This gets us closer to being able to eliminate the use
of dynamic and stack based buffers, so that we can adhere
to the "no buffer addresses above 4GB" rule for PROM calls.
Signed-off-by: David S. Miller <davem@davemloft.net>
for the epson frambuffer support it's CONFIG_FB_S1D13XXX
not CONFIG_FB_S1D135XX
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
as based on http://www.picotux.com/pt200/picotux200.pdf
these board does not have such I/O
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
to be a few more concistant with the other boards
as ek is for evaluation kit and dk for development kit
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Convert the following AT91RM9200-based boards to the new-style UART
initialization:
- Ajeco 1ARM Single Board Computer
- Sperry-Sun KAFA board
- picotux 200
Remove the deprecated at91_init_serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Currently, the kprobes implementation for ARM only supports the ARM
instruction set, so it only works if CONFIG_THUMB2_KERNEL is not
enabled.
Until kprobes is updated to work with Thumb-2, turning it on will
cause horrible things to happen, so this patch disables it for now.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a
result, using these directives in code sections can result in
misaligned data words when building a Thumb-2 kernel
(CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to
assume that fundamental types of word size or above are word-
aligned when accessing them from C. If the data is not really
word-aligned, this can cause impaired performance and stray
alignment faults in some circumstances.
In general, the following rules should be applied when using
data word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned data
words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume that
fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned, this
can cause impaired performance and stray alignment faults in some
circumstances.
In general, the following rules should be applied when using data word
declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 32-bit conditional branches in Thumb-2 have a shorter range
(+/-512K) than their ARM counterparts (+/-32MB). The linker does
not currently generate trampolines to extend the range of these
Thumb-2 conditional branches, resulting in link errors when vmlinux
is sufficiently large, e.g.:
head.o:(.text+0x464): relocation truncated to fit: R_ARM_THM_JUMP19
This patch forces the longer-range, unconditional branch encoding
by use of an explicit IT instruction. The resulting branches are
triggered on the same conditions as before.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The code which makes up the zImage header intends to leave a
32-byte gap followed by a branch to the real entry point, a magic
number, and a word containing the absolute entry point address.
This gets messed up with with CONFIG_THUMB2_KERNEL, because the
size of the initial padding NOPs changes.
Instead, the header can be made fully compatible by restoring it to
ARM.
In the Thumb-2 case, we can replace the initial NOPs with a
sequence which switches to Thumb and jumps to the real entry point.
As a consequence, the zImage entry point is now always ARM, so no
special magic is needed any more for the uImage rules in the
Thumb-2 case.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some instruction operand combinations are used here which are nor
permitted in Thumb-2.
In particular, most uses of pc as an operand are disallowed in
Thumb-2, and deprecated in ARM from ARMv7 onwards.
The modified code introduced by this patch should be compatible
with all architecture versions >= v3, with or without
CONFIG_THUMB2_KERNEL.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
In this specific case, we can achieve the desired alignment by
forcing a 32-bit branch instruction using the W() macro, since the
assembler location counter is already 32-bit aligned in this case.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This change limits number of GIC-originating interrupts to the
platform maximum (defined by NR_IRQS) while still initialising
all distributor registers.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Rafael Gandolfi <kaillasse91@hotmail.fr>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
RTC clock will remain at 32KHz and powered on, there is no need for it
at this moment.
Signed-off-by: Jason Chagas <jason.chagas@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
About all options present in each file are activated
in the single file.
Signed-off-by: Eric Benard <eric@eukrea.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Dependency on (CPU_S3C2416 is not selected) was defined as "!CPU_2416",
instead of "!CPU_S3C2416". Fix it.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Enable compilation of platform devices and initialization code used in
SMDK2416 board file.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Only make swapper_pg_dir readonly and pinned when generic x86 architecture code
(which also starts on initial_page_table) switches to it. This helps ensure
that the generic setup paths work on Xen unmodified. In particular
clone_pgd_range writes directly to the destination pgd entries and is used to
initialise swapper_pg_dir so we need to ensure that it remains writeable until
the last possible moment during bring up.
This is complicated slightly by the need to avoid sharing kernel PMD entries
when running under Xen, therefore the Xen implementation must make a copy of
the kernel PMD (which is otherwise referred to by both intial_page_table and
swapper_pg_dir) before switching to swapper_pg_dir.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
PowerPC relies on IRQ-disable to guard against RCU quiecent states,
use the appropriate RCU call version.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP2+: PM/serial: hold console semaphore while OMAP UARTs are disabled
OMAP: UART: don't resume UARTs that are not enabled.
Xen will shoot all the VCPUs when we do a shutdown hypercall, so there's
no need to do it manually.
In any case it will fail because all the IPI irqs have been pulled
down by this point, so the cross-CPU calls will simply hang forever.
Until change 76fac077db the function calls
were not synchronously waited for, so this wasn't apparent. However after
that change the calls became synchronous leading to a hang on shutdown
on multi-VCPU guests.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
Cc: Alok Kataria <akataria@vmware.com>
commit 6338a6aa7c ("ARM: 6269/1: Add 'code'
parameter for hook_fault_code()") breaks CNS3xxx build:
CC arch/arm/mach-cns3xxx/pcie.o
pcie.c: In function 'cns3xxx_pcie_init':
pcie.c:373: warning: passing argument 4 of 'hook_fault_code' makes integer from pointer without a cast
pcie.c:373: error: too few arguments to function 'hook_fault_code'
This commit fixes the small issue.
Cc: stable@kernel.org [36]
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Current clk_ops doesn't support .init which
is used to select external clock on ecovec
without CONFIG_SH_CLK_CPG_LEGACY.
To solve this problem, this patch add div6_reparent_clks
to clock-sh7724.
This patch solve compile error too.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If the guest domain has been suspend/resumed or migrated, then the
system clock backing the pvclock clocksource may revert to a smaller
value (ie, can be non-monotonic across the migration/save-restore).
Make sure we zero last_value in that case so that the domain
continues to see clock updates.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
dmar, x86: Use function stubs when CONFIG_INTR_REMAP is disabled
x86-64: Fix and clean up AMD Fam10 MMCONF enabling
x86: UV: Address interrupt/IO port operation conflict
x86: Use online node real index in calulate_tbl_offset()
x86, asm: Fix binutils 2.15 build failure
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf symbols: Remove incorrect open-coded container_of()
perf record: Handle restrictive permissions in /proc/{kallsyms,modules}
x86/kprobes: Prevent kprobes to probe on save_args()
irq_work: Drop cmpxchg() result
perf: Fix owner-list vs exit
x86, hw_nmi: Move backtrace_mask declaration under ARCH_HAS_NMI_WATCHDOG
tracing: Fix recursive user stack trace
perf,hw_breakpoint: Initialize hardware api earlier
x86: Ignore trap bits on single step exceptions
tracing: Force arch_local_irq_* notrace for paravirt
tracing: Fix module use of trace_bprintk()
This leads to a Kconfig dep inversion, x86 selects PERF_EVENT (due to
a hw_breakpoint dep) but doesn't unconditionally provide
HAVE_PERF_EVENT.
(This can cause build failures on M386/M486 kernel .config's.)
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20101117222055.982965150@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In a kvm virt guests, the perf counters are not emulated. Instead they
return zero on a rdmsrl. The perf nmi handler uses the fact that crossing
a zero means the counter overflowed (for those counters that do not have
specific interrupt bits). Therefore on kvm guests, perf will swallow all
NMIs thinking the counters overflowed.
This causes problems for subsystems like kgdb which needs NMIs to do its
magic. This problem was discovered by running kgdb tests.
The solution is to write garbage into a perf counter during the
initialization and hopefully reading back the same number. On kvm
guests, the value will be read back as zero and we disable perf as
a result.
