1) Allow transition to NEED RESET state only from READY state for ISP82xx.
2) Avoid infinite ISP aborts when chip reset fails.
3) Code cleanup to remove some of the unused debug code.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The problem occurring is a hw-race where there's an outstanding read-flash
operation occurring while the chip is being reset (done via an sg_reset script).
After the chip is paused, the read-flash operation never completes and the
DPC thread, while trying to complete the reset, is never able to recover,
as the HW appears to be hung...
The fix is to wait for outstanding flash operation prior to doing a sg_reset -h.
And to wait for reset to complete before any flash operations.
Note, during the wait, if any of the operation (reset/flash) does not complete,
failure is returned to the upper layer. The upper layer either need to
fail or retry.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The qla2xxx driver uses a port_id_t to mark the start of its enumerations. gcc
is complaining that wrap.b24 may be used uninitialized, but this doesn't look
to be possible. Silence it.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently we can only issue the task management (TM)
commands via the mailbox mechanism. This is a limitation,
since only one mailbox command can be issued at a time.
The purpose of this effort is to provide support for
issuing and processing the respose to TM and Marker
IOCBs asynchronously. Towards achieving this, the
consolidated srb architecture that is currently used for
BSG and IOCB/Logio commands has been enhanced and used.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently, BSG and IOCB/Logio commands have a different
framework (srb structs). The purpose of this effort is to
consolidate them into a generalized framework for these
as well as other asynchronous operations in the future.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Migrate to a consistent set of debug entries during status-IOCB
handling:
* group CS_TIMEOUT handling with CS_PORT_UNAVAILABLE and the like
(more regrouping of common behaviour).
* drop CS_DATA_OVERRUN handling as it now falls into the
'default' case (still returns DID_ERROR).
* consolidate CS_RESET and CS_ABORTED handling, as we the only
functional difference was a printk() (still returns DID_RESET).
* dropped all the earlier inconsistent [qla_]printk()s sprinkled
throught the needlessly large case-statement. Failure case
I/Os are now logged with a 'standard' format:
<command failure details>
<command generic details>
so, for example a dropped-frame is logged as:
qla2xxx 0000:13:00.0: scsi(16:0:0) Dropped frame(s) detected (4000 of 4000 bytes).
qla2xxx 0000:13:00.0: scsi(16:0:0) FCP command status: 0x15-0x18 (70018) \
oxid=78 ser=76 cdb=280000 len=4000 rsp_info=0 resid=0 fw_resid=4000
which should now convey all relevant information.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The driver should not be unloaded if any application is using it.
To disallow driver unload, driver use count must be incremented.
Application uses this char device as handle and increases driver
use count to avoid possible driver unload.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently error status is cleared only after the uncorrectable fatal errors
in the qla2xxx_pci_slot_reset. This fix is added to clear the error status in
qla2xxx_pci_resume. This way for both fatal and non-fatal errors the error
status gets cleared properly.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=572258
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
With qla2xxx using mid-layer async-scsi-scanning, the link state for
disconnected port is displayed wrong. Additional check for cable presence
is considered to display proper link state.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Enhanced the driver to support new FCoE host bus adapter.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The default is enabled since 7e47e5ca18.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The qla84xx_mgmt_cmd function supports multiple subcommands.
Some subcommands require DMA memory and some do not.
Therefore check before freeing DMA memory whether it is allocated or not.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1. Segregate BSG interface specific code to new files.
2. Handle multiple vendor specific commands indepedently.
3. Reorganised support for reset, management and update FCoE firmware commands.
4. Fixed memory leak issue in Loopback.
5. Added new vendor command to support iiDMA using BSG interface.
6. Proper cleanup of dma mapped and dma allocated buffers for BSG request.
[jejb: fix up conflict and merge in Jiri Slaby lock imbalance patch]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stanse found that one error path in qla24xx_bsg_timeout omits to
unlock ha->hardware_lock. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] qla1280: retain firmware for error recovery
[SCSI] attirbute_container: Initialize sysfs attributes with sysfs_attr_init
[SCSI] advansys: fix regression with request_firmware change
[SCSI] qla2xxx: Updated version number to 8.03.02-k2.
