Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Pull Tile arch updates from Chris Metcalf:
"These changes bring in a bunch of new functionality that has been
maintained internally at Tilera over the last year, plus other stray
bits of work that I've taken into the tile tree from other folks.
The changes include some PCI root complex work, interrupt-driven
console support, support for performing fast-path unaligned data
fixups by kernel-based JIT code generation, CONFIG_PREEMPT support,
vDSO support for gettimeofday(), a serial driver for the tilegx
on-chip UART, KGDB support, more optimized string routines, support
for ftrace and kprobes, improved ASLR, and many bug fixes.
We also remove support for the old TILE64 chip, which is no longer
buildable"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (85 commits)
tile: refresh tile defconfig files
tile: rework <asm/cmpxchg.h>
tile PCI RC: make default consistent DMA mask 32-bit
tile: add null check for kzalloc in tile/kernel/setup.c
tile: make __write_once a synonym for __read_mostly
tile: remove support for TILE64
tile: use asm-generic/bitops/builtin-*.h
tile: eliminate no-op "noatomichash" boot argument
tile: use standard tile_bundle_bits type in traps.c
tile: simplify code referencing hypervisor API addresses
tile: change <asm/system.h> to <asm/switch_to.h> in comments
tile: mark pcibios_init() as __init
tile: check for correct compiler earlier in asm-offsets.c
tile: use standard 'generic-y' model for <asm/hw_irq.h>
tile: use asm-generic version of <asm/local64.h>
tile PCI RC: add comment about "PCI hole" problem
tile: remove DEBUG_EXTRA_FLAGS kernel config option
tile: add virt_to_kpte() API and clean up and document behavior
tile: support FRAME_POINTER
tile: support reporting Tilera hypervisor statistics
...
dct_base and dct_limit obtain 32 bit register values when they read
their respective pci config space registers. A left shift beyond 32 bits
will cause them to wrap around. Similar case for chan_addr as can be
seen from the bug report (link below). In the patch, we rectify this by
casting chan_addr to u64 and by comparing dct_base and dct_limit against
properly shifted sys_addr in order to compare the correct bits.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Link: http://lkml.kernel.org/r/20130819132302.GA12171@elgon.mountain
Signed-off-by: Borislav Petkov <bp@suse.de>
Basically we want to cover all 0x0-0xf models, i.e. Orochi and later.
Cc: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Link: http://lkml.kernel.org/r/20130819192321.GF4165@pd.tnic
Signed-off-by: Borislav Petkov <bp@suse.de>
The struct should be terminated by using empty braces in order to
fix the following sparse warning.
drivers/edac/cpc925_edac.c:792:10: warning: Using plain integer as NULL pointer
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
[ drop obvious comment ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Now that we cache (family, model, stepping) locally, use them instead of
boot_cpu_data.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
On newer models, support has been included for upto 4 DCT's, however,
only DCT0 and DCT3 are currently configured (cf BKDG Section 2.10).
Also, the routing DRAM Requests algorithm is different for F15h M30h.
Thus it is cleaner to use a brand new function rather than adding quirks
to the more generic f1x_match_to_this_node(). Refer to "2.10.5 DRAM
Routing Requests" in the BKDG for further info.
Tested on Fam15h M30h with ECC turned on using mce_amd_inj facility and
verified to be functionally correct.
While at it, verify if erratum workarounds for E505 and E637 still hold.
From email conversations within AMD, the current status of the errata
is:
* Erratum 505: fixed in model 0x1, stepping 0x1 and later.
* Erratum 637: not fixed.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
[ Cleanups, corrections ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Make a local function static in order to fix the following sparse
warning:
drivers/edac/x38_edac.c:252:14: warning: symbol 'x38_map_mchbar' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
[ Boris: Correct commit message ]
Signed-off-by: Borislav Petkov <bp@suse.de>
This local symbol is used only in this file.
Fix the following sparse warnings:
drivers/edac/i3200_edac.c:264:14: warning: symbol 'i3200_map_mchbar' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
It can happen that configurations are running in a single-channel mode
even with a dual-channel memory controller, by, say, putting the DIMMs
only on the one channel and leaving the other empty. This causes a
problem in init_csrows which implicitly assumes that when the second
channel is enabled, i.e. channel 1, the struct dimm hierarchy will be
present. Which is not.
