Report output values as 1/1000 of earth gravity.
Output values from lis3 can be read from sysfs position entry and from
input device. Input device can be accessed as event device and as
joystick device. Joystick device can be in two modes. Meaning of the
output values varies from case to case depending on the chip type and
configuration (scale). Only joystick interface in JS_CORR_BROKEN mode
returned somehow similar output values in different configurations.
Joystick device is in that state by default in case of lis3.
Position sysfs entry, input event device and raw joystick device have been
little bit broken since meaning of the output values has been varied
between 12 and 8 bit devices. Applications which relayed on those methods
failed if the chip is different than the expected one.
This patch converts output values to mean similar thing in different
configurations. Both 8 and 12 bit devices reports now same acceleration
values. If somebody implements full scale support to the driver, output
values will still mean the same. Scaling factor and input device range
must be updated in that case.
Joystick interface in JS_CORR_BROKEN mode is not touched by this patch.
All other interfaces have different scale after this change. For 12 bit
device scaling factor is 0.977 which keeps scaled and unscaled values are
quite close to each others. For 8 bit device, scaled values are 18 times
bigger than unscaled values.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is possible to read position information at the chip measurement rate
via sysfs. This patch adds possibility to configure chip measurement
rate.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chip is calibrated by the manufacturer. There is no need to calibarate it
at driver level. If the chip is used as a joystick, calibaration can be
done using joystick device calibration mechanism.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement selftest feature as specified by chip manufacturer. Control:
read selftest sysfs entry
Response: "OK x y z" or "FAIL x y z"
where x, y, and z are difference between selftest mode and normal mode.
Test is passed when values are within acceptance limit values.
Acceptance limits are provided via platform data. See chip spesifications
for acceptance limits. If limits are not properly set, OK / FAIL decision
is meaningless. However, userspace application can still make decision
based on the numeric x, y, z values.
Selftest is meant for HW diagnostic purposes. It is not meant to be
called during normal use of the chip. It may cause false interrupt
events. Selftest mode delays polling of the normal results but it doesn't
cause wrong values. Chip must be in static state during selftest. Any
acceration during the test causes most probably failure.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lis3 accelerometer sensors have quite long power on delay (up to 125
ms). This patch adds necessary delay to power on sequence for currently
supported lis3 chips.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: Éric Piel <eric.piel@tremplin-utc.net>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Originally the driver was only targeted to 12bits sensors. When support
for 8bits sensors was added, some slight difference in the registers were
overlooked. This should fix it, both for initialization, and for
displaying the rate.
Reported-by: Kalhan Trisal <kalhan.trisal@intel.com>
Reported-by: Christoph Plattner <christoph.plattner@gmx.at>
Tested-by: Christoph Plattner <christoph.plattner@gmx.at>
Tested-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of the documentation and comments were written when the driver was
only supporting one type of chip, only via ACPI/HP. Update the info to
the much clearer understanding that we have now.
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Send input_sync after each measurement round. This helps userspace to
detect which reported values belongs to the same measurement.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: Éric Piel <eric.piel@tremplin-utc.net>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add control of fan minimum turn-on output levels, decoupling it from the
fan turn-off output level. Add control of rate of change of fan output
level. These in turn allow lower turn-off rotor speed and smoother
transitions for better thermal and acoustic control authority. Add
support for constant fan speed and proportional-response operations modes.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Hubbard <david.c.hubbard@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These macros simply declare an enum, so drivers might as well declare
it themselves. This puts an end to the arbitrary limit of 8 chip types
per i2c driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
This macro simply declares an enum, so drivers might as well declare
it themselves.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Struct i2c_client_address_data only contains one field at this point,
which makes its usefulness questionable. Get rid of it and pass simple
address lists around instead.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
The "kind" parameter always has value -1, and nobody is using it any
longer, so we can remove it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (41 commits)
hwmon: (adt7475) Add VID support for the ADT7476
hwmon: (adt7475) Add an entry in MAINTAINERS
hwmon: (adt7475) Add support for the ADT7476
hwmon: (adt7475) Voltage attenuators can be bypassed
hwmon: (adt7475) Print device information on probe
hwmon: (adt7475) Handle alternative pin functions
hwmon: (adt7475) Move sysfs files removal to a separate function
hwmon: (adt7475) Add support for the ADT7490
hwmon: (adt7475) Improve device detection
hwmon: (adt7475) Add missing static marker
hwmon: (adt7475) Rework voltage inputs handling
hwmon: (adt7475) Implement pwm_use_point2_pwm_at_crit
hwmon: (adt7475) New documentation
hwmon: (adt7475) Add support for the ADT7473
hwmon: (f71882fg) Add support for the f71889fg (version 2)
hwmon: (f71882fg) Fix sysfs file removal
hwmon: (f71882fg) Cleanup sysfs attr creation 2/2
hwmon: (f71882fg) Cleanup sysfs attr creation 1/2
hwmon: (thmc50) Stop using I2C_CLIENT_MODULE_PARM
hwmon: Add Freescale MC13783 ADC driver
...
