that need review and did not make it.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQRPfPO7r0eAhk010v0w5/Bqldv68gUCYj+mOQAKCRAw5/Bqldv6
8pXqAJ9co9nkfU7H+VIdk4FWHp6w87fDCACeKRIOcG5eK50yoBhMGclvuuC7V5s=
=gSle
-----END PGP SIGNATURE-----
Merge tag 'leds-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"Nothing major here, there are two drivers that need review and did not
make it into this round"
* tag 'leds-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: pca955x: Allow zero LEDs to be specified
leds: pca955x: Make the gpiochip always expose all pins
leds: simatic-ipc-leds: Don't directly deref ioremap_resource() returned ptr
leds: simatic-ipc-leds: Make simatic_ipc_led_mem_res static
leds: lm3692x: Return 0 from remove callback
leds: sgm3140: Add ocs,ocp8110 compatible
dt-bindings: vendor-prefixes: Add ocs prefix
dt-bindings: leds: common: fix unit address in max77693 example
It's valid to use the PCA955x devices just for GPIOs and not for LEDs.
In this case, as PCA955X_TYPE_GPIO is now equivalent to
PCA955X_TYPE_NONE, remove the test for whether we have any child nodes
specified in the devicetree.
A consequence of this is it's now possible to bind the driver to a
PCA955x device when dynamically instantiated through the I2C subsystem's
`new_device` interface.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The devicetree binding allows specifying which pins are GPIO vs LED.
Limiting the instantiated gpiochip to just these pins as the driver
currently does requires an arbitrary mapping between pins and GPIOs, but
such a mapping is not implemented by the driver. As a result,
specifying GPIOs in such a way that they don't map 1-to-1 to pin indexes
does not function as expected.
Establishing such a mapping is more complex than not and even if we did,
doing so leads to a slightly hairy userspace experience as the behaviour
of the PCA955x gpiochip would depend on how the pins are assigned in the
devicetree. Instead, always expose all pins via the gpiochip to provide
a stable interface and track which pins are in use.
Specifying a pin as `type = <PCA955X_TYPE_GPIO>;` in the devicetree
becomes a no-op.
I've assessed the impact of this change by looking through all of the
affected devicetrees as of the tag leds-5.15-rc1:
```
$ git grep -l 'pca955[0123]' $(find . -name dts -type d)
arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts
arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts
arch/arm/boot/dts/aspeed-bmc-opp-swift.dts
arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts
arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts
```
These are all IBM-associated platforms. I've analysed both the
devicetrees and schematics where necessary to determine whether any
systems hit the hazard of the current broken behaviour. For the most
part, the systems specify the pins as either all LEDs or all GPIOs, or
at least do so in a way such that the broken behaviour isn't exposed.
The main counter-point to this observation is the Everest system whose
devicetree describes a large number of PCA955x devices and in some cases
has pin assignments that hit the hazard. However, there does not seem to
be any use of the affected GPIOs in the userspace associated with
Everest.
Regardless, any use of the hazardous GPIOs in Everest is already broken,
so let's fix the interface and then fix any already broken userspace
with it.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Sparse (rightly) currently gives the following warning:
drivers/leds/simple/simatic-ipc-leds.c:155:40:
sparse: sparse: incorrect type in assignment (different address spaces)
expected void *static [toplevel] simatic_ipc_led_memory
got void [noderef] __iomem *
Fix this by changing the type of simatic_ipc_led_memory to void __iomem *
and use readl()/writel() to access it.
Cc: Henning Schild <henning.schild@siemens.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Gerd Haeussler <gerd.haeussler.ext@siemens.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
simatic_ipc_led_mem_res is not used outside of the driver, make it static.
Cc: Henning Schild <henning.schild@siemens.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The only difference between returning zero or a non-zero value is that
for the non-zero case the i2c will print a generic error message
("remove failed (-ESOMETHING), will be ignored").
In this case however the driver itself already emitted a more helpful
error message, so the additional error message isn't helpful at all.
The long-term goal is to make the i2c remove callback return void, making
all implementations return 0 is preparatory work for this change.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
I had to rebase at last moment to fix wrong author of one
commit. Sorry about that.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQRPfPO7r0eAhk010v0w5/Bqldv68gUCYd8hdwAKCRAw5/Bqldv6
8m3sAKC20ddEFW04Mk45Tw72qSyud6vhwQCaAnQy6dcd+zV6LOxosgLZdtXkvx0=
=CU+X
-----END PGP SIGNATURE-----
Merge tag 'leds-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"Nothing major is happening here"
* tag 'leds-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: lp55xx: initialise output direction from dts
ARM: dts: omap3-n900: Fix lp5523 for multi color
leds: ktd2692: Drop calling dev_of_node() in ktd2692_parse_dt
leds: lgm-sso: Get rid of duplicate of_node assignment
leds: tca6507: Get rid of duplicate of_node assignment
leds: leds-fsg: Drop FSG3 LED driver
leds: lp50xx: remove unused variable
dt-bindings: leds: Replace moonlight with indicator in mt6360 example
leds: led-core: Update fwnode with device_set_node
leds: tca6507: use swap() to make code cleaner
leds: Add mt6360 driver
dt-bindings: leds: Add bindings for MT6360 LED
Commit a5d3d1adc9 ("leds: lp55xx: Initialize enable GPIO direction to
output") attempts to fix this, but the fix did not work since at least
for the Nokia N900 the value needs to be set to HIGH, per the device
tree. So rather than hardcoding the value to a potentially invalid value
for some devices, let's set direction in lp55xx_init_device.