Reported-by: Jason Wessel <jason.wessel@windriver.com>
Patch-inspired-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
LKML-Reference: <1290462923-30734-1-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On each machine check all registers are revalidated. The save area for
the clock comparator however only contains the upper most seven bytes
of the former contents, if valid.
Therefore the machine check handler uses a store clock instruction to
get the current time and writes that to the clock comparator register
which in turn will generate an immediate timer interrupt.
However within the lowcore the expected time of the next timer
interrupt is stored. If the interrupt happens before that time the
handler won't be called. In turn the clock comparator won't be
reprogrammed and therefore the interrupt condition stays pending which
causes an interrupt loop until the expected time is reached.
On NOHZ machines this can result in unresponsive machines since the
time of the next expected interrupted can be a couple of days in the
future.
To fix this just revalidate the clock comparator register with the
expected value.
In addition the special handling for udelay must be changed as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch fixes following warning messages when CONFIG_PM selected.
In file included from arch/arm/mach-s5pv210/mach-smdkv210.c:34:
arch/arm/plat-samsung/include/plat/pm.h:104: warning: 'struct sys_device'
declared inside parameter list
arch/arm/plat-samsung/include/plat/pm.h:104: warning: its scope is only this
definition or declaration, which is probably not what you want
arch/arm/plat-samsung/include/plat/pm.h:105: warning: 'struct sys_device'
declared inside parameter list
In file included from arch/arm/mach-s5pv210/mach-smdkc110.c:31:
arch/arm/plat-samsung/include/plat/pm.h:104: warning: 'struct sys_device'
declared inside parameter list
arch/arm/plat-samsung/include/plat/pm.h:104: warning: its scope is only this
definition or declaration, which is probably not what you want
arch/arm/plat-samsung/include/plat/pm.h:105: warning: 'struct sys_device'
declared inside parameter list
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The UART3 submask should be 0x7 (SUBSRCPND[26:24]).
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
IRQ_S3C2443_UART3 is being used as the base when it should actually
be IRQ_S3C2443_RX3 on S3C2443 and S3C2416 for the UART3.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Don't rewrite clock config in UCON preconfigured by
bootloader. No need to set 10th bit in UCON because
[11:10] 2'b00 means source clock is PCLK too.
If set, console does not work if bootloader
has preconfigured [11:10] with 2'b00.
If not set, console works with any bootloader
config value (2'bxx).
More information about clock setup in UCON is available
in "S3C6410X RISC Microprocessor User's Manual,
Revision 1.20" p. 31-13 (Chapter 31.6.2
UART CONTROL REGISTER).
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Replace in s3c_gpio_cfgpull with s3c_gpio_setpull.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The console semaphore must be held while the OMAP UART devices are
disabled, lest a console write cause an ARM abort (and a kernel crash)
when the underlying console device is inaccessible. These crashes
only occur when the console is on one of the OMAP internal serial
ports.
While this problem has been latent in the PM idle loop for some time,
the crash was not triggerable with an unmodified kernel until commit
6f251e9db1 ("OMAP: UART: omap_device
conversions, remove implicit 8520 assumptions"). After this patch, a
console write often occurs after the console UART has been disabled in
the idle loop, crashing the system. Several users have encountered
this bug:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg38396.htmlhttp://www.mail-archive.com/linux-omap@vger.kernel.org/msg36602.html
The same commit also introduced new code that disabled the UARTs
during init, in omap_serial_init_port(). The kernel will also crash
in this code when earlyconsole and extra debugging is enabled:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg36411.html
The minimal fix for the -rc series is to hold the console semaphore
while the OMAP UARTs are disabled. This is a somewhat overbroad fix,
since the console may not be located on an OMAP UART, as is the case
with the GPMC UART on Zoom3. While it is technically possible to
determine which devices the console or earlyconsole is actually
running on, it is not a trivial problem to solve, and the code to do
so is not really appropriate for the -rc series.
The right long-term fix is to ensure that no code outside of the OMAP
serial driver can disable an OMAP UART. As I understand it, code to
implement this is under development by TI.
This patch is a collaboration between Paul Walmsley <paul@pwsan.com>
and Tony Lindgren <tony@atomide.com>. Thanks to Ming Lei
<tom.leiming@gmail.com> and Pramod <pramod.gurav@ti.com> for their
feedback on earlier versions of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Pramod <pramod.gurav@ti.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Add additional check to omap_uart_resume_idle() so that only
enabled (specifically, idle-enabled) UARTs are allowed to resume.
This matches the existing check in prepare idle.
Without this patch, the system will hang if a board is
configured to register only some uarts instead of all of
them and PM is enabled.
Cc: Govindraj R. <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: fix memchr() not to dereference memory for zero length
arch/tile: make glibc's sysconf(_SC_NPROCESSORS_CONF) work correctly
arch/tile: fix rwlock so would-be write lockers don't block new readers
* 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
pci root complex: support for tile architecture
drivers/net/tile/: on-chip network drivers for the tile architecture
MAINTAINERS: add drivers/char/hvc_tile.c as maintained by tile
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: clkfwk: Build fix for non-legacy CPG changes.
sh: Use GCC __builtin_prefetch() to implement prefetch().
sh: fix vsyscall compilation due to .eh_frame issue
sh: avoid to flush all cache in sys_cacheflush
sh: clkfwk: Disable init clk op for non-legacy clocks.
sh: clkfwk: Kill off now unused algo_id in set_rate op.
sh: clkfwk: Kill off unused clk_set_rate_ex().
When compiling arch/x86/kernel/early_printk_mrst.c with i386
allmodconfig, gcc-4.1.0 generates an out-of-line copy of
__set_fixmap_offset() which contains a reference to
__this_fixmap_does_not_exist which the compiler cannot elide.
Marking __set_fixmap_offset() as __always_inline prevents this.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Feng Tang <feng.tang@intel.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Disable the winch irq early to make sure we don't take an interrupt part
way through the freeing of the handler data, resulting in a crash on
shutdown:
winch_interrupt : read failed, errno = 9
fd 13 is losing SIGWINCH support
------------[ cut here ]------------
WARNING: at lib/list_debug.c:48 list_del+0xc6/0x100()
list_del corruption, next is LIST_POISON1 (00100100)
082578c8: [<081fd77f>] dump_stack+0x22/0x24
082578e0: [<0807a18a>] warn_slowpath_common+0x5a/0x80
08257908: [<0807a23e>] warn_slowpath_fmt+0x2e/0x30
08257920: [<08172196>] list_del+0xc6/0x100
08257940: [<08060244>] free_winch+0x14/0x80
08257958: [<080606fb>] winch_interrupt+0xdb/0xe0
08257978: [<080a65b5>] handle_IRQ_event+0x35/0xe0
08257998: [<080a8717>] handle_edge_irq+0xb7/0x170
082579bc: [<08059bc4>] do_IRQ+0x34/0x50
082579d4: [<08059e1b>] sigio_handler+0x5b/0x80
082579ec: [<0806a374>] sig_handler_common+0x44/0xb0
08257a68: [<0806a538>] sig_handler+0x38/0x50
08257a78: [<0806a77c>] handle_signal+0x5c/0xa0
08257a9c: [<0806be28>] hard_handler+0x18/0x20
08257aac: [<00c14400>] 0xc14400
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The find_next_bit, find_first_bit, find_next_zero_bit
and find_first_zero_bit functions were not properly
clamping to the maxbit argument at the bit level. They
were instead only checking maxbit at the byte level.
To fix this, add a compare and a conditional move
instruction to the end of the common bit-within-the-
byte code used by all the functions and be sure not to
clobber the maxbit argument before it is used.
