If an irq is pending when devm_request_irq() is called, the irq
handler will cause a NULL pointer access because initialisation
is not done yet.
Fixes: 9d7ee0e28d ("tty: serial: lpuart: avoid report NULL interrupt")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Indan Zupancic <Indan.Zupancic@mep-info.com>
Link: https://lore.kernel.org/r/20220505114750.45423-1-Indan.Zupancic@mep-info.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsmtty_write() does not prevent the user to use the full fifo size of 4096
bytes as allocated in gsm_dlci_alloc(). However, gsmtty_write_room() tries
to limit the return value by 'TX_SIZE' and returns a negative value if the
fifo has more than 'TX_SIZE' bytes stored. This is obviously wrong as
'TX_SIZE' is defined as 512.
Define 'TX_SIZE' to the fifo size and use it accordingly for allocation to
keep the current behavior. Return the correct remaining size of the fifo in
gsmtty_write_room() via kfifo_avail().
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220504081733.3494-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation activates the mux if it was restarted and opens
the control channel if the mux was previously closed and we are now acting
as initiator instead of responder, which is the default setting.
This has two issues.
1) No mux is activated if we keep all default values and only switch to
initiator. The control channel is not allocated but will be opened next
which results in a NULL pointer dereference.
2) Switching the configuration after it was once configured while keeping
the initiator value the same will not reopen the control channel if it was
closed due to parameter incompatibilities. The mux remains dead.
Fix 1) by always activating the mux if it is dead after configuration.
Fix 2) by always opening the control channel after mux activation.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220504081733.3494-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'len' is decreased after each octet that has its EA bit set to 0, which
means that the value is encoded with additional octets. However, the final
octet does not decreases 'len' which results in 'len' being one byte too
long. A buffer over-read may occur in tty_insert_flip_string() as it tries
to read one byte more than the passed content size of 'data'.
Decrease 'len' also for the final octet which has the EA bit set to 1 to
write the correct number of bytes from the internal receive buffer to the
virtual tty.
Fixes: 2e124b4a39 ("TTY: switch tty_flip_buffer_push")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220504081733.3494-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XON1/XOFF1 character registers are at offset 0xa0 and 0xa8
respectively, so we cannot use the definition in serial_port.h.
Fixes: bdbd0a7f8f ("serial: 8250-mtk: modify baudrate setting")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220427132328.228297-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the FEATURE_SEL at probe time to make sure that BIT(0) is enabled:
this guarantees that when the port is configured as AP UART, the
right register layout is interpreted by the UART IP.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220427132328.228297-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On MediaTek SoCs, the UART IP is 16550A compatible, but there are some
specific quirks: we are declaring a register shift of 2, but this is
only valid for the majority of the registers, as there are some that
are out of the standard layout.
Specifically, this driver is using definitions from serial_reg.h, where
we have a UART_EFR register defined as 2: this results in a 0x8 offset,
but there we have the FCR register instead.
The right offset for the EFR register on MediaTek UART is at 0x98,
so, following the decimal definition convention in serial_reg.h and
accounting for the register left shift of two, add and use the correct
register address for this IP, defined as decimal 38, so that the final
calculation results in (0x26 << 2) = 0x98.
Fixes: bdbd0a7f8f ("serial: 8250-mtk: modify baudrate setting")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220427132328.228297-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: 5930cb3511 ("serial: driver for Conexant Digicolor USART")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Baruch Siach <baruch@tkos.co.il>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220505124621.1592697-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'size' may be used uninitialized in gsm_dlci_modem_output() if called with
an adaption that is neither 1 nor 2. The function is currently only called
by gsm_modem_upd_via_data() and only for adaption 2.
Properly handle every invalid case by returning -EINVAL to silence the
compiler warning and avoid future regressions.
Fixes: c19ffe00fe ("tty: n_gsm: fix invalid use of MSC in advanced option")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220425104726.7986-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and is therefore driven by a fixed 62.5MHz clock
input derived from the 100MHz PCI Express clock. The clock rate is
divided by the oversampling rate of 16 as it is supplied to the baud
rate generator, yielding the baud base of 3906250.