Fixes: a5d3d1adc9 ("leds: lp55xx: Initialize enable GPIO direction to output")
Fixes: 92a81562e6 ("leds: lp55xx: Add multicolor framework support to lp55xx")
Fixes: ac219bf3c9 ("leds: lp55xx: Convert to use GPIO descriptors")
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
output of dev_of_node() is already assigned to "np" variable in
ktd2692_parse_dt(). Use "np" variable to check if OF node is NULL
instead of calling dev_of_node() again.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
GPIO library does copy the of_node from the parent device of
the GPIO chip, there is no need to repeat this in the individual
drivers. Remove assignment here.
For the details one may look into the of_gpio_dev_init() implementation.
Call graph:
--> sso_gpio_gc_init()
--> devm_gpiochip_add_data
--> devm_gpiochip_add_data_with_key
--> gpiochip_add_data_with_key()
--> of_gpio_dev_init()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
GPIO library does copy the of_node from the parent device of
the GPIO chip, there is no need to repeat this in the individual
drivers. Remove assignment here.
For the details one may look into the of_gpio_dev_init() implementation.
Call graph:
--> tca6507_probe_gpios()
--> gpiochip_add_data()
--> gpiochip_add_data_with_key()
--> of_gpio_dev_init()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The board file using this driver has been deleted and the
FSG3 LEDs can be modeled using a system controller and some
register bit LEDs in the device tree so this driver is no
longer needed.
Reported-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Cc: Krzysztof Hałasa <khalasa@piap.pl>
Cc: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
During code review this unused variable was found. Remove it.
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Update a newly created device's fwnode and of_node pointers using the
recently added device_set_node helper. This keeps some firmware node
specifics out of led-class and should help tracking future changes
regarding device firmware node updates.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Use the macro 'swap()' defined in 'include/linux/minmax.h' to avoid
opencoding it.
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Add MT6360 LED driver include 2-channel Flash LED with torch/strobe mode,
3-channel RGB LED support Register/Flash/Breath Mode, and 1-channel for
moonlight LED.
Signed-off-by: Gene Chen <gene_chen@richtek.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
This driver adds initial support for several devices from Siemens. It is
based on a platform driver introduced in an earlier commit.
One of the supported machines has GPIO connected LEDs, here we poke GPIO
memory directly because pinctrl does not come up.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/20211213120502.20661-3-henning.schild@siemens.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The CPU trigger is invoked on ARM from CPU-idle. That trigger later
invokes led_trigger_event() which may invoke the callback of the actual driver.
That driver can acquire a spinlock_t which is okay on kernel without
PREEMPT_RT. On a PREEMPT_RT enabled kernel this lock is turned into a
sleeping lock and must not be acquired with disabled interrupts.
Disable the CPU trigger on PREEMPT_RT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lkml.kernel.org/r/20210924111501.m57cwwn7ahiyxxdd@linutronix.de
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Even with the previous commit 27af8e2c90
("leds: trigger: fix potential deadlock with libata")
to this file, we still get lockdep unhappy, and Boqun
explained the report here:
https://lore.kernel.org/r/YNA+d1X4UkoQ7g8a@boqun-archlinux
Effectively, this means that the read_lock_irqsave() isn't
enough here because another CPU might be trying to do a
write lock, and thus block the readers.
This is all pretty messy, but it doesn't seem right that
the LEDs framework imposes some locking requirements on
users, in particular we'd have to make the spinlock in the
iwlwifi driver always disable IRQs, even if we don't need
that for any other reason, just to avoid this deadlock.
Since writes to the led_cdevs list are rare (and are done
by userspace), just switch the list to RCU. This costs a
synchronize_rcu() at removal time so we can ensure things
are correct, but that seems like a small price to pay for
getting lock-free iterations and no deadlocks (nor any
locking requirements imposed on users.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
gcc-11 warns when building with W=1:
drivers/leds/led-class-flash.c: In function 'flash_fault_show':
drivers/leds/led-class-flash.c:210:16: error: 'sprintf' argument 3 overlaps destination object 'buf' [-Werror=restrict]
210 | return sprintf(buf, "%s\n", buf);
| ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/leds/led-class-flash.c:187:54: note: destination object referenced by 'restrict'-qualified argument 1 was declared here
187 | struct device_attribute *attr, char *buf)
| ~~~~~~^~~
There is no need for the sprintf() here when a strcat() does
the same thing without invoking undefined behavior.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The deprecated i2c probe functionality doesn't work with OF
compatible strings, as it only checks for the i2c device id. Switch
to the new way of probing and grab the match data to select the
chip type.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Much of the fwnode processing in the PCA955x driver is now in the
LEDs core driver, so pass the fwnode in the init data when
registering the LED device. In order to preserve the existing naming
scheme, check for an empty name and set it to the LED number.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
In order to retain the LED state after a system reboot, check the
documented default-state device tree property during initialization.
