Remount currently happily accept any option thrown at it, although the
only filesystem specific option it actually handles is barrier/nobarrier.
And it actually doesn't handle these correctly either because it only uses
the value it parsed when we're doing a ro->rw transition. In addition to
that there's also a bad bug in xfs_parseargs which doesn't touch the
actual option in the mount point except for a single one,
XFS_MOUNT_SMALL_INUMS and thus forced any filesystem that's every
remounted in some way to not support 64bit inodes with no way to recover
unless unmounted.
This patch changes xfs_fs_remount to use it's own linux/parser.h based
options parse instead of xfs_parseargs and reject all options except for
barrier/nobarrier and to the right thing in general. Eventually I'd like
to have a single big option table used for mount aswell but that can wait
for a while.
SGI-PV: 983964
SGI-Modid: xfs-linux-melb:xfs-kern:31382a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
md raid1 can pass down barriers, but does not set an ordered flag on the
queue, so xfs does not even attempt a barrier write, and will never use
barriers on these block devices.
Remove the flag check and just let the barrier write test determine
barrier support.
A possible risk here is that if something does not set an ordered flag and
also does not properly return an error on a barrier write... but if it's
any consolation jbd/ext3/reiserfs never test the flag, and don't even do a
test write, they just disable barriers the first time an actual journal
barrier write fails.
SGI-PV: 983924
SGI-Modid: xfs-linux-melb:xfs-kern:31377a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Currently the xfs module init/exit code is a mess. It's farmed out over a
lot of function with very little error checking. This patch makes sure we
propagate all initialization failures properly and clean up after them.
Various runtime initializations are replaced with compile-time
initializations where possible to make this easier. The exit path is
similarly consolidated.
There's now split out function to create/destroy the kmem zones and
alloc/free the trace buffers. I've also changed the ktrace allocations to
KM_MAYFAIL and handled errors resulting from that.
And yes, we really should replace the XFS_*_TRACE ifdefs with a single
XFS_TRACE..
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:31354a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
can use the _ACL_TYPE_* definitions in linux-2.6/xfs_xattr.c. The
forthcoming generic acl code will also fix this problem.
SGI-PV: 982343
SGI-Modid: xfs-linux-melb:xfs-kern:31369a
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
If we don't do the blocksize/PAGESIZE check before calling
xfs_sb_validate_fsb_count() we can assert if we try to mount with a
blocksize > pagesize. The assert is valid so leave it and just move the
blocksize/pagesize check earlier.
SGI-PV: 983734
SGI-Modid: xfs-linux-melb:xfs-kern:31365a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
As reported by Michael-John Turner XFS updates the mtime on the source
inode of a rename call in case it's a directory and changes the parent.
This doesn't make any sense, is not mentioned in the standards and not
performed by any other Linux filesystems so remove it.
SGI-PV: 983684
SGI-Modid: xfs-linux-melb:xfs-kern:31364a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Barry Naujok <bnaujok@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
algorithm
If xfs_bmbt_split() cannot find an AG with sufficient free space to
satisfy a full extent btree split then fall back to the lowspace allocator
algorithm.
SGI-PV: 983338
SGI-Modid: xfs-linux-melb:xfs-kern:31359a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
When free space is running low the extent allocator may choose to allocate
an extent from an AG without leaving sufficient space for a btree split
when inserting the new extent (see where xfs_bmap_btalloc() sets minleft
to 0). In this case the allocator will enable the lowspace algorithm which
is supposed to allow further allocations (such as btree splits and
newroots) to allocate from sequential AGs. This algorithm has been broken
for a long time and this patch restores its behaviour.
SGI-PV: 983338
SGI-Modid: xfs-linux-melb:xfs-kern:31358a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
The bmap btree split code relies on a previous data extent allocation
(from xfs_bmap_btalloc()) to find an AG that has sufficient space to
perform a full btree split, when inserting the extent. When converting
unwritten extents we don't allocate a data extent so a btree split will be
the first allocation. In this case we need to set minleft so the allocator
will pick an AG that has space to complete the split(s).
SGI-PV: 983338
SGI-Modid: xfs-linux-melb:xfs-kern:31357a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
xfs_attrmulti_by_handle currently request the size based on
sizeof(attr_multiop_t) but should be using sizeof(xfs_attr_multiop_t)
because that is what it is dealing with. Despite beeing wrong this
actually harmless in practice because both structures are the same size on
all platforms.
