Commit Graph

109 Commits

Author SHA1 Message Date
Andre Noll
ac5e7113e7 md: Push down data integrity code to personalities.
This patch replaces md_integrity_check() by two new public functions:
md_integrity_register() and md_integrity_add_rdev() which are both
personality-independent.

md_integrity_register() is called from the ->run and ->hot_remove
methods of all personalities that support data integrity.  The
function iterates over the component devices of the array and
determines if all active devices are integrity capable and if their
profiles match. If this is the case, the common profile is registered
for the mddev via blk_integrity_register().

The second new function, md_integrity_add_rdev() is called from the
->hot_add_disk methods, i.e. whenever a new device is being added
to a raid array. If the new device does not support data integrity,
or has a profile different from the one already registered, data
integrity for the mddev is disabled.

For raid0 and linear, only the call to md_integrity_register() from
the ->run method is necessary.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-08-03 10:59:47 +10:00
Martin K. Petersen
8f6c2e4b32 md: Use new topology calls to indicate alignment and I/O sizes
Switch MD over to the new disk_stack_limits() function which checks for
aligment and adjusts preferred I/O sizes when stacking.

Also indicate preferred I/O sizes where applicable.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-07-01 11:13:45 +10:00
Andre Noll
8c6ac868b1 md: Push down reconstruction log message to personality code.
Currently, the md layer checks in analyze_sbs() if the raid level
supports reconstruction (mddev->level >= 1) and if reconstruction is
in progress (mddev->recovery_cp != MaxSector).

Move that printk into the personality code of those raid levels that
care (levels 1, 4, 5, 6, 10).

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-18 08:48:06 +10:00
Andre Noll
9d8f036362 md: Make mddev->chunk_size sector-based.
This patch renames the chunk_size field to chunk_sectors with the
implied change of semantics.  Since

	is_power_of_2(chunk_size) = is_power_of_2(chunk_sectors << 9)
				  = is_power_of_2(chunk_sectors)

these bits don't need an adjustment for the shift.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-18 08:45:01 +10:00
raz ben yehuda
964e7913b0 md: raid10: chunk size check in run
have raid10 check chunk size in run method instead of in md

Signed-off-by: raziebe@gmail.com
Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-16 17:01:22 +10:00
NeilBrown
070ec55d07 md: remove mddev_to_conf "helper" macro
Having a macro just to cast a void* isn't really helpful.
I would must rather see that we are simply de-referencing ->private,
than have to know what the macro does.

So open code the macro everywhere and remove the pointless cast.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-06-16 16:54:21 +10:00
Martin K. Petersen
ae03bf639a block: Use accessor functions for queue limits
Convert all external users of queue limits to using wrapper functions
instead of poking the request queue variables directly.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-22 23:22:54 +02:00
NeilBrown
1805556912 md/raid10: don't clear bitmap during recovery if array will still be degraded.
If we have a raid10 with multiple missing devices, and we recover just
one of these to a spare, then we risk (depending on the bitmap and
array chunk size) clearing bits of the bitmap for which recovery isn't
complete (because a device is still missing).

This can lead to a subsequent "re-add" being recovered without
any IO happening, which would result in loss of data.

This patch takes the safe approach of not clearing bitmap bits
if the array will still be degraded.

This patch is suitable for all active -stable kernels.

Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
2009-05-07 12:48:10 +10:00
Christoph Hellwig
8f3d8ba20e block: move bio list helpers into bio.h
It's used by DM and MD and generally useful, so move the bio list
helpers into bio.h.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-04-15 08:28:09 +02:00
Dan Williams
b522adcde9 md: 'array_size' sysfs attribute
Allow userspace to set the size of the array according to the following
semantics:

1/ size must be <= to the size returned by mddev->pers->size(mddev, 0, 0)
   a) If size is set before the array is running, do_md_run will fail
      if size is greater than the default size
   b) A reshape attempt that reduces the default size to less than the set
      array size should be blocked
2/ once userspace sets the size the kernel will not change it
3/ writing 'default' to this attribute returns control of the size to the
   kernel and reverts to the size reported by the personality

Also, convert locations that need to know the default size from directly
reading ->array_sectors to <pers>_size.  Resync/reshape operations
always follow the default size.

