When als_capture_sample() is called with usage ID
HID_USAGE_SENSOR_TIME_TIMESTAMP, return 0. The HID sensor core ignores
the return value for capture_sample() callback, so return value doesn't
make difference. But correct the return value to return success instead
of -EINVAL.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20240204125617.2635574-1-srinivas.pandruvada@linux.intel.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big set of char/misc and other driver subsystem changes for
6.8-rc1. Lots of stuff in here, but first off, you will get a merge
conflict in drivers/android/binder_alloc.c when merging this tree due to
changing coming in through the -mm tree.
The resolution of the merge issue can be found here:
https://lore.kernel.org/r/20231207134213.25631ae9@canb.auug.org.au
or in a simpler patch form in that thread:
https://lore.kernel.org/r/ZXHzooF07LfQQYiE@google.com
If there are issues with the merge of this file, please let me know.
Other than lots of binder driver changes (as you can see by the merge
conflicts) included in here are:
- lots of iio driver updates and additions
- spmi driver updates
- eeprom driver updates
- firmware driver updates
- ocxl driver updates
- mhi driver updates
- w1 driver updates
- nvmem driver updates
- coresight driver updates
- platform driver remove callback api changes
- tags.sh script updates
- bus_type constant marking cleanups
- lots of other small driver updates
All of these have been in linux-next for a while with no reported issues
(other than the binder merge conflict.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaeMMQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynWNgCfQ/Yz7QO6EMLDwHO5LRsb3YMhjL4AoNVdanjP
YoI7f1I4GBcC0GKNfK6s
=+Kyv
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem changes
for 6.8-rc1.
Other than lots of binder driver changes (as you can see by the merge
conflicts) included in here are:
- lots of iio driver updates and additions
- spmi driver updates
- eeprom driver updates
- firmware driver updates
- ocxl driver updates
- mhi driver updates
- w1 driver updates
- nvmem driver updates
- coresight driver updates
- platform driver remove callback api changes
- tags.sh script updates
- bus_type constant marking cleanups
- lots of other small driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (341 commits)
android: removed duplicate linux/errno
uio: Fix use-after-free in uio_open
drivers: soc: xilinx: add check for platform
firmware: xilinx: Export function to use in other module
scripts/tags.sh: remove find_sources
scripts/tags.sh: use -n to test archinclude
scripts/tags.sh: add local annotation
scripts/tags.sh: use more portable -path instead of -wholename
scripts/tags.sh: Update comment (addition of gtags)
firmware: zynqmp: Convert to platform remove callback returning void
firmware: turris-mox-rwtm: Convert to platform remove callback returning void
firmware: stratix10-svc: Convert to platform remove callback returning void
firmware: stratix10-rsu: Convert to platform remove callback returning void
firmware: raspberrypi: Convert to platform remove callback returning void
firmware: qemu_fw_cfg: Convert to platform remove callback returning void
firmware: mtk-adsp-ipc: Convert to platform remove callback returning void
firmware: imx-dsp: Convert to platform remove callback returning void
firmware: coreboot_table: Convert to platform remove callback returning void
firmware: arm_scpi: Convert to platform remove callback returning void
firmware: arm_scmi: Convert to platform remove callback returning void
...
This reverts commit 5f05285df6.
This commit assumes that every HID descriptor for ALS sensor has
presence of usage id ID HID_USAGE_SENSOR_LIGHT_COLOR_TEMPERATURE.
When the above usage id is absent, driver probe fails. This breaks
ALS sensor functionality on many platforms.
Till we have a good solution, revert this commit.
Reported-by: Thomas Weißschuh <thomas@t-8ch.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218223
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <stable@vger.kernel.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20231217200703.719876-3-srinivas.pandruvada@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ee3710f39f.
This commit assumes that every HID descriptor for ALS sensor has
presence of usage id ID HID_USAGE_SENSOR_LIGHT_CHROMATICITY_X and
HID_USAGE_SENSOR_LIGHT_CHROMATICITY_Y. When the above usage ids are
absent, driver probe fails. This breaks ALS sensor functionality on
many platforms.
Till we have a good solution, revert this commit.
