Explicitly set GRU instructions to "ACTIVE". This eliminates the need for
barriers that would have been necessary to prevent reading the instruction
"status" field before the GRU had actually started the instruction.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the GRU irq allocate/free functions to use the latest upstream
infrastructure.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix several bugs related to prefetch, ordering & speculation:
- GRU cch_allocate() instruction causes cacheable memory
to be created. Add a barriers to prevent speculation
from prefetching data before it exists.
- Add memory barriers before cache-flush instructions to ensure
that previously stored data is included in the line flushed to memory.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug caused by failure to allocate a GRU gts structure. The old code
failed to handle the case where the vma was invalid.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve existing driver self-tests. Add a new debugging test to the SGI
GRU driver for verifying the global GRU copy function.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a debug option to the SGI GRU driver for flushing GRU cache lines from
memory. In theory this is not needed but it is useful for debugging.
This has no use by end users.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Under some conditions, mmu_notifier_register() will fail to register a
mmu_notifier. Fix the GRU driver to correctly handle these failures.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Increase the maximum address supported by the SGI GRU driver to a full 64
bits. Note that GRU addresses are not always the same as socket virtual
addresses. Sockets may not necessarily support the full 64 bits.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve error messages for malfunctioning GRUs. Identify the type of
instruction that is failing.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug in module unload. Previous code was not correctly deleting the
files in /proc.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch builds on the infrastructure introduced in the patches that
allow user specification of GRU blades & chiplets for context allocation.
This patch simplifies the algorithms for migrating GRU contexts between
blades.
No new functionality is introduced.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support to the GRU driver to allow users to specify the blade &
chiplet for allocation of GRU contexts. Add new statistics for context
loading/unloading/retargeting. Also deleted a few GRU stats that were no
longer being unused.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add table & user request infrastructure that is needed to allow users to
specify the blade and chiplet for allocation of GRU contexts. Use of this
information is in a subsequent patch.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not use alloc_pages_exact_node() to allocate GRU tables. If a blade
has no local memory, nid will be -1. Use alloc_pages_node() instead.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
TLB dropins require updates to the CBR instruction istatus field. This is
needed to resolve race conditions in the chip.
The code currently uses the user address of the CBR. This works but opens
up additional endcases related to stealing of contexts and accessing the
CBR from tasks that do not have access to the user address space. (Some
of this non-user task access is debug code that is not currently being
pushed to the community).
User CBRs are also directly accessible using the kernel mapping of the
CBR. Change the TLB dropin code to use the the kernel mapping of the CBR.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add comments from previous code reviews. The comments help explain some
of the more esoteric aspects of the driver.
Move a free() to the other side of an unlock.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the GRU initialization code to initialize based on blade topology
instead of node topology. The result is the same but blade-based
initialization is cleaner.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, the UV xpc code is passing nid to the gru_create_message_queue
instead of nasid as it expects.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was a difficult bug to trip. XPC was in the middle of sending an
acknowledgement for a received message.
In xpc_received_payload_uv():
.
ret = xpc_send_gru_msg(ch->sn.uv.cached_notify_gru_mq_desc, msg,
sizeof(struct xpc_notify_mq_msghdr_uv));
if (ret != xpSuccess)
XPC_DEACTIVATE_PARTITION(&xpc_partitions[ch->partid], ret);
msg->hdr.msg_slot_number += ch->remote_nentries;
at the point in xpc_send_gru_msg() where the hardware has dispatched the
acknowledgement, the remote side is able to reuse the message structure
and send a message with a different slot number. This problem is made
worse by interrupts.
The adjustment of msg_slot_number and the BUG_ON in
xpc_handle_notify_mq_msg_uv() which verifies the msg_slot_number is
consistent are only used for debug purposes. Since a fix for this that
preserves the debug functionality would either have to infringe upon the
payload or allocate another structure just for debug, I decided to remove
it entirely.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many times while the initial connection is being made, the contacted
partition will send back both the ACTIVATING and the ACTIVE
remote_act_state changes in very close succescion. The 1/4 second delay
in the make first contact loop is large enough to nearly always miss the
ACTIVATING state change.
Since either state indicates the remote partition has acknowledged our
state change, accept either.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Under heavy load conditions, our set of xpc messages may become exhausted.
The code handles this correctly with the exception of the management code
which hits a NULL pointer dereference.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The UV BIOS has moved the location of some of their pointers to the
"partition reserved page" from memory into a uv hub MMR. The GRU does not
support bcopy operations from MMR space so we need to special case the MMR
addresses using VLOAD operations.
Additionally, the BIOS call for registering a message queue watchlist has
removed the 'blade' value and eliminated the structure that was being
passed in. This is also reflected in this patch.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The BIOS has decided to store a pointer to the partition reserved page in
a scratch MMR. The GRU is only able to read an MMR using a vload
instruction. The gru_read_gpa() function will implemented.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide an SGI SN2/UV agnositic method for converting a global physical
address into a socket physical address.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for 6 ranks per channel to the i5100 chipset. I have tested
the patch as far as possible with correctible errors and things appear
good. The DIMM mapping is correct for our board, but boards may differ.