Replace the incorrect baud base of 4000000 with the right value of
3906250 then, complementing commit 6cbe45d8ac ("serial: 8250: Correct
the clock for OxSemi PCIe devices").
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable <stable@kernel.org>
Fixes: 1bc8cde46a ("8250_pci: Added driver for Endrun Technologies PTP PCIe card.")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181515270.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sticky MCR bits are lost in console restoration if console suspending
has been disabled. This currently affects the AFE bit, which works in
combination with RTS which we set, so we want to make sure the UART
retains control of its FIFO where previously requested. Also specific
drivers may need other bits in the future.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 4516d50aab ("serial: 8250: Use canary to restart console after suspend")
Cc: stable@vger.kernel.org # v4.0+
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181518490.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.8.1 states that XON/XOFF characters
shall be used instead of Fcon/Fcoff command in advanced option mode to
handle flow control. Chapter 5.4.8.2 describes how XON/XOFF characters
shall be handled. Basic option mode only used Fcon/Fcoff commands and no
XON/XOFF characters. These are treated as data bytes here.
The current implementation uses the gsm_mux field 'constipated' to handle
flow control from the remote peer and the gsm_dlci field 'constipated' to
handle flow control from each DLCI. The later is unrelated to this patch.
The gsm_mux field is correctly set for Fcon/Fcoff commands in
gsm_control_message(). However, the same is not true for XON/XOFF
characters in gsm1_receive().
Disable software flow control handling in the tty to allow explicit
handling by n_gsm.
Add the missing handling in advanced option mode for gsm_mux in
gsm1_receive() to comply with the standard.
This patch depends on the following commit:
Commit 8838b2af23 ("tty: n_gsm: fix SW flow control encoding/handling")
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 states that the Modem Status
Command (MSC) shall only be used if the basic option was chosen.
The current implementation uses MSC frames even if advanced option was
chosen to inform the peer about modem line state updates. A standard
conform peer may choose to discard these frames in advanced option mode.
Furthermore, gsmtty_modem_update() is not part of the 'tty_operations'
functions despite its name.
Rename gsmtty_modem_update() to gsm_modem_update() to clarify this. Split
its function into gsm_modem_upd_via_data() and gsm_modem_upd_via_msc()
depending on the encoding and adaption. Introduce gsm_dlci_modem_output()
as adaption of gsm_dlci_data_output() to encode and queue empty frames in
advanced option mode. Use it in gsm_modem_upd_via_data().
gsm_modem_upd_via_msc() is based on the initial gsmtty_modem_update()
function which used only MSC frames to update modem states.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dynamic virtual tty registration was introduced to allow the user to handle
these cases with uevent rules. The following commits relate to this:
Commit 5b87686e32 ("tty: n_gsm: Modify gsmtty driver register method when config requester")
Commit 0b91b53323 ("tty: n_gsm: Save dlci address open status when config requester")
Commit 46292622ad ("tty: n_gsm: clean up indenting in gsm_queue()")
However, the following behavior can be seen with this implementation:
- n_gsm ldisc is activated via ioctl
- all configuration parameters are set to their default value (initiator=0)
- the mux gets activated and attached and gsmtty0 is being registered in
in gsm_dlci_open() after DLCI 0 was established (DLCI 0 is the control
channel)
- the user configures n_gsm via ioctl GSMIOC_SETCONF as initiator
- this re-attaches the n_gsm mux
- no new gsmtty devices are registered in gsmld_attach_gsm() because the
mux is already active
- the initiator side registered only the control channel as gsmtty0
(which should never happen) and no user channel tty
The commits above make it impossible to operate the initiator side as no
user channel tty is or will be available.
On the other hand, this behavior will make it also impossible to allow DLCI
parameter negotiation on responder side in the future. The responder side
first needs to provide a device for the application before the application
can set its parameters of the associated DLCI via ioctl.