So always allocate two channels unconditionally.
This provides for the nice side effect that the data structures are
initialized so some day, when memory hotplug is supported, it should
just work out of the box when all of a sudden a second channel appears.
Reported-and-tested-by: Roger Leigh <rleigh@debian.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
The usage of strict_strtol() is not preferred, because strict_strtol()
is obsolete. Thus, kstrtol() should be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
Add a new error signature for Family 15h, models 30h-3fh. Patch has been
tested on Fam15h using mce_amd_inj facility and has been verified to
work correctly.
Signed-off-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
[ cleanup commit message and error string ]
Signed-off-by: Borislav Petkov <bp@suse.de>
The usage of strict_strtoul() is not preferred, because strict_strtoul()
is obsolete. Thus, kstrtoul() should be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Ever since commit 45f035ab9b ("CONFIG_HOTPLUG should be always on"),
it has been basically impossible to build a kernel with CONFIG_HOTPLUG
turned off. Remove all the remaining references to it.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix yet another issue caught by 8f46baaa7e ("base: core: WARN() about
bogus permissions on device attributes").
Signed-off-by: Borislav Petkov <bp@suse.de>
I get the following warning on boot:
------------[ cut here ]------------
WARNING: at drivers/base/core.c:575 device_create_file+0x9a/0xa0()
Hardware name: -[8737R2A]-
Write permission without 'store'
...
</snip>
Drilling down, this is related to dynamic channel ce_count attribute
files sporting a S_IWUSR mode without a ->store() function. Looking
around, it appears that they aren't supposed to have a ->store()
function. So remove the bogus write permission to get rid of the
warning.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: <stable@vger.kernel.org> # 3.[89]
[ shorten commit message ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Pull edac fixes from Mauro Carvalho Chehab:
"Two edac fixes:
- i7300_edac currently reports a wrong number of DIMMs when the
memory controller is in single channel mode
- on some Sandy Bridge machines, the EDAC driver bails out as one of
the PCI IDs used by the driver is hidden by BIOS. As the driver
uses it only to detect the type of memory, make it optional at the
driver"
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
edac: sb_edac.c should not require prescence of IMC_DDRIO device
i7300_edac: Fix memory detection in single mode
The Sandy Bridge EDAC driver uses a register in the IMC_DDRIO CSR
space to determine the type of DIMMs (registered or unregistered).
But this device does not exist on some single socket Sandy Bridge
servers. While the type of DIMMs is nice to know, it is not essential
for this driver's other functions. So it seems harsh to have it
refuse to load at all when it cannot find this device.
Make the check for this device be optional. If it isn't present
just report the memory type as "MEM_UNKNOWN".
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add code to handle DRAM ECC errors decoding for Fam16h.
Tested on Fam16h with ECC turned on using the mce_amd_inj facility and
works fine.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
[ Boris: cleanups and clarifications ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Both mci.mem_is_per_rank and mci.csbased denote the same thing: the
memory controller is csrows based. Merge both fields into one.
There's no need for the driver to actually fill it, as the core detects
it by checking if one of the layers has the csrows type as part of the
memory hierarchy:
if (layers[i].type == EDAC_MC_LAYER_CHIP_SELECT)
per_rank = true;
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
We were filling the csrow size with a wrong value. 16a528ee39 ("EDAC:
Fix csrow size reported in sysfs") tried to address the issue. It fixed
the report with the old API but not with the new one. Correct it for the
new API too.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[ make it a per-csrow accounting regardless of ->channel_count ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Pull EDAC fixes and ghes-edac from Mauro Carvalho Chehab:
"For:
- Some fixes at edac drivers (i7core_edac, sb_edac, i3200_edac);
- error injection support for i5100, when EDAC debug is enabled;
- fix edac when it is loaded builtin (early init for the subsystem);
- a "Firmware First" EDAC driver, allowing ghes to report errors via
EDAC (ghes-edac).