Finally, fixup other locations that read a number of 1k-blocks from
userspace to use strict_blocks_to_sectors() which checks for unsigned
long long to sector_t overflow and blocks to sectors overflow.

Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-03-31 15:00:31 +11:00
Dan Williams
1f403624bd md: centralize ->array_sectors modifications
Get personalities out of the business of directly modifying
->array_sectors.  Lays groundwork to introduce policy on when
->array_sectors can be modified.

Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-03-31 14:59:03 +11:00
Dan Williams
80c3a6ce4b md: add 'size' as a personality method
In preparation for giving userspace control over ->array_sectors we need
to be able to retrieve the 'default' size, and the 'anticipated' size
when a reshape is requested.  For personalities that do not reshape emit
a warning if anything but the default size is requested.

In the raid5 case we need to update ->previous_raid_disks to make the
new 'default' size available.

Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-03-31 14:57:49 +11:00
NeilBrown
409c57f380 md: enable suspend/resume of md devices.
To be able to change the 'level' of an md/raid array, we need to
suspend the device so that no requests are active - then move some
pointers around etc.

The code already keeps counts of active requests and the ->quiesce
function can be used to wait until those counts hit zero.
However the quiesce function blocks new requests once they are all
ready 'inside' the personality module, and that is too late if we want
to replace the personality modules.

So make all md requests come in through a common md_make_request
function that keeps track of how many requests have entered the
modules but may not yet be on the internal reference counts.
Allow md_make_request to be blocked when we want to suspend the
device, and make it possible to wait for all those in-transit requests
to be added to internal lists so that ->quiesce can wait for them.

There is still a problem that when a request completes, we drop the
ref count inside the personality code so there is a short time between
when the refcount hits zero, and when the personality code is no
longer being used.
The personality code never blocks (schedule or spinlock) between
dropping the refcount and exiting the routine, so this should be safe
(as put_module calls synchronize_sched() before unmapping the module
code).

Signed-off-by: NeilBrown <neilb@suse.de>
2009-03-31 14:39:39 +11:00
Andre Noll
58c0fed400 md: Make mddev->size sector-based.
This patch renames the "size" field of struct mddev_s to "dev_sectors"
and stores the number of 512-byte sectors instead of the number of
1K-blocks in it.

All users of that field, including raid levels 1,4-6,10, are adjusted
accordingly. This simplifies the code a bit because it allows to get
rid of a couple of divisions/multiplications by two.

In order to make checkpatch happy, some minor coding style issues
have also been addressed. In particular, size_store() now uses
strict_strtoull() instead of simple_strtoull().

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-03-31 14:33:13 +11:00
NeilBrown
43b2e5d86d md: move md_k.h from include/linux/raid/ to drivers/md/
It really is nicer to keep related code together..

Signed-off-by: NeilBrown <neilb@suse.de>
2009-03-31 14:33:13 +11:00
NeilBrown
bff61975b3 md: move lots of #include lines out of .h files and into .c
This makes the includes more explicit, and is preparation for moving
md_k.h to drivers/md/md.h

Remove include/raid/md.h as its only remaining use was to #include
other files.

Signed-off-by: NeilBrown <neilb@suse.de>
2009-03-31 14:33:13 +11:00
Christoph Hellwig
ef740c372d md: move headers out of include/linux/raid/
Move the headers with the local structures for the disciplines and
bitmap.h into drivers/md/ so that they are more easily grepable for
hacking and not far away.  md.h is left where it is for now as there
are some uses from the outside.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-03-31 14:27:03 +11:00
NeilBrown
73d5c38a95 md: avoid races when stopping resync.
There has been a race in raid10 and raid1 for a long time
which has only recently started showing up due to a scheduler changed.

