A mutex has to be replaced by spinlocks as it can be called from
a context which does not allow sleeping.
The kzalloc flag GFP_KERNEL has to be replaced by GFP_ATOMIC
for the same reason.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
After enabling CONFIG_LOCKDEP and CONFIG_PROVE_LOCKING I get the
following warning when ethtool -s is first called on one of the
forcedeth ports:
=================================
[ INFO: inconsistent lock state ]
2.6.26-rc4 #28
---------------------------------
inconsistent {in-hardirq-W} -> {hardirq-on-W} usage.
ethtool/1985 [HC0[0]:SC0[1]:HE1:SE0] takes:
(&np->lock){++..}, at: [<ffffffffa000c5fd>] nv_set_settings+0xc8/0x3de [forcedeth]
{in-hardirq-W} state was registered at:
[<ffffffffffffffff>] 0xffffffffffffffff
irq event stamp: 3606
hardirqs last enabled at (3605): [<ffffffff8068106f>] _spin_unlock_irqrestore+0x3f/0x68
hardirqs last disabled at (3604): [<ffffffff80680d38>] _spin_lock_irqsave+0x13/0x46
softirqs last enabled at (3534): [<ffffffff80246ba5>] __do_softirq+0xbc/0xc5
softirqs last disabled at (3606): [<ffffffff80680b33>] _spin_lock_bh+0x11/0x41
other info that might help us debug this:
2 locks held by ethtool/1985:
#0: (rtnl_mutex){--..}, at: [<ffffffff80596072>] rtnl_lock+0x12/0x14
#1: (_xmit_ETHER){-+..}, at: [<ffffffffa000c5e8>] nv_set_settings+0xb3/0x3de [forcedeth]
stack backtrace:
Pid: 1985, comm: ethtool Not tainted 2.6.26-rc4 #28
Call Trace:
[<ffffffff8025f190>] print_usage_bug+0x162/0x173
[<ffffffff8025fa8b>] mark_lock+0x231/0x41f
[<ffffffff802607cf>] __lock_acquire+0x4e7/0xcac
[<ffffffff8025fe64>] ? trace_hardirqs_on+0xf1/0x115
[<ffffffff80272c3a>] ? disable_irq_nosync+0x6f/0x7b
[<ffffffff80261375>] lock_acquire+0x55/0x6e
[<ffffffffa000c5fd>] ? :forcedeth:nv_set_settings+0xc8/0x3de
[<ffffffff80680b15>] _spin_lock+0x2f/0x3c
[<ffffffffa000c5fd>] :forcedeth:nv_set_settings+0xc8/0x3de
[<ffffffff8058f8bb>] dev_ethtool+0x186/0xea3
[<ffffffff8067f446>] ? mutex_lock_nested+0x243/0x275
[<ffffffff8025df2b>] ? debug_mutex_free_waiter+0x46/0x4a
[<ffffffff8067f469>] ? mutex_lock_nested+0x266/0x275
[<ffffffff8058e1ce>] dev_ioctl+0x4eb/0x600
[<ffffffff8068106f>] ? _spin_unlock_irqrestore+0x3f/0x68
[<ffffffff80580f91>] sock_ioctl+0x1f5/0x202
[<ffffffff802a322e>] vfs_ioctl+0x2a/0x77
[<ffffffff802a34d6>] do_vfs_ioctl+0x25b/0x270
[<ffffffff806807b6>] ? trace_hardirqs_on_thunk+0x35/0x3a
[<ffffffff802a352d>] sys_ioctl+0x42/0x65
[<ffffffff8021fffb>] system_call_after_swapgs+0x7b/0x80
This is caused by the following snippet in nv_set_settings:
netif_carrier_off(dev);
if (netif_running(dev)) {
nv_disable_irq(dev);
netif_tx_lock_bh(dev);
spin_lock(&np->lock);
/* stop engines */
nv_stop_rxtx(dev);
spin_unlock(&np->lock);
netif_tx_unlock_bh(dev);
}
Because of nv_disable_irq this is probably not really a problem
though (I guess) and replacing the spin_lock with spin_lock_irqsave
could keep interrupts disabled for a longer period of time because
of delays in nv_stop_rx and nv_stop_tx.
Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 4c13eb6657 ([ETH]: Make
eth_type_trans set skb->dev like the other *_type_trans) removed
skb->dev assignment from hdlc_fr.c:fr_rx(). Unfortunately it was also
needed for cases other than eth_type_trans().
Adding it back.
It's quite serious and may be a security risk as it causes a wrong
input interface indication (the physical hdlcX instead of logical
pvcX). Probably -stable class fix.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'i2c-fix' of git://aeryn.fluff.org.uk/bjdooks/linux:
I2C: S3C2410: Add MODULE_ALIAS() for s3c2440 device.
