Use a #define for the usb vendor request type, clear the status
byte and use that instead of a magic offset in checking if idle.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unicast one wire replies back to the sender portid to avoid multiple
programs getting each other's messages, especially as the response
can't be uniquely identified with the sequence coming from the
requesting program when both programs generate the same id. Continue
to broadcast events such as add/remove master/slave devices.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows replying only to the requestor portid while still
supporting broadcasting. Pass 0 to portid for the previous behavior.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Netlink is a socket interface and is expected to be asynchronous.
Clients can now make w1 requests without blocking by making use of the
w1_master thread to process netlink commands which was previously only
used for doing an automatic bus search.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce new commands to add, remove, and list slave devices through
the netlink interface. This can be useful to skip the search on a
static network. They could previously only be added or removed
through automatic search or sysfs, and this allows a program to only
use netlink.
Only allocate memory when needed, so move kzalloc into w1_get_slaves
where it was used.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Search will detect at most max_slave_count devices per run, if there
are more pick up the next search where the previous left off.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1_max_slave_count is only used to abort the search early
or take a fast search (when 1), so there isn't any reason to not allow
it to be updated through sysfs. Memory is not allocated based on
the current value and 10 is a rather low base number, increasing to
64, and printing a message the first time the count is reached and
there were more devices to discover to let the user know why not
all the devices were found.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's valid to set the search count to 0 to stop searching, so don't
wake up the search thread to not search.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before 63706172f3 "rework kthread_stop()" kthread_should_stop()
always returned false when called from a non-kthread task, after it
would oops as a non-kthread didn't have that structure and netlink was
calling search from a thread which wasn't a kthread. 9d1817cab2
"w1: fix oops when w1_search is called from netlink connector",
modified the code to avoid calling kthread_stop from a netlink thread.
Introduce a w1_master flag and bit W1_ABORT_SEARCH to identify abort
to cleanly support both kthread and netlink search abort. A search
can take seconds to run, so it is important to abort early if the
hardware is removed in the middle of a search.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Marcin Jurkowski <marcin1j@gmail.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Sven Geggus <lists@fuchsschwanzdomain.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previous logic,
if (avail > 8) {
store slave;
return;
}
send data; clear;
The logic error is, if there isn't space send the buffer and clear,
but the slave wasn't added to the now empty buffer loosing that slave
id. It also should have been "if (avail >= 8)" because when it is 8,
there is space.
Instead, if there isn't space send and clear the buffer, then there is
always space for the slave id.
Signed-off-by: David Fries <David@Fries.net>
Cc: stable@vger.kernel.org
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Base frequency should be as close as possible to 1 MHz. This patch
adds warnings when clock is unreliable, according to i.MX datasheet.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Private field "clkdiv" is not used outside "probe", so there are
no reason to keep it in driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change to make
the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On architectures where long is more then 32 bits, modifying a 32-bit field
with set_bit (and other atomic bit operations) may cause bytes following
the field to by modified.
Because the endianness of the bits within a field is the native endianness
of the CPU[1], on big-endian machines, bit number zero is in the last byte
of the field.
Therefore, `set_bit(0, ptr)' on a 64-bit big-endian machine is roughly
equivalent to `((char *)ptr)[7] |= 1', and since w1 driver uses a 32-bit
field for holding the flags, this causes bytes beyond the field to be
modified.
[1] From Documentation/atomic_ops.txt:
Native atomic bit operations are defined to operate on objects
aligned to the size of an "unsigned long" C data type, and are
least of that size. The endianness of the bits within each
"unsigned long" are the native endianness of the cpu.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change to make
the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The first DT gpio is necessary for this driver, but errors returned for
of_get_gpio are ignored.
This patch adds a return value check for the first of_get_gpio.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
request_module for w1 slave modules needs to be called with the w1
master mutex unlocked. Because w1_attach_slave_device gets always(?)
called with mutex locked, we need to temporarily unlock the w1 master
mutex for the loading of the w1 slave module.
Signed-off by: Hans-Frieder Vogt <hfvogt@gmx.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a check to make sure that fops are only called if they have
been defined by the slave module.
Without this check modules like w1_smem cause a NULL pointer dereference
bug.
Signed-off by: Hans-Frieder Vogt <hfvogt@gmx.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The driver core clears the driver data to NULL after device_release or on
probe failure. Thus, it is not needed to manually clear the device driver
data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The usage of strict_strtol() is not preferred, because strict_strtol() is
obsolete. Thus, kstrtol() should be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Cc: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the sysfs file creation/removal to the w1 core by using the
.groups field, saving code in the slave driver.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: David Stevenson <david@avoncliff.com>
Cc: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Cc: Michael Arndt <michael@scriptkiller.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This lets w1 slave drivers declare an attribute group, and not have to
create/destroy sysfs files directly. All w1 slave drivers will be fixed
to use this field up in follow-on patches to this one.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we have 2 sysfs files for the w1 slave devices, let the driver core
create / destroy them automatically by setting the default attribute
group for them, saving code and housekeeping logic.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
W1 slave sysfs files are created _after_ userspace is notified that the
device has been added to the system. Fix that race by moving the
creation/remove of the files to the bus notifier that is there for doing
this type of thing.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Power-up timing
The DS2408 is sensitive to the power-on slew rate and can inadvertently
power up with a test mode feature enabled. When this occurs, the P0 port
does not respond to the Channel Access Write command. For most reliable
operation, it is recommended to disable the test mode after every power-on
reset using the Disable Test Mode sequence shown below. The 64-bit ROM
code must be transmitted in the same bit sequence as with the Match ROM
command, i.e., least significant bit first. This precaution is
recommended in parasite power mode (VCC pin connected to GND) as well as
with VCC power.
Disable Test Mode:
RST,PD,96h,<64-bit DS2408 ROM Code>,3Ch,RST,PD
[akpm@linux-foundation.org: don't use kerenldoc token to introduce a non-kerneldoc comment, tweak whitespace]
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch allows the 1-wire bus to autoload the corresponding module
for each slave being attached.
This works similar to bluetooth protocols.
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
Use platform_device_put() instead of platform_device_unregister() if
platform_device_add() fail, and platform_device_del() should be used in
the error handling case after platform_device_add() success.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use platform_device_put() instead of platform_device_unregister() if
platform_device_add() fail, and platform_device_del() should be used in
the error handling case after platform_device_add() success.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use platform_device_put() instead of platform_device_unregister() if
platform_device_add() fail, and platform_device_del() should be used in
the error handling case after platform_device_add() success.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use platform_device_put() instead of platform_device_unregister() if
platform_device_add() fails, and also add the return value check of
platform_device_add_data().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gc7f
-----END PGP SIGNATURE-----
Merge tag 'arizona-extcon-asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into char-misc-next
Mark writes:
ASoC/extcon: arizona: Fix interaction between HPDET and headphone outputs
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
De-activating this reading back will effectively half the time required
for a write to the output register.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Sat, Mar 02, 2013 at 10:45:10AM +0100, Sven Geggus wrote:
> This is the bad commit I found doing git bisect:
> 04f482faf5 is the first bad commit
> commit 04f482faf5
> Author: Patrick McHardy <kaber@trash.net>
> Date: Mon Mar 28 08:39:36 2011 +0000
Good job. I was too lazy to bisect for bad commit;)
Reading the code I found problematic kthread_should_stop call from netlink
connector which causes the oops. After applying a patch, I've been testing
owfs+w1 setup for nearly two days and it seems to work very reliable (no
hangs, no memleaks etc).