But this sizeof was the only user of struct attr_multiop so we can just
kill it. Also move the ATTR_OP_* defines xfs_attr.h into the struct
xfs_attr_multiop defintion in xfs_fs.h because they are only used with
that structure, and are part of the user ABI for the
XFS_IOC_ATTRMULTI_BY_HANDLE ioctl.
SGI-PV: 983508
SGI-Modid: xfs-linux-melb:xfs-kern:31352a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_attrlist_by_handle should only take the ATTR_ flags for the root
namespaces. The ATTR_KERN* flags may change at anytime and expect special
preconditions that can't be guaranteed for userspace-originating requests.
For example passing down ATTR_KERNNOVAL through xfs_attrlist_by_handle
will hit an assert in debug builds currently.
SGI-PV: 983677
SGI-Modid: xfs-linux-melb:xfs-kern:31351a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
After a btree insert operation a cursor can be invalid due to block splits
and a maybe a new root block. We reset the cursor in xfs_bmbt_insert() in
the cases where we think we need to but it isn't enough as we still see
assertions. Just do what we do elsewhere and reset the cursor
unconditionally. Also remove the fix to revalidate the original cursor in
xfs_bmbt_insert().
SGI-PV: 983336
SGI-Modid: xfs-linux-melb:xfs-kern:31342a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
ASSERTs are no good to us on a non-debug build so use
XFS_WANT_CORRUPTED_GOTOs to report extent btree corruption ASAP.
SGI-PV: 983500
SGI-Modid: xfs-linux-melb:xfs-kern:31338a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
xfs_dir2_node_lookup() calls xfs_da_node_lookup_int() which iterates
through leaf blocks containing the matching hash value for the name being
looked up. Inside xfs_da_node_lookup_int(), it calls the
xfs_dir2_leafn_lookup_for_entry() for each leaf block.
xfs_dir2_leafn_lookup_for_entry() iterates through each matching
hash/offset pair doing a name comparison to find the matching dirent.
For CI mode, the state->extrablk retains the details of the block that has
the CI match so xfs_dir2_node_lookup() can return the case-preserved name.
The original implementation didn't retain the xfs_da_buf_t properly, so
the lookup was returning a bogus name to be stored in the dentry.
In the case of unlink, the bad name was passed and in debug mode, ASSERTed
when it can't find the entry.
SGI-PV: 983284
SGI-Modid: xfs-linux-melb:xfs-kern:31337a
Signed-off-by: Barry Naujok <bnaujok@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
The core kernel uses vfs_getattr to look at the inode size and similar
attributes, so there is no need to keep i_size uptodate for directories or
special files. This means we can remove xfs_validate_fields because the
I/O path already keeps i_size uptodate for regular files.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31336a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Barry Naujok <bnaujok@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_remove and xfs_rmdir are almost the same with a little more work
performed in xfs_rmdir due to the . and .. entries. This patch merges
xfs_rmdir into xfs_remove and performs these actions conditionally.
Also clean up the error handling which was a nightmare in both versions
before.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31335a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Barry Naujok <bnaujok@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
context count of ssize_t versus int. Change context count to be ssize_t.
SGI-PV: 983395
SGI-Modid: xfs-linux-melb:xfs-kern:31333a
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
This function is used to compact the indirect extent list by moving
extents from one page to the previous to fill them up. After we move some
extents to an earlier page we need to shuffle the remaining extents to the
start of the page. The actual bug here is the second argument to memmove()
needs to index past the extents, that were copied to the previous page,
and move the remaining extents. For pages that are already full (ie
ext_avail == 0) the compaction code has no net effect so don't do it.
SGI-PV: 983337
SGI-Modid: xfs-linux-melb:xfs-kern:31332a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
During a forced shutdown a xfs inode can be destroyed before log I/O
involving that inode is complete. We need to wait for the inode to be
unpinned before tearing it down. Version 2 cleans up the code a bit by
relying on xfs_iflush() to do the unpinning and forced shutdown check.
SGI-PV: 981240
SGI-Modid: xfs-linux-melb:xfs-kern:31326a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
and not go through xfs_attr_list.
SGI-PV: 983395
SGI-Modid: xfs-linux-melb:xfs-kern:31324a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
architecture.
This should fix the longstanding issues with xfs and old ABI arm boxes,
which lead to various asserts and xfs shutdowns, and for which an
(incorrect) patch has been floating around for years.
I've verified this patch by comparing the on-disk structure layouts using
pahole from the dwarves package, as well as running through a bit of xfsqa
under qemu-arm, modified so that the check/repair phase after each test
actually executes check/repair from the x86 host, on the filesystem
populated by the arm emulator. Thus far it all looks good.