Note that the user application is still able to detect a link establishment
without relaying to uevent by waiting for DTR open on responder side. This
is the same behavior as on a physical serial interface. And on initiator
side a tty hangup can be detected if a link establishment request failed.
Revert the commits above completely to always register all user channels
and no control channel after mux attachment. No other changes are made.
Fixes: 5b87686e32 ("tty: n_gsm: Modify gsmtty driver register method when config requester")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 927728a34f.
Once the uart_port->rs485->flag is set to SER_RS485_ENABLED, the port
should always work in RS485 mode. If users want the port to leave
RS485 mode, they need to call ioctl() to clear SER_RS485_ENABLED.
So here we shouldn't clear the RS485 bits in the shutdown().
Fixes: 927728a34f ("serial: sc16is7xx: Clear RS485 bits in the shutdown")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20220418094339.678144-1-hui.wang@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the peer is not informed about the initial state of the modem
control lines after a new DLCI has been opened.
Fix this by sending the initial modem control line states after DLCI open.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220420101346.3315-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 932d596378 ("serial: 8250: Return early in .start_tx() if there
are no chars to send") caused a regression where the drivers implementing
runtime PM stopped idling. This is because serial8250_rpm_put_tx() is now
unbalanced on early return, it normally gets called at __stop_tx().
Fixes: 932d596378 ("serial: 8250: Return early in .start_tx() if there are no chars to send")
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220411111657.16744-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 76821e222c ("serial: imx: ensure that RX irqs are off if RX is
off") accidentally enabled overrun interrupts unconditionally when
deferring DMA enable until after the receiver has been enabled during
startup.
Fix this by using the DMA-initialised instead of DMA-enabled flag to
determine whether overrun interrupts should be enabled.
Note that overrun interrupts are already accounted for in
imx_uart_clear_rx_errors() when using DMA since commit 41d98b5da9
("serial: imx-serial - update RX error counters when DMA is used").
Fixes: 76821e222c ("serial: imx: ensure that RX irqs are off if RX is off")
Cc: stable@vger.kernel.org # 4.17
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20220411081957.7846-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current timeout for draining the tx fifo in RS485 mode is calculated by
multiplying the time it takes to transmit one character (with the given
baud rate) with the maximal number of characters in the tx queue.
This timeout is too short for two reasons:
First when calculating the time to transmit one character integer division
is used which may round down the result in case of a remainder of the
division.
Fix this by rounding up the division result.
Second the hardware may need additional time (e.g for first putting the
characters from the fifo into the shift register) before the characters are
actually put onto the wire.
To be on the safe side double the current maximum number of iterations
that are used to wait for the queue draining.
Fixes: 8d47923772 ("serial: amba-pl011: add RS485 support")
Cc: stable@vger.kernel.org
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220408233503.7251-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.4.2 states that any received unnumbered
acknowledgment (UA) with its poll/final (PF) bit set to 0 shall be
discarded. Currently, all UA frame are handled in the same way regardless
of the PF bit. This does not comply with the standard.
Remove the UA case in gsm_queue() to process only UA frames with PF bit set
to 1 to abide the standard.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-20-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsmtty_write() and gsm_dlci_data_output() properly guard the fifo access.
However, gsm_dlci_close() and gsmtty_flush_buffer() modifies the fifo but
do not guard this.
Add a guard here to prevent race conditions on parallel writes to the fifo.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-17-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm_control_modem() informs the virtual tty that more data can be written
after receiving a control signal octet via modem status command (MSC).
However, gsm_dlci_data() fails to do the same after receiving a control
signal octet from the convergence layer type 2 header.
Add tty_wakeup() in gsm_dlci_data() for convergence layer type 2 to fix
this.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-14-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. The value of the modem status command (MSC) frame
contains an address field, control signal and optional break signal octet.
