Since commit 363d0e5628 ("media: pwm-ir-tx: Trigger edges from
hrtimer interrupt context"), pwm-ir-tx uses high resolution timers
for IR signal generation when the pwm can be used from atomic context.
Ensure they are available.
Fixes: 363d0e5628 ("media: pwm-ir-tx: Trigger edges from hrtimer interrupt context")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When irtoy_command fails, buf should be freed since it is allocated by
irtoy_tx, or there is a memleak.
Fixes: 4114978dcd ("media: ir_toy: prevent device from hanging during transmit")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Note that bpf attach/detach also requires CAP_NET_ADMIN.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver requests the interrupts as IRQF_SHARED, so the interrupt
handlers can be called at any time. If such a call happens while the ISP
is powered down, the SoC will hang as the driver tries to access the
ISP registers.
This can be reproduced even without the platform sharing the IRQ line:
Enable CONFIG_DEBUG_SHIRQ and unload the driver, and the board will
hang.
Fix this by adding a new field, 'irqs_enabled', which is used to bail
out from the interrupt handler when the ISP is not operational.
Link: https://lore.kernel.org/r/20231218-rkisp-shirq-fix-v1-2-173007628248@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This reverts commit 85d2a31fe4.
The rkisp1 does share interrupt lines on some platforms, after all. Thus
we need to revert this, and implement a fix for the rkisp1 shared irq
handling in a follow-up patch.
Closes: https://lore.kernel.org/all/87o7eo8vym.fsf@gmail.com/
Link: https://lore.kernel.org/r/20231218-rkisp-shirq-fix-v1-1-173007628248@ideasonboard.com
Reported-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Several functions implementing VIDIOC_REQBUFS and _CREATE_BUFS all use
almost the same code to fill in the flags and capability fields. Refactor
this into a new vb2_set_flags_and_caps() function that replaces the old
fill_buf_caps() and validate_memory_flags() functions.
This also fixes a bug where vb2_ioctl_create_bufs() would not set the
V4L2_BUF_CAP_SUPPORTS_MAX_NUM_BUFFERS cap and also not fill in the
max_num_buffers field.
Fixes: d055a76c00 ("media: core: Report the maximum possible number of buffers for the queue")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Use vb2_get_num_buffers() to avoid using queue num_buffers field directly.
This allows us to change how the number of buffers is computed in the
future.
Fixes: d055a76c00 ("media: core: Report the maximum possible number of buffers for the queue")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Change compatible string to match dt bindings for TI devices. K3 family
prefix should not be included as it deviates from naming convention.
Fixes: 9707a6254a ("media: chips-media: wave5: Add the v4l2 layer")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/all/CAMuHMdUYOq=q1j=d+Eac28hthOUAaNUkuvxmRu-mUN1pLKq69g@mail.gmail.com/
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This patch replaces max(a, min(b, c)) by clamp(b, a, c) in the solo6x10
driver. This improves the readability and more importantly, for the
solo6x10-p2m.c file, this reduces on my system (x86-64, gcc 13):
- the preprocessed size from 121 MiB to 4.5 MiB;
- the build CPU time from 46.8 s to 1.6 s;
- the build memory from 2786 MiB to 98MiB.
In fine, this allows this relatively simple C file to be built on a
32-bit system.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Closes: https://lore.kernel.org/lkml/18c6df0d-45ed-450c-9eda-95160a2bbb8e@gmail.com/
Cc: <stable@vger.kernel.org> # v6.7+
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: David Laight <David.Laight@ACULAB.COM>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(controllers set the flag, but there is no client to use it). Also,
CLASS_SPD support gets simplified to prepare removal in the future.
Class based instantiation is not recommended these days anyhow.
Furthermore, I2C core now creates a debugfs directory per I2C adapter.
Current bus driver users were converted to use it. Then, there are also
quite some driver updates. Standing out are patches for the wmt-driver
which is refactored to support more variants. This is the rebased pull
request where a large series for the designware driver was dropped.
-----BEGIN PGP SIGNATURE-----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=8D3Q
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"This removes the currently unused CLASS_DDC support (controllers set
the flag, but there is no client to use it).