There are 2 other structures with extra padding at the end, but they don't
seem to cause trouble. I suppose they could be packed as well:
xfs_dir2_data_unused_t and xfs_dir2_sf_t.
Note that userspace needs a similar treatment, and any filesystems which
were running with the previous rogue "fix" will now see corruption (either
in the kernel, or during xfs_repair) with this fix properly in place; it
may be worth teaching xfs_repair to identify and fix that specific issue.
SGI-PV: 982930
SGI-Modid: xfs-linux-melb:xfs-kern:31280a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Use the generic set, get and removexattr methods and supply the s_xattr
array with fine-grained handlers. All XFS/Linux highlevel attr handling is
rewritten from scratch and placed into fs/xfs/linux-2.6/xfs_xattr.c so
that it's separated from the generic low-level code.
SGI-PV: 982343
SGI-Modid: xfs-linux-melb:xfs-kern:31234a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
The vfs_unlink/d_delete functionality in the Linux VFS make the
dentry negative if it is the only inode being referenced. Case-insensitive
mode doesn't work with negative dentries, so if using CI-mode, invalidate
the dentry on unlink/rmdir.
SGI-PV: 983102
SGI-Modid: xfs-linux-melb:xfs-kern:31308a
Signed-off-by: Barry Naujok <bnaujok@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Fixes a problem in the xfs_dir2_remove and xfs_dir2_replace paths which
intenally call directory format specific lookup funtions that assume
args->cmpresult is zeroed.
SGI-PV: 982606
SGI-Modid: xfs-linux-melb:xfs-kern:31268a
Signed-off-by: Barry Naujok <bnaujok@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Implement ASCII case-insensitive support. It's primary purpose is for
supporting existing filesystems that already use this case-insensitive
mode migrated from IRIX. But, if you only need ASCII-only case-insensitive
support (ie. English only) and will never use another language, then this
mode is perfectly adequate.
ASCII-CI is implemented by generating hashes based on lower-case letters
and doing lower-case compares. It implements a new xfs_nameops vector for
doing the hashes and comparisons for all filename operations.
To create a filesystem with this CI mode, use: # mkfs.xfs -n version=ci
<device>
SGI-PV: 981516
SGI-Modid: xfs-linux-melb:xfs-kern:31209a
Signed-off-by: Barry Naujok <bnaujok@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
This implements the code to store the actual filename found during a
lookup in the dentry cache and to avoid multiple entries in the dcache
pointing to the same inode.
To avoid polluting the dcache, we implement a new directory inode
operations for lookup. xfs_vn_ci_lookup() stores the correct case name in
the dcache.
The "actual name" is only allocated and returned for a case- insensitive
match and not an actual match.
Another unusual interaction with the dcache is not storing negative
dentries like other filesystems doing a d_add(dentry, NULL) when an ENOENT
is returned. During the VFS lookup, if a dentry returned has no inode,
dput is called and ENOENT is returned. By not doing a d_add, this actually
removes it completely from the dcache to be reused. create/rename have to
be modified to support unhashed dentries being passed in.
SGI-PV: 981521
SGI-Modid: xfs-linux-melb:xfs-kern:31208a
Signed-off-by: Barry Naujok <bnaujok@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
The end of the xfs_da_args structure has 4 unsigned char fields for
true/false information on directory and attr operations using the
xfs_da_args structure.
The following converts these 4 into a op_flags field that uses the first 4
bits for these fields and allows expansion for future operation
information (eg. case-insensitive lookup request).
SGI-PV: 981520
SGI-Modid: xfs-linux-melb:xfs-kern:31206a
Signed-off-by: Barry Naujok <bnaujok@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Adds two pieces of functionality for the basis of case-insensitive support
in XFS:
1. A comparison result enumerated type: xfs_dacmp. It represents an
exact match, case-insensitive match or no match at all. This patch
only implements different and exact results.
2. xfs_nameops vector for specifying how to perform the hash generation
of filenames and comparision methods. In this patch the hash vector
points to the existing xfs_da_hashname function and the comparison
method does a length compare, and if the same, does a memcmp and
return the xfs_dacmp result.
All filename functions that use the hash (create, lookup remove, rename,
etc) now use the xfs_nameops.hashname function and all directory lookup
functions also use the xfs_nameops.compname function.
The lookup functions also handle case-insensitive results even though the
default comparison function cannot return that. And important aspect of
the lookup functions is that an exact match always has precedence over a
case-insensitive. So while a case-insensitive match is found, we have to
keep looking just in case there is an exact match. In the meantime, the
info for the first case-insensitive match is retained if no exact match is
found.