The address field is encoded as described in chapter 5.2.1.2 with only one
octet (may be extended to more in future versions of the standard). Whereas
the control signal and break signal octet are always one byte each. This is
strange at first glance as it makes the EA bit redundant. However, the same
two octets are also encoded as header in convergence layer type 2 as
described in chapter 5.5.2. No header length field is given and the only
way to test if there is an optional break signal octet is via the EA flag
which extends the control signal octet with a break signal octet. Now it
becomes obvious how the EA bit for those two octets shall be encoded in the
MSC frame. The current implementation treats the signal octet different for
MSC frame and convergence layer type 2 header even though the standard
describes it for both in the same way.
Use the EA bit to encode the signal octets not only in the convergence
layer type 2 header but also in the MSC frame in the same way with either
1 or 2 bytes in case of an optional break signal. Adjust the receiving path
accordingly in gsm_control_modem().
Fixes: 3ac06b9056 ("tty: n_gsm: Fix for modems with brk in modem status control")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-13-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.1 states that each command frame shall
be made up from type, length and value. Looking for example in chapter
5.4.6.3.5 at the description for the encoding of a flow control on command
it becomes obvious, that the type and length field is always present
whereas the value may be zero bytes long. The current implementation omits
the length field if the value is not present. This is wrong.
Correct this by always sending the length in gsm_control_transmit().
So far only the modem status command (MSC) has included a value and encoded
its length directly. Therefore, also change gsmtty_modem_update().
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-12-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_config() fails to limit this range correctly. Furthermore,
gsm_control_retransmit() handles this number incorrectly by performing
N2 - 1 retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix the range check in gsm_config() and the value handling in
gsm_control_send() and gsm_control_retransmit() to comply with 3GPP 27.010.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-11-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In gsm_cleanup_mux() the muxer is closed down and all queues are removed.
However, removing the queues is done without explicit control of the
underlying buffers. Flush those before freeing up our queues to ensure
that all outgoing queues are cleared consistently. Otherwise, a new mux
connection establishment attempt may time out while the underlying tty is
still busy sending out the remaining data from the previous connection.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-10-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current DLCI release order starts with the control channel followed by
the user channels. Reverse this order to keep the control channel open
until all user channels have been released.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-9-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.2 states that the maximum frame size
(N1) refers to the length of the information field (i.e. user payload).
However, 'txframe' stores the whole frame including frame header, checksum
and start/end flags. We also need to consider the byte stuffing overhead.
Define constant for the protocol overhead and adjust the 'txframe' size
calculation accordingly to reserve enough space for a complete mux frame
including byte stuffing for advanced option mode. Note that no byte
stuffing is applied to the start and end flag.
Also use MAX_MTU instead of MAX_MRU as this buffer is used for data
transmission.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-8-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gsm_mux field 'malformed' represents the number of malformed frames
received. However, gsm1_receive() also increases this counter for any out
of frame byte.
Fix this by ignoring out of frame data for the malformed counter.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The frame checksum (FCS) is currently handled in gsm_queue() after
reception of a frame. However, this breaks layering. A workaround with
'received_fcs' was implemented so far.
Furthermore, frames are handled as such even if no end flag was received.
Move FCS calculation from gsm_queue() to gsm0_receive() and gsm1_receive().
Also delay gsm_queue() call there until a full frame was received to fix
both points.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-6-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.5.2 describes that the signal octet in
convergence layer type 2 can be either one or two bytes. The length is
encoded in the EA bit. This is set 1 for the last byte in the sequence.
gsmtty_modem_update() handles this correctly but gsm_dlci_data_output()
fails to set EA to 1. There is no case in which we encode two signal octets
as there is no case in which we send out a break signal.
Therefore, always set the EA bit to 1 for the signal octet to fix this.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Internally, we manage the alive state of the mux channels and mux itself
with the field member 'dead'. This makes it possible to notify the user
if the accessed underlying link is already gone. On the other hand,
however, removing the virtual ttys before terminating the channels may
result in peer messages being received without any internal target. Move
the mux cleanup procedure from gsmld_detach_gsm() to gsmld_close() to fix
this by keeping the virtual ttys open until the mux has been cleaned up.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The active mux instances are managed in the gsm_mux array and via mux_get()
and mux_put() functions separately. This gives a very loose coupling
between the actual instance and the gsm_mux array which manages it. It also
results in unnecessary lockings which makes it prone to failures. And it
creates a race condition if more than the maximum number of mux instances
are requested while the user changes the parameters of an active instance.