[SCSI] qla2xxx: Prevent sending mbx commands from sysfs during isp reset.
[SCSI] qla2xxx: Disable MSI on qla24xx chips other than QLA2432.
[SCSI] qla2xxx: Check to make sure multique and CPU affinity support is not enabled at the same time.
[SCSI] qla2xxx: Correct vp_idx checking during PORT_UPDATE processing.
[SCSI] qla2xxx: Honour "Extended BB credits" bit for CNAs.
[SCSI] scsi_transport_fc: Make sure commands are completed when rport is offline
[SCSI] libiscsi: Fix recovery slowdown regression
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The fix prevents application path from sending get-firmware-state mbx command
during as isp reset.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
On specific platforms, MSI is unreliable on some of the QLA24xx chips, resulting
in fatal I/O errors under load, as reported in <http://bugs.debian.org/572322>
and by some RHEL customers.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The logic is changed to detect this condition based on following
1) both module parameters are off (ql2xmaxqueues and ql2xmultique_tag).
2) both module parameters are on (ql2xmaxqueues and ql2xmultique_tag).
3) The HBA does not support multi queue.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Checks should only be done for NPIV-capable ISPs. Original code
could result in PORT_UPDATEs being missed on non-NPIV-capable
ISPs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We now enable/disable "Additional Receive Credits" in f/w based on nvram
parameter "Extended_BB_Credits" bit (i.e. Enhanced-Features: at offset 0x196).
This is applicable only for GEN2 CNAs.
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Can be used to balance NIC/FCoE traffic distribution.
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Original code could inadvertently skip the post processing of
port information returned from the SNS scan, if any link-flopping
asynchronous-events were received (noticed in FCAL topologies).
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The explicit logout (LOGO) issued at the end of the callback will
flush (via normal scsi_cmnd->done()) any outstanding commands
(FCP2) the firmware is holding. While iterating through the
outstanding_cmnd array in qla2x00_abort_fcport_cmds(), locking
and unlocking of the hardware spinlock, opens-up the driver to
cases where the processed SRB (sp) could be used after the
command completed from interrupt context.
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Target-level resets are unlikely to complete if done after the
bus (LIP/OLS/NOS) has been reset. Perform target-level resets,
if necessary, prior to hitting the bus.
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix for BSG request cleanup when the request timesout.
Proper release of driver resources used for BSG request during timeout cleanup.
Cc: stable@kernel.org
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Since bsg_job->reply->reply_payload_rcv_len is uninitialized
in case of failure, fc-transport triggers a warning for each command
failed.
Cc: stable@kernel.org
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Original code incorrectly assumed only status-type-0
IOCBs would be queued to the response-queue, and thus all
entries would safely reference a VHA from the IOCB
'handle.'
Cc: stable@kernel.org
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Firmware is loaded from flash for these ISP types.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
qla2xxx: EEH added call to pci_restore_state.
qla2xxx: EEH added delay in slot reset routine.
qla2xxx: EEH moved call to pci_save_state(), see (1).
qla2xxx: EEH additional changes for RHEL5.5.
qla2xxx: EEH added function call, removed function call, see (2).
(1) In qla2xxx_probe_one the call to pci_save_state() has been
moved to after the call to qla2xxx_request_irqs().
(2) Add call to pci_disable_pcie_error_reporting() in remove_one.
Delete call to pci_cleanup_aer_uncorrect_error_status() in pci_resume.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The driver did not account for non-tape devices needing to employ
proper FCP2 recovery. Driver now checks the FCP2-capable flag
only, rather than using a midlayer-determined flag (TYPE_TAPE).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
