I want to use it during station destruction as well
so rename it to WLAN_STA_BLOCK_BA which is also the
only use of it now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All callers of ieee80211_sta_stop_rx_ba_session can
just call __ieee80211_stop_rx_ba_session instead
because they already have the station struct, so do
that and remove ieee80211_sta_stop_rx_ba_session.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All other places except one in the TX path, which
has BHs disabled, and it also cannot be locked from
interrupts so disabling IRQs is not necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station w/o a key is destroyed, or when
a driver submits work for a station and thereby
references it again, it seems like potentially
we could reference the station structure while
it is being destroyed.
Wait for an RCU grace period to elapse before
finishing destroying the station after we have
removed the station from the driver and from
the hash table etc., even in the case where no
key is associated with the station.
Also, there's no point in deleting the plink
timer here since it'll be properly deleted just
a bit later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 is quite strict on allowing authentication and association
commands only in certain states. In order to meet these requirements,
user space applications may need to clear authentication or
association state in some cases. Currently, this can be done with
deauth/disassoc command, but that ends up sending out Deauthentication
or Disassociation frame unnecessarily. Add a new nl80211 attribute to
allow this sending of the frame be skipped, but with all other
deauth/disassoc operations being completed.
Similar state change is also needed for IEEE 802.11r FT protocol in
the FT-over-DS case which does not use Authentication frame exchange
in a transition to another BSS. For this to work with cfg80211, an
authentication entry needs to be created for the target BSS without
sending out an Authentication frame. The nl80211 authentication
command can be used for this purpose, too, with the new attribute to
indicate that the command is only for changing local state. This
enables wpa_supplicant to complete FT-over-DS transition successfully.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit e34e09401ee9888dd662b2fca5d607794a56daf2 incorrectly removed
use of ieee80211_has_protected() from the management frame case and in
practice, made this validation drop all Action frames when MFP is
enabled. This should have only been done for frames with Protected
field set to zero.
Signed-off-by: Jouni Malinen <j@w1.fi>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit bef5d1c70d split
ieee80211_drop_unencrypted() into separate functions that are used for
Data and Management frames. However, it did not handle the
RX_FLAG_DECRYPTED correctly for Management frames:
ieee80211_drop_unencrypted() can only return 0 for Management frames,
so there is no point in calling it here. Instead, just check the
status->flag directly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iw dev <devname> station del <MAC address> is quiet useful in mesh mode and should be possible.
Signed-off-by: Marco Porsch <marco.porsch@siemens.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When selecting the RX key for group-addressed robust management
frames, we do not actually select any BIP key if the frame is
unprotected (since we cannot find the key index from MMIE). This
results in the drop_unencrypted check in failing to drop the frame. It
is enough to verify that we have a STA entry for the transmitter and
that MFP is enabled for that STA; we do not need to check rx->key
here. This fixes BIP processing for unprotected, group-addressed,
robust management frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BIP (part of IEEE 802.11w) is only supposed to be used with
group-addressed frames. We ended up picking it as a default mechanism
for every management whenever we did not have a STA entry for the
destination (e.g., for Probe Response to a STA that is not
associated). While the extra MMIE in the end of management frames
should not break frames completed in most cases, there is no point in
doing this. Fix key selection to pick the default management key only
if the frame is sent to multicast/broadcast address and the frame is a
robust management frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When management frame protection (IEEE 802.11w) is used, the
deauthentication and disassociation frames must be protected whenever
the encryption keys are configured. We were removing the STA entry and
with it, the keys, just before actually sending out these frames which
meant that the frames went out unprotected. The AP will drop them in
such a case. Fix this by reordering the operations a bit so that
sta_info_destroy_addr() gets called only after
ieee80211_send_deauth_disassoc().
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calculate a running average of the signal strength reported for Beacon
frames and indicate cqm events if the average value moves below or
above the configured threshold value (and filter out repetitive events
with by using the configured hysteresis).
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable QoS explicitly, when user space AP program will setup a QoS
queues. Currently this is not needed as iwlwifi not work in AP mode
and no other driver implement enable/disable QoS.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add interface to disable/enable QoS (aka WMM or WME). Currently drivers
enable it explicitly when ->conf_tx method is called, and newer disable.
Disabling is needed for some APs, which do not support QoS, such
we should send QoS frames to them.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mac80211 drivers can now pass paged SKBs to mac80211 via
ieee80211_rx{_irqsafe}. The implementation currently use
skb_linearize() in a few places i.e. management frame
handling, software decryption, defragmentation and A-MSDU
process. We will optimize them one by one later.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Cc: Kalle Valo <kalle.valo@iki.fi>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need "sdata" any more after:
d84f323477
mac80211: remove dev_hold/put calls
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for the set_cqm_config op. This op function configures the
requested connection quality monitor rssi threshold and rssi hysteresis
values to the hardware if the hardware supports
IEEE80211_HW_SUPPORTS_CQM.