Modify the behavior of the probe according to the property.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Format the code. Add some variables to help shorten lines.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Read the retain-state-shutdown device tree property to set the
existing LED_RETAIN_AT_SHUTDOWN flag. Then check the flag when
unregistering, and if set, don't set the brightness to OFF. This
is useful for systems that want to keep the HW state of the LED
across reboots.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Commit b7fb14d3ac ("ide: remove the legacy ide driver") removes the
definition of the config IDE_GD_ATA.
So, remove the obsolete reference in ./drivers/leds/trigger/Kconfig.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The 9-channel one is called LP5009, not LP509.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
This patch adds support for "default-state" devicetree property, which
allows to defer pwm init to first use of led.
This allows to configure the PWM early in bootloader to let the LED
blink until an application in Linux userspace sets something different.
Signed-off-by: Denis Osterland-Heim <Denis.Osterland@diehl.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
This patch introduces a new function to read initial
default_state from fwnode.
Suggested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Denis Osterland-Heim <Denis.Osterland@diehl.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Adjust initialization not to trigger Coverity warnings.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The one of the latest change to the driver reveals the problem that
the error codes from callee aren't propagated to the caller of
__sso_led_dt_parse(). Fix this accordingly.
Fixes: 9999908ca1 ("leds: lgm-sso: Put fwnode in any case during ->probe()")
Fixes: c3987cd2bc ("leds: lgm: Add LED controller driver for LGM SoC")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Some 2-in-1s with a detachable (USB) keyboard(dock) have mute-LEDs in
the speaker- and/or mic-mute keys on the keyboard.
Examples of this are the Lenovo Thinkpad10 tablet (with its USB kbd-dock)
and the HP x2 10 series.
The detachable nature of these keyboards means that the keyboard and
thus the mute LEDs may show up after the user (or userspace restoring
old mixer settings) has muted the speaker and/or mic.
Current LED-class devices with a default_trigger of "audio-mute" or
"audio-micmute" initialize the brightness member of led_classdev with
ledtrig_audio_get() before registering the LED.
This makes the software state after attaching the keyboard match the
actual audio mute state, e.g. cat /sys/class/leds/foo/brightness will
show the right value.
But before this commit nothing was actually calling the led_classdev's
brightness_set[_blocking] callback so the value returned by
ledtrig_audio_get() was never actually being sent to the hw, leading
to the mute LEDs staying in their default power-on state, after
attaching the keyboard, even if ledtrig_audio_get() returned a different
state.
This could be fixed by having the individual LED drivers call
brightness_set[_blocking] themselves after registering the LED,
but this really is something which should be done by a led-trigger
activate callback.
Add an activate callback for this, fixing the issue of the
mute LEDs being out of sync after (re)attaching the keyboard.
Cc: Takashi Iwai <tiwai@suse.de>
Fixes: faa2541f5b ("leds: trigger: Introduce audio mute LED trigger")
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
fwnode_get_next_available_child_node() bumps a reference counting of
a returned variable. We have to balance it whenever we return to
the caller.
Fixes: e1c6edcbea ("leds: rt8515: Add Richtek RT8515 LED driver")
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
device_get_next_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
Fixes: 8cd7d6daba ("leds: lt3593: Add device tree probing glue")
Cc: Daniel Mack <daniel@zonque.org>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
It's easy to miss necessary clean up, e.g. firmware node reference counting,
during error path in ->probe(). Make it more robust by moving to a single
point of return.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Currently the headers to be included look rather like a random set.
Update them a bit to reflect the reality.
While at it, drop unneeded dependcy to OF.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
There is no user of of*.h headers, but mod_devicetable.h.
Update header block accordingly.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Convert to use list_for_each_entry*() API insted of open coded variants.
It saves few lines of code and makes iteasier to read and maintain.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The idea of managed resources is that they will be cleaned up automatically
and in the proper order. Remove explicit GPIO cleanup.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
When requesting GPIO line the probe can be deferred.
In such case don't spam logs with an error message.
This can be achieved by switching to dev_err_probe().
Fixes: c3987cd2bc ("leds: lgm: Add LED controller driver for LGM SoC")
Cc: Amireddy Mallikarjuna reddy <mallikarjunax.reddy@linux.intel.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
fwnode_get_next_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
All the same in fwnode_for_each_child_node() case.
Fixes: c3987cd2bc ("leds: lgm: Add LED controller driver for LGM SoC")
Cc: Amireddy Mallikarjuna reddy <mallikarjunax.reddy@linux.intel.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
There is no user of of*.h headers, but mod_devicetable.h.
Update header block accordingly.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'ret'.
Eliminate the follow smatch warning:
drivers/leds/leds-is31fl32xx.c:388 is31fl32xx_parse_dt() warn: missing
error code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Fixes: 9d7cffaf99 ("leds: Add driver for the ISSI IS31FL32xx family of LED controllers")
Acked-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Cc: Ingi Kim <ingi2.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Cc: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