Cc: <stable@kernel.org>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: James Jones <jajones@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This change fixes a bug that memchr() will read the first word
of the source even if the length is zero. Ironically, the code
was originally written with a test to avoid exactly this problem,
but to make the code conform to Linux coding standards with all
declarations preceding all statements, the first load from memory
was moved up above that test as the initial value for a variable.
The change just moves all the variable declarations to the top
of the file, with no initializers, so that the test can also be
at the top of the file.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
glibc assumes that it can count /sys/devices/system/cpu/cpu* to get
the number of configured cpus. For this to be valid on tile, we need
to generate a "cpu" entry for all cpus, including the ones that are
not currently allocated for Linux's use.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This change enables PCI root complex support for TILEPro. Unlike
TILE-Gx, TILEPro has no support for memory-mapped I/O, so the PCI
support consists of hypervisor upcalls for PIO, DMA, etc. However,
the performance is fine for the devices we have tested with so far
(1Gb Ethernet, SATA, etc.).
The <asm/io.h> header was tweaked to be a little bit more aggressive
about disabling attempts to map/unmap IO port space. The hacky
<asm/pci-bridge.h> header was rolled into the <asm/pci.h> header
and the result was simplified. Both of the latter two headers were
preliminary versions not meant for release before now - oh well.
There is one quirk for our TILEmpower platform, which accidentally
negotiates up to 5GT and needs to be kicked down to 2.5GT.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This change adds the first network driver for the tile architecture,
supporting the on-chip XGBE and GBE shims.
The infrastructure is present for the TILE-Gx networking drivers (another
three source files in the new directory) but for now the the actual
tilegx sources are waiting on releasing hardware to initial customers.
Note that arch/tile/include/hv/* are "upstream" headers from the
Tilera hypervisor and will probably benefit less from LKML review.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Only make swapper_pg_dir readonly and pinned when generic x86 architecture code
(which also starts on initial_page_table) switches to it. This helps ensure
that the generic setup paths work on Xen unmodified. In particular
clone_pgd_range writes directly to the destination pgd entries and is used to
initialise swapper_pg_dir so we need to ensure that it remains writeable until
the last possible moment during bring up.
This is complicated slightly by the need to avoid sharing kernel PMD entries
when running under Xen, therefore the Xen implementation must make a copy of
the kernel PMD (which is otherwise referred to by both intial_page_table and
swapper_pg_dir) before switching to swapper_pg_dir.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The PLLC2 clock was utilizing the same sort of enable/disable without
regard to usecount approach that the FSIDIV clock was when being used as
a PLL pass-through. This forces the enable/disable through the clock
framework, which now prevents the clock from being ripped out or modified
underneath users that have an existing handle on it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current AP4 FSI didn't use set_rate for ak4642,
and used dummy rate when init.
And FSI driver was modified to always call set_rate.
The user which are using FSI set_rate is only AP4 now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current AP4 FSI set_rate function used bogus clock process
which didn't care enable/disable and clk->usecound.
To solve this issue, this patch also modify FSI driver to call
set_rate with enough options.
This patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current FSIDIV clock framework had bogus disable.
This patch remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (41 commits)
ALSA: hda - Identify more variants for ALC269
ALSA: hda - Fix wrong ALC269 variant check
ALSA: hda - Enable jack sense for Thinkpad Edge 11
ALSA: Revert "ALSA: hda - Fix switching between dmic and mic using the same mux on IDT/STAC"
ALSA: hda - Fixed ALC887-VD initial error
ALSA: atmel - Fix the return value in error path
ALSA: hda: Use hp-laptop quirk to enable headphones automute for Asus A52J
ALSA: snd-atmel-abdac: test wrong variable
ALSA: azt3328: period bug fix (for PA), add missing ACK on stop timer
ALSA: hda: Add Samsung R720 SSID for subwoofer pin fixup
ALSA: sound/pci/asihpi/hpioctl.c: Remove unnecessary casts of pci_get_drvdata
ALSA: sound/core/pcm_lib.c: Remove unnecessary semicolons
ALSA: sound/ppc: Use printf extension %pR for struct resource
ALSA: ac97: Apply quirk for Dell Latitude D610 binding Master and Headphone controls
ASoC: uda134x - set reg_cache_default to uda134x_reg
ASoC: Add support for MAX98089 CODEC
ASoC: davinci: fixes for multi-component
ASoC: Fix register cache setup WM8994 for multi-component
ASoC: Fix dapm_seq_compare() for multi-component
ASoC: RX1950: Fix hw_params function
...
* 'upstream/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen: (23 commits)
xen/events: Use PIRQ instead of GSI value when unmapping MSI/MSI-X irqs.
xen: set IO permission early (before early_cpu_init())
xen: re-enable boot-time ballooning
xen/balloon: make sure we only include remaining extra ram
xen/balloon: the balloon_lock is useless
xen: add extra pages to balloon
xen: make evtchn's name less generic
xen/evtchn: the evtchn device is non-seekable
Revert "xen/privcmd: create address space to allow writable mmaps"
xen/events: use locked set|clear_bit() for cpu_evtchn_mask
xen/evtchn: clear secondary CPUs' cpu_evtchn_mask[] after restore
xen/xenfs: update xenfs_mount for new prototype
xen: fix header export to userspace
xen: implement XENMEM_machphys_mapping
xen: set vma flag VM_PFNMAP in the privcmd mmap file_op
xen: xenfs: privcmd: check put_user() return code
xen/evtchn: add missing static
xen/evtchn: Fix name of Xen event-channel device
xen/evtchn: don't do unbind_from_irqhandler under spinlock
xen/evtchn: remove spurious barrier
...
init_mm used at kernel/sched.c:idle_task_exit() has spin_lock
(init_mm.context.id_lock) that is not initialized when spin_lock/unlock
is called at an ARM machine. Note that mm_struct.context.id_lock is
usually initialized except for the instance of init_mm at
linux/arch/arm/mm/context.c
Not initializing this spinlock incurs "BUG: pinlock bad magic"
warning when spinlock debug is enabled. We have observed such
instances when testing PM in S5PC210 machines.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adding KERN_WARNING in the middle of strings now produces those tokens
in the output, rather than accepting the level as was once the case.
Fix this in the one reported case. There might be more...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We just need the idle loop to drop into safe_halt, which default_idle()
is perfectly capable of doing. There's no need to duplicate it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Make sure that extra_pages is added for all E820_RAM regions beyond
mem_end - completely excluded regions as well as the remains of partially
included regions.
Also makes sure the extra region is not unnecessarily high, and simplifies
the logic to decide which regions should be added.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
* upstream/core:
xen/events: Use PIRQ instead of GSI value when unmapping MSI/MSI-X irqs.
xen: set IO permission early (before early_cpu_init())
xen: re-enable boot-time ballooning
xen/balloon: make sure we only include remaining extra ram
xen/balloon: the balloon_lock is useless
xen: add extra pages to balloon
xen/events: use locked set|clear_bit() for cpu_evtchn_mask
xen/evtchn: clear secondary CPUs' cpu_evtchn_mask[] after restore
xen: implement XENMEM_machphys_mapping
* upstream/xenfs:
Revert "xen/privcmd: create address space to allow writable mmaps"
xen/xenfs: update xenfs_mount for new prototype
xen: fix header export to userspace
xen: set vma flag VM_PFNMAP in the privcmd mmap file_op
xen: xenfs: privcmd: check put_user() return code
* upstream/evtchn:
xen: make evtchn's name less generic
xen/evtchn: the evtchn device is non-seekable
xen/evtchn: add missing static
xen/evtchn: Fix name of Xen event-channel device
xen/evtchn: don't do unbind_from_irqhandler under spinlock
xen/evtchn: remove spurious barrier
xen/evtchn: ports start enabled
xen/evtchn: dynamically allocate port_user array
xen/evtchn: track enabled state for each port
We now:
* check for a v3 controller before setting 8-bit bus width
* offer a callback for platform code to switch to 8-bit mode, which
allows non-v3 controllers to support it
* rely on mmc->caps |= MMC_CAP_8_BIT_DATA; in platform code to specify
that the board designers have indeed brought out all the pins for
8-bit to the slot.