More detailed description and possible fix is given below:
Function w1_search can be called from either kthread or netlink callback.
While the former works fine, the latter causes oops due to kthread_should_stop
invocation.
This patch adds a check if w1_search is serving netlink command, skipping
kthread_should_stop invocation if so.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Josh Boyer <jwboyer@gmail.com>
Tested-by: Sven Geggus <lists@fuchsschwanzdomain.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org> # 3.0+
Commit 8a1861d997 ("w1-gpio: Simplify & get rid of defines") removed the
compile guards from the device-tree id table, thereby generating a
warning when building without device-tree support.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8a1861d997 ("w1-gpio: Simplify & get rid of defines") changed
(apparently unknowingly) the driver to a hotpluggable platform-device
driver but did not not update the section markers for probe and remove
(to __devinit/exit, which have since been removed). A later commit fixed
the section mismatch for probe, but left remove marked with __exit.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.8
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This branch contains of devicetree changes for the Freescale i.MX platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process since
every line of the file is touched.
On top of that are a handful of the regular changes; enabling more boards
as DT-based instead of legacy board files (mx25pdk), enabling another
driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other platforms
in the future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=72aL
-----END PGP SIGNATURE-----
Merge tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC i.MX DT changes from Olof Johansson:
"This branch contains of devicetree changes for the Freescale i.MX
platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process
since every line of the file is touched.
On top of that are a handful of the regular changes; enabling more
boards as DT-based instead of legacy board files (mx25pdk), enabling
another driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other
platforms in the future."
* tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: dts: add dtsi for imx6q and imx6dl
ARM: dts: rename imx6q.dtsi to imx6qdl.dtsi
ARM: dts: i.MX6: Add regulator delay support
ARM: dts: Add device tree entry for onewire master on i.MX53
ARM: i.MX53: Add clocks for i.mx53 onewire master.
W1: Add device tree support to MXC onewire master.
ARM: imx: enable imx6q-cpufreq support
ARM: dts: Add apf51 basic support
ARM i.MX6: change mxs usbphy clock usage
ARM: dts: imx6q: Remove silicon version from SDMA firmware
ARM i.MX53: dts: add oftree for MBa53 baseboard
ARM i.MX53: add dts for the TQ tqma53 module
ARM: dts: imx53: pinctrl update
ARM i.MX51 babbage: Add keypad support
ARM: dts: imx: Add imx51 KPP entry
ARM: dts: imx25-karo-tx25: Put status entry in the end
ARM: mx25pdk: Add device tree support
ARM: dts: imx: use nodes label in board dts
ARM: dts: add missing imx dtb targets
ARM: boot: dts: Add an entry for imx27-pdk.dtb
...
Also fixes some whitespace inconsistency in Kconfig and w1_family.h when
DS2408 chip support was added.
Signed-off-by: Mariusz Bialonczyk <manio@skyboo.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei, hyperv, ipack,
extcon, vmci, etc.).
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5
x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK
=i5HH
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg Kroah-Hartman:
"Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei,
hyperv, ipack, extcon, vmci, etc.).
All of these have been in the linux-next tree for a while."
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
w1: w1_therm: Add force-pullup option for "broken" sensors
w1: ds2482: Added 1-Wire pull-up support to the driver
vme: add missing put_device() after device_register() fails
extcon: max8997: Use workqueue to check cable state after completing boot of platform
extcon: max8997: Set default UART/USB path on probe
extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
extcon: max8997: Set default of ADC debounce time during initialization
extcon: max8997: Remove duplicate code related to set H/W line path
extcon: max8997: Move defined constant to header file
extcon: max77693: Make max77693_extcon_cable static
extcon: max8997: Remove unreachable code
extcon: max8997: Make max8997_extcon_cable static
extcon: max77693: Remove unnecessary goto statement to improve readability
extcon: max77693: Convert to devm_input_allocate_device()
extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
CREDITS: update email and address of Harald Hoyer
extcon: arizona: Use MICDET for final microphone identification
extcon: arizona: Always take the first HPDET reading as the final one
extcon: arizona: Clear _trig_sts bits after jack detection
extcon: arizona: Don't HPDET magic when headphones are enabled
...
This fixes the following section mismatch:
WARNING: drivers/w1/masters/w1-gpio.o(.data+0x188): Section mismatch in
reference from the variable w1_gpio_driver to the function
.init.text:w1_gpio_probe()
The variable w1_gpio_driver references
the function __init w1_gpio_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1_therm includes some obsolete code to detect bad_roms, this is no
longer relevant.
The retry code is only used for this bad_rom test, however there is a
CRC check that detects a bad read, but does not trigger a retry. This
patch removes all the bad_rom code and uses the CRC check to trigger
retries.
Signed-off-by: David Stevenson <david@avoncliff.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
At the same time, this fixes two faults. First, mdev, the result of
kzalloc, was never freed. Second, on failure of ioremap, 0 was returned.
This has been replaced by -EBUSY, which was the failure value for the call
to request_mem_region, with which the call to ioremap has been combined.
The warning message on failure of ioremap is dropped, because
devm_request_and_ioremap already gives such messages on failure.
Finally, the initial call to platform_get_resource is moved closer to the
call to devm_request_and_ioremap, which takes care of checking whether its
result is NULL, implying that a test on the result of this call to
platform_get_resource is not needed.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This slipped in through the merging of different trees. Remove
__devexit_p() use in the mxc_w1 driver.
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These devices are not available on other architectures, so
let's limit them to omap.
If the driver subsystem maintainers want to build test
system wide changes without building for each target,
it's easy to carry a test patch that just strips out the
depends entries from Kconfig files.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's no reason to have the OF defines; it complicates the driver.
There's also no need for the funky platform_driver_probe.
Add a few warnings in case there's a failure; helps us find out
what went wrong.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are dealing with mxc_w1 registers.
While at it use dev_err() instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using module_platform_driver() makes the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the new i.mx clock framework the mxc_w1 clock is registered as:
clk_register_clkdev(clk[owire_gate], NULL, "mxc_w1.0");
So we do not need to pass "owire" string and can use NULL instead.
