Earlier I reported that Matthew's acpiphp rewrite had problem in powering down
slot on my i386 system. The following patch is needed to get the acpiphp
rewrite properly powering down the slot.
Signed-off-by: Dely Sy <dely.l.sy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A root bridge may not have directly attached hotpluggable slots under it.
Instead, it may have p2p bridges with slots under it. In this case, we need
to clean up the p2p bridges and slots properly too. Patch below applies on
top of the original patch, and fixes this problem. Without this, acpiphp
leaves behind notify handlers on module unload, and subsequent module load
attempts don't work properly too. Patch was tested on an ia64 Tiger4 box.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts acpiphp to use the generic PCI resource assignment code.
It's quite large, but most of it is deleting the acpiphp_pci and acpiphp_res
files. It's tested on an hp Integrity rx8620 (which won't work without this
patch). Testers with other hardware welcomed.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When hot-plugging an I/O hierarchy that contains many bridges and leaf
devices, it's possible that there are not enough resources to start all the
device present. If we fail to assign a resource, clear the corresponding
value in the pci_dev structure, so other code can take corrective action.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a root bridge hierarchy is hot-plugged, resource requirements for the new
devices may be greater than what the root bridge is decoding. In this case,
we want to remove devices that did not get needed resources. These devices
have been scanned into bus specific lists but not yet added to the global
device list. Make sure the pci remove functions can handle this case.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a pci child bus is created, add it to the parent's children list
immediately rather than waiting till pci_bus_add_devices(). For hot-plug
bridges/devices, pci_bus_add_devices() may be called much later, after they
have been properly configured. In the meantime, this allows us to use the
normal pci bus search functions for the hot-plug bridges/buses.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With root bridge and pci bridge hot-plug, new buses and devices can be added
or removed at run time. Protect the pci bus and device lists with the pci
lock when doing so.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When hot-plugging a root bridge, as we try to assign bus numbers we may find
that the hotplugged hieratchy has more PCI to PCI bridges (i.e. bus
requirements) than available. Make sure we don't step over an existing bus
when that happens.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When you hot-plug a (root) bridge hierarchy, it may have p2p bridges and
devices attached to it that have not been configured by firmware. In this
case, we need to configure the devices before starting them. This patch
separates device start from device scan so that we can introduce the
configuration step in the middle.
I kept the existing semantics for pci_scan_bus() since there are a huge number
of callers to that function.
Also, I have no way of testing the changes I made to the parisc files, so this
needs review by those folks. Sorry for the massive cross-post, this touches
files in many different places.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Friday, March 25, 2005 8:47 PM Greg KH wrote:
>Here's a fix for pci express. For some reason I don't think they are
>using the driver model properly here, but I could be wrong...
Thanks for making the changes. However, changes in functions:
void pcie_port_device_remove(struct pci_dev *dev) and
static int remove_iter(struct device *dev, void *data)
are not correct. Please use the patch, which is based on kernel
2.6.12-rc1, below for a fix for these.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sysfs: fix drivers/pci so if an attribute does not implement
show or store method read/write will return -EIO
instead of 0.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The git commit 794f5bfa77
accidentally suffers from a previous typo in that file
(',' instead of ';' in end of line). Patch included.
Signed-off-by: Mika Kukkonen (mikukkon@iki.fi)
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are many drivers that have been setting the generic driver
model level shutdown callback, and pci thus must not override it.
Without this patch we can have really bad data loss on various
raid controllers.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On 64-bit machines, PCI_BASE_ADDRESS_MEM_MASK and other mask constants
passed to pci_size() are 64-bit (for example ~0x0fUL). However, pci_size
does comparisons between the u32 arguments and the mask, which will fail
even though any result from pci_size is still just 32-bit.
Changing the mask argument to u32 seems the obvious thing to do, since all
arithmetic in the function is 32-bit and having a larger mask makes no
sense.
This triggered on a PPC64 system here where an adapter (VGA, as it
happened) had a memory region base of 0xfe000000 and a sz of the same,
matching the if (max == maxbase ...) test at the bottom of pci_size but
failing the mask comparison. Quite a corner case which I guess explains
why we haven't seen it until now.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MSI functionality is broken on the GC_LE x86 chipset that Serverworks
developed and that is being used in various platforms today. Broadcom is
going to push out to the kernel MSI enabled Gigabit drivers (in the very
near future), and we would like to make sure that MSI does not get
enabled on any platforms using the GC_LE chipset (device id 0x17).
Following the AMD 8131 example, I am including a patch to disable MSI
functionality when a GCNB_LE is detected. Please let me know if there
are any issues with this. This is a permanent fix for this chipset, as
the hardware will not be updated.