We were previously relying only on whether the *controller* supported
8-bit, which doesn't tell us anything about the pin configuration in
the board design.
This fixes the MMC card regression reported by Maxim Levitsky here:
http://thread.gmane.org/gmane.linux.kernel.mmc/4336
by no longer assuming that 8-bit works by default.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is based off "xen dom0: Set up basic IO permissions for dom0."
by Juan Quintela <quintela@redhat.com>.
On AMD machines when we boot the kernel as Domain 0 we get this nasty:
mapping kernel into physical memory
Xen: setup ISA identity maps
about to get started...
(XEN) traps.c:475:d0 Unhandled general protection fault fault/trap [#13] on VCPU 0 [ec=0000]
(XEN) domain_crash_sync called from entry.S
(XEN) Domain 0 (vcpu#0) crashed on cpu#0:
(XEN) ----[ Xen-4.1-101116 x86_64 debug=y Not tainted ]----
(XEN) CPU: 0
(XEN) RIP: e033:[<ffffffff8130271b>]
(XEN) RFLAGS: 0000000000000282 EM: 1 CONTEXT: pv guest
(XEN) rax: 000000008000c068 rbx: ffffffff8186c680 rcx: 0000000000000068
(XEN) rdx: 0000000000000cf8 rsi: 000000000000c000 rdi: 0000000000000000
(XEN) rbp: ffffffff81801e98 rsp: ffffffff81801e50 r8: ffffffff81801eac
(XEN) r9: ffffffff81801ea8 r10: ffffffff81801eb4 r11: 00000000ffffffff
(XEN) r12: ffffffff8186c694 r13: ffffffff81801f90 r14: ffffffffffffffff
(XEN) r15: 0000000000000000 cr0: 000000008005003b cr4: 00000000000006f0
(XEN) cr3: 0000000221803000 cr2: 0000000000000000
(XEN) ds: 0000 es: 0000 fs: 0000 gs: 0000 ss: e02b cs: e033
(XEN) Guest stack trace from rsp=ffffffff81801e50:
RIP points to read_pci_config() function.
The issue is that we don't set IO permissions for the Linux kernel early enough.
The call sequence used to be:
xen_start_kernel()
x86_init.oem.arch_setup = xen_setup_arch;
setup_arch:
- early_cpu_init
- early_init_amd
- read_pci_config
- x86_init.oem.arch_setup [ xen_arch_setup ]
- set IO permissions.
We need to set the IO permissions earlier on, which this patch does.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The .stack section doesn't contain any contents, and doesn't require
initialization either. Rather than marking the output section with
'NOLOAD' but still having it exist in the object files, mark it with
%nobits which avoids the assembler marking the section with 'CONTENTS'.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 8b592783 added a Thumb-2 variant of usracc which, when it is
called with \rept=2, calls usraccoff once with an offset of 0 and
secondly with a hard-coded offset of 4 in order to avoid incrementing
the pointer again. If \inc != 4 then we will store the data to the wrong
offset from \ptr. Luckily, the only caller that passes \rept=2 to this
function is __clear_user so we haven't been actively corrupting user data.
This patch fixes usracc to pass \inc instead of #4 to usraccoff
when it is called a second time.
Cc: <stable@kernel.org>
Reported-by: Tony Thompson <tony.thompson@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current implementation of sched_clock() for the Nomadik
family is based on the clock source that will wrap around without
any compensation. Currently on the Ux500 after 1030 seconds.
Utilize cnt32_to_63 to expand the sched_clock() counter to 63
bits and introduce a keepwarm() timer to assure that sched clock
and this cnt32_to_63 is called atleast once every half period.
When I print out the actual wrap-around time, and using
a year (3600*24*365 seconds) as minumum wrap limit I get an
actual wrap-around of:
sched_clock: using 55 bits @ 8333125 Hz wrap in 416 days
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 7c63984b86 (ARM: do not define VMALLOC_END relative to PAGE_OFFSET)
changed VMALLOC_END to be an explicit value. Before this, it was
relative to PAGE_OFFSET and therefore converted to unsigned long
as PAGE_OFFSET is an unsigned long. This introduced the following
build warning. Fix this by changing the explicit defines of
VMALLOC_END to be unsigned long.
CC arch/arm/mm/init.o
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:606: warning: format '%08lx' expects type 'long unsigned int', but argument 12 has type 'unsigned int'
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Uwe Kleine-K <u.kleine-koenig@pengutronix.dee>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This change updates the ux500 specific outer cache code to use
the new *_relaxed() I/O accessors.
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the compiler to better optimize the page table walking code
by avoiding over-complex pmd_addr_end() calculations. These
calculations prevent the compiler spotting that we'll never iterate
over the PMD table, causing it to create double nested loops where
a single loop will do.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the balloon driver doesn't stumble over non-RAM pages, we
can enable the extra space for ballooning.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdb,ppc: Fix regression in evr register handling
kgdb,x86: fix regression in detach handling
kdb: fix crash when KDB_BASE_CMD_MAX is exceeded
kdb: fix memory leak in kdb_main.c
Candidate memory ranges were not calculated properly (start
addresses got needlessly rounded down, and end addresses didn't
get rounded up at all), address comparison for secondary CPUs
was done on only part of the address, and disabled status wasn't
tracked properly.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <4CE24DF40200007800022737@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Prevent kprobes to probe on save_args() since this function
will be called from breakpoint exception handler. That will
cause infinit loop on breakpoint handling.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: 2nddept-manager@sdl.hitachi.co.jp
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
LKML-Reference: <20101118101655.2779.2816.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch for SGI UV systems addresses a problem whereby
interrupt transactions being looped back from a local IOH,
through the hub to a local CPU can (erroneously) conflict with
IO port operations and other transactions.
To workaound this we set a high bit in the APIC IDs used for
interrupts. This bit appears to be ignored by the sockets, but
it avoids the conflict in the hub.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
LKML-Reference: <20101116222352.GA8155@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
___
arch/x86/include/asm/uv/uv_hub.h | 4 ++++
arch/x86/include/asm/uv/uv_mmrs.h | 19 ++++++++++++++++++-
arch/x86/kernel/apic/x2apic_uv_x.c | 25 +++++++++++++++++++++++--
arch/x86/platform/uv/tlb_uv.c | 2 +-
arch/x86/platform/uv/uv_time.c | 4 +++-
5 files changed, 49 insertions(+), 5 deletions(-)
Found a NUMA system that doesn't have RAM installed at the first
socket which hangs while executing init scripts.
bisected it to:
| commit 9329672021
| Author: Shaohua Li <shaohua.li@intel.com>
| Date: Wed Oct 20 11:07:03 2010 +0800
|
| x86: Spread tlb flush vector between nodes
It turns out when first socket is not online it could have cpus on
node1 tlb_offset set to bigger than NUM_INVALIDATE_TLB_VECTORS.
That could affect systems like 4 sockets, but socket 2 doesn't
have installed, sockets 3 will get too big tlb_offset.
Need to use real online node idx.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <4CDEDE59.40603@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add parentheses around one pushl_cfi argument.
Commit df5d1874 "x86: Use {push,pop}{l,q}_cfi in more places"
caused GNU assembler 2.15 (Debian Sarge) to fail. It is still
failing as of commit 07bd8516 "x86, asm: Restore parentheses
around one pushl_cfi argument". This patch solves build failure
with GNU assembler 2.15.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Jan Beulich <jbeulich@novell.com>
Cc: heukelum@fastmail.fm
Cc: hpa@linux.intel.com
LKML-Reference: <201011160445.oAG4jGif079860@www262.sakura.ne.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
backtrace_mask has been used under the code context of
ARCH_HAS_NMI_WATCHDOG. So put it into that context.