When a sync_read request finishes, as soon as reschedule_retry
is called, another thread can mark the resync request as having
completed, so md_do_sync can finish, ->stop can be called, and
->conf can be freed.  So using conf after reschedule_retry is not
safe.

Similarly, when finishing a sync_write, calling md_done_sync must be
the last thing we do, as it allows a chain of events which will free
conf and other data structures.

The first of these requires action in raid10.c
The second requires action in raid1.c and raid10.c

Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
2009-02-25 13:18:47 +11:00
NeilBrown
78200d45cd md/raid10: Don't call bitmap_cond_end_sync when we are doing recovery.
For raid1/4/5/6, resync (fixing inconsistencies between devices) is
very similar to recovery (rebuilding a failed device onto a spare).
The both walk through the device addresses in order.

For raid10 it can be quite different.  resync follows the 'array'
address, and makes sure all copies are the same.  Recover walks
through 'device' addresses and recreates each missing block.

The 'bitmap_cond_end_sync' function allows the write-intent-bitmap
(When present) to be updated to reflect a partially completed resync.
It makes assumptions which mean that it does not work correctly for
raid10 recovery at all.

In particularly, it can cause bitmap-directed recovery of a raid10 to
not recovery some of the blocks that need to be recovered.

So move the call to bitmap_cond_end_sync into the resync path, rather
than being in the common "resync or recovery" path.


Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
2009-02-25 13:18:47 +11:00
NeilBrown
09b4068a7f md/raid10: Don't skip more than 1 bitmap-chunk at a time during recovery.
When doing recovery on a raid10 with a write-intent bitmap, we only
need to recovery chunks that are flagged in the bitmap.

However if we choose to skip a chunk as it isn't flag, the code
currently skips the whole raid10-chunk, thus it might not recovery
some blocks that need recovering.

This patch fixes it.

In case that is confusing, it might help to understand that there
is a 'raid10 chunk size' which guides how data is distributed across
the devices, and a 'bitmap chunk size' which says how much data
corresponds to a single bit in the bitmap.

This bug only affects cases where the bitmap chunk size is smaller
than the raid10 chunk size.



Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
2009-02-25 13:18:47 +11:00
Cheng Renquan
159ec1fc06 md: use list_for_each_entry macro directly
The rdev_for_each macro defined in <linux/raid/md_k.h> is identical to
list_for_each_entry_safe, from <linux/list.h>, it should be defined to
use list_for_each_entry_safe, instead of reinventing the wheel.

But some calls to each_entry_safe don't really need a safe version,
just a direct list_for_each_entry is enough, this could save a temp
variable (tmp) in every function that used rdev_for_each.

In this patch, most rdev_for_each loops are replaced by list_for_each_entry,
totally save many tmp vars; and only in the other situations that will call
list_del to delete an entry, the safe version is used.

Signed-off-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2009-01-09 08:31:08 +11:00
NeilBrown
a53a6c8575 md: fix bug in raid10 recovery.
Adding a spare to a raid10 doesn't cause recovery to start.
This is due to an silly type in
  commit 6c2fce2ef6
and so is a bug in 2.6.27 and .28-rc.

Thanks to Thomas Backlund for bisecting to find this.

Cc: Thomas Backlund <tmb@mandriva.org>
Cc: stable@kernel.org

Signed-off-by: NeilBrown <neilb@suse.de>
2008-11-06 17:28:20 +11:00
Stephen Rothwell
255707274e md: build failure due to missing delay.h
Today's linux-next build (powerpc ppc64_defconfig) failed like this:

drivers/md/raid1.c: In function 'sync_request':
drivers/md/raid1.c:1759: error: implicit declaration of function 'msleep_interruptible'
make[3]: *** [drivers/md/raid1.o] Error 1
make[3]: *** Waiting for unfinished jobs....
drivers/md/raid10.c: In function 'sync_request':
drivers/md/raid10.c:1749: error: implicit declaration of function 'msleep_interruptible'
make[3]: *** [drivers/md/raid10.o] Error 1
drivers/md/md.c: In function 'md_do_sync':
drivers/md/md.c:5915: error: implicit declaration of function 'msleep'

Caused by commit 6caa3b0bbdb474647f6bdd8a958ffc46f78d8d58 ("md: Remove
unnecessary #includes, #defines, and function declarations").  I added
the following patch.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-15 21:57:05 +11:00
NeilBrown
4bbf3771ca md: Relax minimum size restrictions on chunk_size.
Currently, the 'chunk_size' of an array must be at-least PAGE_SIZE.

