* Use CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS instead of
CONFIG_IDE_ARCH_OBSOLETE_INIT in init_ide_data().
* Remove no longer needed CONFIG_IDE_ARCH_OBSOLETE_INIT.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS to drivers/ide/Kconfig and use
it instead of defining IDE_ARCH_OBSOLETE_DEFAULTS in <arch/ide.h>.
v2:
* Define ide_default_irq() in ide-probe.c/ns87415.c if not already defined
and drop defining ide_default_irq() for CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS=n.
[ Thanks to Stephen Rothwell and David Miller for noticing the problem. ]
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
IDE PMAC host driver and all IDE PCI host drivers use pci_enable_device()
nowadays so the following quirk in pmac_pcibios_after_init() can be removed.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add special cases for pplus and prep to ide_default_{irq,io_base}()
(+ FIXMEs about the need to use IDE platform host driver instead).
* Remove no longer needed ppc_ide_md and struct ide_machdep_calls.
* Then remove <linux/ide.h> include from:
- arch/powerpc/kernel/setup_32.c
- arch/ppc/kernel/ppc_ksyms.c
- arch/ppc/kernel/setup.c
- arch/ppc/platforms/pplus.c
- arch/ppc/platforms/prep_setup.c
There should be no functional changes caused by this patch.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Call ide_init_default_irq() for pplus in init_ide_data().
* Remove no longer needed pplus_ide_init_hwif_ports().
There should be no functional changes caused by this patch.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_FORCE_LEGACY_IRQS host flag for Motorola-Sandpoint platform
to sl82c105 host driver.
* Disable ide_generic host driver in arch/ppc/configs/sandpoint_defconfig
and enable sl82c105 one.
* Remove ppc_ide_md hooks from arch/ppc/platforms/sandpoint.c - no need for
them (sl82c105 host driver takes care of all this setup).
* Then remove no longer needed <linux/ide.h> include.
* Also update arch/ppc/platforms/sandpoint.h.
Unfortunately (unlike lopec's case) sl82c105 host driver was not enabled
in defconfing so there is a funcionality change.
[ Not a big deal since sl82c105 is superior over ide_generic. ]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_FORCE_LEGACY_IRQS host flag for Motorola-LoPEC platform
to sl82c105 host driver.
* Remove ppc_ide_md hooks from arch/ppc/platforms/lopec.c - no need for
them (sl82c105 host driver takes care of all this setup).
* Then remove no longer needed <linux/ide.h> include.
Looking at arch/ppc/configs/lopec_defconfig:
...
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_IDEPCI_SHARE_IRQ is not set
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_SL82C105=y
...
there should be no functional changes unless somebody preferred to disable
sl82c105 host driver and use only ide_generic one (but why would anybody
want to do such thing :-).
PS It seems that lopec_defconfig hasn't been updated for ages but if somebody
is going to do it please look into disabling IDE_GENERIC and BLK_DEV_GENERIC
config options. Thanks.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Initialize IDE ports in mpc8xx_ide_probe().
* Remove m8xx_ide_init() and ppc_ide_md hooks - no need for them
(IDE mpc8xx host driver takes care of all this setup).
* Remove needless 'if (irq)' and 'if (data_port >= MAX_HWIFS)' checks
from m8xx_ide_init_hwif_ports().
* Remove 'ctrl_port' and 'irq' arguments from m8xx_ide_init_hwif_ports().
* Rename m8xx_ide_init_hwif_ports() to m8xx_ide_init_ports().
* Add __init tag to m8xx_ide_init_ports().
This patch fixes hwif->irq always being overriden to 0 (== auto-probe, is
this even working on PPC?) because of ide_init_default_irq() call in ide.c.
There should be no other functional changes.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add pmac_ide_init_ports() helper and use it instead of
pmac_ide_init_hwif_ports().
* Remove ppc_ide_md hooks - no need for them
(IDE pmac host driver takes care of all this setup).
* Then remove no longer needed <linux/ide.h> include
from arch/powerpc/platforms/powermac/pmac.h.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There are no "default" IDE ports on PPC4xx so ppc4xx_ide_init_hwif_ports() is
unnecessary, remove it. Also remove no longer needed <linux/ide.h> include.
There should be no functional changes caused by this patch.
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also remove now not needed <linux/ide.h> include.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove unused pmac_ide_{check_base,get_irq}() and pmac_find_ide_boot(),
then remove no longer needed ide_majors[] and pmac_ide_count.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
mv idefloppy_do_end_request -> idefloppy_end_request as is the case with ide-cd
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This new struct unifies ide{-floppy,-tape,-scsi}'s view of a packet command. For now,
it represents the common denominator between the three drivers while adding driver-
specific members at the end of the struct which will be merged/simplified into the
generic ATAPI handling code in later steps, or removed completely.