Also, CLASS_SPD support gets simplified to prepare removal in the
future. Class based instantiation is not recommended these days
anyhow.
Furthermore, I2C core now creates a debugfs directory per I2C adapter.
Current bus driver users were converted to use it.
Finally, quite some driver updates. Standing out are patches for the
wmt-driver which is refactored to support more variants.
This is the rebased pull request where a large series for the
designware driver was dropped"
* tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
MAINTAINERS: use proper email for my I2C work
i2c: stm32f7: add support for stm32mp25 soc
i2c: stm32f7: perform I2C_ISR read once at beginning of event isr
dt-bindings: i2c: document st,stm32mp25-i2c compatible
i2c: stm32f7: simplify status messages in case of errors
i2c: stm32f7: perform most of irq job in threaded handler
i2c: stm32f7: use dev_err_probe upon calls of devm_request_irq
i2c: i801: Add lis3lv02d for Dell XPS 15 7590
i2c: i801: Add lis3lv02d for Dell Precision 3540
i2c: wmt: Reduce redundant: REG_CR setting
i2c: wmt: Reduce redundant: function parameter
i2c: wmt: Reduce redundant: clock mode setting
i2c: wmt: Reduce redundant: wait event complete
i2c: wmt: Reduce redundant: bus busy check
i2c: mux: reg: Remove class-based device auto-detection support
i2c: make i2c_bus_type const
dt-bindings: at24: add ROHM BR24G04
eeprom: at24: use of_match_ptr()
i2c: cpm: Remove linux,i2c-index conversion from be32
i2c: imx: Make SDA actually optional for bus recovering
...
After removal of the legacy eeprom driver the only remaining I2C
client device driver supporting I2C_CLASS_SPD is jc42. Because this
driver also supports I2C_CLASS_HWMON, adapters don't have to
declare support for I2C_CLASS_SPD if they support I2C_CLASS_HWMON.
It's one step towards getting rid of I2C_CLASS_SPD mid-term.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This contains a bunch of cleanups and simplifications across the board,
as well as a number of small fixes.
Perhaps the most notable change here is the addition of an API that
allows PWMs to be used in atomic contexts, which is useful when time-
critical operations are involved, such as using a PWM to generate IR
signals.
Finally, I have decided to step down as PWM subsystem maintainer. Due to
other responsibilities I have lately not been able to find the time that
the subsystem deserves and Uwe, who has been helping out a lot for the
past few years and has many things planned for the future, has kindly
volunteered to take over. I have no doubt that he will be a suitable
replacement.
-----BEGIN PGP SIGNATURE-----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=pIh8
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This contains a bunch of cleanups and simplifications across the
board, as well as a number of small fixes.
Perhaps the most notable change here is the addition of an API that
allows PWMs to be used in atomic contexts, which is useful when time-
critical operations are involved, such as using a PWM to generate IR
signals.
Finally, I have decided to step down as PWM subsystem maintainer. Due
to other responsibilities I have lately not been able to find the time
that the subsystem deserves and Uwe, who has been helping out a lot
for the past few years and has many things planned for the future, has
kindly volunteered to take over. I have no doubt that he will be a
suitable replacement"
* tag 'pwm/for-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
MAINTAINERS: pwm: Thierry steps down, Uwe takes over
pwm: linux/pwm.h: fix Excess kernel-doc description warning
pwm: Add pwm_apply_state() compatibility stub
pwm: cros-ec: Drop documentation for dropped struct member
pwm: Drop two unused API functions
pwm: lpc18xx-sct: Don't modify the cached period of other PWM outputs
pwm: meson: Simplify using dev_err_probe()
pwm: stmpe: Silence duplicate error messages
pwm: Reduce number of pointer dereferences in pwm_device_request()
pwm: crc: Use consistent variable naming for driver data
pwm: omap-dmtimer: Drop locking
dt-bindings: pwm: ti,pwm-omap-dmtimer: Update binding for yaml
media: pwm-ir-tx: Trigger edges from hrtimer interrupt context
pwm: bcm2835: Allow PWM driver to be used in atomic context
pwm: Make it possible to apply PWM changes in atomic context
pwm: renesas: Remove unused include
pwm: Replace ENOTSUPP with EOPNOTSUPP
pwm: Rename pwm_apply_state() to pwm_apply_might_sleep()
pwm: Stop referencing pwm->chip
pwm: Update kernel doc for struct pwm_chip
...