SGI-PV: 981519
SGI-Modid: xfs-linux-melb:xfs-kern:31205a
Signed-off-by: Barry Naujok <bnaujok@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
de-duplicate calls to xfs_attr_trace_enter
Every call to xfs_attr_trace_enter() shares the exact same 16 args in the
middle... just send in the context pointer and let the next level down
split it into the ktrace.
Compile tested only.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:31200a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_binval aka xfs_flush_buftarg is the first thing done in
xfs_free_buftarg, so there is no need to have duplicated calls just before
xfs_free_buftarg in the mount failure path.
SGI-PV: 981951
SGI-Modid: xfs-linux-melb:xfs-kern:31197a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_mount_init is inlined into xfs_fs_fill_super and allocation switched
to kzalloc. Plug a leak of the mount structure for most early mount
failures. Move xfs_icsb_init_counters to as late as possible in the mount
path and make sure to undo it so that no stale hotplug cpu notifiers are
left around on mount failures.
SGI-PV: 981951
SGI-Modid: xfs-linux-melb:xfs-kern:31196a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Split setting the block and sector size out of xfs_fs_fill_super into a
small helper to make xfs_fs_fill_super more readable.
SGI-PV: 981951
SGI-Modid: xfs-linux-melb:xfs-kern:31194a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Currently closing the rt/log block device is done in the wrong spot, and
far too early. So revampt it:
- xfs_blkdev_put moved out of xfs_free_buftarg into the caller so that
it is done after tearing down the buftarg completely.
- call to xfs_unmountfs_close moved from xfs_mountfs into caller so
that it's done after tearing down the filesystem completely.
- xfs_unmountfs_close is renamed to xfs_close_devices and made static
in xfs_super.c
- opening of the block devices is split into a helper xfs_open_devices
that is symetric in use to xfs_close_devices
- xfs_unmountfs can now lose struct cred
- error handling around device opening sanitized in xfs_fs_fill_super
SGI-PV: 981951
SGI-Modid: xfs-linux-melb:xfs-kern:31193a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Freeing of the superblock is already handled in the caller, and that is
more symmetric with the mount path, too.
SGI-PV: 981951
SGI-Modid: xfs-linux-melb:xfs-kern:31192a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_mount is already pretty linux-specific so merge it into
xfs_fs_fill_super to allow for a more structured mount code in the next
patches. xfs_start_flags and xfs_finish_flags also move to xfs_super.c.
SGI-PV: 981951
SGI-Modid: xfs-linux-melb:xfs-kern:31189a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_unmount is small and already pretty Linux specific, so merge it into
the callers. The real unmount path is simplified a little by doing a
WARN_ON on the xfs_unmount_flush retval directly instead of propagating
the error back to the caller, and the mout failure case in simplified
significantly by removing the forced shutdown case and all the dmapi
events that shouldn't be sent because the dmapi mount event hasn't been
sent by that time either.
SGI-PV: 981951
SGI-Modid: xfs-linux-melb:xfs-kern:31188a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_igrow_start just expands to xfs_zero_eof with two asserts that are
useless in the context of the only caller and some rather confusing
comments.
xfs_igrow_finish is just a few lines of code decorated again with useless
asserts and confusing comments.
Just kill those two and merge them into xfs_setattr.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31186a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
xfs_mntupdate already is completely Linux specific due to the VFS flags
passed in, so it might aswell be merged into xfs_fs_remount.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31185a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Quite useless wrapper that doesn't help making the code more readable.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31184a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Recent changes to update the version number during mount (attr2 stuff)
failed to change the assert that checked for calid flags being changed on
mount. Clearly this path hasn't been exercised by the test code....
SGI-PV: 981950
SGI-Modid: xfs-linux-melb:xfs-kern:31183a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
No need for addition permission checks in the xattr handler,
fs/xattr.c:xattr_permission() already does them, and in fact slightly more
strict then what was in the attr_capable handlers.
SGI-PV: 981809
SGI-Modid: xfs-linux-melb:xfs-kern:31164a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
The l_flushsema doesn't exactly have completion semantics, nor mutex
semantics. It's used as a list of tasks which are waiting to be notified
that a flush has completed. It was also being used in a way that was
potentially racy, depending on the semaphore implementation.
By using a sv_t instead of a semaphore we avoid the need for a separate
counter, since we know we just need to wake everything on the queue.
Original waitqueue implementation from Matthew Wilcox. Cleanup and
conversion to sv_t by Christoph Hellwig.
SGI-PV: 981507
SGI-Modid: xfs-linux-melb:xfs-kern:31059a
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