The user may loose ownership of the current mux instance in this case.
Fix this by moving the gsm_mux array handling to the mux allocation and
deallocation functions.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.8.2 states that both sides will revert to
the non-multiplexed mode via a close-down message (CLD). The usual program
flow is as following:
- start multiplex mode by sending AT+CMUX to the mobile
- establish the control channel (DLCI 0)
- establish user channels (DLCI >0)
- terminate user channels
- send close-down message (CLD)
- revert to AT protocol (i.e. leave multiplexed mode)
The AT protocol is out of scope of the n_gsm driver. However,
gsm_disconnect() sends CLD if gsm_config() detects that the requested
parameters require the mux protocol to restart. The next immediate action
is to start the mux protocol by opening DLCI 0 again. Any responder side
which handles CLD commands correctly forces us to fail at this point
because AT+CMUX needs to be sent to the mobile to start the mux again.
Therefore, remove the CLD command in this phase and keep both sides in
multiplexed mode.
Remove the gsm_disconnect() function as it become unnecessary and merge the
remaining parts into gsm_cleanup_mux() to handle the termination order and
locking correctly.
Fixes: 71e0779153 ("tty: n_gsm: do not send/receive in ldisc close path")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, only the initiator resets the mux protocol if the user requests
new parameters that are incompatible to those of the current connection.
The responder also needs to reset the multiplexer if the new parameter set
requires this. Otherwise, we end up with an inconsistent parameter set
between initiator and responder.
Revert the old behavior to inform the peer upon an incompatible parameter
set change from the user on the responder side by re-establishing the mux
protocol in such case.
Fixes: 509067bbd2 ("tty: n_gsm: Delete gsm_disconnect when config requester")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The below commit changed types of some hooks in struct psc_ops. It also
changed the types of the functions which are referenced in the instances
of the above struct.
However the commit did so only for CONFIG_PPC_MPC52xx, but not for
CONFIG_PPC_MPC512x. This results in build errors like:
mpc52xx_uart.c:static unsigned int mpc52xx_psc_raw_tx_rdy(struct uart_port *port)
mpc52xx_uart.c:static int mpc512x_psc_raw_tx_rdy(struct uart_port *port)
^^^
mpc52xx_uart.c:static int mpc5125_psc_raw_tx_rdy(struct uart_port *port)
^^^
Therefore, fix the latter case now too.
Fixes: 18662a1d8f (tty: serial: mpc52xx_uart: make rx/tx hooks return unsigned)
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220404055122.31194-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the big set of tty and serial driver changes for 5.18-rc1.
Nothing major, some more good cleanups from Jiri and 2 new serial
drivers. Highlights include:
- termbits cleanups
- export symbol cleanups and other core cleanups from Jiri Slaby
- new sunplus and mvebu uart drivers (amazing that people are
still creating new uarts...)
- samsung serial driver cleanups
- ldisc 29 is now "reserved" for experimental/development line
disciplines
- lots of other tiny fixes and cleanups to serial drivers and
bindings
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkGznQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnFwCgwGD/syV+BH2krgY6cRixZz72vPsAn2RSnicd
2YUwSNCHoL+B7hvQMtDG
=A3X9
-----END PGP SIGNATURE-----
Merge tag 'tty-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver changes for 5.18-rc1.
Nothing major, some more good cleanups from Jiri and 2 new serial
drivers. Highlights include:
- termbits cleanups
- export symbol cleanups and other core cleanups from Jiri Slaby
- new sunplus and mvebu uart drivers (amazing that people are still
creating new uarts...)