-----BEGIN PGP SIGNATURE-----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=KPPn
-----END PGP SIGNATURE-----
Merge tag 'media/v6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- v4l core: subdev frame interval now supports which field
- v4l kapi: moves and renames the init_cfg pad op to init_state as an
internal op.
- new sensor drivers: gc0308, gc2145, Avnet Alvium, ov64a40, tw9900
- new camera driver: STM32 DCMIPP
- s5p-mfc has gained MFC v12 support
- new ISP driver added to staging: Starfive
- new stateful encoder/decoded: Wave5 codec It is found on the J721S2
SoC, JH7100 SoC, ssd202d SoC. Etc.
- fwnode gained support for MIPI "DisCo for Imaging"
(https://www.mipi.org/specifications/mipi-disco-imaging)
- as usual, lots of cleanups, fixups and driver improvements.
* tag 'media/v6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (309 commits)
media: i2c: thp7312: select CONFIG_FW_LOADER
media: i2c: mt9m114: use fsleep() in place of udelay()
media: videobuf2: core: Rename min_buffers_needed field in vb2_queue
media: i2c: thp7312: Store frame interval in subdev state
media: docs: uAPI: Fix documentation of 'which' field for routing ioctls
media: docs: uAPI: Expand error documentation for invalid 'which' value
media: docs: uAPI: Clarify error documentation for invalid 'which' value
media: v4l2-subdev: Store frame interval in subdev state
media: v4l2-subdev: Add which field to struct v4l2_subdev_frame_interval
media: v4l2-subdev: Turn .[gs]_frame_interval into pad operations
media: v4l: subdev: Move out subdev state lock macros outside CONFIG_MEDIA_CONTROLLER
media: s5p-mfc: DPB Count Independent of VIDIOC_REQBUF
media: s5p-mfc: Load firmware for each run in MFCv12.
media: s5p-mfc: Set context for valid case before calling try_run
media: s5p-mfc: Add support for DMABUF for encoder
media: s5p-mfc: Add support for UHD encoding.
media: s5p-mfc: Add support for rate controls in MFCv12
media: s5p-mfc: Add YV12 and I420 multiplanar format support
media: s5p-mfc: Add initial support for MFCv12
media: s5p-mfc: Rename IS_MFCV10 macro
...
new drivers:
- imagination - new driver for Imagination Technologies GPU
- xe - new driver for Intel GPUs using core drm concepts
core:
- add CLOSE_FB ioctl
- remove old UMS ioctls
- increase max objects to accomodate AMD color mgmt
encoder:
- create per-encoder debugfs directory
edid:
- split out drm_eld
- SAD helpers
- drop edid_firmware module parameter
format-helper:
- cache format conversion buffers
sched:
- move from kthread to workqueue
- rename some internals
- implement dynamic job-flow control
gpuvm:
- provide more features to handle GEM objects
client:
- don't acquire module reference
displayport:
- add mst path property documentation
fdinfo:
- alignment fix
dma-buf:
- add fence timestamp helper
- add fence deadline support
bridge:
- transparent aux-bridge for DP/USB-C
- lt8912b: add suspend/resume support and power regulator support
panel:
- edp: AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49
- chromebook panel support
- elida-kd35t133: rework pm
- powkiddy RK2023 panel
- himax-hx8394: drop prepare/unprepare and shutdown logic
- BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G
- Evervision VGG644804, SDC ATNA45AF01
- nv3052c: register docs, init sequence fixes, fascontek FS035VG158
- st7701: Anbernic RG-ARC support
- r63353 panel controller
- Ilitek ILI9805 panel controller
- AUO G156HAN04.0
simplefb:
- support memory regions
- support power domains
amdgpu:
- add new 64-bit sequence number infrastructure
- add AMD specific color management
- ACPI WBRF support for RF interference handling
- GPUVM updates
- RAS updates
- DCN 3.5 updates
- Rework PCIe link speed handling
- Document GPU reset types
- DMUB fixes
- eDP fixes
- NBIO 7.9/7.11 updates
- SubVP updates
- XGMI PCIe state dumping for aqua vanjaram