This makes moving an array to a machine with a larger PAGE_SIZE, or
changing the kernel to use a larger PAGE_SIZE, can stop an array from
working.

For RAID10 and RAID4/5/6, this is non-trivial to fix as the resync
process works on whole pages at a time, and assumes them to be wholly
within a stripe.  For other raid personalities, this restriction is
not needed at all and can be dropped.

So remove the test on chunk_size from common can, and add it in just
the places where it is needed: raid10 and raid4/5/6.

Signed-off-by: NeilBrown <neilb@suse.de>
2008-10-13 11:55:12 +11:00
Denis ChengRq
6feef531f5 block: mark bio_split_pool static
Since all bio_split calls refer the same single bio_split_pool, the bio_split
function can use bio_split_pool directly instead of the mempool_t parameter;

then the mempool_t parameter can be removed from bio_split param list, and
bio_split_pool is only referred in fs/bio.c file, can be marked static.

Signed-off-by: Denis ChengRq <crquan@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:57:05 +02:00
Tejun Heo
074a7aca7a block: move stats from disk to part0
Move stats related fields - stamp, in_flight, dkstats - from disk to
part0 and unify stat handling such that...

* part_stat_*() now updates part0 together if the specified partition
  is not part0.  ie. part_stat_*() are now essentially all_stat_*().

* {disk|all}_stat_*() are gone.

* part_round_stats() is updated similary.  It handles part0 stats
  automatically and disk_round_stats() is killed.

* part_{inc|dec}_in_fligh() is implemented which automatically updates
  part0 stats for parts other than part0.

* disk_map_sector_rcu() is updated to return part0 if no part matches.
  Combined with the above changes, this makes NULL special case
  handling in callers unnecessary.

* Separate stats show code paths for disk are collapsed into part
  stats show code paths.

* Rename disk_stat_lock/unlock() to part_stat_lock/unlock()

While at it, reposition stat handling macros a bit and add missing
parentheses around macro parameters.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:08 +02:00
Tejun Heo
c995905916 block: fix diskstats access
There are two variants of stat functions - ones prefixed with double
underbars which don't care about preemption and ones without which
disable preemption before manipulating per-cpu counters.  It's unclear
whether the underbarred ones assume that preemtion is disabled on
entry as some callers don't do that.

This patch unifies diskstats access by implementing disk_stat_lock()
and disk_stat_unlock() which take care of both RCU (for partition
access) and preemption (for per-cpu counter access).  diskstats access
should always be enclosed between the two functions.  As such, there's
no need for the versions which disables preemption.  They're removed
and double underbars ones are renamed to drop the underbars.  As an
extra argument is added, there's no danger of using the old version
unconverted.

disk_stat_lock() uses get_cpu() and returns the cpu index and all
diskstat functions which access per-cpu counters now has @cpu
argument to help RT.

This change adds RCU or preemption operations at some places but also
collapses several preemption ops into one at others.  Overall, the
performance difference should be negligible as all involved ops are
very lightweight per-cpu ones.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:06 +02:00
Jens Axboe
960e739d9e block: raid fixups for removal of bi_hw_segments
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:03 +02:00
Mikulas Patocka
5df97b91b5 drop vmerge accounting
Remove hw_segments field from struct bio and struct request. Without virtual
merge accounting they have no purpose.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:03 +02:00
NeilBrown
0310fa216d Allow raid10 resync to happening in larger chunks.
The raid10 resync/recovery code currently limits the amount of
in-flight resync IO to 2Meg.  This was copied from raid1 where
it seems quite adequate.  However for raid10, some layouts require
a bit of seeking to perform a resync, and allowing a larger buffer
size means that the seeking can be significantly reduced.