The ADT7476 has 5 dedicated pins for VID input, and the +12V input can
optionally be used as a 6th VID pin. Add support for VID input.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the Analog Devices ADT7476 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 5 voltage inputs instead of 2, and VID input
pins.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
It is possible to bypass the voltage attenuators on the +2.5V, Vccp,
+5V and +12V voltage monitoring inputs. This is useful to connect
other voltage channels than the ones the monitoring chip was
originally designed for. When this feature is enabled, we must not
include the scaling factors in our computations.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Print the device name and revision at probe time, as well as a list of
all optional features which are available.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
The TACH4 pin can be used for other functions, so fan4 may not always
be available. Likewise, the PWM2 pin can be used for ALERT output, in
which case pwm2 is not available
For the ADT7490, the +2.5 Vin pin may also be used for other
functions, in which case in0 is not available.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Move sysfs files removal to a separate function. The code is common to
the device probing error path and the standard device removal path. As
it will grow with future driver development, this avoids code
duplication.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the Analog Devices ADT7490 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 6 voltage inputs instead of 2.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Check the value of register 0x3f as part of the device detection, to
make it more robust.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
adt7475_attr_group is used internally only and can thus be marked
static.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Rework the handling of voltage inputs to make it possible and easy to
support more inputs. This will be needed for the upcoming ADT7490
support.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Implement the non-standard pwm_use_point2_pwm_at_crit sysfs attribute
as the adt7473 driver did.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the ADT7473 to the adt7475 driver, and mark the
adt7473 driver for removal. The ADT7473 and ADT7475 chips are almost
the same chip and essentially compatible, so there's no point in
having separate drivers for them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
This adds support for the Fintek f71889fg to the f71882fg driver,
many thanks to Gerd v. Egidy for providing (remote) access to a
machine which such an ic.
Note that this bit of the patch:
- val = SENSORS_LIMIT(val, 0, 255);
+
+ if (data->type == f71889fg)
+ val = SENSORS_LIMIT(val, -128, 127);
+ else
+ val = SENSORS_LIMIT(val, 0, 127);
Changes behaviour for already supported models, the new behaviour is correct
as the already supported models have bit 7 of the involved registers fixed at
0, so the previous behaviour which allowed setting temp zone limits > 127
was not correct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There is a bug in the old sysfs file removal, as it uses fxxxx_in_temp_attr
to remove the in and temp sysfs attributes, but fxxxx_in_temp_attr has
temp#_alarm, where as f71858fg_in_temp_attr has temp#_max_alarm, so
the temp#_max_alarm attributes for the f71858fg never get removed.
This patch fixes this by doing the sysfs removal exactly the same way as
the creation instead of being (too) clever, this will also avoid similar
bugs in the future.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch merges the f71882fg_auto_pwm_attr array into the
fxxxx_fan_attr resp. fxxxx_auto_pwm_attr array, as the f71882fg_auto_pwm_attr
array was merely extending these 2 with entries for a 4th fan, it also makes
these 2 arrays 2 dimensional so that the rest of the code can choose to
add attr for 3 or 4 fans without needing to know the nr of attr per fan.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch makes a number of cleanups to the sysfs attr creation
in the f71882fg driver, this is a preparation patch for adding f71889fg
support:
* Add some comments to explain why some models need separate sysfs attr
arrays for in / temp / fan / pwm
* Rename a number of sysfs attr arrays to make their function clearer
* Move the pwm#_auto_channels_temp attribute from the common to all
models fan attr array to the per model auto mode pwm attr arrays, so
that all the auto mode pwm attr are grouped together, and thus can be
left out on models where we don't support auto pwm mode
* Put fan_beep attr in their own array, so that only auto mode pwm attr
remain in the per model pwm sysfs attr arrays.
* Put the 4th special fan input for the f8000 in its own array, so that only
auto mode pwm attr remain in the per model pwm sysfs attr arrays.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The thmc50 driver is the last user of I2C_CLIENT_MODULE_PARM, and I
would like to get rid of that macro.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Krzysztof Helt <krzysztof.h1@wp.pl>
This driver provides support for the ADC integrated into the
Freescale MC13783 PMIC.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The w83791d driver has been in the kernel for a while now,
time to remove the EXPERIMENTAL dependency.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As kind is now hard-coded to -1, there is room for code clean-ups.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Riku Voipio <riku.voipio@iki.fi>
Acked-by: "Hans J. Koch" <hjk@linutronix.de>
Cc: Rudolf Marek <r.marek@assembler.cz>
As kind is now hard-coded to -1, there is room for code clean-ups.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Marc Hulsman <m.hulsman@tudelft.nl>
As kind is now hard-coded to -1, there is room for code clean-ups.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Andre Prendel <andre.prendel@gmx.de>
The National Semiconductor LM73 is a single temperature sensor, much
like the famous LM75.
Signed-off-by: Adrien Demarez <adrien.demarez@bolloretelecom.eu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Stop using global variables REG and VAL for I/O port numbers. This is
ugly and unsafe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rodolfo Giometti <giometti@linux.it>
This module parameter is there to workaround broken BIOS. I'm not even
sure if it was used in the past 5 years, and it gets in the way of
converting the driver to the MFD infrastructure. So tell the users how
they can do the same from user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rodolfo Giometti <giometti@linux.it>