- GFX11 golden register updates
- enable tunnelling on high pri compute
amdkfd:
- Migrate TLB flushing logic to amdgpu
- Trap handler fixes
- Fix restore workers handling on suspend/resume
- Fix possible memory leak in pqm_uninit()
- support import/export of dma-bufs using GEM handles
radeon:
- fix possible overflows in command buffer checking
- check for errors in ring_lock
i915:
- reorg display code for reuse in xe driver
- fdinfo memory stats printing
- DP MST bandwidth mgmt improvements
- DP panel replay enabling
- MTL C20 phy state verification
- MTL DP DSC fractional bpp support
- Audio fastset support
- use dma_fence interfaces instead of i915_sw_fence
- Separate gem and display code
- AUX register macro refactoring
- Separate display module/device parameters
- Move display capabilities debugfs under display
- Makefile cleanups
- Register cleanups
- Move display lock inits under display/
- VLV/CHV DPIO PHY register and interface refactoring
- DSI VBT sequence refactoring
- C10/C20 PHY PLL hardware readout
- DPLL code cleanups
- Cleanup PXP plane protection checks
- Improve display debug msgs
- PSR selective fetch fixes/improvements
- DP MST fixes
- Xe2LPD FBC restrictions removed
- DGFX uses direct VBT pin mapping
- more MTL WAs
- fix MTL eDP bug
- eliminate use of kmap_atomic
habanalabs:
- sysfs entry to identify a device minor id with debugfs path
- sysfs entry to expose device module id
- add signed device info retrieval through INFO ioctl
- add Gaudi2C device support
- pcie reset prepare/done hooks
msm:
- Add support for SDM670, SM8650
- Handle the CFG interconnect to fix the obscure hangs / timeouts
- Kconfig fix for QMP dependency
- use managed allocators
- DPU: SDM670, SM8650 support
- DPU: Enable SmartDMA on SM8350 and SM8450
- DP: enable runtime PM support
- GPU: add metadata UAPI
- GPU: move devcoredumps to GPU device
- GPU: convert to drm_exec
ivpu:
- update FW API
- new debugfs file
- a new NOP job submission test mode
- improve suspend/resume
- PM improvements
- MMU PT optimizations
- firmware profile frequency support
- support for uncached buffers
- switch to gem shmem helpers
- replace kthread with threaded irqs
rockchip:
- rk3066_hdmi: convert to atomic
- vop2: support nv20 and nv30
- rk3588 support
mediatek:
- use devm_platform_ioremap_resource
- stop using iommu_present
- MT8188 VDOSYS1 display support
panfrost:
- PM improvements
- improve interrupt handling as poweroff
qaic:
- allow to run with single MSI
- support host/device time sync
- switch to persistent DRM devices
exynos:
- fix potential error pointer dereference
- fix wrong error checking
- add missing call to drm_atomic_helper_shutdown
omapdrm:
- dma-fence lockdep annotation fix
tidss:
- dma-fence lockdep annotation fix
- support for AM62A7
v3d:
- BCM2712 - rpi5 support
- fdinfo + gputop support
- uapi for CPU job handling
virtio-gpu:
- add context debug name
-----BEGIN PGP SIGNATURE-----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=nuw0
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2024-01-10' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This contains two major new drivers:
- imagination is a first driver for Imagination Technologies devices,
it only covers very specific devices, but there is hope to grow it
- xe is a reboot of the i915 GPU (shares display) side using a more
upstream focused development model, and trying to maximise code
sharing. It's not enabled for any hw by default, and will hopefully
get switched on for Intel's Lunarlake.
This also drops a bunch of the old UMS ioctls. It's been dead long
enough.
amdgpu has a bunch of new color management code that is being used in
the Steam Deck.
amdgpu also has a new ACPI WBRF interaction to help avoid radio
interference.
Otherwise it's the usual lots of changes in lots of places.