I2C: S3C2410: Fixup error codes returned rom a transfer.
I2C: S3C2410: Check ACK on byte transmission
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (8178): uvc: Fix compilation breakage for the other drivers, if uvc is selected
V4L/DVB (8145a): USB Video Class driver
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5131/1: Annotate platform_secondary_init with trace_hardirqs_off
[ARM] 5117/1: pxafb: fix __devinit/exit annotations
[ARM] Export dma_sync_sg_for_device()
[ARM] 5109/1: Mark rtc sa1100 driver as wakeup source before registering it
[ARM] 5116/1: pxafb: cleanup and fix order of failure handling
[ARM] 5115/1: pxafb: fix ifdef for command line option handling
ARM: OMAP: Correcting the gpmc prefetch control register address
ARM: OMAP: DMA: Don't mark channel active in omap_enable_channel_irq
Not sure how this came to get inverted but it appears to have been my
mess up.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.26' of git://neil.brown.name/md:
Fix error paths if md_probe fails.
Don't acknowlege that stripe-expand is complete until it really is.
Ensure interrupted recovery completed properly (v1 metadata plus bitmap)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (55 commits)
net: fib_rules: fix error code for unsupported families
netdevice: Fix wrong string handle in kernel command line parsing
net: Tyop of sk_filter() comment
netlink: Unneeded local variable
net-sched: fix filter destruction in atm/hfsc qdisc destruction
net-sched: change tcf_destroy_chain() to clear start of filter list
ipv4: fix sysctl documentation of time related values
mac80211: don't accept WEP keys other than WEP40 and WEP104
hostap: fix sparse warnings
hostap: don't report useless WDS frames by default
textsearch: fix Boyer-Moore text search bug
netfilter: nf_conntrack_tcp: fixing to check the lower bound of valid ACK
ipv6 route: Convert rt6_device_match() to use RT6_LOOKUP_F_xxx flags.
netlabel: Fix a problem when dumping the default IPv6 static labels
net/inet_lro: remove setting skb->ip_summed when not LRO-able
inet fragments: fix race between inet_frag_find and inet_frag_secret_rebuild
CONNECTOR: add a proc entry to list connectors
netlink: Fix some doc comments in net/netlink/attr.c
tcp: /proc/net/tcp rto,ato values not scaled properly (v2)
include/linux/netdevice.h: don't export MAX_HEADER to userspace
...
When scheduled swaps occur, we need to blit between front & back
buffers. If the buffers are tiled, we need to set the appropriate
XY_SRC_COPY tile bit, but only on 965 chips, since it will cause
corruption on pre-965 (e.g. 945).
Bug reported by and fix tested by Tomas Janousek <tomi@nomi.cz>.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 656acd2bbc ("Input: fix locking in
force-feedback core") causes the following regression on m68k:
| linux/drivers/input/ff-core.c: In function 'input_ff_upload':
| linux/drivers/input/ff-core.c:172: error: dereferencing pointer to incomplete type
| linux/drivers/input/ff-core.c: In function 'erase_effect':
| linux/drivers/input/ff-core.c:197: error: dereferencing pointer to incomplete type
| linux/drivers/input/ff-core.c:204: error: dereferencing pointer to incomplete type
| make[4]: *** [drivers/input/ff-core.o] Error 1
As the incomplete type is `struct task_struct', including <linux/sched.h> fixes
it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Handle .reset_resume() so that libertas can survive suspend/resume without
reloading the firmware.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Deepak Saxena <dsaxena@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the problem to keep mac80211 resubmitting SKBs
when Tx request cannot be met in monitor mode.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the rates reported in monitor mode operation
(Wireshark) for iwlwifi.
Previously, packets with rates of 6M..24M would be reported
incorrectly and packets with rates of 36M..54M would not passed
up the stack.
Signed-off-by: Rick Farrington <rickdic@hotmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During the development of the physical PCI slot patch series, Gary Hade
kept on reporting strange oopses due to interactions between pci_slot
and acpiphp.
http://lkml.org/lkml/2007/11/28/319
find_root_bridges() unconditionally installs
handle_hotplug_event_bridge() as an ACPI_SYSTEM_NOTIFY handler for all
root bridges.
However, during module cleanup, remove_bridge() will only remove the
notify handler iff the root bridge had a hot-pluggable slot directly
underneath. That is:
root bridge -> hotplug slot
But, if the topology looks like either of the following:
root bridge -> non-hotplug slot
root bridge -> p2p bridge -> hotplug slot
Then we currently do not remove the notify handler from that root
bridge.
This can cause a kernel oops if we modprobe acpiphp later and it gets
loaded somewhere else in memory. If the root bridge then receives a
hotplug event, it will then attempt to call a stale, non-existent notify
handler and we blow up.