While at it, also fix the clock error handling code.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
-----
Changes since v2:
- Add Ack's
Changes since v1:
- Fix clock error handling
drivers/w1/masters/mxc_w1.c | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_i2c_driver() macro to make the code smaller
and a bit simpler.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Paul Walmsley <paul@pwsan.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "big" char/misc driver tree update for the 3.7-rc1 merge
window.
Nothing major, just a number of driver updates and fixes, all of which
have been in the linux-next releases for a while now either in my tree,
or in Andrew's (the lis3l driver changes came from his tree last week).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp3pcACgkQMUfUDdst+ymLswCcDYG9RkRcEdYwT5bOm1zM4IVl
WM0AoLKfC86g6xe4MdS7zROJn7ep/9qu
=zAHk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver merge from Greg Kroah-Hartman:
"Here is the "big" char/misc driver tree update for the 3.7-rc1 merge
window.
Nothing major, just a number of driver updates and fixes, all of which
have been in the linux-next releases for a while now either in my
tree, or in Andrew's (the lis3l driver changes came from his tree last
week).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (52 commits)
drivers/misc/lis3lv02d/lis3lv02d_i2c.c: add lis3lv02d device tree init
drivers/misc/lis3lv02d/lis3lv02d_spi.c: add lis3lv02d device tree init
drivers/misc/lis3lv02d: remove lis3lv02d driver DT init
drivers/misc/lis3lv02d/lis3lv02d_spi.c: add DT matching table passthru code
drivers/misc/lis3lv02d: add generic DT matching code
lis3lv02d: fix some comments specific to lis331dlh driver
MISC: hpilo, remove pci_disable_device
pcmcia: synclink_cs: fix potential tty NULL dereference
drivers/char/mmtimer.c: Remove useless kfree
drivers/char: removes unnecessary semicolon
char/misc: remove CONFIG_EXPERIMENTAL dependencies
mei: don't print buffer as a string
mei: struct mei_message_data doesn't have to be packed
mei: add error messages for open count errors
misc: use module_spi_driver
tifm: use module_pci_driver
misc/at25, dt: Improve at25 SPI eeprom device tree bindings.
mei: add lynx point pci device ids
mei: fix max number of open handles
mei: rename struct pci_dev *mei_device to mei_pdev
...
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
This patch adds support for maxim ds1825 based 1-wire temperature sensors.
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the process of porting boards to devicetree implemenation, we should
keep information about external circuitry where they belong - the
individual drivers.
This patch adds a way to specify a GPIO to drive the (optional) external
pull-up logic, rather than using a function pointer for that.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add DT bindings to the w1-gpio driver, along with some
documentation on how to use them.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let the driver compile everywhere while
also removing unnecessary headers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this lets us remove a bit of boilerplate code.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
we have the helpful resource_size() macro to
calculate the size of the memory resource for
us, let's use it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big driver core pull request for 3.6-rc1.
Unlike 3.5, this kernel should be a lot tamer, with the printk changes now
settled down. All we have here is some extcon driver updates, w1 driver
updates, a few printk cleanups that weren't needed for 3.5, but are good to
have now, and some other minor fixes/changes in the driver core.
All of these have been in the linux-next releases for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlARgIUACgkQMUfUDdst+ynDHgCfRNwIB9L+zZvjcKE5e1BhDbUl
wVUAn398DFgbJ1+PjGkd1EMR2uVTh7Ou
=MIFu
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core changes from Greg Kroah-Hartman:
"Here's the big driver core pull request for 3.6-rc1.
Unlike 3.5, this kernel should be a lot tamer, with the printk changes
now settled down. All we have here is some extcon driver updates, w1
driver updates, a few printk cleanups that weren't needed for 3.5, but
are good to have now, and some other minor fixes/changes in the driver
core.
All of these have been in the linux-next releases for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (38 commits)
printk: Export struct log size and member offsets through vmcoreinfo
Drivers: hv: Change the hex constant to a decimal constant
driver core: don't trigger uevent after failure
extcon: MAX77693: Add extcon-max77693 driver to support Maxim MAX77693 MUIC device
sysfs: fail dentry revalidation after namespace change fix
sysfs: fail dentry revalidation after namespace change
extcon: spelling of detach in function doc
extcon: arizona: Stop microphone detection if we give up on it
extcon: arizona: Update cable reporting calls and split headset
PM / Runtime: Do not increment device usage counts before probing
kmsg - do not flush partial lines when the console is busy
kmsg - export "continuation record" flag to /dev/kmsg
kmsg - avoid warning for CONFIG_PRINTK=n compilations
kmsg - properly print over-long continuation lines
driver-core: Use kobj_to_dev instead of re-implementing it
driver-core: Move kobj_to_dev from genhd.h to device.h
driver core: Move deferred devices to the end of dpm_list before probing
driver core: move uevent call to driver_register
driver core: fix shutdown races with probe/remove(v3)
Extcon: Arizona: Add driver for Wolfson Arizona class devices
...
Convert the OMAP HDQ driver to use runtime PM. Compile- and boot-tested,
but not tested in actual use.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Tested-by: NeilBrown <neilb@suse.de>
HDQ/1-wire registers are 32 bits long, even if the register contents
fit into 8 bits, so accesses must be 32-bit aligned. Evidently the
OMAP2/3 interconnects allowed the driver to get away with 8 bit accesses,
but the OMAP4 puts a stop to that:
[ 1.488800] Driver for 1-wire Dallas network protocol.
[ 1.495025] Bad mode in data abort handler detected
[ 1.500122] Internal error: Oops - bad mode: 0 [#1] SMP
[ 1.505615] Modules linked in:
[ 1.508819] CPU: 0 Not tainted (3.3.0-rc1-00008-g45030e9 #992)
[ 1.515289] PC is at 0xffff0018
[ 1.518615] LR is at omap_hdq_probe+0xd4/0x2cc
The OMAP4430 ES2 Rev X TRM does warn about this restriction in section
23.2.6.2 "HDQ/1-Wire Registers".
Fixes the crash on OMAP4430 ES2 Pandaboard. Tested also on OMAP34xx and
OMAP2420; it seems to work fine on those chips, although due to the lack
of boards with HDQ/1-wire devices here, a more indepth test was not
possible.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Allow the OMAP HDQ1W driver to be built for all OMAP2+ SoCs by
adjusting KConfig dependencies. The previous dependency required
either SOC_OMAP2430 or ARCH_OMAP3 to be set, but the HDQ IP block is
present on OMAP2420 and OMAP44xx SoCs. The driver was still
selectable on multi-OMAP kernel configurations, however; so the
previous prohibition was rather pointless.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
The 'mutex' in struct w1_master is use for two very different
purposes.
Firstly it protects various data structures such as the list of all
slaves.
Secondly it protects the w1 buss against concurrent accesses.
This can lead to deadlocks when the ->probe code called while adding a
slave needs to talk on the bus, as is the case for power_supply
devices.
ds2780 and ds2781 drivers contain a work around to track which
process hold the lock simply to avoid this deadlock. bq27000 doesn't
have that work around and so deadlocks.