Reported-by: Thomas Weißschuh <thomas@t-8ch.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218223
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <stable@vger.kernel.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20231217200703.719876-2-srinivas.pandruvada@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ISL76682 is very basic ALS which only supports ALS or IR mode
in four ranges, 1k/4k/16k/64k LUX. There is no IRQ support or any
other fancy functionality.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20231127212726.77707-2-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Vishay VEMl6075 is a low power, 16-bit resolution UVA and UVB
light sensor with I2C interface and noise compensation (visible and
infrarred).
Every UV channel generates an output signal measured in counts per
integration period, where the integration time is configurable.
This driver adds support for both UV channels and the ultraviolet
index (UVI) inferred from them according to the device application note
with open-air (no teflon) coefficients.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20231110-veml6075-v3-3-6ee46775b422@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For better precision of input light intesity, return floating point
values through sysfs instead of an integer value
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Link: https://lore.kernel.org/r/20231107192005.285534-1-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The RGB + IR data can be used to calculate the illuminance value (luxes).
Implement the equation obtained from the ROHM HW colleagues and add a
raw light data channel outputting illuminance values in (nano) Luxes.
Both the read_raw and buffering values are supported, with the limitation
that buffering is only allowed when a suitable scan-mask is used. (RGB+IR,
no clear).
The equation has been developed by ROHM HW colleagues for open air sensor.
Adding any lens to the sensor is likely to impact to used c1, c2, c3
coefficients. Also, the output values have only been tested on BU27008.
According to the HW colleagues, the very same equation should work on
BU27010 as well.
Calculate and output illuminance values from BU27008 and BU27010.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/ZTJcOxSb/WHzdN8h@dc78bmyyyyyyyyyyyyydt-3.rev.dnainternet.fi
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Particularly great to see a resolver driver move out of staging via a
massive set of changes. Only took 13 years :)
One small patch added then reverted due to a report of test breakage
(ashai-kasei,ak8975: Drop deprecated enums.)
An immutable branch was used for some hid-senors changes in case
there was a need to take them into the HID tree as well.
New device support
-----------------
adi,hmc425a
- Add support for HMC540SLP3E broadband 4-bit digital attenuator.
kionix,kx022a
- Add support for the kx132-1211 accelerometer. Require significant
driver rework to enable this including add a chip type specific
structure to deal with the chip differences.
- Add support for the kx132acr-lbz accelerometer (subset of the kx022a
feature set).
lltc,ltc2309
- New driver for this 8 channel ADC.
microchip,mcp3911
- Add support for rest of mcp391x family of ADCs (there are various
differences beyond simple channel count variation.
Series includes some general driver cleanup.
microchip,mcp3564
- New driver for MCP3461, MCP3462, MCP3464, MCP3541, MCP3562, MCP3564
and their R variants of 16/24bit ADCs. A few minor fixed followed.
rohm,bu1390
- New driver for this pressure sensor.
Staging graduation
------------------
adi,ad1210 (after 13 or so years :)
- More or less a complete (step-wise) rewrite of this resolver driver
to bring it up to date with modern IIO standards. The fault signal
handling mapping to event channels was particularly complex and
significant part of the changes.
Features
--------
iio-core
- Add chromacity and color temperature channel types.
adi,ad7192
- Oversampling ratio control (called fast settling in datasheet).
adi,adis16475
- Add core support and then driver support for delta angle and delta
velocity channels. These are intended for summation to establish
angle and velocity changes over larger timescales. Fix was
needed for alignment after the temperature channel. Further fix
reduced set of devices for which the buffer support was applicable
as seems burst reads don't cover these on all devices.
hid-sensors-als
- Chromacity and color temperatures support including in amd sfh.
stx104
- Add support for counter subsystem to this multipurpose device.
ti,twl6030
- Add missing device tree binding description.
Clean up and minor fixes.
------------------------
treewide
- Drop some unused declarations across IIO.
- Make more use of device_get_match_data() instead of OF specific
approaches.
Similar cleanup to sets of drivers.
- Stop platform remove callbacks returning anything by using the
temporary remove_new() callback.
- Use i2c_get_match_data() to cope nicely with all types of ID table
entry.
- Use device_get_match_data() for various platform device to cope
with more types of firmware.
- Convert from enum to pointer in ID tables allowing use of
i2c_get_match_data().
- Fix sorting on some ID tables.