There is probably no real need to limit the amount of in-flight
IO at all.  Any shortage of memory will naturally reduce the
amount of buffer space available down to a set minimum, and any
concurrent normal IO will quickly cause resync IO to back off.

The only problem would be that normal IO has to wait for all resync IO
to finish, so a very large amount of resync IO could cause unpleasant
latency when normal IO starts up.

So: increase RESYNC_DEPTH to allow 32Meg of buffer (if memory is
available) which seems to be a good amount.  Also reduce the amount
of memory reserved as there is no need to keep 2Meg just for resync if
memory is tight.

Thanks to Keld for the suggestion.

Cc: Keld Jørn Simonsen <keld@dkuug.dk>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-08-05 15:56:32 +10:00
Linus Torvalds
1e24b15b26 Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
  md: raid10: wake up frozen array
  md: do not count blocked devices as spares
  md: do not progress the resync process if the stripe was blocked
  md: delay notification of 'active_idle' to the recovery thread
  md: fix merge error
  md: move async_tx_issue_pending_all outside spin_lock_irq
2008-08-01 11:56:07 -07:00
Arthur Jones
388667bed5 md: raid10: wake up frozen array
When rescheduling a bio in raid10, we wake up
the md thread, but if the array is frozen, this
will have no effect.  This causes the array to
remain frozen for eternity.  We add a wake_up
to allow the array to de-freeze.  This code is
nearly identical to the raid1 code, which has
this fix already.

Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-08-01 12:55:14 +10:00
Linus Torvalds
8a392625b6 Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md: (52 commits)
  md: Protect access to mddev->disks list using RCU
  md: only count actual openers as access which prevent a 'stop'
  md: linear: Make array_size sector-based and rename it to array_sectors.
  md: Make mddev->array_size sector-based.
  md: Make super_type->rdev_size_change() take sector-based sizes.
  md: Fix check for overlapping devices.
  md: Tidy up rdev_size_store a bit:
  md: Remove some unused macros.
  md: Turn rdev->sb_offset into a sector-based quantity.
  md: Make calc_dev_sboffset() return a sector count.
  md: Replace calc_dev_size() by calc_num_sectors().
  md: Make update_size() take the number of sectors.
  md: Better control of when do_md_stop is allowed to stop the array.
  md: get_disk_info(): Don't convert between signed and unsigned and back.
  md: Simplify restart_array().
  md: alloc_disk_sb(): Return proper error value.
  md: Simplify sb_equal().
  md: Simplify uuid_equal().
  md: sb_equal(): Fix misleading printk.
  md: Fix a typo in the comment to cmd_match().
  ...
2008-07-21 10:29:12 -07:00
Andre Noll
f233ea5c9e md: Make mddev->array_size sector-based.
This patch renames the array_size field of struct mddev_s to array_sectors
and converts all instances to use units of 512 byte sectors instead of 1k
blocks.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
2008-07-21 17:05:22 +10:00
Alasdair G Kergon
cc371e66e3 Add bvec_merge_data to handle stacked devices and ->merge_bvec()
When devices are stacked, one device's merge_bvec_fn may need to perform
the mapping and then call one or more functions for its underlying devices.

The following bio fields are used:
  bio->bi_sector
  bio->bi_bdev
  bio->bi_size
  bio->bi_rw  using bio_data_dir()

This patch creates a new struct bvec_merge_data holding a copy of those
fields to avoid having to change them directly in the struct bio when
going down the stack only to have to change them back again on the way
back up.  (And then when the bio gets mapped for real, the whole
exercise gets repeated, but that's a problem for another day...)

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Milan Broz <mbroz@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-07-03 13:21:15 +02:00
Neil Brown
199050ea1f rationalise return value for ->hot_add_disk method.
For all array types but linear, ->hot_add_disk returns 1 on
success, 0 on failure.
For linear, it returns 0 on success and -errno on failure.