- samsung serial driver cleanups
- ldisc 29 is now "reserved" for experimental/development line
disciplines
- lots of other tiny fixes and cleanups to serial drivers and
bindings
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (104 commits)
vt_ioctl: fix potential spectre v1 in VT_DISALLOCATE
serial: 8250: fix XOFF/XON sending when DMA is used
tty: serial: samsung: Add ARTPEC-8 support
dt-bindings: serial: samsung: Add ARTPEC-8 UART
serial: sc16is7xx: Clear RS485 bits in the shutdown
tty: serial: samsung: simplify getting OF match data
tty: serial: samsung: constify variables and pointers
tty: serial: samsung: constify s3c24xx_serial_drv_data members
tty: serial: samsung: constify UART name
tty: serial: samsung: constify s3c24xx_serial_drv_data
tty: serial: samsung: reduce number of casts
tty: serial: samsung: embed s3c2410_uartcfg in parent structure
tty: serial: samsung: embed s3c24xx_uart_info in parent structure
serial: 8250_tegra: mark acpi_device_id as unused with !ACPI
tty: serial: bcm63xx: use more precise Kconfig symbol
serial: SERIAL_SUNPLUS should depend on ARCH_SUNPLUS
tty: serial: jsm: fix two assignments in if conditions
tty: serial: jsm: remove redundant assignments to variable linestatus
serial: 8250_mtk: make two read-only arrays static const
serial: samsung_tty: do not unlock port->lock for uart_write_wakeup()
...
At each login the user forces the kernel to create a new terminal and
allocate up to ~1Kb memory for the tty-related structures.
By default it's allowed to create up to 4096 ptys with 1024 reserve for
initial mount namespace only and the settings are controlled by host
admin.
Though this default is not enough for hosters with thousands of
containers per node. Host admin can be forced to increase it up to
NR_UNIX98_PTY_MAX = 1<<20.
By default container is restricted by pty mount_opt.max = 1024, but
admin inside container can change it via remount. As a result, one
container can consume almost all allowed ptys and allocate up to 1Gb of
unaccounted memory.
It is not enough per-se to trigger OOM on host, however anyway, it
allows to significantly exceed the assigned memcg limit and leads to
troubles on the over-committed node.
It makes sense to account for them to restrict the host's memory
consumption from inside the memcg-limited container.
Link: https://lkml.kernel.org/r/5d4bca06-7d4f-a905-e518-12981ebca1b3@virtuozzo.com
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus types,
causing updates to most SPI device drivers. The branch with that on has
been cross merged with a couple of other trees which added new SPI
drivers this cycle, I'm not expecting any build issues resulting from
the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmI4b+8ACgkQJNaLcl1U
h9AB+Qf/WhPzDSCdhK1repnSmEpRNs/J6hItmY2H6pTQaWALpfTB0+p1Nb5tAotg
fHbu6a2AsiiwWt+tDal44GFYhS0CDSOT4hqgLV8msyDDPPJqqr7A2dbu7YrCjTVI
TgNZNwxW7c2LgqBXR9GV7NPWYoxYxveoYh+L+05MSuSQxSOvPl6LUZiZPnPufQM6
dCpEh19atrtasFg3rFnslWBd2C3h8hb6YT7vUZs9gxhg3FvSgpYQwzz5SfFgHXK6
Rg07m8fDTSjf2qo1C4pc/d1Ni1xBe7aHKMtjtR3jJ4q8QqiawfCcvvOep/Iaec1+
s3qnDthohWMJoF1W6ERf3HiAgNIfhg==
=4tlR
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus
types, causing updates to most SPI device drivers. The branch with
that on has been cross merged with a couple of other trees which added
new SPI drivers this cycle, I'm not expecting any build issues
resulting from the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than
numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021"
[ And this is obviously where that spi change that snuck into the
regulator tree _should_ have been :^]
* tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (124 commits)
spi: fsi: Implement a timeout for polling status
spi: Fix erroneous sgs value with min_t()
spi: tegra20: Use of_device_get_match_data()
spi: mediatek: add ipm design support for MT7986
spi: Add compatible for MT7986
spi: sun4i: fix typos in comments
spi: mediatek: support tick_delay without enhance_timing
spi: Update clock-names property for arm pl022
spi: rockchip-sfc: fix platform_get_irq.cocci warning
spi: s3c64xx: Add spi port configuration for Tesla FSD SoC
spi: dt-bindings: samsung: Add fsd spi compatible
spi: topcliff-pch: Prevent usage of potentially stale DMA device
spi: tegra210-quad: combined sequence mode
spi: tegra210-quad: add acpi support
spi: npcm-fiu: Fix typo ("npxm")
spi: Fix Tegra QSPI example
spi: qup: replace spin_lock_irqsave by spin_lock in hard IRQ
spi: cadence: fix platform_get_irq.cocci warning
spi: Update NXP Flexspi maintainer details
dt-bindings: mfd: maxim,max77802: Convert to dtschema
...