Bart:
- move struct ide_atapi_pc outside of #ifdef/#endif CONFIG_IDE_PROC_FS
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Removing the atomic tests for pc's is unobjectionable. Since this driver will
probably go to /dev/null soon, the atomic tests for tape->flags are left in
place for there are some situations where they're needed (chrdev DSC handling,
low level pipeline operation and so on). While at it, rename all test/set flag
bit defines explicitly to *_FLAG_* for clarity.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bart:
- no need to move defines for tape flags around
(they are completely rewritten by the next patch)
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_{ALTSTATUS,IREASON,BCOUNTL,BCOUNTH}_OFFSET defines.
* Remove IDE_*_REG macros - this results in more readable
and slightly smaller code.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_atapi_{discard_data,write_zeros} inline helpers to <linux/ide.h>
and use them instead of home-brewn helpers in ide-{floppy,tape,scsi}.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
scc_pata has the different BAR configuration and using ide_setup_pci_device()
is inappropriate.
(ide_setup_pci_device() expects a normal PCI IDE controller with
BAR0..BAR3 either non-existant or being primary/secondary port bases
in I/O space.)
This patch do all needed setup itself instead of calling ide_setup_pci_device().
[bart: minor checkpatch.pl fixes]
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
hdparm explicitely marks HDIO_[UNREGISTER,SCAN]_HWIF ioctls as DANGEROUS
and given the number of bugs we can assume that there are no real users:
* DMA has no chance of working because DMA resources are released by
ide_unregister() and they are never allocated again.
* Since ide_init_hwif_ports() is used for ->io_ports[] setup the ioctls
don't work for almost all hosts with "non-standard" (== non ISA-like)
layout of IDE taskfile registers (there is a lot of such host drivers).
* ide_port_init_devices() is not called when probing IDE devices so:
- drive->autotune is never set and IDE host/devices are not programmed
for the correct PIO/DMA transfer modes (=> possible data corruption)
- host specific I/O 32-bit and IRQ unmasking settings are not applied
(=> possible data corruption)
- host specific ->port_init_devs method is not called (=> no luck with
ht6560b, qd65xx and opti621 host drivers)
* ->rw_disk method is not preserved (=> no HPT3xxN chipsets support).
* ->serialized flag is not preserved (=> possible data corruption when
using icside, aec62xx (ATP850UF chipset), cmd640, cs5530, hpt366
(HPT3xxN chipsets), rz1000, sc1200, dtc2278 and ht6560b host drivers).
* ->ack_intr method is not preserved (=> needed by ide-cris, buddha,
gayle and macide host drivers).
* ->sata_scr[] and sata_misc[] is cleared by ide_unregister() and it
isn't initialized again (SiI3112 support needs them).
* To issue an ioctl() there need to be at least one IDE device present
in the system.
* ->cable_detect method is not preserved + it is not called when probing
IDE devices so cable detection is broken (however since DMA support is
also broken it doesn't really matter ;-).
* Some objects which may have already been freed in ide_unregister()
are restored by ide_hwif_restore() (i.e. ->hwgroup).
* ide_register_hw() may unregister unrelated IDE ports if free ide_hwifs[]
slot cannot be found.
* When IDE host drivers are modular unregistered port may be re-used by
different host driver that owned it first causing subtle bugs.
Since we now have a proper warm-plug support remove these ioctls,
then remove no longer needed:
- ide_register_hw() and ide_hwif_restore() functions
- 'init_default' and 'restore' arguments of ide_unregister()
- zeroeing of hwif->{dma,extra}_* fields in ide_unregister()
As an added bonus IDE core code size shrinks by ~3kB (x86-32).
v2:
* fix ide_unregister() arguments in cleanup_module() (Andrew Morton).
v3:
* fix ide_unregister() arguments in palm_bk3710.c.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove CONFIG_BLK_DEV_HD hack from init_hwif_default()
("hda=noprobe hdb=noprobe" kernel parameters should be used
instead if somebody wishes to use the old "hd" driver).
* Make CONFIG_BLK_DEV_HD_ONLY config option available also when
IDE subsystem is used and update help entry.
* Remove no longer needed CONFIG_BLK_DEV_HD_IDE config option.
v2:
* Update documentation to suggest "hda=noprobe hdb=noprobe"
instead of obsoleted "ide0=noprobe".
* Update Documentation/ide/ide.txt.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
request_irq() will fail if there is already another IRQ handler
registered and IRQ flags are mismatched.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_generic_sysfs_init() helper registering 'ide_generic' class
(together with ide_generic_class_release() ->class_release method)
and use it in ide_generic_init().