This doesn't cause a functional problem because the ->hot_add_disk
function of linear is used quite differently to the others.
However it is confusing.

So convert all to return 0 for success or -errno on failure
and fix call sites to match.

Signed-off-by: Neil Brown <neilb@suse.de>
2008-06-28 08:31:33 +10:00
Neil Brown
6c2fce2ef6 Support adding a spare to a live md array with external metadata.
i.e. extend the 'md/dev-XXX/slot' attribute so that you can
tell a device to fill an vacant slot in an and md array.

Signed-off-by: Neil Brown <neilb@suse.de>
2008-06-28 08:31:31 +10:00
Neil Brown
8c2e870a62 Ensure interrupted recovery completed properly (v1 metadata plus bitmap)
If, while assembling an array, we find a device which is not fully
in-sync with the array, it is important to set the "fullsync" flags.
This is an exact analog to the setting of this flag in hot_add_disk
methods.

Currently, only v1.x metadata supports having devices in an array
which are not fully in-sync (it keep track of how in sync they are).
The 'fullsync' flag only makes a difference when a write-intent bitmap
is being used.  In this case it tells recovery to ignore the bitmap
and recovery all blocks.

This fix is already in place for raid1, but not raid5/6 or raid10.

So without this fix, a raid1 ir raid4/5/6 array with version 1.x
metadata and a write intent bitmaps, that is stopped in the middle
of a recovery, will appear to complete the recovery instantly
after it is reassembled, but the recovery will not be correct.

If you might have an array like that, issueing
   echo repair > /sys/block/mdXX/md/sync_action

will make sure recovery completes properly.

Cc: <stable@kernel.org>
Signed-off-by: Neil Brown <neilb@suse.de>
2008-06-28 08:30:52 +10:00
NeilBrown
dfc7064500 md: restart recovery cleanly after device failure.
When we get any IO error during a recovery (rebuilding a spare), we abort
the recovery and restart it.

For RAID6 (and multi-drive RAID1) it may not be best to restart at the
beginning: when multiple failures can be tolerated, the recovery may be
able to continue and re-doing all that has already been done doesn't make
sense.

We already have the infrastructure to record where a recovery is up to
and restart from there, but it is not being used properly.
This is because:
  - We sometimes abort with MD_RECOVERY_ERR rather than just MD_RECOVERY_INTR,
    which causes the recovery not be be checkpointed.
  - We remove spares and then re-added them which loses important state
    information.

The distinction between MD_RECOVERY_ERR and MD_RECOVERY_INTR really isn't
needed.  If there is an error, the relevant drive will be marked as
Faulty, and that is enough to ensure correct handling of the error.  So we
first remove MD_RECOVERY_ERR, changing some of the uses of it to
MD_RECOVERY_INTR.

Then we cause the attempt to remove a non-faulty device from an array to
fail (unless recovery is impossible as the array is too degraded).  Then
when remove_and_add_spares attempts to remove the devices on which
recovery can continue, it will fail, they will remain in place, and
recovery will continue on them as desired.

Issue:  If we are halfway through rebuilding a spare and another drive
fails, and a new spare is immediately available,  do we want to:
 1/ complete the current rebuild, then go back and rebuild the new spare or
 2/ restart the rebuild from the start and rebuild both devices in
    parallel.

Both options can be argued for.  The code currently takes option 2 as
  a/ this requires least code change
  b/ this results in a minimally-degraded array in minimal time.

Cc: "Eivind Sarto" <ivan@kasenna.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-24 09:56:10 -07:00
Neil Brown
e7e72bf641 Remove blkdev warning triggered by using md
As setting and clearing queue flags now requires that we hold a spinlock
on the queue, and as blk_queue_stack_limits is called without that lock,
get the lock inside blk_queue_stack_limits.