Detailed summary:
new drivers:
- imagination - new driver for Imagination Technologies GPU
- xe - new driver for Intel GPUs using core drm concepts
core:
- add CLOSE_FB ioctl
- remove old UMS ioctls
- increase max objects to accomodate AMD color mgmt
encoder:
- create per-encoder debugfs directory
edid:
- split out drm_eld
- SAD helpers
- drop edid_firmware module parameter
format-helper:
- cache format conversion buffers
sched:
- move from kthread to workqueue
- rename some internals
- implement dynamic job-flow control
gpuvm:
- provide more features to handle GEM objects
client:
- don't acquire module reference
displayport:
- add mst path property documentation
fdinfo:
- alignment fix
dma-buf:
- add fence timestamp helper
- add fence deadline support
bridge:
- transparent aux-bridge for DP/USB-C
- lt8912b: add suspend/resume support and power regulator support
panel:
- edp: AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49
- chromebook panel support
- elida-kd35t133: rework pm
- powkiddy RK2023 panel
- himax-hx8394: drop prepare/unprepare and shutdown logic
- BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G
- Evervision VGG644804, SDC ATNA45AF01
- nv3052c: register docs, init sequence fixes, fascontek FS035VG158
- st7701: Anbernic RG-ARC support
- r63353 panel controller
- Ilitek ILI9805 panel controller
- AUO G156HAN04.0
simplefb:
- support memory regions
- support power domains
amdgpu:
- add new 64-bit sequence number infrastructure
- add AMD specific color management
- ACPI WBRF support for RF interference handling
- GPUVM updates
- RAS updates
- DCN 3.5 updates
- Rework PCIe link speed handling
- Document GPU reset types
- DMUB fixes
- eDP fixes
- NBIO 7.9/7.11 updates
- SubVP updates
- XGMI PCIe state dumping for aqua vanjaram
- GFX11 golden register updates
- enable tunnelling on high pri compute
amdkfd:
- Migrate TLB flushing logic to amdgpu
- Trap handler fixes
- Fix restore workers handling on suspend/resume
- Fix possible memory leak in pqm_uninit()
- support import/export of dma-bufs using GEM handles
radeon:
- fix possible overflows in command buffer checking
- check for errors in ring_lock
i915:
- reorg display code for reuse in xe driver
- fdinfo memory stats printing
- DP MST bandwidth mgmt improvements
- DP panel replay enabling
- MTL C20 phy state verification
- MTL DP DSC fractional bpp support
- Audio fastset support
- use dma_fence interfaces instead of i915_sw_fence
- Separate gem and display code
- AUX register macro refactoring
- Separate display module/device parameters
- Move display capabilities debugfs under display
- Makefile cleanups
- Register cleanups
- Move display lock inits under display/
- VLV/CHV DPIO PHY register and interface refactoring
- DSI VBT sequence refactoring
- C10/C20 PHY PLL hardware readout
- DPLL code cleanups
- Cleanup PXP plane protection checks
- Improve display debug msgs
- PSR selective fetch fixes/improvements
- DP MST fixes
- Xe2LPD FBC restrictions removed
- DGFX uses direct VBT pin mapping
- more MTL WAs
- fix MTL eDP bug
- eliminate use of kmap_atomic
habanalabs:
- sysfs entry to identify a device minor id with debugfs path
- sysfs entry to expose device module id
- add signed device info retrieval through INFO ioctl
- add Gaudi2C device support
- pcie reset prepare/done hooks
msm:
- Add support for SDM670, SM8650
- Handle the CFG interconnect to fix the obscure hangs / timeouts
- Kconfig fix for QMP dependency
- use managed allocators
- DPU: SDM670, SM8650 support
- DPU: Enable SmartDMA on SM8350 and SM8450
- DP: enable runtime PM support
- GPU: add metadata UAPI
- GPU: move devcoredumps to GPU device
- GPU: convert to drm_exec
ivpu:
- update FW API
- new debugfs file
- a new NOP job submission test mode
- improve suspend/resume
- PM improvements
- MMU PT optimizations
- firmware profile frequency support
- support for uncached buffers
- switch to gem shmem helpers
