Before dma_transfer_direction was introduced to replace
dma_data_direction, some dmaengine device uses DMA_NONE of
dma_data_direction for some talk with its client drivers.
The mxs-dma and its clients mxs-mmc and gpmi-nand are such case.
This patch adds DMA_TRANS_NONE to dma_transfer_direction and
migrate the DMA_NONE use in mxs-dma to it.
It also fixes the compile warning below.
CC drivers/dma/mxs-dma.o
drivers/dma/mxs-dma.c: In function ‘mxs_dma_prep_slave_sg’:
drivers/dma/mxs-dma.c:420:16: warning: comparison between ‘enum dma_transfer_direction’ and ‘enum dma_data_direction’
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This is how the original Freescale code (unintentionally) worked,
because the code path which would have asserted the CLKGATE bit was
never actually reached in their code.
This fixes the nefarious "DMA timout" bug when multiple DMA channels
(e.g. GPMI NAND and MMC) are used at the same time.
If a better fix for this problem should be found, the clkgate handling
could be reinstated.
See http://lists.infradead.org/pipermail/linux-arm-kernel/2011-September/065228.html
Also reverse the order of mxs_dma_disable_chan() and
mxs_dma_reset_chan() in mxs_dma_control() because mxs_dma_reset_chan()
can only work when the DMA channel is enabled.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Using a static variable for counting the number of CCWs attached to
a DMA channel when appending a new descriptor is not multi user safe.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
There is no need to have the clock enabled all the time the driver is
loaded.
It will be enabled anyway in mxs_dma_alloc_chan_resources() when a
channel is actually going to be used.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
After calling mxs_dma_disable_chan() for a channel, that channel
becomes unusable because some controller registers can only be written
when the clock is enabled via CLKGATE.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We met some channels in abnormal state after disable.
Reset it to get a clean state.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In general, the mxs-dma users get separate irq for each channel,
but gpmi is special one which has only one irq shared by all gpmi
channels. It causes mxs_dma channel allocation function fail for
all other gpmi channels except the first one calling into the
function.
The patch gets request_irq call skipped for NO_IRQ case, and leaves
this gpmi specific quirk to gpmi driver to sort out. It will fix
above problem if gpmi driver sets chan_irq as gpmi irq for only one
channel and NO_IRQ for all the rest channels.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds dma support for Freescale MXS-based SoC i.MX23/28,
including apbh-dma and apbx-dma.
* apbh-dma and apbx-dma are supported in the driver as two mxs-dma
instances.
* apbh-dma is different between mx23 and mx28, hardware version
register is used to differentiate.
* mxs-dma supports pio function besides data transfer. The driver
uses dma_data_direction DMA_NONE to identify the pio mode, and
steals sgl and sg_len to get pio words and numbers from clients.
* mxs dmaengine has some very specific features, like sense function
and the special NAND support (nand_lock, nand_wait4ready). These
are too specific to implemented in generic dmaengine driver.
* The driver refers to imx-sdma and only a single descriptor is
statically assigned to each channel.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