- Include specific string helper headers rather than simply string_helpers.h
docs
- Better description of the ordering requirements etc for
available_scan_masks.
tools
- Handle alignment of mixed sizes where the last element isn't the biggest
correctly. Seems that doesn't happen often!
adi,ad2s1210
- Lots of work from David Lechner on this driver including a few fixes
that are going with the rework to avoid slowing that down.
adi,ad4310
- Replace deprecated devm_clk_register()
adi,ad74413r
- Bring the channel function setting inline with the datasheet.
adi,ad7192
- Change to FIELD_PREP(), FIELD_GET().
- Calculate f_order from the sinc filter and chop filter states.
- Move more per chip config into data in struct ad7192_chip_info
- Cleanup unused parameter in channel macros.
adi,adf4350
- Make use of devm_* to simplify error handling for many of the setup
calls in probe() / tear down in remove() and error paths. Some more
work to be done on this one.
- Use dev_err_probe() for errors in probe() callback.
adi,adf4413
- Typo in function name prefix.
adi,adxl345
- Add channel scale to the chip type specific structure and drop
using a type field previously used for indirection.
asahi,ak8985
- Fix a mismatch introduced when switching from enum->pointers
in the match tables.
amlogic,meson
- Expand error logging during probe.
invensense,mpu6050
- Support level-shifter control. Whilst no one is sure exactly what this
is doing it is needed for some old boards.
- Document mount-matrix dt-binding.
mediatek,mt6577
- Use devm_clk_get_enabled() to replace open coded version and move
everything over to being device managed. Drop now empty remove()
callback. Fix follows to put the drvdata back.
- Use dev_err_probe() for error reporting in probe() callback.
memsic,mxc4005
- Add of_match_table.
microchip,mcp4725
- Move various chip specific data from being looked up by chip ID to
data in the chip type specific structure.
silicon-labs,si7005
- Add of_match_table and entry in trivial-devices.yaml
st,lsm6dsx
- Add missing mount-matrix dt binding documentation.
st,spear
- Use devm_clk_get_enabled() and some other devm calls to move everything
over to being device managed. Drop now empty remove() callback.
- Use dev_err_probe() to better handled deferred probing and tidy up
error reporting in probe() callback.
st,stm32-adc
- Add a bit of additional checking in probe() to protect against a NULL
pointer (no known path to trigger it today).
- Replace deprecated strncpy()
ti,ads1015
- Allow for edge triggers.
- Document interrupt in dt-bindings.
-----BEGIN PGP SIGNATURE-----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=wth0
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.7a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: 1st set of new device support, features and cleanup for 6.7
Particularly great to see a resolver driver move out of staging via a
massive set of changes. Only took 13 years :)
One small patch added then reverted due to a report of test breakage
(ashai-kasei,ak8975: Drop deprecated enums.)
An immutable branch was used for some hid-senors changes in case
there was a need to take them into the HID tree as well.
New device support
-----------------
adi,hmc425a
- Add support for HMC540SLP3E broadband 4-bit digital attenuator.
kionix,kx022a
- Add support for the kx132-1211 accelerometer. Require significant
driver rework to enable this including add a chip type specific
structure to deal with the chip differences.
- Add support for the kx132acr-lbz accelerometer (subset of the kx022a
feature set).
lltc,ltc2309
- New driver for this 8 channel ADC.
microchip,mcp3911
- Add support for rest of mcp391x family of ADCs (there are various
differences beyond simple channel count variation.
Series includes some general driver cleanup.
microchip,mcp3564
- New driver for MCP3461, MCP3462, MCP3464, MCP3541, MCP3562, MCP3564
and their R variants of 16/24bit ADCs. A few minor fixed followed.
rohm,bu1390
- New driver for this pressure sensor.
Staging graduation
------------------
adi,ad1210 (after 13 or so years :)
- More or less a complete (step-wise) rewrite of this resolver driver
to bring it up to date with modern IIO standards. The fault signal
handling mapping to event channels was particularly complex and
significant part of the changes.