- replace kthread with threaded irqs
rockchip:
- rk3066_hdmi: convert to atomic
- vop2: support nv20 and nv30
- rk3588 support
mediatek:
- use devm_platform_ioremap_resource
- stop using iommu_present
- MT8188 VDOSYS1 display support
panfrost:
- PM improvements
- improve interrupt handling as poweroff
qaic:
- allow to run with single MSI
- support host/device time sync
- switch to persistent DRM devices
exynos:
- fix potential error pointer dereference
- fix wrong error checking
- add missing call to drm_atomic_helper_shutdown
omapdrm:
- dma-fence lockdep annotation fix
tidss:
- dma-fence lockdep annotation fix
- support for AM62A7
v3d:
- BCM2712 - rpi5 support
- fdinfo + gputop support
- uapi for CPU job handling
virtio-gpu:
- add context debug name"
* tag 'drm-next-2024-01-10' of git://anongit.freedesktop.org/drm/drm: (2340 commits)
drm/amd/display: Allow z8/z10 from driver
drm/amd/display: fix bandwidth validation failure on DCN 2.1
drm/amdgpu: apply the RV2 system aperture fix to RN/CZN as well
drm/amd/display: Move fixpt_from_s3132 to amdgpu_dm
drm/amd/display: Fix recent checkpatch errors in amdgpu_dm
Revert "drm/amdkfd: Relocate TBA/TMA to opposite side of VM hole"
drm/amd/display: avoid stringop-overflow warnings for dp_decide_lane_settings()
drm/amd/display: Fix power_helpers.c codestyle
drm/amd/display: Fix hdcp_log.h codestyle
drm/amd/display: Fix hdcp2_execution.c codestyle
drm/amd/display: Fix hdcp_psp.h codestyle
drm/amd/display: Fix freesync.c codestyle
drm/amd/display: Fix hdcp_psp.c codestyle
drm/amd/display: Fix hdcp1_execution.c codestyle
drm/amd/pm/smu7: fix a memleak in smu7_hwmgr_backend_init
drm/amdkfd: Fix iterator used outside loop in 'kfd_add_peer_prop()'
drm/amdgpu: Drop 'fence' check in 'to_amdgpu_amdkfd_fence()'
drm/amdkfd: Confirm list is non-empty before utilizing list_first_entry in kfd_topology.c
drm/amdgpu: Fix '*fw' from request_firmware() not released in 'amdgpu_ucode_request()'
drm/amdgpu: Fix variable 'mca_funcs' dereferenced before NULL check in 'amdgpu_mca_smu_get_mca_entry()'
...
The recently added driver uses the firmware loader mechanism but causes
a link failure when that is in a loadable module while thp7312 itself
is built-in:
arm-linux-gnueabi-ld: drivers/media/i2c/thp7312.o: in function `thp7312_probe':
thp7312.c:(.text+0x4164): undefined reference to `firmware_upload_register'
Select the required Kconfig symbol. Note that the driver specifically
needs the firmware upload interface that is controlled by CONFIG_FW_UPLOAD,
but there is no link failure when that is disabled because the interfaces
are stubbed out here.
Link: https://lore.kernel.org/linux-media/20240103155811.4092035-1-arnd@kernel.org
Fixes: 7a52ab415b ("media: i2c: Add driver for THine THP7312")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This makes the generated IR much more precise. Before this change, the
driver is unreliable and many users opted to use gpio-ir-tx instead.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In order to introduce a pwm api which can be used from atomic context,
we will need two functions for applying pwm changes:
int pwm_apply_might_sleep(struct pwm *, struct pwm_state *);
int pwm_apply_atomic(struct pwm *, struct pwm_state *);
This commit just deals with renaming pwm_apply_state(), a following
commit will introduce the pwm_apply_atomic() function.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # for input
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
With clang-16, building without COMMON_CLK triggers a range check on
udelay() because of a constant division-by-zero calculation:
ld.lld: error: undefined symbol: __bad_udelay
>>> referenced by mt9m114.c
>>> drivers/media/i2c/mt9m114.o:(mt9m114_power_on) in archive vmlinux.a
In this configuration, the driver already fails to probe, before
this function gets called, so it's enough to suppress the assertion.