For unsupported hardware, currently -EOPNOTSUPP is returned, so the mac80211
is currently not doing connection quality monitoring on the host. This could be
added later, if needed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for basic configuration of a connection quality monitoring to the
nl80211 interface, and basic support for notifying about triggered monitoring
events.
Via this interface a user-space connection manager may configure and receive
pre-warning events of deteriorating WLAN connection quality, and start
preparing for roaming in advance, before the connection is already lost.
An example usage of such a trigger is starting scanning for nearby AP's in
an attempt to find one with better connection quality, and associate to it
before the connection characteristics of the existing connection become too bad
or the association is even lost, leading in a prolonged delay in connectivity.
The interface currently supports only RSSI, but it could be later extended
to include other parameters, such as signal-to-noise ratio, if need for that
arises.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on a RFC patch by Kalle Valo.
The wl1271 has a feature which handles the connection monitor logic
in hardware, basically sending periodically nullfunc frames and reporting
to the host if AP is lost, after attempting to recover by sending
probe-requests to the AP.
Add support to mac80211 by adding a new flag IEEE80211_HW_CONNECTION_MONITOR
which prevents conn_mon_timer from triggering during idle periods, and
prevents sending probe-requests to the AP if beacon-loss is indicated by the
hardware.
Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a wireless.h macro for this, might as well use it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a wireless.h macro for this, might as well use it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames the (never officially released) sysfs-knobs
"blocked_hw" and "blocked_sw" to "hard" and "soft", as the hardware vs
software conotation is misleading.
It also gets rid of not needed locks around u32-read-access.
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when an IBSS merge happened, the supported rates for the newly added station
were left empty, causing the rate control module to be initialized with only
the basic rates.
the section of the ibss code which deals with updating supported rates for
an already existing station failed to inform the rate control module about the
new rates. as both minstrel and pid don't have an update function i just use
the init function.
also remove unnecessary (unsigned long long) casts and edit debug message.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a cooked monitor interface is active, ieee80211_tx_status()
generates a radiotap header for every single frame, even if it wasn't
injected and thus won't be sent to a monitor interface.
This patch reduces cpu utilization by moving the cooked monitor check a
bit earlier, before it generates the rtap header.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes it possible to reuse the minstrel rate control ops
from another rate control module. This is useful in preparing for the
new 802.11n implementation of minstrel, which will reuse the old code
for legacy stations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up the debugfs read function for the statistics by
using simple_read_from_buffer instead of its own semi-broken hack.
Also removes a useless member of the minstrel debugfs info struct.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I discovered that if EMBEDDED=y, one can accidentally build a mac80211 stack
and drivers w/ no rate control algorithm. For drivers like RTL8187 that don't
supply their own RC algorithms, this will cause ieee80211_register_hw to
fail (making the driver unusable).
This will tell kconfig to provide a warning if no rate control algorithms
have been selected. That'll at least warn the user; users that know that
their drivers supply a rate control algorithm can safely ignore the
warning, and those who don't know (or who expect to be using multiple
drivers) can select a default RC algorithm.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This commit introduces two new sysfs knobs.
/sys/class/rfkill/rfkill[0-9]+/blocked_hw: (ro)
hardblock kill state
/sys/class/rfkill/rfkill[0-9]+/blocked_sw: (rw)
softblock kill state
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers can now advertise to cfg80211 that they have
multiple MAC addresses reserved for a device, but we
don't currently make use of that in mac80211.
Change that and assign different addresses to new
virtual interfaces (if addresses are available) in
order to make it easier for users to use multiple
virtual interfaces; they no longer need to always
assign a new MAC address manually.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current software scan implemenation in mac80211 returns to the operating
channel after each scanned channel. However, in some situations (e.g. no
traffic) it would be nicer to scan a few channels in a row to speed up
the scan itself.
Hence, after scanning a channel, check if we have queued up any tx frames and
return to the operating channel in that case.
Unfortunately we don't know if the AP has buffered any frames for us. Hence,
scan only as many channels in a row as the pm_qos latency and the negotiated
listen interval allows us to.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when an IBSS merge happened, the supported rates for the newly added station
were left empty, causing the rate control module to be initialized with only
the basic rates.
also the section of the ibss code which deals with updating supported rates for
an already existing station fails to inform the rate control module about the
new rates. as i don't know how to fix this (minstrel does not have an update
function), i have just added a comment for now.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noise value as is won't be used, isn't
filled by most drivers and doesn't really
make a whole lot of sense on a per packet
basis -- proper cfg80211 survey support in
mac80211 will need to be different.