We were warned by the following warning:
arch/x86/kernel/apic/hw_nmi.c:21: warning: ‘backtrace_mask’ defined but not used
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
LKML-Reference: <1289573455-3410-2-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix a MSTP assignment problem in the sh7372 clock
framework code. The USB drivers should attach to
MSTP322 not MSTP33 where IIC1 is located.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
GCC's __builtin_prefetch() was introduced a long time ago, all
supported GCC versions have it. So this patch is to use it for
implementing the prefetch on SH2A and SH4.
The current prefetch implementation is almost equivalent with
__builtin_prefetch.
The third parameter in the __builtin_prefetch is the locality
that it's not supported on SH architectures. It has been set
to three and it should be verified if it's suitable for SH2A
as well. I didn't test on this architecture.
The builtin usage should be more efficient that an __asm__
because less barriers, and because the compiler doesn't see the
inst as a "black box" allowing better code generation.
This has been already done on other architectures (see the commit:
0453fb3c52).
Many thanks to Christian Bruel <christain.bruel@st.com> for his
support on evaluate the impact of the gcc built-in on SH4 arch.
No regressions found while testing with LMbench on STLinux targets.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The commit 5e3d20a remove bkl from startup code so setup_arch() it isn't called
with bkl held anymore. Update the comment on top of that function.
Fix also a typo.
This work was supported by a hardware donation from the CE Linux Forum.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We were seeing oops like the following when we did an rmmod on a module:
Unable to handle kernel paging request for instruction fetch
Faulting instruction address: 0x8000000000008010
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=2 P5020 DS
last sysfs file: /sys/devices/qman-portals.2/qman-pool.9/uevent
Modules linked in: qman_tester(-)
NIP: 8000000000008010 LR: c000000000074858 CTR: 8000000000008010
REGS: c00000002e29bab0 TRAP: 0400 Not tainted
(2.6.34.6-00744-g2d21f14)
MSR: 0000000080029000 <EE,ME,CE> CR: 24000448 XER: 00000000
TASK = c00000007a8be600[4987] 'rmmod' THREAD: c00000002e298000 CPU: 1
GPR00: 8000000000008010 c00000002e29bd30 8000000000012798 c00000000035fb28
GPR04: 0000000000000002 0000000000000002 0000000024022428 c000000000009108
GPR08: fffffffffffffffe 800000000000a618 c0000000003c13c8 0000000000000000
GPR12: 0000000022000444 c00000000fffed00 0000000000000000 0000000000000000
GPR16: 00000000100c0000 0000000000000000 00000000100dabc8 0000000010099688
GPR20: 0000000000000000 00000000100cfc28 0000000000000000 0000000010011a44
GPR24: 00000000100017b2 0000000000000000 0000000000000000 0000000000000880
GPR28: c00000000035fb28 800000000000a7b8 c000000000376d80 c0000000003cce50
NIP [8000000000008010] .test_exit+0x0/0x10 [qman_tester]
LR [c000000000074858] .SyS_delete_module+0x1f8/0x2f0
Call Trace:
[c00000002e29bd30] [c0000000000748b4] .SyS_delete_module+0x254/0x2f0 (unreliable)
[c00000002e29be30] [c000000000000580] syscall_exit+0x0/0x2c
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
38600000 4e800020 60000000 60000000 <4e800020> 60000000 60000000 60000000
---[ end trace 4f57124939a84dc8 ]---
This appears to be due to checking the wrong permission bits in the
instruction_tlb_miss handling if the address that faulted was in vmalloc
space. We need to look at the supervisor execute (_PAGE_BAP_SX) bit and
not the user bit (_PAGE_BAP_UX/_PAGE_EXEC).
Also removed a branch level since it did not appear to be used.
Reported-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In:
powerpc/mm: Fix pgtable cache cleanup with CONFIG_PPC_SUBPAGE_PROT
commit d28513bc7f
Author: David Gibson <david@gibson.dropbear.id.au>
subpage_protection() was changed to to take an mm rather a pgdir but it
didn't change calling site in hashpage_preload(). The change wasn't
noticed at compile time since hashpage_preload() used a void* as the
parameter to subpage_protection().
This is obviously wrong and can trigger the following crash when
CONFIG_SLAB, CONFIG_DEBUG_SLAB, CONFIG_PPC_64K_PAGES
CONFIG_PPC_SUBPAGE_PROT are enabled.
Freeing unused kernel memory: 704k freed
Unable to handle kernel paging request for data at address 0x6b6b6b6b6b6c49b7
Faulting instruction address: 0xc0000000000410f4
cpu 0x2: Vector: 300 (Data Access) at [c00000004233f590]
pc: c0000000000410f4: .hash_preload+0x258/0x338
lr: c000000000041054: .hash_preload+0x1b8/0x338
sp: c00000004233f810
msr: 8000000000009032
dar: 6b6b6b6b6b6c49b7
dsisr: 40000000
current = 0xc00000007e2c0070
paca = 0xc000000007fe0500
pid = 1, comm = init
enter ? for help
[c00000004233f810] c000000000041020 .hash_preload+0x184/0x338 (unreliable)
[c00000004233f8f0] c00000000003ed98 .update_mmu_cache+0xb0/0xd0
[c00000004233f990] c000000000157754 .__do_fault+0x48c/0x5dc
[c00000004233faa0] c000000000158fd0 .handle_mm_fault+0x508/0xa8c
[c00000004233fb90] c0000000006acdd4 .do_page_fault+0x428/0x6ac
[c00000004233fe30] c000000000005260 handle_page_fault+0x20/0x74
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit ffe8018c34 of the -mm tree
fixes the initramfs size calculation for e.g. s390 but breaks it
for 32bit architectures which do not define CONFIG_32BIT.
This patch fix the problem for PPC32 which will elsewise end up
with a __initramfs_size of 0.
Signed-off-by: Kerstin Jonsson <kerstin.jonsson@ericsson.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/mm/tlb_nohash.c: In function 'setup_initial_memory_limit':
arch/powerpc/mm/tlb_nohash.c:588:29: error: 'ppc64_memblock_base' undeclared (first use in this function)
arch/powerpc/mm/tlb_nohash.c:588:29: note: each undeclared identifier is reported only once for each function it appears in
Due to a copy/paste typo with the following commit:
commit cd3db0c4ca
Author: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Date: Tue Jul 6 15:39:02 2010 -0700
memblock: Remove rmo_size, burry it in arch/powerpc where it belongs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
EEH and pci_dlpar #undef DEBUG, but I think they were added before the
ability to control this from Kconfig. It's really annoying to only get
some of the debug messages from these files. Leave the lpar.c #undef
alone as it produces so much output as to make the kernel unusable.
Update the Kconfig text to indicate this particular quirk :)
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The code is missing a fix that went into the main kernel variant
(we should try to share that code again at some stage)
Reported-by: Albert Cahalan <acahalan@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We now use load_gs_index() to load gs safely; unfortunately this also
changes MSR_KERNEL_GS_BASE, which we managed separately. This resulted
in confusion and breakage running 32-bit host userspace on a 64-bit kernel.
Fix by
- saving guest MSR_KERNEL_GS_BASE before we we reload the host's gs
- doing the host save/load unconditionally, instead of only when in guest
long mode
Things can be cleaned up further, but this is the minmal fix for now.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If fs or gs refer to the ldt, they must be reloaded after the ldt. Reorder
the code to that effect.