Signed-off-by: Narendra Sankar <nsankar@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a patch that fixes up the pci_dev refcounting in the CPCI code.
I've done some testing against it and it seems fine here.
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At least some VIA chipsets require the fixup even in IO-APIC mode.
This was found and debugged with the patient assistance of Stian
Jordet <liste@jordet.nu> on an Asus CUV266-DLS motherboard.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is my third attempt at a patch to further update the CompactPCI
hotplug driver infrastructure to address the pci_enable_device issue
discussed on the list as well as a few other issues I discovered during
some more testing. This version addresses a few more issues pointed out
by Prarit Bhargava. Changes include:
- cpci_enable_device and its recursive calling of pci_enable_device on
new devices removed.
- Use list_rwsem to avoid slot status change races between disable_slot
and check_slots.
- Fixed oopsing in cpci_hp_unregister_bus caused by calling list_del on
a slot after calling pci_hp_deregister.
- Removed kfree calls in cleanup_slots since release_slot will have
done it already.
- Reworked init_slots a bit to fix latch and adapter file updating on
subsequent calls to cpci_hp_start.
- Improved sanity checking in cpci_hp_register_controller.
- Now shut things down correctly in cpci_hotplug_exit.
- Switch to pci_get_slot instead of deprecated pci_find_slot.
- A bunch of CodingStyle fixes.
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current shpchp driver doesn't seem to program command register to
enable PERR and SERR properly. The following patch fixes this issue.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current shpchp driver doesn't seem to program _HPP values
properly. The following patch fixes this issue.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Delete quirk_via_bridge(), restore quirk_via_irqpic() -- but now
improved to be invoked upon device ENABLE, and now only for VIA devices
-- not all devices behind VIA bridges.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If my CPCI hotplug update patch is applied, then there are no longer any
in tree users of the pci_visit_dev API, and it and its related code can be
removed.
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] CPCI: update
I have finally done some work to update the CompactPCI hotplug driver to
fix some of the outstanding issues in 2.6:
- Added adapter and latch status ops so that those files will get created
by the current PCI hotplug core. This used to not be required, but
seems to be now after some of the sysfs rework in the core.
- Replaced slot list spinlock with a r/w semaphore to avoid any potential
issues with sleeping. This quiets all of the runtime warnings.
- Reworked interrupt driven hot extraction handling to remove need for a
polling operator for ENUM# status. There are a lot of boards that only
have an interrupt driven by ENUM#, so this lowers the bar to entry.
- Replaced pci_visit_dev usage with better use of the PCI core functions.
The new code is functionally equivalent to the previous code, but the
use of pci_enable_device on insert needs to be investigated further, as
I need to do some more testing to see if it is still necessary.
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is the updated patch to get pciehp driver to work for downstream
port of a switch and handle the difference in the offset value of PCI
Express capability list item of different ports.
Signed-off-by: Dely Sy <dely.l.sy@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch to fix the problem of echoing 1 to "power" file
to enabled slot causing the slot to power down, and echoing 0
to disabled slot causing shpchp_disabled_slot() to be called
twice. This problem was reported by kenji Kaneshige.
Thanks,
Dely
Signed-off-by: Dely Sy <dely.l.sy@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I fogot to remove the code that freed the memory in cleanup_slots().
Here is the new patch, which I have also taken care of the comment
by Eike to remove the cast in hotplug_slot->private.
Signed-off-by: Dely Sy <dely.l.sy@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch just adds Intel's Hance Rapid south bridge IDs to ICH4 region quirk.
Patch was successfuly tested by Chunhao Huang from Winbond.
Signed-Off-By: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
here is the patch that fixes the bug introduced by my previous patch which
already went into 2.6.12-rc2 and is likely to cause trouble is someone hits
one the else case here by accident.
Using the &= operation before the if statement destroys the information the
if asks for so we always go into the else branch.
Signed-off-by: Rolf Eike Beer <eike-hotplug@sf-tec.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now pci drivers can know when the system is going down without having to
add a reboot notifier event.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the possibility to do word-aligned 16-bit atomic PCI
configuration space accesses via the sysfs PCI interface. As a result, problems
with Emulex LFPC on IBM PowerPC64 are fixed.
Patch is present in SLES 9 SP1.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I think 'is_enabled' flag in pci_dev structure should be set/cleared
when the device actually enabled/disabled. Especially about
pci_enable_device(), it can be failed. By this change, we will also
get the possibility of refering 'is_enabled' flag from the functions
called through pci_enable_device()/pci_disable_device().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some KernelDoc descriptions are updated to match the current code.
No code changes.
Signed-off-by: Martin Waitz <tali@admingilde.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the Intel ESB2 DID's to the ata_piix.c and quirks.c file for
IDE mode SATA support.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