Mark the struct member as deprecated so it
will be removed from drivers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.
This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.
Fix this by passing the new channel type to the driver.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit e1dd33f60ced091114e4aacf141e0d03b88d3e13 changed cfg80211 to
allow association commands while in associated state to enable support
for roaming within an ESS. However, this was not enough to resolve all
cases with mac80211 which needs some additional handling of the
reassociation case to clear internal state with the BSS that was in use
previously.
This patch makes ieee80211_mgd_assoc() accept a valid reassociation
command and clean the association state with the previous BSS. This
fixes roaming between BSSes in an ESS when using wpa_supplicant with
-Dnl80211.
Signed-off-by: Jouni Malinen <j@w1.fi>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for handling KEY_RFKILL in the rfkill input module. This
simply toggles the state of all rfkill devices. The comment in rfkill.h
is also updated to reflect that RFKILL_TYPE_ALL may be used inside the
kernel.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the following build error when IGMP_SNOOPING is not enabled.
In file included from net/bridge/br.c:24:
net/bridge/br_private.h: In function 'br_multicast_is_router':
net/bridge/br_private.h:361: error: 'struct net_bridge' has no member named 'multicast_router'
net/bridge/br_private.h:362: error: 'struct net_bridge' has no member named 'multicast_router'
net/bridge/br_private.h:363: error: 'struct net_bridge' has no member named 'multicast_router_timer'
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use scm_send and scm_recv on both unix domain and
netlink sockets, but only unix domain sockets support
everything required for file descriptor passing,
so error if someone attempts to pass file descriptors
over netlink sockets.
Cc: stable@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (44 commits)
rcu: Fix accelerated GPs for last non-dynticked CPU
rcu: Make non-RCU_PROVE_LOCKING rcu_read_lock_sched_held() understand boot
rcu: Fix accelerated grace periods for last non-dynticked CPU
rcu: Export rcu_scheduler_active
rcu: Make rcu_read_lock_sched_held() take boot time into account
rcu: Make lockdep_rcu_dereference() message less alarmist
sched, cgroups: Fix module export
rcu: Add RCU_CPU_STALL_VERBOSE to dump detailed per-task information
rcu: Fix rcutorture mod_timer argument to delay one jiffy
rcu: Fix deadlock in TREE_PREEMPT_RCU CPU stall detection
rcu: Convert to raw_spinlocks
rcu: Stop overflowing signed integers
rcu: Use canonical URL for Mathieu's dissertation
rcu: Accelerate grace period if last non-dynticked CPU
rcu: Fix citation of Mathieu's dissertation
rcu: Documentation update for CONFIG_PROVE_RCU
security: Apply lockdep-based checking to rcu_dereference() uses
idr: Apply lockdep-based diagnostics to rcu_dereference() uses
radix-tree: Disable RCU lockdep checking in radix tree
vfs: Abstract rcu_dereference_check for files-fdtable use
...
NETIF_F_NTUPLE flag setting introduced a bug: non-ntuple flags
like LRO may be successfully set, before ioctl(2) returns failure
to userspace.
The set-flags operation should be all-or-none, rather than leaving
things in an inconsistent state prior to reporting failure to
userspace.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Inode field in /proc/net/{tcp,udp,packet,raw,...} is useful to know the types of
file descriptors associated to a process. Actually lsof utility uses the field.
Unfortunately, unlike /proc/net/{tcp,udp,packet,raw,...}, /proc/net/netlink doesn't have the field.
This patch adds the field to /proc/net/netlink.
Signed-off-by: Masatake YAMATO <yamato@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the user to the IGMP parameters related to the
snooping function of the bridge. This includes various time
values and retransmission limits.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the user to control the hash elasticity/max
parameters. The elasticity setting does not take effect until
the next new multicast group is added. At which point it is
checked and if after rehashing it still can't be satisfied then
snooping will be disabled.
The max setting on the other hand takes effect immediately. It
must be a power of two and cannot be set to a value less than the
current number of multicast group entries. This is the only way
to shrink the multicast hash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the user to disable IGMP snooping completely
through a sysfs toggle. It also allows the user to reenable
snooping when it has been automatically disabled due to hash
collisions. If the collisions have not been resolved however
the system will refuse to reenable snooping.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the user to forcibly enable/disable ports as
having multicast routers attached. A port with a multicast router
will receive all multicast traffic.
The value 0 disables it completely. The default is 1 which lets
the system automatically detect the presence of routers (currently
this is limited to picking up queries), and 2 means that the port
will always receive all multicast traffic.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch finally hooks up the multicast snooping module to the
data path. In particular, all multicast packets passing through
the bridge are fed into the module and switched by it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