In VT_ACTIVATE an almost identical code path has been patched
with array_index_nospec. In the VT_DISALLOCATE path, the arg is
the user input from a system call argument and lately used as a index
for vc_cons[index].d access, which can be reached through path like
vt_disallocate->vc_busy or vt_disallocate->vc_deallocate.
For consistency both code paths should have the same mitigations
applied. Also, the code style is adjusted as suggested by Jiri.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220314122921.31223-1-xiam0nd.tong@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When 8250 UART is using DMA, x_char (XON/XOFF) is never sent
to the wire. After this change, x_char is injected correctly.
Create uart_xchar_out() helper for sending the x_char out and
accounting related to it. It seems that almost every driver
does these same steps with x_char. Except for 8250, however,
almost all currently lack .serial_out so they cannot immediately
take advantage of this new helper.
The downside of this patch is that it might reintroduce
the problems some devices faced with mixed DMA/non-DMA transfer
which caused revert f967fc8f16 (Revert "serial: 8250_dma:
don't bother DMA with small transfers"). However, the impact
should be limited to cases with XON/XOFF (that didn't work
with DMA capable devices to begin with so this problem is not
very likely to cause a major issue, if any at all).
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Reported-by: Gilles Buloz <gilles.buloz@kontron.com>
Tested-by: Gilles Buloz <gilles.buloz@kontron.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220314091432.4288-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the UART block on the ARTPEC-8 SoC. This is closely
related to the variants used on the Exynos chips. The register layout
is identical to Exynos850 et al but the fifo size is different (64 bytes
in each direction for all instances).
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220311094515.3223023-3-vincent.whitchurch@axis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We tested RS485 function on an EVB which has SC16IS752, after
finishing the test, we started the RS232 function test, but found the
RTS is still working in the RS485 mode.
That is because both startup and shutdown call port_update() to set
the EFCR_REG, this will not clear the RS485 bits once the bits are set
in the reconf_rs485(). To fix it, clear the RS485 bits in shutdown.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20220308110042.108451-1-hui.wang@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the code with of_device_get_match_data() and use dev_of_node()
to remove ifdef-erry.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308080919.152715-9-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Constify variables, data pointed by several pointers and
"udivslot_table" static array. This makes code a bit safer.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308080919.152715-8-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver data (struct s3c24xx_serial_drv_data) is never modified, so
also its members can be made const. Except code style this has no
impact because the structure itself is always a const.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308080919.152715-7-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART name from driver data holds only string literals.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308080919.152715-6-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver data (struct s3c24xx_serial_drv_data) is only used to
initialize the driver properly and is not modified. Make it const.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308080919.152715-5-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointers to instances of "struct s3c24xx_serial_drv_data" are first
cast to kernel_ulong_t and then either used directly
(in "platform_device_id.driver_data") or cast again to void * (in
"of_device_id.data").
One cast can be dropped, so at least for "of_device_id.data" case there
will be no casts at all. This makes the code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308080919.152715-4-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