Userspace code that uses the ldt with kvm is nonexistent, so this doesn't fix
a user-visible bug.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Commit ff10b88b5a (kgdb,ppc: Individual
register get/set for ppc) introduced a problem where memcpy was used
incorrectly to read and write the evr registers with a kernel that
has:
CONFIG_FSL_BOOKE=y
CONFIG_SPE=y
CONFIG_KGDB=y
This patch also fixes the following compilation problems:
arch/powerpc/kernel/kgdb.c: In function 'dbg_get_reg':
arch/powerpc/kernel/kgdb.c:341: error: passing argument 2 of 'memcpy' makes pointer from integer without a cast
arch/powerpc/kernel/kgdb.c: In function 'dbg_set_reg':
arch/powerpc/kernel/kgdb.c:366: error: passing argument 1 of 'memcpy' makes pointer from integer without a cast
[jason.wessel@windriver.com: Remove void * casts and fix patch header]
Reported-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: linuxppc-dev@lists.ozlabs.org
The fix from ba773f7c51
(x86,kgdb: Fix hw breakpoint regression) was not entirely complete.
The kgdb_remove_all_hw_break() function also needs to call the
hw_break_release_slot() or else a breakpoint can get activated again
after the debugger has detached.
The kgdb test suite exposes the behavior in the form of either a hang
or repetitive failure. The kernel config that exposes the problem
contains all of the following:
CONFIG_DEBUG_RODATA=y
CONFIG_KGDB_TESTS=y
CONFIG_KGDB_TESTS_ON_BOOT=y
CONFIG_KGDB_TESTS_BOOT_STRING="V1F100"
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Tested-by: Frederic Weisbecker <fweisbec@gmail.com>
Multi-component commit f0fba2ad broke a few things which this patch should
fix. Tested on the DM355 EVM. I've been as careful as I can, but it would be
good if those with access to other Davinci boards could test.
--
The multi-component commit put the initialisation of
snd_soc_dai.[capture|playback]_dma_data into snd_soc_dai_ops.hw_params of the
McBSP, McASP & VCIF drivers (davinci-i2s.c, davinci-mcasp.c & davinci-vcif.c).
The initialisation had to be moved from the probe function in these drivers
because davinci_*_dai changed from snd_soc_dai to snd_soc_dai_driver.
Unfortunately, the DMA params pointer is needed by davinci_pcm_open (in
davinci-pcm.c) before hw_params is called. I have moved the initialisation to
a new snd_soc_dai_ops.startup function in each of these drivers. This fix
indicates that all platforms that use davinci-pcm must have been broken and
need to test with this fix.
--
The multi-component commit also changed the McBSP driver name from
"davinci-asp" to "davinci-i2s" in davinci-i2s.c without updating the board
level references to the driver name. This change is understandable, as there
is a similarly named "davinci-mcasp" driver in davinci-mcasp.c.
There is probably no 'correct' name for this driver. The DM6446 datasheet
calls it the "ASP" and describes it as a "specialised McBSP". The DM355
datasheet calls it the "ASP" and describes it as a "specialised ASP". The
DM365 datasheet calls it the "McBSP". Rather than fix this problem by
reverting to "davinci-asp", I've elected to avoid future confusion with the
"davinci-mcasp" driver by changing it to "davinci-mcbsp", which is also
consistent with the names of the functions in the driver. There are other
fixes required, so it was never going to be as simple as a revert anyway.
--
The DM365 only has one McBSP port (of the McBSP platforms, only the DM355 has
2 ports), so I've changed the the id of the platform_device from 0 to -1.
--
In davinci-evm.c, the DM6446 EVM can no longer share a snd_soc_dai_link
structure with the DM355 EVM as they use different cpu DAI names (the DM355
has 2 ports and the EVM uses the second port, but the DM6446 only has 1 port).
This also means that the 2 boards need different snd_soc_card structures.
--
The codec_name entries in davinci-evm.c didn't match the i2c ids in the board
files. I have only checked and fixed the details of the names used for the
McBSP based platforms. Someone with a McASP based platform (eg DA8xx) should
check the others.
Signed-off-by: Chris Paulson-Ellis <chris@edesix.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the following error obtained when
compile the Kernel with the VSYSCALL support enabled:
SYSCALL arch/sh/kernel/vsyscall/vsyscall-trapa.so
sh4-linux/bin/ld: error in arch/sh/kernel/vsyscall/vsyscall-trapa.o(.eh_frame);
no .eh_frame_hdr table will be created.
AS arch/sh/kernel/vsyscall/vsyscall-syscall.o
Disassembling the vsyscall-trapa.o code, with this fix applied,
we get the __kernel_vsyscall symbol defined; otherwise it was
missing.
Disassembly of section .text:
00000000 <__kernel_vsyscall>:
0: 10 00 .word 0x0010
2: 00 00 .word 0x0000
[snip]
0000040 <__kernel_sigreturn>:
40: 05 93 mov.w 4e <__kernel_sigreturn+0xe>,r3 ! 77
42: 10 c3 trapa #16
[snip]
00000060 <__kernel_rt_sigreturn>:
60: 05 93 mov.w 6e <__kernel_rt_sigreturn+0xe>,r3 ! ad
62: 10 c3 trapa #16
[snip]
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Calling sys_cacheflush with ICACHE we can direclty flush
the icache without invoking the flush_cache_all function.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* commit 'v2.6.37-rc2': (10093 commits)
Linux 2.6.37-rc2
capabilities/syslog: open code cap_syslog logic to fix build failure
i2c: Sanity checks on adapter registration
i2c: Mark i2c_adapter.id as deprecated
i2c: Drivers shouldn't include <linux/i2c-id.h>
i2c: Delete unused adapter IDs
i2c: Remove obsolete cleanup for clientdata
include/linux/kernel.h: Move logging bits to include/linux/printk.h
Fix gcc 4.5.1 miscompiling drivers/char/i8k.c (again)
hwmon: (w83795) Check for BEEP pin availability
hwmon: (w83795) Clear intrusion alarm immediately
hwmon: (w83795) Read the intrusion state properly
hwmon: (w83795) Print the actual temperature channels as sources
hwmon: (w83795) List all usable temperature sources
hwmon: (w83795) Expose fan control method
hwmon: (w83795) Fix fan control mode attributes
hwmon: (lm95241) Check validity of input values
hwmon: Change mail address of Hans J. Koch
PCI: sysfs: fix printk warnings
GFS2: Fix inode deallocation race
...
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] kprobes: Fix the return address of multiple kretprobes
[S390] kprobes: disable interrupts throughout
[S390] ftrace: build without frame pointers on s390
[S390] mm: add devmem_is_allowed() for STRICT_DEVMEM checking
[S390] vmlogrdr: purge after recording is switched off
[S390] cio: fix incorrect ccw_device_init_count
[S390] tape: add medium state notifications
[S390] fix get_user_pages_fast
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
arm: omap1: devices: need to return with a value
OMAP1: camera.h: add missing include
omap: dma: Add read-back to DMA interrupt handler to avoid spuriousinterrupts
OMAP2: Devkit8000: Fix mmc regulator failure
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: sysfs: fix printk warnings
PCI: fix pci_bus_alloc_resource() hang, prefer positive decode
PCI: read current power state at enable time
PCI: fix size checks for mmap() on /proc/bus/pci files
x86/PCI: coalesce overlapping host bridge windows
PCI hotplug: ibmphp: Add check to prevent reading beyond mapped area
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: intc: Fix up build failure introduced by radix tree changes.
MAINTAINERS: update the sh git tree entry.
sh: clkfwk: fix up compiler warnings.
sh: intc: Fix up initializers for gcc 4.5.
rtc: rtc-sh - fix a memory leak
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: mach-shmobile: ap4evb: add fsib 44100Hz rate
MAINTAINERS: update the ARM SH-Mobile git tree entry.