There are other possible deadlocks involving sysfs.
When removing a device the sysfs s_active lock is held, so the lock
that protects the slave list must take precedence over s_active.
However when access power_supply attributes via sysfs, the s_active
lock must take precedence over the lock that protects accesses to
the bus.
So to avoid deadlocks between w1 slaves and sysfs, these must be
two separate locks. Making them separate means that the work around
in ds2780 and ds2781 can be removed.
So this patch:
- adds a new mutex: "bus_mutex" which serialises access to the bus.
- takes in mutex in w1_search and ds1wm_search while they access
the bus for searching. The mutex is dropped before calling the
callback which adds the slave.
- changes all slaves to use bus_mutex instead of mutex to
protect access to the bus
- removes w1_ds2790_io_nolock and w1_ds2781_io_nolock, and the
related code from drivers/power/ds278[01]_battery.c which
calls them.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no gain in having a loop - there is no risk of missing the
interrupt with wait_event_timeout.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- some debug messages missed spaces
- sometimes no error was returned when it should have been
- sometimes a message is printed when there is no error, rather
than when there is one.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 59d4467be4.
Turns out it was the wrong version, will apply the correct version after
this.
Reported-by: NeilBrown <neilb@suse.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were some return statements around in the w1_uevent, used goto
to cleanup those return statements with the help of err variable,
and also removed a semi colon at the end of the w1_uevent's closing
brace.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1 devices need a mutex to serial IO. Most use master->mutex.
However that is used for other purposes and they can conflict.
In particular master->mutex is held while w1_attach_slave_device is
called.
For bq27000, this registers a 'powersupply' device which tries to read the
current status. The attempt to read will cause a deadlock on
master->mutex.
So create a new per-slave mutex and use that for serializing IO for
bq27000.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
There are three Kconfig entries with "--- help ---" attributes, and over
2000 Kconfig entries with "---help---" attributes. Apparently the three
attributes with embedded spaces are valid. Still, I see little reason
for using this obscure variant. And replacing those three attributes
with the common variant makes grepping Kconfig files for help texts a
bit easier too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
NULL not 0 should be used with pointers. Just remove the offending
lines since they will default to NULL anyway.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f19420c1ac.
It contained lots of errors and warnings and shouldn't have ever been
applied, that was my fault, sorry.
Cc: Markus Franke <markus.franke@s2002.tu-chemnitz.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>,
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should unlock here before returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch offers the possibility to disables irqs during w1_write_bit()
and w1_reset_bus() operations as timing requirements are very strict for
the 1-wire bus protocol. Per default interrupts are enabled but can be
disabled via the module parameter "w1_disable_irqs".
Extend 1-wire reset pulse length from 480us to 500us as 480us is the
minimum requirement for the 1-wire reset/presence pulse.
Signed-off-by: Markus Franke <franm@hrz.tu-chemnitz.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a 1-wire slave device driver for the DS28E04-100.
Signed-off-by: Markus Franke <franm@hrz.tu-chemnitz.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge with latest Linus' tree, as I have incoming patches
that fix code that is newer than current HEAD of for-next.
Conflicts:
drivers/net/ethernet/realtek/r8169.c
If multiple threads try, they trip over each other badly.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function is never used so remove it to avoid bit-rot.
It can trivially be re-added if there is ever a need.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As recent change means that we now dereference 'dev' before testing
for NULL.
That means either the change was wrong, or the test isn't needed.
As this function is only called from one driver (bq27x000_battery) and
it always passed a non-NULL dev, it seems good to assume that the
test isn't needed.
So remove it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1_bq27000 adds a bq27000-battery platform device but does not provide
platform data for it. This causes the bq27x00 driver to dereference a NULL
pointer.
So provide the appropriate platform data. This requires modifying
w1_bq27000_read so that it find the w1 device as the parent of the bq device.
Also there is no point exporting w1_bq27000_read as nothing else uses it
or could use it. So make it static.
Finally, as there is no way to track how many batteries have been found, and
we will probably only find one, use an id number of '-1' to assert that this
is a unique instance.
Signed-off-by: NeilBrown <neilb@suse.de>
Tested-by: Thomas Weber <weber@corscience.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Direct inclusion of the asm header has long been deprecated by the
introduction of gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This enables a much more efficient way of device searching. It uses the
1-wire read-rom operation which allows the direct reading of the slave
address. BUT this works only with exactly one slave on the bus.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
index c374978..9761950 100644
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts the remaining USB drivers in the kernel to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Till Harbaum <till@harbaum.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
w1_therm devices can either be bus powered or externally powered.
When device is bus powered during temperature conversion the bus
have to be left high to provide necessary power. Some masters also allow
strong power-up to be enabled in this case.
Naturally, no communication over bus can occur during that time.
However, if device has external power then there is no such restriction,
and host can talk to other devices during temperature conversion.
There is command which allows us to check how device is powered,
this patch uses it to release the bus on externally w1_therm powered devices
during temperature conversion.
Also, this changes uninterruptible sleeps there into interruptible ones to
avoid long uninterruptible sleep if w1 subsystem happens to grab bus for
scan during w1_therm_read().
Signed-off-by: Maciej Szmigiero <mhej@o2.pl>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Interrupting w1_delay() in w1_read_bit() results in missing the low level
on the w1 line and receiving "1" instead of "0".
Add local_irq_save()/local_irq_restore() around the critical section
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds a nolock function to the w1 interface to avoid locking the
mutex if needed.
Signed-off-by: Clifton Barnes <cabarnes@indesign-llc.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Straightforward. As an aside, the ida_init calls are not needed as far as
I can see needed. (DEFINE_IDA does the same already).
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Clifton Barnes <cabarnes@indesign-llc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It doesn't need the full module.h but it was getting moduleparam.h
from the fact that module.h was everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Give these files export.h so that they can reliably get the EXPORT_SYMBOL
and THIS_MODULE macros in the future, once module.h isn't implicitly
everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The for loop was looking for i <= 0 instead of i >= 0 so this function
never did anything. Also we started with i = NB_SYSFS_BIN_FILES instead
of "NB_SYSFS_BIN_FILES - 1" which is an off by one bug.
Reported-by: Bojan Prtvar <prtvar.b@gmail.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jean-Franois Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a regression in 3.0 reported by Paul Parsons regarding the
removal of the msleep(1) in the ds1wm_reset() function:
: The linux-3.0-rc4 DS1WM 1-wire driver is logging "bus error, retrying"
: error messages on an HP iPAQ hx4700 PDA (XScale-PXA270):
:
: <snip>
: Driver for 1-wire Dallas network protocol.
: DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko
: 1-Wire driver for the DS2760 battery monitor chip - (c) 2004-2005, Szabolcs Gyurko
: ds1wm ds1wm: pass: 1 bus error, retrying
: ds1wm ds1wm: pass: 2 bus error, retrying
: ds1wm ds1wm: pass: 3 bus error, retrying
: ds1wm ds1wm: pass: 4 bus error, retrying
: ds1wm ds1wm: pass: 5 bus error, retrying
: ...
:
: The visible result is that the battery charging LED is erratic; sometimes
: it works, mostly it doesn't.
:
: The linux-2.6.39 DS1WM 1-wire driver worked OK. I haven't tried 3.0-rc1,
: 3.0-rc2, or 3.0-rc3.
This sleep should not be required on normal circuitry provided the
pull-ups on the bus are correctly adapted to the slaves. Unfortunately,
this is not always the case. The sleep is restored but as a parameter to
the probe function in the pdata.
[akpm@linux-foundation.org: coding-style fixes]
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Maxim/Dallas DS2780 Stand-Alone Fuel Gauge IC.
It was suggested to combine this functionality with the current ds2782
driver. Unfortunately, I'm unable to commit the time to refactoring this
driver to that extent and I don't have a platform with the ds2782 part to
validate that there are no regression issues by adding this functionality.
[akpm@linux-foundation.org: use min_t()]
Signed-off-by: Clifton Barnes <cabarnes@indesign-llc.com>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reorganize so the netlink connector one wire search command will update
the kernel list of detected slave devices. Otherwise, a newly detected
device is unusable because unless it's in the kernel list of known devices
any commands will result in ENODEV status.
Signed-off-by: David Fries <David@Fries.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds multi-slave support of the w1 bus for the ds1wm Synthesizable
1-Wire Bus Master. Also many fixes and tweaks based on the rev3 of the
datasheet http://datasheets.maxim-ic.com/en/ds/DS1WM.pdf
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Cc: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This DS2408 w1 slave driver is not complete for all the features of the
chip, but its sufficient if you use it as a simple IO expander.
[randy.dunlap@oracle.com: fix w1_ds2408.c printk formats]
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Cc: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The first patch adds generic functionnality to w1_io for Resume Command
[A5h] lots of slaves support. I found it useful for multi-commands/reset
workflows with the same slave on a multi-slave bus.
This DS2408 w1 slave driver is not complete for all the features of the
chip, but its sufficient if you use it as a simple IO expander. Enjoy!
The ds1wm had Kconfig dependencies towards ARM && HAVE_CLK. I took them
out since I was using the ds1wm on an x86_64 platform (ds1wm in a FPGA
through pcie) and found them irrelevant.
The clock freq/divisors at the top of ds1wm.c did not have the MSB set to
1. This bit is CLK_EN which turns the whole prescaler and dividers on.
The driver never mentionned this bit either, so I just included this bit
right in the table entries. I also took the liberty to add a couple of
entries to the table. The spec doesn't explicitely mentions these
possibilities but the description and examination of the core shows the
prescalers & dividers can be used for more than the table explicitely
shows. The table I enlarged still doesn't cover all possibilities, but
it's a good start.
I also made a few tweaks to a couple of the read and write algorithms
which made sense while I had my head very deep in the ds1wm documentation.
We stressed it a lot with 10+ slaves on the bus, many ds2408, ds2431 and
ds2433 at the same time doing extensive interaction. It proved quite
stable in our production environment.
This patch:
Add generic functionnality to w1_io for Resume Command [A5h] lots of
slaves support.
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Cc: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the addition of the platform device mfd_cell pointer, we can now
cleanly pass the sub device drivers platform data pointers through the
regular device platform_data one, and get rid of mfd_get_data().
Cc: Matt Reimer <mreimer@vpop.net>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
mfd_get_cell returns a const, so change the ds1wm client to store
a const mfd cell. This silences type mismatch warnings.
Since we're guaranteed to have the mfd_cell, we can also simplify
the code a bit to get rid of a temporary variable and NULL check.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use mfd_data for passing information from mfd drivers to mfd
clients. The mfd_cell's driver_data field is being phased out.
Clients that were using driver_data now access .mfd_data
via mfd_get_data(). This changes ds1wm only; mfd drivers with
other cells are not modified, with the exception of led_cell.
The led_cell.driver_data line is dropped from htc-pasic3.c in this
patch as well. It's not used in mainline (there's no leds-pasic3
platform driver), so it should be safe to take care of that here.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
No need to explicitly set the cell's platform_data/data_size.
Modify clients to use mfd_get_cell helper function instead of
accessing platform_data directly.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This code makes two calls to clk_get, then test both return values and
fails if either failed.
The problem is that in the first inner if, where the first call to
clk_get has failed, it don't know if the second call has failed as well.
So it don't know whether clk_get should be called on the result of the
second call. Of course, it would be possible to test that value again.
A simpler solution is just to test the result of calling clk_get
directly after each call.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
position p1,p2;
expression e;
statement S;
@@
e = clk_get@p1(...)
...
if@p2 (IS_ERR(e)) S
@@
expression e;
statement S;
identifier l;
position r.p1, p2 != r.p2;
@@
*e = clk_get@p1(...)
... when != clk_put(e)
*if@p2 (...)
{
... when != clk_put(e)
* return ...;
}// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We want to have just CONFIG_ARCH_OMAP2, 3 and 4. The rest
are nowadays just subcategories of these.
Search and replace the following:
ARCH_OMAP2420 SOC_OMAP2420
ARCH_OMAP2430 SOC_OMAP2430
ARCH_OMAP3430 SOC_OMAP3430
No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
The search/pullup/add/remove device attributes were 0666 which would allow
arbitrary users to affect the 1 wire bus. Change to 0664 to prevent that.
I found this patch in the Android tree, apparently this has never been
sent upstream so doing it now.
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes the following error:
drivers/w1/masters/omap_hdq.c: In function 'hdq_wait_for_flag':
drivers/w1/masters/omap_hdq.c:137: error: implicit declaration of function 'schedule_timeout_uninterruptible'
drivers/w1/masters/omap_hdq.c: In function 'hdq_write_byte':
drivers/w1/masters/omap_hdq.c:177: error: 'TASK_UNINTERRUPTIBLE' undeclared (first use in this function)
drivers/w1/masters/omap_hdq.c:177: error: (Each undeclared identifier is reported only once
drivers/w1/masters/omap_hdq.c:177: error: for each function it appears in.)
drivers/w1/masters/omap_hdq.c:177: error: implicit declaration of function 'schedule_timeout'
drivers/w1/masters/omap_hdq.c: In function 'hdq_isr':
drivers/w1/masters/omap_hdq.c:221: error: 'TASK_NORMAL' undeclared (first use in this function)
drivers/w1/masters/omap_hdq.c: In function 'omap_hdq_break':
drivers/w1/masters/omap_hdq.c:316: error: 'TASK_UNINTERRUPTIBLE' undeclared (first use in this function)
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix regression caused by commit 507e2fbaaa
("w1: w1 temp calculation overflow fix") whereby negative temperatures for
the DS18B20 are not converted properly.
