings overhead for no benefits yet.
It's not a useful feature on its own until we can
fully run an adaptive tickless kernel.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
we want syscall_trace_leave() called on exit from any syscall;
skipping its call in case we'd done force_successful_syscall_return()
is broken...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch "drivers/video/gbefb.c: use devm_ functions" caused a
compile error.
drivers/video/gbefb.c:1159:16: error: implicit declaration of function
'devm_ioremap' [-Werror=implicit-function-declaration]
drivers/video/gbefb.c:1179:3: error: implicit declaration of function
'devm_ioremap_nocache' [-Werror=implicit-function-declaration]
Fix it by including linux/io.h which defines those functions.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Damien Cassou <damien.cassou@lifl.fr>
Missing error types, attributes, and report fields. Pad out
to 64-bytes.
Make string reporting cleaner and easier to extend in the future using
"const char *" arrays that index by either bit position, or absolute
field value.
Report the raw 64-byte error report as a sequence of u64s before the
annotated version.
Only report fields which are valid, given the context and the
attribute bits which are set.
For shutdown requests, use the local copy of the error report not the
one we just freed up back to the queue. Also, use orderly_poweroff()
just like the Domain Services shutdown request code does.
If the real-address reported is "-1" (unknown) try to disassemble the
instruction to report the effective address of the access. Only do
this in privileged mode.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull block IO update from Jens Axboe:
"Core block IO bits for 3.7. Not a huge round this time, it contains:
- First series from Kent cleaning up and generalizing bio allocation
and freeing.
- WRITE_SAME support from Martin.
- Mikulas patches to prevent O_DIRECT crashes when someone changes
the block size of a device.
- Make bio_split() work on data-less bio's (like trim/discards).
- A few other minor fixups."
Fixed up silent semantic mis-merge as per Mikulas Patocka and Andrew
Morton. It is due to the VM no longer using a prio-tree (see commit
6b2dbba8b6: "mm: replace vma prio_tree with an interval tree").
So make set_blocksize() use mapping_mapped() instead of open-coding the
internal VM knowledge that has changed.
* 'for-3.7/core' of git://git.kernel.dk/linux-block: (26 commits)
block: makes bio_split support bio without data
scatterlist: refactor the sg_nents
scatterlist: add sg_nents
fs: fix include/percpu-rwsem.h export error
percpu-rw-semaphore: fix documentation typos
fs/block_dev.c:1644:5: sparse: symbol 'blkdev_mmap' was not declared
blockdev: turn a rw semaphore into a percpu rw semaphore
Fix a crash when block device is read and block size is changed at the same time
block: fix request_queue->flags initialization
block: lift the initial queue bypass mode on blk_register_queue() instead of blk_init_allocated_queue()
block: ioctl to zero block ranges
block: Make blkdev_issue_zeroout use WRITE SAME
block: Implement support for WRITE SAME
block: Consolidate command flag and queue limit checks for merges
block: Clean up special command handling logic
block/blk-tag.c: Remove useless kfree
block: remove the duplicated setting for congestion_threshold
block: reject invalid queue attribute values
block: Add bio_clone_bioset(), bio_clone_kmalloc()
block: Consolidate bio_alloc_bioset(), bio_kmalloc()
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=arYK
-----END PGP SIGNATURE-----
Merge tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull a firewire fix from Stefan Richter:
"Fixes an old bug of the /dev/fw* ioctl ABI."
* tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: cdev: fix user memory corruption (i386 userland on amd64 kernel)
This includes a fix for PCI BAR mmaps after recent mm changes, fixing an interrupt race, and fixing a consistency bug in interrupt state when switching interrupt modes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bBhC
-----END PGP SIGNATURE-----
Merge tag 'vfio-for-v3.7-rc1' of git://github.com/awilliam/linux-vfio
Pull vfio fixes from Alex Williamson:
"This includes a fix for PCI BAR mmaps after recent mm changes, fixing
an interrupt race, and fixing a consistency bug in interrupt state
when switching interrupt modes."
* tag 'vfio-for-v3.7-rc1' of git://github.com/awilliam/linux-vfio:
vfio: Fix PCI INTx disable consistency
vfio: Move PCI INTx eventfd setting earlier
vfio: Fix PCI mmap after b3b9c293
#include <stdbool.h> somehow got duplicated on its way to linus's tree
(probably as a conflict resolution as things got sent through multiple
trees)
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit e1aab161e0 ("socket: initial cgroup code.") causes a build
error when CONFIG_INET is disabled in Linus' tree:
net/built-in.o: In function `sk_update_clone':
net/core/sock.c:1336: undefined reference to `sock_update_memcg'
sock_update_memcg() is only defined when CONFIG_INET is enabled, so fix
it by defining the dummy function without this option.
Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 6b8029fab6 ("rtc: kconfig: remove unnecessary dependencies")
removed various 'depends on RTC_CLASS' dependencies but also removed a
few 'default RTC_CLASS' statements, which actually changed default
behavior.
This resulted in the various RTC interfaces (sysfs, proc, dev) all being
disabled by default, even when RTC_CLASS is enabled:
# CONFIG_RTC_INTF_SYSFS is not set
# CONFIG_RTC_INTF_PROC is not set
# CONFIG_RTC_INTF_DEV is not set
which is different from previous behavior (all of these where enabled.)
To fix, add back the 'default RTC_CLASS' statments to each of the
RTC_INTF_* options.
I noticed this because some RTC tests started failing on my TI OMAP
platforms because /dev/rtc0 was not present anymore, even though the
driver was present and RTC_CLASS was enabled.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The resource index for the mailboxes was incorrect.
Signed-off-by: Chad Reese <kreese@caviumnetworks.com>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously kvasprintf() allocation was being done through kmalloc(),
thus producing an inaccurate trace report.
This is a common problem: in order to get accurate callsite tracing, a
lib/utils function shouldn't allocate kmalloc but instead use
kmalloc_track_caller.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Address comments provided by Andrew Morton:
https://lkml.org/lkml/2012/10/3/550
- Keeps consistent kerneldoc compatible comments style for new static
functions.
- Removes unnecessary complexity from destination ID allocation
routine.
- Uses kcalloc() for code clarity.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update discovery process initialization based on Andrew Morton's comments:
https://lkml.org/lkml/2012/10/3/552.
This update processes all enumerating mports first and schedules discovery
work after that. If the initialization routine fails to allocate resources
needed to execute discovery, it abandons discovery for all ports.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