Features
--------
iio-core
- Add chromacity and color temperature channel types.
adi,ad7192
- Oversampling ratio control (called fast settling in datasheet).
adi,adis16475
- Add core support and then driver support for delta angle and delta
velocity channels. These are intended for summation to establish
angle and velocity changes over larger timescales. Fix was
needed for alignment after the temperature channel. Further fix
reduced set of devices for which the buffer support was applicable
as seems burst reads don't cover these on all devices.
hid-sensors-als
- Chromacity and color temperatures support including in amd sfh.
stx104
- Add support for counter subsystem to this multipurpose device.
ti,twl6030
- Add missing device tree binding description.
Clean up and minor fixes.
------------------------
treewide
- Drop some unused declarations across IIO.
- Make more use of device_get_match_data() instead of OF specific
approaches.
Similar cleanup to sets of drivers.
- Stop platform remove callbacks returning anything by using the
temporary remove_new() callback.
- Use i2c_get_match_data() to cope nicely with all types of ID table
entry.
- Use device_get_match_data() for various platform device to cope
with more types of firmware.
- Convert from enum to pointer in ID tables allowing use of
i2c_get_match_data().
- Fix sorting on some ID tables.
- Include specific string helper headers rather than simply string_helpers.h
docs
- Better description of the ordering requirements etc for
available_scan_masks.
tools
- Handle alignment of mixed sizes where the last element isn't the biggest
correctly. Seems that doesn't happen often!
adi,ad2s1210
- Lots of work from David Lechner on this driver including a few fixes
that are going with the rework to avoid slowing that down.
adi,ad4310
- Replace deprecated devm_clk_register()
adi,ad74413r
- Bring the channel function setting inline with the datasheet.
adi,ad7192
- Change to FIELD_PREP(), FIELD_GET().
- Calculate f_order from the sinc filter and chop filter states.
- Move more per chip config into data in struct ad7192_chip_info
- Cleanup unused parameter in channel macros.
adi,adf4350
- Make use of devm_* to simplify error handling for many of the setup
calls in probe() / tear down in remove() and error paths. Some more
work to be done on this one.
- Use dev_err_probe() for errors in probe() callback.
adi,adf4413
- Typo in function name prefix.
adi,adxl345
- Add channel scale to the chip type specific structure and drop
using a type field previously used for indirection.
asahi,ak8985
- Fix a mismatch introduced when switching from enum->pointers
in the match tables.
amlogic,meson
- Expand error logging during probe.
invensense,mpu6050
- Support level-shifter control. Whilst no one is sure exactly what this
is doing it is needed for some old boards.
- Document mount-matrix dt-binding.
mediatek,mt6577
- Use devm_clk_get_enabled() to replace open coded version and move
everything over to being device managed. Drop now empty remove()
callback. Fix follows to put the drvdata back.
- Use dev_err_probe() for error reporting in probe() callback.
memsic,mxc4005
- Add of_match_table.
microchip,mcp4725
- Move various chip specific data from being looked up by chip ID to
data in the chip type specific structure.
silicon-labs,si7005
- Add of_match_table and entry in trivial-devices.yaml
st,lsm6dsx
- Add missing mount-matrix dt binding documentation.
st,spear
- Use devm_clk_get_enabled() and some other devm calls to move everything
over to being device managed. Drop now empty remove() callback.
- Use dev_err_probe() to better handled deferred probing and tidy up
error reporting in probe() callback.
st,stm32-adc
- Add a bit of additional checking in probe() to protect against a NULL
pointer (no known path to trigger it today).
- Replace deprecated strncpy()
ti,ads1015
- Allow for edge triggers.
- Document interrupt in dt-bindings.
* tag 'iio-for-6.7a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (201 commits)
iio: Use device_get_match_data()
iio: adc: MCP3564: fix warn: unsigned '__x' is never less than zero.
dt-bindings: trivial-devices: add silabs,si7005
iio: si7005: Add device tree support
drivers: imu: adis16475.c: Remove scan index from delta channels
dt-bindings: iio: imu: st,lsm6dsx: add mount-matrix property
iio: resolver: ad2s1210: remove of_match_ptr()
iio: resolver: ad2s1210: remove DRV_NAME macro
iio: resolver: ad2s1210: move out of staging
staging: iio: resolver: ad2s1210: simplify code with guard(mutex)
staging: iio: resolver: ad2s1210: clear faults after soft reset
staging: iio: resolver: ad2s1210: refactor sample toggle
staging: iio: resolver: ad2s1210: remove fault attribute
staging: iio: resolver: ad2s1210: add label attribute support
staging: iio: resolver: ad2s1210: add register/fault support summary
staging: iio: resolver: ad2s1210: implement fault events
iio: event: add optional event label support
staging: iio: resolver: ad2s1210: rename DOS reset min/max attrs
staging: iio: resolver: ad2s1210: convert DOS mismatch threshold to event attr
staging: iio: resolver: ad2s1210: convert DOS overrange threshold to event attr
...