* Add "add" class attribute to 'ide_generic' class for adding new interfaces
(it is intended to be a replacement for obsoleted "idex=base[,ctl[,irq]]"
kernel parameters).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'struct class ide_port_class' ('ide_port' class) and a 'struct
device *portdev' ('ide_port' class device) in ide_hwif_t.
* Register 'ide_port' class in ide_init() and unregister it in
cleanup_module().
* Create ->portdev in ide_register_port () and unregister it in
ide_unregister().
* Add "delete_devices" class device attribute for unregistering IDE devices
on a port and "scan" one for probing+registering IDE devices on a port.
* Add ide_sysfs_register_port() helper for registering "delete_devices"
and "scan" attributes with ->portdev. Call it in ide_device_add_all().
* Document IDE warm-plug support in Documentation/ide/warm-plug-howto.txt.
v2:
* Convert patch from using 'struct class_device' to use 'struct device'.
(thanks to Kay Sievers for doing it)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
->busproc method is used by HDIO_SET_BUSSTATE ioctl but it has no chance
of working as intended (in 2.4.x days) because to issue an ioctl there
is a device node needed and:
- for BUSSTATE_TRISTATE+OFF it is too late (devices are already gone)
- for BUSSTATE_TRISTATE+ON it is too early (devices are not registered yet)
Just remove ->busproc method for now (it was only implemented by hpt366,
siimage and tc86c001 host drivers).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Rework PowerMac media-bay support in such way that instead of
un/registering the IDE interface we un/register IDE devices:
* Add ide_port_scan() helper for probing+registerering devices on a port.
* Rename ide_port_unregister_devices() to __ide_port_unregister_devices().
* Add ide_port_unregister_devices() helper for unregistering devices on a port.
* Add 'ide_hwif_t *cd_port' to 'struct media_bay_info', pass 'hwif' instead
of hwif->index to media_bay_set_ide_infos() and use it to setup 'cd_port'.
* Use ide_port_unregister_devices() instead of ide_unregister()
and ide_port_scan() instead of ide_register_hw() in media_bay_step().
* Unexport ide_register_hw() and make it static.
v2:
* Fix build by adding <linux/ide.h> include to <asm-powerpc/mediabay.h>.
(Reported by Michael/Kamalesh/Andrew).
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_cfg_mtx lock/unlock to ide_port_setup_devices() and then move
ide_port_setup_devices() call from init_irq() to ide_device_add_all().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out devices init from ide_init_port_data() to
ide_port_init_devices_data().
While at it:
* Add explicit clearing of IDE device structure.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out code unregistering devices from ide_unregister() to
ide_port_unregister_devices().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
IDE devices need to be removed from /proc/ide/ _before_ being unregistered:
* Drop 'ide_hwif_t *hwif' argument from destroy_proc_ide_device()
and use drive->hwif instead.
* Rename destroy_proc_ide_device() to ide_proc_unregister_device().
* Call ide_proc_unregister_device() in drive_release_dev().
* Remove no longer needed destroy_proc_ide_drives().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out cable detection from ide_init_port() to ide_port_cable_detect().
* Move ide_port_cable_detect() call to ide_device_add_all().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ide_find_port() instead of ide_deprecated_find_port() in bast-ide/
palm_bk3710/ide-cs/delkin_cb host drivers and in ide_register_hw().
* Remove no longer needed ide_deprecated_find_port().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Instead of checking for '->io_ports[IDE_DATA_OFFSET] == 0' check for
'->chipset == ide_unknown' when looking for an empty ide_hwifs[] slot.
* Do ide-pnp initialization after ide-generic when IDE is built-in
(ide-pnp is the only user of ide_find_port() which needs such fixup).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This hwif->chipset fixup is already present in ide_device_add_all()
but for warm-plug support we also need to reserve not currently present
interfaces.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This option is obsolete and can be removed safely.
It allows us to remove the pci_get_device_reverse() function from the
PCI core.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
'ack' is currently a simple integer that flags whether or not a client is done
touching fields in the given descriptor. It is effectively just a single bit
of information. Converting this to a flags parameter allows the other bits to
be put to use to control completion actions, like dma-unmap, and capture
results, like xor-zero-sum == 0.
Changes are one of:
1/ convert all open-coded ->ack manipulations to use async_tx_ack
and async_tx_test_ack.
2/ set the ack bit at prep time where possible
3/ make drivers store the flags at prep time
4/ add flags to the device_prep_dma_interrupt prototype
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
DMA drivers no longer need to be notified of dependency submission
events as async_tx_run_dependencies and async_tx_channel_switch will
handle the scheduling and execution of dependent operations.
[sfr@canb.auug.org.au: extend this for fsldma]
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