For blk_queue_stack_limits to be able to find the right lock, each md
personality needs to set q->queue_lock to point to the appropriate lock.
Those personalities which didn't previously use a spin_lock, us
q->__queue_lock.  So always initialise that lock when allocated.

With this in place, setting/clearing of the QUEUE_FLAG_PLUGGED bit will no
longer cause warnings as it will be clear that the proper lock is held.

Thanks to Dan Williams for review and fixing the silly bugs.

Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Nick Piggin <npiggin@suse.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jacek Luczak <difrost.kernel@gmail.com>
Cc: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-14 19:11:15 -07:00
Harvey Harrison
cb6969e8cd misc: fix integer as NULL pointer warnings
drivers/md/raid10.c:889:17: warning: Using plain integer as NULL pointer
drivers/media/video/cx18/cx18-driver.c:616:12: warning: Using plain integer as NULL pointer
sound/oss/kahlua.c:70:12: warning: Using plain integer as NULL pointer

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-08 10:46:55 -07:00
Dan Williams
6bfe0b4990 md: support blocking writes to an array on device failure
Allows a userspace metadata handler to take action upon detecting a device
failure.

Based on an original patch by Neil Brown.

Changes:
-added blocked_wait waitqueue to rdev
-don't qualify Blocked with Faulty always let userspace block writes
-added md_wait_for_blocked_rdev to wait for the block device to be clear, if
 userspace misses the notification another one is sent every 5 seconds
-set MD_RECOVERY_NEEDED after clearing "blocked"
-kill DoBlock flag, just test mddev->external

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-30 08:29:33 -07:00
Nick Andrew
d7a420c947 raid: remove leading TAB on printk messages
MD drivers use one printk() call to print 2 log messages and the second line
may be prefixed by a TAB character.  It may also output a trailing space
before newline.  klogd (I think) turns the TAB character into the 2 characters
'^I' when logging to a file.  This looks ugly.

Instead of a leading TAB to indicate continuation, prefix both output lines
with 'raid:' or similar.  Also remove any trailing space in the vicinity of
the affected code and consistently end the sentences with a period.

Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:42 -07:00
K.Tanaka
a07e6ab41b md: the md RAID10 resync thread could cause a md RAID10 array deadlock
This message describes another issue about md RAID10 found by testing the
2.6.24 md RAID10 using new scsi fault injection framework.

Abstract:

When a scsi error results in disabling a disk during RAID10 recovery, the
resync threads of md RAID10 could stall.

This case, the raid array has already been broken and it may not matter.  But
I think stall is not preferable.  If it occurs, even shutdown or reboot will
fail because of resource busy.

The deadlock mechanism:

The r10bio_s structure has a "remaining" member to keep track of BIOs yet to
be handled when recovering.  The "remaining" counter is incremented when
building a BIO in sync_request() and is decremented when finish a BIO in
end_sync_write().

If building a BIO fails for some reasons in sync_request(), the "remaining"
should be decremented if it has already been incremented.  I found a case
where this decrement is forgotten.  This causes a md_do_sync() deadlock
because md_do_sync() waits for md_done_sync() called by end_sync_write(), but
end_sync_write() never calls md_done_sync() because of the "remaining" counter
mismatch.

For example, this problem would be reproduced in the following case:

Personalities : [raid10]
md0 : active raid10 sdf1[4] sde1[5](F) sdd1[2] sdc1[1] sdb1[6](F)
      3919616 blocks 64K chunks 2 near-copies [4/2] [_UU_]
      [>....................]  recovery =  2.2% (45376/1959808) finish=0.7min speed=45376K/sec

This case, sdf1 is recovering, sdb1 and sde1 are disabled.
An additional error with detaching sdd will cause a deadlock.

md0 : active raid10 sdf1[4] sde1[5](F) sdd1[6](F) sdc1[1] sdb1[7](F)
      3919616 blocks 64K chunks 2 near-copies [4/1] [_U__]
      [=>...................]  recovery =  5.0% (99520/1959808) finish=5.9min speed=5237K/sec

 2739 ?        S<     0:17 [md0_raid10]
28608 ?        D<     0:00 [md0_resync]
28629 pts/1    Ss     0:00 bash
28830 pts/1    R+     0:00 ps ax
31819 ?        D<     0:00 [kjournald]

The resync thread keeps working, but actually it is deadlocked.