Much thanks goes to Gary Hade for his persistent debugging efforts.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the
VPD end tag will hang the device. This problem was initially
observed when a vpd entry was created in sysfs
('/sys/bus/pci/devices/<id>/vpd'). A read to this sysfs entry
will dump 32k of data. Reading a full 32k will cause an access
beyond the VPD end tag causing the device to hang. Once the device
is hung, the bnx2 driver will not be able to reset the device.
We believe that it is legal to read beyond the end tag and
therefore the solution is to limit the read/write length.
A majority of this patch is from Matthew Wilcox who gave code for
reworking the PCI vpd size information. A PCI quirk added for the
Broadcom NIC's to limit the read/write's.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
UVC makefile defines obj as:
obj-$(CONFIG_USB_VIDEO_CLASS) := uvcvideo.o
Instead of:
obj-$(CONFIG_USB_VIDEO_CLASS) += uvcvideo.o
Due to that, if uvc is selected, all obj-y or obj-m that were added to
compilation were forget. This breaks a proper kernel build.
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add cond_resched() to prevent monopolising CPU when processing large bios.
dm-crypt processes encryption of bios in sector units. If the bio request
is big it can spend a long time in the encryption call.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Tested-by: Yan Li <elliot.li.tech@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Some PCI devices will lock up if we attempt to read from VPD addresses
beyond some device-dependent limit. Until we can identify these
devices and adjust the file size accordingly, only let root read VPD
through sysfs to prevent a DoS by normal users.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add a MODULE_ALIAS() statement for the i2c-s3c2410 controller
to ensure that it can be autoloaded on the S3C2440 systems that
we support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The driver should be returning -ENXIO for transfers that do not
pass the initial address byte stage.
Note, also small tidyups to the driver comments in the area.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We should check for the reception of an ACK after transmitting each
data byte. The address send has been correctly checking this, but the
data write byte state should have also been checking for these failures.
As part of the same fix, we remove the ACK checking from the receive
path where it should not have been checking for an ACK which our hardware
was sending.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This driver supports video input devices compliant with the USB Video Class
specification. This means lots of currently manufactured webcams, and probably
most of the future ones.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rewrite AID calculation in handle_pspoll() to avoid truncating bits.
Make hostap_80211_header_parse() static, don't export it. Avoid
shadowing variables.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DEBUG_EXTRA is reported to the kernel log by default, but DEBUG_EXTRA2
is not. Unrelated WDS frames pollute the log unnecessarily.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we support warm-plug mate port will be registered
even if there are no devices attached to it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This reverts commit ac1623625c.
It was premature to remove it now, we will do it post-2.6.26.
Thanks to Russell King for noticing the issue.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The newly added event_lock spinlock in the input core disallows sleeping
and therefore using mutexes in event handlers. Convert force-feedback
core to rely on event_lock instead of mutex to protect slots allocated
for fore-feedback effects. The original mutex is still used to serialize
uploading and erasing of effects.
Reported-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (42 commits)
V4L/DVB (8108): Fix open/close race in saa7134
V4L/DVB (8100): V4L/vivi: fix possible memory leak in vivi_fillbuff
V4L/DVB (8097): xc5000: check device hardware state to determine if firmware download is needed
V4L/DVB (8096): au8522: prevent false-positive lock status
V4L/DVB (8092): videodev: simplify and fix standard enumeration
V4L/DVB (8075): stv0299: Uncorrected block count and bit error rate fixed
V4L/DVB (8074): av7110: OSD transfers should not be interrupted
V4L/DVB (8073): av7110: Catch another type of ARM crash
V4L/DVB (8071): tda10023: Fix possible kernel oops during initialisation
V4L/DVB (8069): cx18: Fix S-Video and Compsite inputs for the Yuan MPC718 and enable card entry
V4L/DVB (8068): cx18: Add I2C slave reset via GPIO upon initialization
V4L/DVB (8067): cx18: Fix firmware load for case when digital capture happens first
V4L/DVB (8066): cx18: Fix audio mux input definitions for HVR-1600 Line In 2 and FM radio
V4L/DVB (8063): cx18: Fix unintended auto configurations in cx18-av-core
V4L/DVB (8061): cx18: only select tuner / frontend modules if !DVB_FE_CUSTOMISE
V4L/DVB (8048): saa7134: Fix entries for Avermedia A16d and Avermedia E506
V4L/DVB (8044): au8522: tuning optimizations
V4L/DVB (8043): au0828: add support for additional USB device id's
V4L/DVB (8042): DVB-USB UMT-010 channel scan oops
V4L/DVB (8040): soc-camera: remove soc_camera_host_class class
...
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
dock: bay: Don't call acpi_walk_namespace() when ACPI is disabled.