Do this by using fsleep(), which turns long delays into sleep() calls
in place of the link failure.
This is probably a good idea regardless to avoid overly long dynamic
udelay() calls on a slow clock.
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Fixes: 24d756e914 ("media: i2c: Add driver for onsemi MT9M114 camera sensor")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Rename min_buffers_needed into min_queued_buffers and update
the documentation about it.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: Drop the change where min_queued_buffers + 1 buffers would be]
[hverkuil: allocated. Now this patch only renames this field instead of making]
[hverkuil: a functional change as well.]
[hverkuil: Renamed 3 remaining min_buffers_needed occurrences.]
Use the newly added storage for frame interval in the subdev state to
simplify the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Subdev states store all standard pad configuration data, except for
frame intervals. Fix it by adding interval fields in the
v4l2_subdev_pad_config and v4l2_subdev_stream_config structures, with
corresponding accessor functions and a helper function to implement the
.get_frame_interval() operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Due to a historical mishap, the v4l2_subdev_frame_interval structure
is the only part of the V4L2 subdev userspace API that doesn't contain a
'which' field. This prevents trying frame intervals using the subdev
'TRY' state mechanism.
Adding a 'which' field is simple as the structure has 8 reserved fields.
This would however break userspace as the field is currently set to 0,
corresponding to V4L2_SUBDEV_FORMAT_TRY, while the corresponding ioctls
currently operate on the 'ACTIVE' state. We thus need to add a new
subdev client cap, V4L2_SUBDEV_CLIENT_CAP_INTERVAL_USES_WHICH, to
indicate that userspace is aware of this new field.
All drivers that implement the subdev .get_frame_interval() and
.set_frame_interval() operations are updated to return -EINVAL when
operating on the TRY state, preserving the current behaviour.
While at it, fix a bad copy&paste in the documentation of the struct
v4l2_subdev_frame_interval_enum 'which' field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-media
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for tegra-video
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The subdev .[gs]_frame_interval are video operations, but they operate
on pads (and even on streams). Not only is this confusing, it causes
practical issues for drivers as the operations don't receive a subdev
state pointer, requiring manual state handling.
To improve the situation, turn the operations into pad operations, and
extend them to receive a state pointer like other pad operations.
While at it, rename the operations to .[gs]et_frame_interval at the same
time to match the naming scheme of other pad operations. This isn't
strictly necessary, but given that all drivers using those operations
need to be modified, handling the rename separately would generate more
churn for very little gain (if at all).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-media
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for tegra-video
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add allocation of DPB buffers based on MFC requirement so,
codec buffers allocations has been moved after state
MFCINST_HEAD_PRODUCED. It is taken care that codec buffer allocation
is performed in process context from userspace IOCTL call.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In MFCv12, some section of firmware gets updated at each MFC run.
Hence we need to reload original firmware for each run at the start.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Context bit is set for hardware execution if there is a buffer in
source and destination queue before calling try_run in the
init_buffers function. Now there will be a new context created and
hardware will be invoked for the buffer queued instead of waiting for
another buffer to be queued from userspace to set this context bit for
hw execution.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
MFC driver had restriction on max resolution of 1080p, updated it for
UHD. Added corresponding support to set recommended profile and level
for H264 in UHD scenario.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In MFCv12, the rc configs are changed with support for CBR loose,
CBR tight and Variable Bitrate (VBR) added.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
YV12 and I420 format (3-plane) support is added. Stride information is
added to all formats and planes since it is necessary for YV12/I420
which are different from width.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add support for MFCv12, with a new register file and necessary hw
control, decoder, encoder and structural changes. Add luma dbp, chroma
dpb and mv sizes for each codec as per the UM for MFCv12, along with
appropriate alignment.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Renames macro IS_MFCV10 to IS_MFCV10_PLUS so that the MFCv10 code can
be resued for MFCv12 support. Since some part of MFCv10 specific code
holds good for MFCv12 also.
Cc: linux-fsd@tesla.com
Signed-off-by: Smitha T Murthy <smithatmurthy@gmail.com>
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a driver for the OmniVision OV64A40 image sensor.