When the temperature exceeds 32767 milli-degrees the temperature overflows
to -32768 millidegrees. These are both well within the -55 - +125 degree
range for the sensor.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=12646
Signed-of-by: Ian Dall <ian@beware.dropbear.id.au>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Tested-by: Karsten Elfenbein <kelfe@gmx.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
A pointer to omap_hdq_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Stanley.Miao <stanley.miao@windriver.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trivial patch which adds the __init/__exit macros to the module_init/
module_exit functions of
drivers/w1/w1.c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no point in implementing a detect callback for the DS2482, as
this device can't be detected. It was there solely to handle "force"
module parameters to instantiate devices, but now we have a better sysfs
interface that can do the same.
So we can get rid of the ugly module parameters and the detect callback.
This shrinks the binary module size by 21%.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was found using a semantic patch, more info can be found at:
http://www.emn.fr/x-info/coccinelle/
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The connector documentation states that the argument to the callback
function is always a pointer to a struct cn_msg, but rather than encode it
in the API itself, it uses a void pointer everywhere. This doesn't make
much sense to encode the pointer in documentation as it prevents proper C
type checking from occurring and can easily allow people to use the wrong
pointer type. So convert the argument type to an explicit struct cn_msg
pointer.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.infradead.org/battery-2.6:
da9030_battery: Fix race between event handler and monitor
Add MAX17040 Fuel Gauge driver
w1: ds2760_battery: add support for sleep mode feature
w1: ds2760: add support for EEPROM read and write
ds2760_battery: cleanups in ds2760_battery_probe()
On embedded devices, sleep mode conditions can be tricky to handle,
Especially when processors tend to pull-down the w1 bus during sleep. Bus
slaves (such as the ds2760) may interpret this as a reason for power-down
conditions and entirely switch off the device.
This patch adds a callback function pointer to let users switch on and off
the external pull-up resistor. This lets the outside world know whether
the processor is currently actively driving the bus or not.
When this callback is not provided, the code behaviour won't change.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Ville Syrjala <syrjala@sci.fi>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds support for ds2760's sleep mode feature. With this feature
enabled, the chip enters a deep sleep mode and disconnects from the
battery when the w1 line is held down for more than 2 seconds.
This new behaviour can be switched on and off using a new module
parameter.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Acked-by: Matt Reimer <mreimer@vpop.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
In order to modify the DS2762's status registers and to add support for
sleep mode, there is need for functions to write the internal EEPROM.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Matt Reimer <mreimer@vpop.net>
Acked-by: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This driver requests a clock that usually is supplied by the MFD in which
the DS1WM is contained. Currently, it is impossible for a MFD to register
their clocks with the generic clock API due to different implementations
across architectures.
For now, this patch removes the clock handling from DS1WM altogether,
trusting that the MFD enable/disable functions will switch the clock if
needed. The clock rate is obtained from a new parameter in driver_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch converts the DS1WM driver into an MFD cell. It also
calculates the bus_shift parameter from the memory resource size.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This fixes a number of coding style issues I stubled over.
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The context makes it clear already that these are clocks, so there's
no need for such a suffix. This patch only changes the clocks actually
used in the tree. The remaining clocks are renamed in the subsequent
architecture specific patches.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
W1 master implementations are expected to return 0 or 1 from their
read_bit() function. However, not all platforms do return these values
from gpio_get_value() - namely PXAs won't. Hence the w1 gpio-master needs
to break the result down to 0 or 1 itself.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The w1_ds2433 driver does not read from the hardware if the CRC was valid
on the last read. The validcrc flag should be cleared after a write so
that the new value can be read.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=12646
When the temperature exceeds 32767 milli-degrees the temperature overflows
to -32768 millidegrees. These are bothe well within the -55 - +125 degree
range for the sensor.
Fix overflow in left-shift of a u8.
Signed-off-by: Ian Dall <ian@beware.dropbear.id.au>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Send completion status of the commands to the userspace. Message and
protocol are described in the documentation.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Command which allows to reset the bus.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This small patchset extendes existing commands with reset, master IO and
status messages. Reset is used to reset the bus for given master device,
master IO command allows to initiate IO against bus itself not selecting
slave device first, which can be used to probe the device for example.
And status messages carry command completion status back to the userspace
(namely very useful to get -ENODEV from when requested device was not
found).
Great thanks to Paul Alfille of OWFS for testing and commands suggestions.
This patch:
Allow starting of IO not against already found slave devices, but against
the bus itself, which can be used for example to probe devices.
[akpm@linux-foundation.org: reindent switch statements]
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initiates search (or alarm search) and returns all found devices to
userspace. Found devices are not added into the system (i.e. they are
not attached to family devices or bus masters), it will be done via (if
was not done yet) usual timed searching.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Writes and returns sampled data back to userspace.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series introduces and extends several userspace commands
used with netlink protocol.
Touch block command allows to write data and return sampled data to
the userspace.
Extended search and alarm seach commands to return list of slave
devices found during given search.
List masters command allows to send all registered master IDs to the
userspace.
Great thanks to Paul Alfille (owfs) who
tested this implementation and wrote w1-to-network daemon
http://sourceforge.net/projects/w1repeater/ and
Frederik Deweerdt and Randy Dunlap for review.
This patch:
Returns list of registered bus master devices.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Cc: Frederik Deweerdt <frederik.deweerdt@xprog.eu>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the 1-wire master interface for i.MX27 and
i.MX31.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During test of the w1-gpio driver i found that in "w1.c:679
w1_slave_found()" the device id is converted to little-endian with
"cpu_to_le64()", but its not converted back to cpu format in "w1_io.c:293
w1_reset_select_slave()".
Based on a patch created by Andreas Hummel.
[akpm@linux-foundation.org: remove unneeded cast]
Reported-by: Andreas Hummel <andi_hummel@gmx.de>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Uses clk_...() a lot
Acked-by: rmk+kernel@arm.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OMAP LDP boot crash. This is because w1 subsystem changed the search
interface, so update omap_hdq's search interface to follow the change.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The HDQ/1-Wire module of TI OMAP2430/3430 platforms implement the hardware
protocol of the master functions of the Benchmark HDQ and the Dallas
Semiconductor 1-Wire protocols. These protocols use a single wire for
communication between the master (HDQ/1-Wire controller) and the slave
(HDQ/1-Wire external compliant device).
This patch provides the HDQ driver to suppport TI OMAP2430/3430 platforms.
Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export the w1_read_8 function for use of drivers. The OMAP HDQ
driver(drivers/w1/masters/omap_hdq.c) uses this function.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tejun's commit 7b595756ec made sysfs
attribute->owner unnecessary. But the field was left in the structure to
ease the merge. It's been over a year since that change and it is now
time to start killing attribute->owner along with its users - one arch at
a time!