Patch:
By this patch, the remaining counter will be decremented if needed.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:18 -08:00
NeilBrown
1c830532f6 md: fix possible raid1/raid10 deadlock on read error during resync
Thanks to K.Tanaka and the scsi fault injection framework, here is a fix for
another possible deadlock in raid1/raid10 error handing.

If a read request returns an error while a resync is happening and a resync
request is pending, the attempt to fix the error will block until the resync
progresses, and the resync will block until the read request completes.  Thus
a deadlock.

This patch fixes the problem.

Cc: "K.Tanaka" <k-tanaka@ce.jp.nec.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:18 -08:00
Keld Simonsen
8ed3a19563 md: don't attempt read-balancing for raid10 'far' layouts
This patch changes the disk to be read for layout "far > 1" to always be the
disk with the lowest block address.

Thus the chunks to be read will always be (for a fully functioning array) from
the first band of stripes, and the raid will then work as a raid0 consisting
of the first band of stripes.

Some advantages:

The fastest part which is the outer sectors of the disks involved will be
used.  The outer blocks of a disk may be as much as 100 % faster than the
inner blocks.

Average seek time will be smaller, as seeks will always be confined to the
first part of the disks.

Mixed disks with different performance characteristics will work better, as
they will work as raid0, the sequential read rate will be number of disks
involved times the IO rate of the slowest disk.

If a disk is malfunctioning, the first disk which is working, and has the
lowest block address for the logical block will be used.

Signed-off-by: Keld Simonsen <keld@dkuug.dk>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:18 -08:00
NeilBrown
a35e63efa1 md: fix deadlock in md/raid1 and md/raid10 when handling a read error
When handling a read error, we freeze the array to stop any other IO while
attempting to over-write with correct data.

This is done in the raid1d(raid10d) thread and must wait for all submitted IO
to complete (except for requests that failed and are sitting in the retry
queue - these are counted in ->nr_queue and will stay there during a freeze).

However write requests need attention from raid1d as bitmap updates might be
required.  This can cause a deadlock as raid1 is waiting for requests to
finish that themselves need attention from raid1d.

So we create a new function 'flush_pending_writes' to give that attention, and
call it in freeze_array to be sure that we aren't waiting on raid1d.

Thanks to "K.Tanaka" <k-tanaka@ce.jp.nec.com> for finding and reporting this
problem.

Cc: "K.Tanaka" <k-tanaka@ce.jp.nec.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-03-04 16:35:17 -08:00
NeilBrown
d089c6af10 md: change ITERATE_RDEV to rdev_for_each
As this is more in line with common practice in the kernel.  Also swap the
args around to be more like list_for_each.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:19 -08:00
NeilBrown
c620727779 md: allow a maximum extent to be set for resyncing
This allows userspace to control resync/reshape progress and synchronise it
with other activities, such as shared access in a SAN, or backing up critical
sections during a tricky reshape.

Writing a number of sectors (which must be a multiple of the chunk size if
such is meaningful) causes a resync to pause when it gets to that point.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:18 -08:00
NeilBrown
b47490c9bc md: Update md bitmap during resync.
Currently an md array with a write-intent bitmap does not updated that bitmap
to reflect successful partial resync.  Rather the entire bitmap is updated
when the resync completes.

This is because there is no guarentee that resync requests will complete in
order, and tracking each request individually is unnecessarily burdensome.

However there is value in regularly updating the bitmap, so add code to
periodically pause while all pending sync requests complete, then update the
bitmap.  Doing this only every few seconds (the same as the bitmap update
time) does not notciably affect resync performance.

[snitzer@gmail.com: export bitmap_cond_end_sync]
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Mike Snitzer" <snitzer@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06 10:41:18 -08:00