Co-developed-by: Lee Jackson <lee.jackson@arducam.com>
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In addition to the existing 2592x1940 12-bit mode, introduce support
for 2592x1940 10-bit mode.
Following are the register set which control the 10/12 bit mode setting:
MDBIT 0x319d
ADBIT 0x3050
ADBIT1 0x341c
0x341d
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The V4L2_CID_HBLANK control is marked as readonly and can only be a
single value.
Set the minimum and maximum value to match the mode value.
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Support reporting of the Sensor Native and Active pixel array areas
through the Selection API.
The implementation reports a single target crop only for the mode that
is presently exposed by the driver.
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Provide support for enabling and disabling regulator supplies to control
power to the camera sensor.
While updating the power on function, document that a sleep is
represented as 'T4' in the datasheet power on sequence.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The existing imx335_parse_hw_config function has two paths
that can be taken without reporting to the user the reason
for failing to accept the hardware configuration.
Extend the error reporting paths to identify failures when
probing the device.
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The use of \n as a line ending throughout the driver is inconsistent.
While it is possible for logging messages to automatically have newlines
added by the kernel printk mechanisms, this is specifically to support
continued lines with PR_CONT and the lack of a new line character
indicates that the text is a fragment of a continuation line.
As each of these lines are whole and not fragments, explicitly define the
newline for consistency.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Set effective and active sensor pixel sizes as shown in product
brief[1].
[1]: https://www.mouser.com/datasheet/2/897/ProductBrief_IMX214_20150428-1289331.pdf
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Obtain rotation and orientation information from system firmware and
register the appropriate controls. While at it, update number of
pre-allocated control slots.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Code refinement.
While at it, don't destroy the mutex not initialized yet if the controls
are initialized incorrectly.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Code refinement, no functional changes.
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
[Sakari Ailus: The control handler remains in the context struct still.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Introduce new driver for GalaxyCore GC0308, which is a cheap
640x480 with an on-chip ISP sensor sold since 2010. Data is
provided via parallel bus.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
[Sakari Ailus: Changed MAINTAINERS to match GC2145 entry.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Graciously handle an uninitialised (but still zeroed) sub-device in
v4l2_subdev_cleanup(). The list_empty() check there is unnecessary, too,
so replace that by cheking whether the lists's next field is NULL.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The only known devices that use an ov2740 sensor in combination with
the ipu-bridge code are various Lenovo ThinkPad models, which all
need the link-frequency to be 180 MHz for things to work properly.
The ov2740 driver used to only support 360 MHz link-frequency,
which is why the ipu-bridge entry used 360 MHz, but now the
ov2740 driver has been extended to also support 180 MHz.
The ov2740 is actually used with 360 MHz link-frequency on Chromebooks.
On Chromebooks the camera/sensor fwnode graph is part of the ACPI tables.
The ipu-bridge code is used to dynamically generate the graph when it is
missing, so it is not used on Chromebooks and the ov2740 will keep using
360 MHz link-frequency there as before.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Split the resetting of the sensor out of the link_freq_config reg_list
and add a delay after this.
This hopefully fixes the stream sometimes not starting, this was
taken from the ov2740 sensor driver in the out of tree IPU6 driver:
https://github.com/intel/ipu6-drivers/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
On various Lenovo Thinkpad models with an ov2740 sensor the 360 MHz
link frequency is not supported.
Add support for 180 MHz link frequency, even though this has half the
pixel clock, this supports the same framerate by using half the VTS value
(significantly reducing the amount of empty lines send during vblank).
Normally if there are multiple link-frequencies then the sensor driver
choses the lowest link-frequency still usable for the chosen resolution.
In this case the board supports only 1 link-frequency. Which frequency
is supported is checked in ov2740_check_hwcfg() and then a different
set of supported_modes (using only the supported link-freq) is selected.
The register settings for this were taken from the ov2740 sensor driver
in the out of tree IPU6 driver:
https://github.com/intel/ipu6-drivers/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Alloc ov2740_data and set up the drvdata pointer before calling
ov2740_check_hwcfg().
This is a preparation patch to allow ov2740_check_hwcfg()
to store some of the parsed data in the ov2740 struct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
