Visstrim_M10 boards have an TI tlv320aic3204 codec
attached to SSI1.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It seems vim's autocompletion played tricks on me without me noticing.
This was intruduced in
97976e2 (ARM: mx3: use .init_early to initialize cpu type, reset address and iomuxer)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the "i.MX35 (MCIMX35) Multimedia Applications Processor
Reference Manual" the correct address for the pad control register
IOMUXC_SW_PAD_CTL_PAD_ATA_DATA3 is 0x06ec, not 0x6e8.
Signed-off-by: Ryan Lortie <desrt@desrt.ca>
Acked-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on code created by Lothar Waßmann, Sascha Hauer, Wolfram Sang and
me.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
It is used for example in the i2c driver which can be compiled modular.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This is not strictly necessary but the right thing to do.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This fixes a small memory leak that was only hit in very unlikely error
paths.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- wrong MUX was set before for IRQ
- get_pendown_state is no more needed
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The latter are error-prone because the bank number is one less than one
would read in the documentation.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Eric Benard <eric@eukrea.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Note that the hardware schematics and documentations can be obtained
here: http://www.bugcommunity.com/wiki/index.php/BUGbase
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is to fix the warning below.
arch/arm/configs/mx51_defconfig:113:warning: symbol value 'm' invalid for LEDS_CLASS
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most fix is for uart txd/cts. They don't need to select input.
And fix some other pads with wrong select input.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch declares regulators for the efikamx. Use it also to power off the
efikamx.
Unfortunately, on the efikamx to2 boards, this doesn't work but they allow to
power off by setting GPIO 4 13 to high level instead of powering off through
the mc13892.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that usb has been fixed, we can enable usb h1 on efikamx
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Genesi EFIKA MX and EFIKA Smartbook are sharing a lot of things
so it makes sense to create a common file for both devices and a specific
file for each. No functionnal change except dropping uart 1 & 2.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i.MX23 Reference Manaul starts auart index from 1 than 0. Changing
the index to start from 0 requires corresponding changes on base
address, irq, and iomux definitions, and will probably confuse people
who reads codes and hardware documents together.
This patch introduced the field 'hwid' to distinguish the driver id
and controller id. These two ids are different on mx23 while
identical on mx28.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i.MX23 Reference Manual names auart irq differently from i.MX28.
This patch is to align the naming with mx28, so that some device
registration codes can be shared.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Do not include linux/device.h twice in drivers/tty/serial/mxs-auart.c .
Once is enough.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