ARM: mach-shmobile: ap4evb: Mark NOR boot loader partitions read-only.
ARM: mach-shmobile: intc-sh7372: fix interrupt number
This avoids a deadlock in the IGMP code where one core gets a read
lock, another core starts trying to get a write lock (thus blocking
new readers), and then the first core tries to recursively re-acquire
the read lock.
We still try to preserve some degree of balance by giving priority
to additional write lockers that come along while the lock is held
for write, so they can all complete quickly and return the lock to
the readers.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Now that clk_set_rate_ex() is gone, there is also no way to get at rate
setting algo id, which is now also completely unused. Kill it off before
new clock ops start using it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 35bab0589b (ARM: imx: change the way
spi-imx devices are registered) contained a typo in mx25, leading to link time
failure.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Currently compilation breaks for the eukrea mbimx27 baseboard
when CONFIG_SPI_IMX is selected and CONFIG_TOUCHSCREEN_ADS7846
is not selected. Fix this by removing the ifdefs altogether.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Eric Benard <eric@eukrea.com>
* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: do not release any memory under 1M in domain 0
xen: events: do not unmask event channels on resume
xen: correct size of level2_kernel_pgt
* 'stable/xen-pcifront-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
MAINTAINERS: Mark XEN lists as moderated
xen-pcifront: fix PCI reference leak
xen-pcifront: Remove duplicate inclusion of headers.
xen: fix memory leak in Xen PCI MSI/MSI-X allocator.
MAINTAINERS: Update mailing list name for Xen pieces.
This hypercall allows Xen to specify a non-default location for the
machine to physical mapping. This capability is used when running a 32
bit domain 0 on a 64 bit hypervisor to shrink the hypervisor hole to
exactly the size required.
[ Impact: add Xen hypercall definitions ]
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: GIC: don't disable software generated interrupts
ARM: 6472/1: vexpress ct-ca9x4: only set twd_base if local timers are being used
ARM: arch/arm/kernel/traps.c: Convert sprintf_symbol to %pS
ARM: arch/arm/kernel/hw_breakpoint.c: Convert WARN_ON to WARN
ARM: 6462/1: EP93xx: Document DMA M2P API
ARM: 6470/1: atomic64: use generic implementation for OABI configurations
ARM: 6469/1: perf-events: squash compiler warning
ARM: 6468/1: backtrace: fix calculation of thread stack base
ARM: Fix DMA coherent allocator alignment
ARM: orion5x/kirkwood/mv78xx0: fix MPP configuration corner cases
[ARM] TS-78xxx NAND resource type should be IORESOURCE_MEM
ARM: pxa/saar: fix the building failure caused by typo
ARM: pxa/cm-x2xx: remove duplicate call to pxa27x_init_irq
ARM: pxa: fix the missing definition of IRQ_BOARD_END
ARM: mmp: fix cpuid detection on mmp2
[ARM] Kirkwood: restrict the scope of the PCIe reset workaround
[ARM] Kirkwood: fix timer initialization for LaCie boards
[ARM] Kirkwood: enhance TCLK detection
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, amd: Use kmalloc_node(,__GFP_ZERO) for northbridge structure allocation
perf_events: Fix time tracking in samples
perf trace: update usage
perf trace: update Documentation with new perf trace variants
perf trace: live-mode command-line cleanup
perf trace record: handle commands correctly
perf record: make the record options available outside perf record
perf trace scripting: remove system-wide param from shell scripts
perf trace scripting: fix some small memory leaks and missing error checks
perf: Fix usages of profile_cpu in builtin-top.c to use cpu_list
perf, ui: Eliminate stack-smashing protection compiler complaint
Both commits 0a3d763f1a ("ptrace: cleanup arch_ptrace() on um") and
9b05a69e05 ("ptrace: change signature of arch_ptrace()") broke the um
build. This patch fixes the issues.
0a3d763f1a introduced the undeclared variable "datavp". The patch seems
completely untested. :-(
9b05a69e05 changed arch_ptrace()'s signature but did not update
um/include/asm/ptrace-generic.h.
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Tested-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Software generated interrupts (SGI) are used for IPIs by the kernel.
While previous revisions of the GIC hardware were specified not to
implement enable bits for SGIs, more recent hardware is now permitted
to implement these bits in a per-CPU banked register.
The priority registers for the PPI and SGIs are also per-CPU banked
registers, so ensure that these are also appropriately initialized.
Reported-by: Scott Valentine <svalentine@concentris-systems.com>
Acked-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a single step exception fires, the trap bits, used to
signal hardware breakpoints, are in a random state.
These trap bits might be set if another exception will follow,
like a breakpoint in the next instruction, or a watchpoint in the
previous one. Or there can be any junk there.
So if we handle these trap bits during the single step exception,
we are going to handle an exception twice, or we are going to
handle junk.
Just ignore them in this case.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=21332
Reported-by: Michael Stefaniuc <mstefani@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Cc: Alexandre Julliard <julliard@winehq.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: All since 2.6.33.x <stable@kernel.org>
Set VM_PFNMAP in the privcmd mmap file_op, rather than later in
xen_remap_domain_mfn_range when it is too late because
vma_wants_writenotify has already been called and vm_page_prot has
already been modified.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Some BIOSes provide PCI host bridge windows that overlap, e.g.,
pci_root PNP0A03:00: host bridge window [mem 0xb0000000-0xffffffff]
pci_root PNP0A03:00: host bridge window [mem 0xafffffff-0xdfffffff]
pci_root PNP0A03:00: host bridge window [mem 0xf0000000-0xffffffff]
If we simply insert these as children of iomem_resource, the second window
fails because it conflicts with the first, and the third is inserted as a
child of the first, i.e.,
b0000000-ffffffff PCI Bus 0000:00
f0000000-ffffffff PCI Bus 0000:00
When we claim PCI device resources, this can cause collisions like this
if we put them in the first window:
pci 0000:00:01.0: address space collision: [mem 0xff300000-0xff4fffff] conflicts with PCI Bus 0000:00 [mem 0xf0000000-0xffffffff]
Host bridge windows are top-level resources by definition, so it doesn't
make sense to make the third window a child of the first. This patch
coalesces any host bridge windows that overlap. For the example above,
the result is this single window:
pci_root PNP0A03:00: host bridge window [mem 0xafffffff-0xffffffff]
This fixes a 2.6.34 regression.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=17011
Reported-and-tested-by: Anisse Astier <anisse@astier.eu>
Reported-and-tested-by: Pramod Dematagoda <pmd.lotr.gandalf@gmail.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is a big revert of a lot of -rc1 tidspbridge patches in order to
get the driver back into a working state. It also includes a OMAP patch
that was approved by the OMAP maintainer.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When running ktest.pl randconfig tests, I would sometimes trigger
a lockdep annotation bug (possible reason: unannotated irqs-on).
This triggering happened right after function tracer self test was
executed. After doing a config bisect I found that this was caused with
having function tracer, paravirt guest, prove locking, and rcu torture
all enabled.
The rcu torture just enhanced the likelyhood of triggering the bug.
Prove locking was needed, since it was the thing that was bugging.
Function tracer would trace and disable interrupts in all sorts
of funny places.
paravirt guest would turn arch_local_irq_* into functions that would
be traced.
Besides the fact that tracing arch_local_irq_* is just a bad idea,
this is what is happening.
The bug happened simply in the local_irq_restore() code:
if (raw_irqs_disabled_flags(flags)) { \
raw_local_irq_restore(flags); \
trace_hardirqs_off(); \
} else { \
trace_hardirqs_on(); \
raw_local_irq_restore(flags); \
} \
The raw_local_irq_restore() was defined as arch_local_irq_restore().