With regards to ghes-edac, this fixes a longstanding BZ at Red Hat
that happens with Nehalem and Sandy Bridge CPUs: when both GHES and
i7core_edac or sb_edac are running, the error reports are
unpredictable, as both BIOS and OS race to access the registers. With
ghes-edac, the EDAC core will refuse to register any other concurrent
memory error driver.
This patchset moves the ghes struct definitions to a separate header
file (include/acpi/ghes.h) and adds 3 hooks at apei/ghes.c to
register/unregister and to report errors via ghes-edac. Those changes
were acked by ghes driver maintainer (Huang)."
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: (30 commits)
i5100_edac: convert to use simple_open()
ghes_edac: fix to use list_for_each_entry_safe() when delete list items
ghes_edac: Fix RAS tracing
ghes_edac: Make it compliant with UEFI spec 2.3.1
ghes_edac: Improve driver's printk messages
ghes_edac: Don't credit the same memory dimm twice
ghes_edac: do a better job of filling EDAC DIMM info
ghes_edac: add support for reporting errors via EDAC
ghes_edac: Register at EDAC core the BIOS report
ghes: add the needed hooks for EDAC error report
ghes: move structures/enum to a header file
edac: add support for error type "Info"
edac: add support for raw error reports
edac: reduce stack pressure by using a pre-allocated buffer
edac: lock module owner to avoid error report conflicts
edac: remove proc_name from mci structure
edac: add a new memory layer type
edac: initialize the core earlier
edac: better report error conditions in debug mode
i5100_edac: Remove two checkpatch warnings
...
This removes an open coded simple_open() function and
replaces file operations references to the function
with simple_open() instead.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since we will remove items off the list using list_del() we need
to use a safe version of the list_for_each_entry() macro aptly named
list_for_each_entry_safe().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the current version of CPER, there's no way to associate an
error with the memory error. So, the error location in EDAC
layers is unused.
As CPER has its own idea about memory architectural layers, just
output whatever is there inside the driver's detail at the RAS
tracepoint.
The EDAC location keeps untouched, in the case that, in some future,
we could actually map the error into the dimm labels.
Now, the error message:
[ 72.396625] {1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 0
[ 72.396627] {1}[Hardware Error]: APEI generic hardware error status
[ 72.396628] {1}[Hardware Error]: severity: 2, corrected
[ 72.396630] {1}[Hardware Error]: section: 0, severity: 2, corrected
[ 72.396632] {1}[Hardware Error]: flags: 0x01
[ 72.396634] {1}[Hardware Error]: primary
[ 72.396635] {1}[Hardware Error]: section_type: memory error
[ 72.396637] {1}[Hardware Error]: error_status: 0x0000000000000400
[ 72.396638] {1}[Hardware Error]: node: 3
[ 72.396639] {1}[Hardware Error]: card: 0
[ 72.396640] {1}[Hardware Error]: module: 0
[ 72.396641] {1}[Hardware Error]: device: 0
[ 72.396643] {1}[Hardware Error]: error_type: 18, unknown
[ 72.396666] EDAC MC0: 1 CE reserved error (18) on unknown label (node:3 card:0 module:0 page:0x0 offset:0x0 grain:0 syndrome:0x0 - status(0x0000000000000400): Storage error in DRAM memory)
Is properly represented on the trace event:
kworker/0:2-584 [000] .... 72.396657: mc_event: 1 Corrected error: reserved error (18) on unknown label (mc:0 location👎-1:-1 address:0x00000000 grain:1 syndrome:0x00000000 APEI location: node:3 card:0 module:0 status(0x0000000000000400): Storage error in DRAM memory)
Tested on a 4 sockets E5-4650 Sandy Bridge machine.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide a better infrastructure for printk's inside the driver:
- use edac_dbg() for debug messages;
- standardize the usage of pr_info();
- provide warning about the risk of relying on this
driver.
While here, changes the size of a fake memory to 1 page. This is
as good or as bad as 1000 pages, but it is easier for userspace to
detect, as I don't expect that any machine implementing GHES would
provide just 1 page available ;)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Conflicts:
drivers/edac/ghes_edac.c
Instead of just faking a random value for the DIMM data, get
the information that it is available via DMI table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the EDAC core is capable of just forward the errors via
the userspace API, add a report mechanism for the GHES errors.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register GHES at EDAC MC core, in order to avoid other
drivers to also handle errors and mangle with error data.