ACPI: don't walk tables if ACPI was disabled
thermal: Create CONFIG_THERMAL_HWMON=n
I got a problem when I wanted to check if the kernel supports process
event connector, and It seems there's no way to do this check.
At best I can check if the kernel supports connector or not, by looking
into /proc/net/netlink, or maybe checking the return value of bind() to
see if it's ENOENT.
So it would be useful to add /proc/net/connector to list all supported
connectors:
# cat /proc/net/connector
Name ID
connector 4294967295:4294967295
cn_proc 1:1
w1 3:1
Changelog:
- fix memory leak: s/seq_release/single_release
- use spin_lock_bh instead of spin_lock_irqsave
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
md_probe can fail (e.g. alloc_disk could fail) without
returning an error (as it alway returns NULL).
So when we call mddev_find immediately afterwards, we need
to check that md_probe actually succeeded. This means checking
that mdev->gendisk is non-NULL.
cc: <stable@kernel.org>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Neil Brown <neilb@suse.de>
We shouldn't acknowledge that a stripe has been expanded (When
reshaping a raid5 by adding a device) until the moved data has
actually been written out. However we are currently
acknowledging (by calling md_done_sync) when the POST_XOR
is complete and before the write.
So track in s.locked whether there are pending writes, and don't
call md_done_sync yet if there are.
Note: we all set R5_LOCKED on devices which are are about to
read from. This probably isn't technically necessary, but is
usually done when writing a block, and justifies the use of
s.locked here.
This bug can lead to a crash if an array is stopped while an reshape
is in progress.
Cc: <stable@kernel.org>
Signed-off-by: Neil Brown <neilb@suse.de>
If, while assembling an array, we find a device which is not fully
in-sync with the array, it is important to set the "fullsync" flags.
This is an exact analog to the setting of this flag in hot_add_disk
methods.
Currently, only v1.x metadata supports having devices in an array
which are not fully in-sync (it keep track of how in sync they are).
The 'fullsync' flag only makes a difference when a write-intent bitmap
is being used. In this case it tells recovery to ignore the bitmap
and recovery all blocks.
This fix is already in place for raid1, but not raid5/6 or raid10.
So without this fix, a raid1 ir raid4/5/6 array with version 1.x
metadata and a write intent bitmaps, that is stopped in the middle
of a recovery, will appear to complete the recovery instantly
after it is reassembled, but the recovery will not be correct.
If you might have an array like that, issueing
echo repair > /sys/block/mdXX/md/sync_action
will make sure recovery completes properly.
Cc: <stable@kernel.org>
Signed-off-by: Neil Brown <neilb@suse.de>
There is a small off-by-one bug in firewire-sbp2. This causes problems
when a device exports multiple LUN Directories. I found it when trying
to talk to a SONY DVD Jukebox.
Signed-off-by: Richard Sharpe <realrichardsharpe@gmail.com>
Acked-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (op. order, changelog)
clock is already cpu-endian (see le32_to_cpu slightly before), so
le64_to_cpu doesn't make much sense.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a circular locking dependency in the workqueue handling.
The interface work task uses the mac80211 function
ieee80211_iterate_active_interfaces() which grabs the RTNL lock.
However when the interface is brough down, this happens under the RTNL
lock as well, this causes problems because mac80211 will flush the workqueue
during the ifdown event. This causes mac80211 to wait until the driver has
completed all work which can't finish because it is waiting on the RTNL lock.
This is fixed by moving rt2x00 workqueue tasks on a different workqueue,
this workqueue can be flushed when the ieee80211_hw structure is removed
by the driver (when the driver is unloaded) which does not happen under the
RTNL lock.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dev_close() must be called holding the RTNL. Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dev_close() must be called holding the RTNL. Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
s2io has IOMMU overflow checking, but unfortunately it is wrong.
It didn't use the standard macros, which meant that it only worked
on POWER and SPARC because only those define DMA_ERROR_CODE. Convert it to
use the standard macros instead.
I also commented two more bugs in the IOMMU handling. It assumes
that 0 DMA addresses cannot happen, but that's not true in all IOMMU setups.
The information if a buffer has been already mapped needs to be stored
elsewhere.
Didn't fix those because it needs careful checking of the buffer handling
by the maintainers.
Cc: ram.vepa@neterion.com
Cc: santosh.rastapur@neterion.com
Cc: sivakumar.subramani@neterion.com
Cc: sreenivasa.honnur@neterion.com
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When enabling TSO via ethool on e1000, it is possible to set
NETIF_F_TSO6 on hardware that does not support it. Setting TSO via
ethtool now matches the settings used when the hardware is probed.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The E100 device can't work on current kernel (2.6.26-rc6) and will cause
kernel corruption on intel ixdp4xx.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