This patch is attempt #1 to get rid of attribute->owner only for
CONFIG_X86_64 or CONFIG_X86_32 . We will deal with other arches later on
as and when possible - avr32 will be the next since that is something I
can test. Compile (make allyesconfig / make allmodconfig / custom config)
and boot tested.
akpm: the idea is that we put the declaration of sttribute.owner inside
`#ifndef CONFIG_X86'. But that proved to be too ambitious for now because
new usages kept on turning up in subsystem trees.
[akpm: remove the ifdef for now]
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[akpm@linux-foundation.org: minor fixlets and cleanups]
Signed-off-by: Bernhard Weirich <bernhard.weirich@riedel.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Optimize the ds_set_pullup function. For a strong pullup to be sent the
ds2490 has to have both the strong pullup mode enabled, and the specific
write operation has to have the SPU bit enabled. Previously the write
always had the SPU bit enabled and both the duration and model was set
when a strong pullup was requested. Now the strong pullup mode is enabled
at initialization time, the delay is updated only when the value changes,
and the write SPU bit is set only when a strong pullup is required. This
removes two or three bus transactions per strong pullup request.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop the extra ds_wait_status() in ds_write_block().
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This replaces some magic numbers with marcos and corrects one marco.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reset the device in init as it can be in a bad state. This is necessary
because a block write will wait for data to be placed in the output buffer
and block any later commands which will keep accumulating and the device
will not be idle. Another case is removing the ds2490 module while a bus
search is in progress, somehow a few commands get through, but the input
transfers fail leaving data in the input buffer. This will cause the next
read to fail see the note in ds_recv_data.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ds_reset no longer calls ds_wait_status, the result wasn't used and it
would only delay the following data operations.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- add result register #defines
- rename ds_dump_status to ds_print_msg
- rename ds_recv_status to ds_dump_status
- ds_dump_status prints the requested status and no longer reads the
status, this is because the second status read can return different
data for example the result register
- the result register will be printed, though limited to detecting a
new device, detecting other values such as a short would require
additional reporting methods
- ST_EPOF was moved to ds_wait_status to clear the error condition
sooner
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplify and fix ds_touch_bit. If a device is attached in the middle of a
bus search the status register will return more than the default 16 bytes.
The additional bytes indicate that it has detected a new device. The way
ds_wait_status is coded, if it doesn't read 16 status bytes it returns an
error value. ds_touch_bit then will detect that error and return an
error. In that case it doesn't read the input buffer and returns
uninitialized data. It doesn't stop there. The next transaction will not
expect the extra byte in the input buffer and the short read will cause an
error and clear out both the old byte and new data in the input buffer.
Just ignore the value of ds_wait_status. It is still required to wait
until ds2490 is again idle and there is data to read when ds_recv_data is
called. This also removes the while loop. None of the other commands
wait and verify that the issued command is in the status register.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't export read and write bit operations, they didn't work, they weren't
used, and they can't be made to work. The one wire low level bit
operations expect to set high or low levels, the ds2490 hardware only
supports complete read or write time slots, better to just comment them
out.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ds_write_bit doesn't read the input buffer, so add COMM_ICP and a comment
that it will no longer generate a read back data byte. If there is an
extra data byte later on then it will cause an error and discard what data
was there. Corrected operator ordering for ds_send_control.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add strong pullup support for ds2490 driver, also drop mdelay(750), which
busy waits, usage in favour of msleep for long delays. Now with msleep
only being called when the strong pullup is active, one wire bus
operations are only taking minimal system overhead.
The new set_pullup will only enable the strong pullup when requested,
which is expected to be the only write operation that will benefit from a
strong pullup.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Corrected print message, it was writing not reading, this also prints the
endpoint used for the write instead of hardcoding it. Failed to write
1-wire data to ep0x%x: err=%d.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Like the previous w1_io.c reset coments and msleep patch, I don't have the
hardware to verify the change, but I think it is safe. It also helps to
see a comment like this in the code. "We'll wait a bit longer just to be
sure." If they are going to calculate delaying 324.9us, but actually delay
500us, why not just give up the CPU and sleep? This is designed for a
battery powered ARM system, avoiding busywaiting has to be good for
battery life.
I sent a request for testers March 7, 2008 to the Linux kernel mailing
list and two developers who have patches for ds1wm.c, but I didn't get
any respons.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
w1_reset_bus, added some comments about the timing and switched to msleep
for the later delay. I don't have the hardware to test the sleep after
reset change. The one wire doesn't have a timing requirement between
commands so it is fine. I do have the USB hardware and it would be in big
trouble with 10ms interrupt transfers to find that the reset completed.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Follow the example of other devices (like the joystick device). Pick the
first available id for each detected device. Currently for USB devices,
suspending and resuming would cause the number to increment.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sl->master->mutex and dev->mutex refer to the same mutex variable, but be
consistent and use the same set of pointers for the lock and unlock calls.
It is less confusing (and one less pointer dereference this way).
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removed the w1_family structure member variable need_exit. It was only
being set and never used. Even if it were to be used it is a polling type
operation.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed data reading bug by replacing binary attribute with device one.
Switching the sysfs read from bin_attribute to device_attribute. The data
is far under PAGE_SIZE so the binary interface isn't required. As the
device_attribute interface will make one call to w1_therm_read per file
open and buffer, the result is, the following problems go away.
buffer overflow:
Execute a short read on w1_slave and w1_therm_read_bin would still
return the full string size worth of data clobbering the user space
buffer when it returned. Switching to device_attribute avoids the
buffer overflow problems. With the snprintf formatted output dealing
with short reads without doing a conversion per read would have
been difficult.
bad behavior:
`cat w1_slave` would cause two temperature conversions to take place.
Previously the code assumed W1_SLAVE_DATA_SIZE would be returned with
each read. It would not return 0 unless the offset was less
than W1_SLAVE_DATA_SIZE. The result was the first read did a
temperature conversion, filled the buffer and returned, the
offset in the second read would be less than
W1_SLAVE_DATA_SIZE and also fill the buffer and return, the
third read would finnally have a big enough offset to return 0
and cause cat to stop. Now w1_therm_read will be called at
most once per open.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug reading the id sysfs file. If less than the full 8 bytes were
read, the next read would start at the first byte instead of continuing.
It needed the offset added to memcpy, or the better solution was to
replace it with the device attribute instead of bin attribute.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added a new module parameter search_count which allows overriding the
default search count. -1 continual, 0 disabled, N that many times.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplified the logic in w1_slave_found by using the new
w1_attach_slave_device function to find a slave and mark it as active or
add the device if the crc checks.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sysfs entries were added to manually add and remove slave devices. This
is useful if the automatic bus searching is disabled, and the device ids
are already known.