Signed-off-by: Nils Carlson <nils.carlson@ludd.ltu.se>
Acked-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Addscrubbing to the i5100 chipset. The i5100 chipset only supports one
scrubbing rate, which is not constant but dependent on memory load. The
rate returned by this driver is an estimate based on some experimentation,
but is substantially closer to the truth than the speed supplied in the
documentation.
Also, scrubbing is done once, and then a done-bit is set. This means that
to accomplish continuous scrubbing a re-enabling mechanism must be used.
I have created the simplest possible such mechanism in the form of a
work-queue which will check every five minutes. This interval is quite
arbitrary but should be sufficient for all sizes of system memory.
Signed-off-by: Nils Carlson <nils.carlson@ludd.ltu.se>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i5100 driver uses the word controller instead of channel in a lot of
places, this is simply a cleanup of the patch.
Signed-off-by: Nils Carlson <nils.carlson@ludd.ltu.se>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KCS_IDLE and KCS_IDLE state have the same value, but in this function the
constants ending in _STATE are compared to the state variable.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Core Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert code away from ->read_proc/->write_proc interfaces. Switch to
proc_create()/proc_create_data() which make addition of proc entries
reliable wrt NULL ->proc_fops, NULL ->data and so on.
Problem with ->read_proc et al is described here commit
786d7e1612 "Fix rmmod/read/write races in
/proc entries"
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Adam Belay <abelay@mit.edu>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The intelfb driver sets color map depending on currently active pipe.
However, if an LVDS display is attached (like in laptop) the active pipe
variable is never set. The default value is PIPE_A and can be wrong. Set
up the pipe variable during driver initialization after hardware state was
read.
Also, the detection of the active display (and hence the pipe) is wrong.
The pipes are assigned to so called planes. Both pipes are always enabled
on my laptop but only one plane is enabled (the plane A for the CRT or the
plane B for the LVDS). Change active pipe detection code to take into
account a status of the plane assigned to each pipe.
The problem is visible in the 8 bpp mode if colors above 15 are used. The
first 16 color entries are displayed correctly.
The graphics chip description is here (G45 vol. 3):
http://intellinuxgraphics.org/documentation.html
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13285
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Michal Suchanek <hramrach@centrum.cz>
Cc: Dean Menezes <samanddeanus@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A humble attempt to simplify the coding style to improve readability
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Regression caused in 2.6.23 and then despite repeated requests never fixed
or dealt with (Petr promised to sort it in 2008 but seems to have
forgotten).
Enough is enough - remove the problem line that was added. If it upsets
someone they've had two years to deal with it and at the very least it'll
rattle their cage and wake them up.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=9709
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Damon <account@bugzilla.kernel.org.juxtaposition.net>
Tested-by: Ruud van Melick <rvm1974@raketnet.nl>
Cc: Petr Vandrovec <VANDROVE@vc.cvut.cz>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Paul A. Clarke <pc@us.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement frame buffer blank operation feature for DA8xx/OMAP-L1xx driver.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suspend/resume support DA8xx/OMAP-L1xx frame buffer driver. This feature
has been tested on DA850/OMAP-L138 EVM. For the purpose of testing, the
patch series[1] which adds suspend support for DA850/OMAP-L138 SoC was
applied.
[1] http://patchwork.kernel.org/patch/60260/
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a helper function to enable raster. Also add one member in the
private data structure to track the current blank status, another function
pointer which takes in the platform specific callback function to control
panel power.
These updates will help in adding suspend/resume and frame buffer blank
operation features.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed a typo: missing *. This would lead to a kernel oops if the kernel
was compiled without support for the /proc file system.
Found with a static checker. Compile tested.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch provides the acceleration entry points for the SM501
framebuffer driver.
This patch provides the sync, copyarea and fillrect entry points, using
the SM501's 2D acceleration engine to perform the operations in-chip
rather than across the bus.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the old style use of <asm/io.h> by replacing it with <linux/io.h>.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Cc: Vincent Sanders <vince@simtec.co.uk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are several places in the SM501 fb driver that could do with using
resource_size() to calculate the size of a resource.
Also fix a bug where request_mem_region() is being passed one too few
bytes when requesting the register memory region, which was causing the
following in /proc/iomem:
13e80000-13e8ffff : sm501-fb.0
13e80000-13e8fffe : sm501-fb
fixed, this reads:
13e80000-13e8ffff : sm501-fb.0
13e80000-13e8ffff : sm501-fb
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Cc: Vincent Sanders <vince@simtec.co.uk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox has found that the i810fb function "uses a whopping 2.5K of stack".
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reported-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The GRUB folks requested copyright/license info for lxfb.h, so here it is.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add cpufreq support for DA8xx/OMAP-L1xx frame buffer driver
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clock divider value can be calculated from the pixel clock value for
the panel. This gives more flexiblity to the driver to change the divider
value on the fly as in the case of cpufreq feature- support for which will
be added shortly.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Steve Chen <schen@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the NULL test on fbi is needed, then the dereference should be after the
NULL test.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add check if palette register number is in correct range for few drivers
which miss it. The regno value comes indirectly from user space.
Two drivers has converted check from BUG_ON() macro to just return an
error (non-zero value).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kernel has simple_strtol() implementation which could be used as atoi().
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