Now imagine, we are about to enable interrupts. We go into the else
case and call trace_hardirqs_on() which tells lockdep that we are enabling
interrupts, so it sets the current->hardirqs_enabled = 1.
Then we call raw_local_irq_restore() which calls arch_local_irq_restore()
which gets traced!
Now in the function tracer we disable interrupts with local_irq_save().
This is fine, but flags is stored that we have interrupts disabled.
When the function tracer calls local_irq_restore() it does it, but this
time with flags set as disabled, so we go into the if () path.
This keeps interrupts disabled and calls trace_hardirqs_off() which
sets current->hardirqs_enabled = 0.
When the tracer is finished and proceeds with the original code,
we enable interrupts but leave current->hardirqs_enabled as 0. Which
now breaks lockdeps internal processing.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
We already deliberately setup a 1-1 P2M for the region up to 1M in
order to allow code which assumes this region is already mapped to
work without having to convert everything to ioremap.
Domain 0 should not return any apparently unused memory regions
(reserved or otherwise) in this region to Xen since the e820 may not
accurately reflect what the BIOS has stashed in this region.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Also, don't be picky about the location, which incidentally fixes the
build since MEMBLOCK_REAL_LIMIT is gone on 2.6.37.
arch/arm/plat-omap/devices.c: In function 'omap_dsp_reserve_sdram_memblock':
arch/arm/plat-omap/devices.c:287: error: 'MEMBLOCK_REAL_LIMIT'
undeclared (first use in this function)
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Jasper suggested we use the zeroing capability of the allocators
instead of calling memset ourselves. Add node affinity while we're at
it.
Reported-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In commit bde28b84, I made the assumption that CONFIG_SMP is always set
for the quad-core ct-ca9x4 platform. As it turns out, people who aren't
using the SMP goodness are confronted with a build failure.
This patch fixes this issue by ensure that twd_base is only set if
local timers are being used (and therefore SMP support is configured).
Reported-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
check_enable_amd_mmconf_dmi() gets called only for the BSP,
hence everything hanging off of it can be __init*.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4CD2DE1E0200007800020990@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A new version of the SGI UV hub node controller is being
developed. A few of the MMRs (control registers) that exist on
the current hub no longer exist on the new hub. Fortunately,
there are alternate MMRs that are are functionally equivalent
and that exist on both hubs.
This patch changes the UV code to use MMRs that exist in BOTH
versions of the hub node controller.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20101106204056.GA27584@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Analog to git commit 737480a0d5
fix the return address of subsequent kretprobes when multiple
kretprobes are set on the same function.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Execute the kprobe exception and fault handler with interrupts disabled.
To disable the interrupts only while a single step is in progress is not
good enough, a kprobe from interrupt context while another kprobe is
handled can confuse the internal house keeping.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide the devmem_is_allowed() routine to restrict access to
kernel memory from userspace.
Set the CONFIG_STRICT_DEVMEM config option to switch on checking.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The check for the _PAGE_RO bit in get_user_pages_fast for write==1 is
the wrong way around. It must not be set for the fast path.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The [vk][cmz]alloc(_node) family of functions return void
pointers which it's completely unnecessary/pointless to cast to
other pointer types since that happens implicitly.
This patch removes such casts from arch/x86.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: trivial@kernel.org
Cc: amd64-microcode@amd64.org
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <alpine.LNX.2.00.1011082310220.23697@swampdragon.chaosbits.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
native_apic_msr_read() and x2apic_enabled() use rdmsr(msr, low, high),
but only use the low part.
gcc4.6 complains about this:
.../apic.h:144:11: warning: variable 'high' set but not used [-Wunused-but-set-variable]
rdmsr() is just a wrapper around rdmsrl() which splits the 64bit value
into low and high, so using rdmsrl() directly solves this.
[tglx: Changed the variables to u64 as suggested by Cyrill. It's less
confusing and has no code impact as this is 64bit only anyway.
Massaged changelog as well. ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: x86@kernel.org
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
LKML-Reference: <1289251229-19589-1-git-send-email-andi@firstfloor.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Get rid of the following warning:
arch/arm/mach-omap1/devices.c: In function 'omap_init_wdt':
arch/arm/mach-omap1/devices.c:298: warning: 'return' with
no value, in function returning non-void
while at that, also change:
platform_device_register();
return 0;
into:
return platform_device_register();
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Stanse found that xen_setup_msi_irqs leaks memory when
xen_allocate_pirq fails. Free the memory in that fail path.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: xen-devel@lists.xensource.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
This makes the loader and bootenv partitions read-only under MTD for the
on-board NOR flash.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These clocks are currently only used inside one .c file and are not
declared in any headers, therefore having them global is useless.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add kernel-doc documentation for the EP93xx DMA memory to
peripheral/peripheral to memory API.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The old apcs-gnu ABI doesn't guarantee that double words are allocated
to registers with even alignment, causing the 64-bit exclusive memory
operations to be rejected by the assembler.
This patch requires that CONFIG_AEABI is set in order to use the native
atomic operations and falls back to the generic (spinlock) code otherwise.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
armv7_pmnc_counter_has_overflowed can return uninitialised data
if an invalid counter is specified.
This patch fixes the code to return 0 in this case, which squashes
the compiler warning from GCC 4.5.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When unwinding stack frames we must take care not to unwind
areas of memory that lie outside of the known extent of the stack.
This patch fixes an incorrect calculation of the stack base where
THREAD_SIZE is added to the stack pointer after it has already
been aligned to this value. Since the ALIGN macro performs this
addition internally, we end up overshooting the base by 8k.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
An out by one bug meant that the DMA coherent allocator was aligning
to one more bit than it should, causing it to run out of available
memory quicker. Fix this.
Reported-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'kvm-updates/2.6.37' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: BookE: Load the lower half of MSR
KVM: PPC: BookE: fix sleep with interrupts disabled
KVM: PPC: e500: Call kvm_vcpu_uninit() before kvmppc_e500_tlb_uninit().
PPC: KVM: Book E doesn't have __end_interrupts.
KVM: x86: Issue smp_call_function_many with preemption disabled
KVM: x86: fix information leak to userland
KVM: PPC: fix information leak to userland
KVM: MMU: fix rmap_remove on non present sptes
KVM: Write protect memory after slot swap
#include <media/omap1_camera.h> directive is required to
compile the dependant boards (board-ams-delta for now).
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Flush the writes to IRQSTATUS_L0 register in the DMA interrupt handler by reading the register
directly after write. This prevents the spurious DMA interrupts noted when using VDD_OPP 1
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Acked-by: Santosh Shilimkar <Santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following error:
>regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
>twl_reg twl_reg.6: can't register VMMC1, -22
>twl_reg: probe of twl_reg.6 failed with error -22
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wrong MPP configuration would cause <cpu>_mpp_conf loop infinitely
because the mpp list iterator would not be incremented.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
The type was IORESOURCE_IO which is not what is expected by
plat_nand_probe(). This device has not worked since 2d098a72
("mtd: plat_nand: request memory resource before doing ioremap").
Signed-off-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: mark "hardwall" device as non-seekable
asm-generic/stat.h: support 64-bit file time_t for stat()
arch/tile: don't allow user code to set the PL via ptrace or signal return
arch/tile: correct double syscall restart for nested signals
arch/tile: avoid __must_check warning on one strict_strtol check
arch/tile: bomb raw_local_irq_ to arch_local_irq_
arch/tile: complete migration to new kmap_atomic scheme
This was preventing the guest from setting any bits in the
hardware MSR which aren't forced on, such as MSR[SPE].
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
It is not legal to call mutex_lock() with interrupts disabled.
This will assert with debug checks enabled.
If there's a real need to disable interrupts here, it could be done
after the mutex is acquired -- but I don't see why it's needed at all.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