[akpm@linux-foundation.org: fix printk types]
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added strong pullup to thermal sensor driver and general documentation on
the sensor.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a strong pullup option to the w1 system. This supplies extra power
for parasite powered devices. There is a w1_master_pullup sysfs entry and
enable_pullup module parameter to enable or disable the strong pullup.
The one wire bus requires at a minimum one wire and ground. The common
wire is used for sending and receiving data as well as supplying power to
devices that are parasite powered of which temperature sensors can be one
example. The bus must be idle and left high while a temperature
conversion is in progress, in addition the normal pullup resister on
larger networks or even higher temperatures might not supply enough power.
The pullup resister can't provide too much pullup current, because
devices need to pull the bus down to write a value. This enables the
strong pullup for supported hardware, which can supply more current when
requested. Unsupported hardware will just delay with the bus high.
The hardware USB 2490 one wire bus master has a bit on some commands which
will enable the strong pullup as soon as the command finishes executing.
To use strong pullup, call the new w1_next_pullup function to register the
duration. The next write command will call set_pullup before sending the
data, and reset the duration to zero once it returns.
Switched from simple_strtol to strict_strtol.
Signed-off-by: David Fries <david@fries.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The w1_process thread's sleeping and termination has been modified.
msleep_interruptible was replaced by schedule_timeout and schedule to
allow for kthread_stop and wake_up_process to interrupt the sleep and the
unbounded sleeping when a bus search is disabled. The W1_MASTER_NEED_EXIT
and flags variable were removed as they were redundant with
kthread_should_stop and kthread_stop. If w1_process is sleeping,
requesting a search will immediately wake it up rather than waiting for
the end of msleep_interruptible previously.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the creation of the w1_process thread to after the device has been
initialized. This way w1_process doesn't have to check to see if it has
been initialized and the bus search can proceed without sleeping. That
also eliminates two checks in the w1_process loop. The sleep now happens
at the end of the loop not the beginning.
Also added a comment for why the atomic_set was 2.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Early abort if the master driver or the hardware goes away in the middle
of a bus search operation. The alternative is to spam the print buffer up
to 64*64 times with read errors in the case of USB.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
w1_control_thread was removed which would wake up every second and process
newly registered family codes and complete some final cleanup for a
removed master. Those routines were moved to the threads that were
previously requesting those operations. A new function
w1_reconnect_slaves takes care of reconnecting existing slave devices when
a new family code is registered or removed. The removal case was missing
and would cause a deadlock waiting for the family code reference count to
decrease, which will now happen. A problem with registering a family code
was fixed. A slave device would be unattached if it wasn't yet claimed,
then attached at the end of the list, two unclaimed slaves would cause an
infinite loop.
The struct w1_bus_master.search now takes a pointer to the struct
w1_master device to avoid searching for it, which would have caused a
lock ordering deadlock with the removal of w1_control_thread.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new-style ds2482 driver implements the optional detect() callback
to cover the use cases of the legacy driver. I'm curious if anyone
really needs this though, so it might be removed in the feature.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch replaces dev_dbg() by dev_err(), so the user could actually see the
error, instead of wondering why w1 doesn't work. The root cause of the bus
reset error isn't yet debugged though, but this sometimes happens on iPaq
H5555.
And while I'm at it, some cosmetic cleanups also made (few lines were using
spaces instead of tabs).
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the error condition clk_get() returns ERR_PTR(..), so checking for NULL
doesn't work. ds1wm module causes a kernel oops when ds1wm clock isn't
registered.
This patch converts NULL check to IS_ERR(), plus uses PTR_ERR()
for the return code.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DS1WM driver incorrectly infers the IAS bit (1-wire interrupt active
high) from IRQ settings. There are devices that have IAS=0 but still need
the IRQ to trigger on a rising edge. With this patch, machines with DS1WM
that need IAS=1 have to set .active_high=1 in the ds1wm_platform_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Acked-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a GPIO 1-wire bus master driver. The driver used the GPIO API to
control the wire and the GPIO pin can be specified using platform data
similar to i2c-gpio. The driver was tested with AT91SAM9260 + DS2401.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Standardize the temperature units to millidegrees C for the two sensor
conversion routines. Previously the routines were,
w1_DS18B20_convert_temp degrees C
w1_DS18S20_convert_temp millidegrees C
Unfortunately this will break any program using the ds18b20 value as it
will now be 1000 times bigger. Fortunately there can't be that many users
out there, or some of these bugs will have been fixed by now, such as the
negative C error (see previous patch) that makes me think the ds18b20 is
the better choice to change because of the current bugs.
Signed-off-by: David Fries <david@fries.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remvoe variable which actually is not used (except assigning it a value)
and confusing break out of the family checking loop. Found by Harry Mason.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Harry J Mason <hjm03r@ecs.soton.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The extra rom[0] check is flagging valid temperatures as invalid when
there is already a CRC data transmission check.
w1_therm_read_bin()
if (rom[8] == crc && rom[0])
verdict = 1;
Requiring rom[0] to be non-zero will flag as invalid temperature
conversions when the low byte is zero, specifically the temperatures 0C,
16C, 32C, 48C, -16C, -32C, and -48C.
The CRC check is produced on the device for the previous 8 bytes and is
required to ensure the data integrity in transmission. I don't see why the
extra check for rom[0] being non-zero is in there. Evgeniy Polyakov didn't
know either. Just for a check I unplugged the sensor, executed a
temperature conversion, and read the results. The read was all ff's, which
also failed the CRC, so it doesn't need to protect against a disconnected
sensor.
I have more extensive patches in the work, but these two trivial ones will
do for today. I would like to hear from people who use the ds2490 USB to
one wire dongle. 1 if you would be willing to test the patches as I
currently only have the one sensor on a short parisite powered wire, 2 if
there is any cheap sources for the ds2490.
Signed-off-by: David Fries <david@fries.net>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct the decoding of negative C temperatures. The code did a binary OR
of two bytes to make a 16 bit value, but assignd it to an integer. This
caused the value to not be sign extended and to loose that it was a
negative number in the assignment.
Before the patch (in my freezer),
w1_slave
ed fe 4b 46 7f ff 03 10 e4 : crc=e4 YES
ed fe 4b 46 7f ff 03 10 e4 t=4078
With the patch,
e3 fe 4b 46 7f ff 0d 10 81 : crc=81 YES
e3 fe 4b 46 7f ff 0d 10 81 t=-17
Signed-off-by: David Fries <david@fries.net>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Decrement the slave counter only in ->release() callback instead of both
in ->release() and w1 control.
Patch is based on debug work and preliminary patch made by Henri Laakso.
Henri noticed in debug that this counter becomes negative after w1 slave
device is physically removed.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Henri Laakso <henri.laakso@wapice.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The size argument passed to memset is wrong.
Signed-off-by Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix links to files in Documentation/* in various Kconfig files
Signed-off-by: Dirk Hohndel <hohndel@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch cleans up duplicate includes in
drivers/w1/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