The edac core will warrant that just one driver will be used,
so the first one to register (BIOS first) will be the one that
will be reporting the hardware errors.
For now, the EDAC driver does nothing but to register at the
EDAC core, preventing the hardware-driven mechanism to
interfere with GHES.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
The number of variables at the stack is too big.
Reduces the stack usage by using a pre-allocated error
buffer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
APEI GHES and i7core_edac/sb_edac currently can be loaded at
the same time, but those are Highlander modules:
"There can be only one".
There are two reasons for that:
1) Each driver assumes that it is the only one registering at
the EDAC core, as it is driver's responsibility to number
the memory controllers, and all of them start from 0;
2) If BIOS is handling the memory errors, the OS can't also be
doing it, as one will mangle with the other.
So, we need to add an module owner's lock at the EDAC core,
in order to avoid having two different modules handling memory
errors at the same time. The best way for doing this lock seems
to use the driver's name, as this is unique, and won't require
changes on every driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some cases where the memory controller layout is
completely hidden. This is the case of firmware-driven error
code, like the one provided by GHES. Add a new layer to be
used on such memory error report mechanisms.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order for it to work with it builtin, the EDAC core should
be initialized earlier, otherwise the ghes_edac driver initializes
before edac_mc_sysfs_init() being called:
...
[ 4.998373] EDAC MC0: Giving out device to 'ghes_edac.c' 'ghes_edac': DEV ghes
...
[ 4.998373] EDAC MC1: Giving out device to 'ghes_edac.c' 'ghes_edac': DEV ghes
[ 6.519495] EDAC MC: Ver: 3.0.0
[ 6.523749] EDAC DEBUG: edac_mc_sysfs_init: device mc created
The net result is that no EDAC sysfs nodes will appear.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The last changeset introduced a few checkpatch warnings:
WARNING: debugfs_remove_recursive(NULL) is safe this check is probably not required
261: FILE: drivers/edac/i5100_edac.c:1207:
+ if (priv->debugfs)
+ debugfs_remove_recursive(priv->debugfs);
WARNING: debugfs_remove(NULL) is safe this check is probably not required
290: FILE: drivers/edac/i5100_edac.c:1250:
+ if (i5100_debugfs)
+ debugfs_remove(i5100_debugfs);
Get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create a debugfs direcotry i5100_edac/mcX for each memory controller and
add nodes to control how fault injection is preformed.
After configuring an injection using inject_channel, inject_deviceptr1,
inject_deviceptr2, inject_eccmask1, inject_eccmask2 and inject_hlinesel
trigger the injection by writing anything to inject_enable.
Example of a CE injection:
echo 0 > /sys/kernel/debug/i5100_edac/mc0/inject_channel
echo 1 > /sys/kernel/debug/i5100_edac/mc0/inject_hlinesel
echo 61440 > /sys/kernel/debug/i5100_edac/mc0/inject_eccmask1
echo 1 > /sys/kernel/debug/i5100_edac/mc0/inject_enable
Example of UE injection:
echo 0 > /sys/kernel/debug/i5100_edac/mc0/inject_channel
echo 2 > /sys/kernel/debug/i5100_edac/mc0/inject_hlinesel
echo 65535 > /sys/kernel/debug/i5100_edac/mc0/inject_eccmask1
echo 65535 > /sys/kernel/debug/i5100_edac/mc0/inject_eccmask2
echo 17 > /sys/kernel/debug/i5100_edac/mc0/inject_deviceptr1
echo 0 > /sys/kernel/debug/i5100_edac/mc0/inject_deviceptr2
echo 1 > /sys/kernel/debug/i5100_edac/mc0/inject_enable
Sometimes it is needed to enable the injection more then once (echo to
the inject_enable node) for the injection to happen, I am not sure why.
Signed-off-by: Niklas Söderlund <niklas.soderlund@ericsson.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