After enabling/disabling interrupts on the vcnl4040 chip the als and/or
ps sensor is powered on or off depending on the interrupt enable bits.
This is made as a last step in write_event_config.
But there is no reason to do this as the runtime PM handles the power
state of the sensors. Interfering with this may impact sensor readings.
Consider the following:
1. Userspace makes sensor data reading which triggers RPM resume
(sensor powered on) and a RPM suspend timeout. The timeout is 2000ms
before RPM suspend powers the sensor off if no new reading is made
within the timeout period.
2. Userspace disables interrupts => powers sensor off
3. Userspace reads sensor data = 0 because sensor is off and the
suspend timeout has not passed. For each new reading made within the
timeout period the timeout is renewed with 2000ms and RPM will not
make a new resume (device was not suspended). So the sensor will
not be powered on.
4. No further userspace reading for 2000ms ends RPM suspend timeout and
triggers suspend (powers off already powered off sensor).
Powering sensor off in (2) makes all consecutive readings made within
2000ms to the previous reading (3) return invalid data.
Skip setting power state when writing new event config.
Fixes: 546676121c ("iio: light: vcnl4000: Add interrupt support for vcnl4040")
Fixes: bc292aaf9c ("iio: light: vcnl4000: add illuminance irq vcnl4040/4200")
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20230907-vcnl4000-pm-fix-v2-1-298e01f54db4@axis.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The deta angle and deta velocity channels were added in parallel with
color temperature and chromacity so this merge had to assign a
consistent order. I put the color related ones second.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In most cases, ambient color sensors also support the x and y light
colors, which represent the coordinates on the CIE 1931 chromaticity
diagram. Thus, add light chromaticity x and y.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230919081054.2050714-8-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In most cases, ambient color sensors also support light color temperature.
As a result, add support of light color temperature.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230919081054.2050714-4-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sensor hub attributes can be extended to support more channels. Repeat
the reading for the two existing channels and store them separately. It
still operates in the same manner as before where there was just one
entry. So in order to support more sensor hub attributes for ALS use
channel index to get specific sensor hub attributes.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230919081054.2050714-2-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-40-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-39-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-38-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-37-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace device_get_match_data()->i2c_get_match_data() to extend matching
support for ID table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Stefan Windfeldt-Prytz <stefan.windfeldt-prytz@axis.com>
Tested-by: Stefan Windfeldt-Prytz <stefan.windfeldt-prytz@axis.com>
Link: https://lore.kernel.org/r/20230812151908.188696-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BU27010 is an RGBC sensor with a flickering detection FIFO. The
RGBC+IR sensor functionality is largely similar to what the BU27008 has.
There are some notable things though:
- gain setting is once again new and exotic. Now, there is 6bit gain
setting where 4 of the bits are common to all channels and 2 bits
can be configured separately for each channel. The BU27010 has
similar "1X on other channels vs 2X on IR when selector is 0x0"
gain design as BU27008 had. So, we use same gain setting policy for
BU27010 as we did for BU27008 - driver sets same gain selector for all
channels but shows the gains separately for all channels so users
can (at least in theory) detect this 1X vs 2X madness...
- BU27010 has suffled all the control register bitfields to new
addresses and bit positions while still keeping the register naming
same.
- Some more power/reset control is added.
- FIFO for "flickering detection" is added.
The control register suffling made this slightly nasty. Still, it is
easier for maintenance perspective to add the BU27010 support in BU27008
driver because - even though the bit positions/addresses were changed -
most of the driver structure can be re-used. Writing own driver for
BU27010 would mean plenty of duplicate code albeit a tad more clarity.
The flickering FIFO is not supported by the driver.
Add BU27010 RGBC+IR support to rohm-bu27008 driver.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/111cd217ccece1c1f16ab4287532dc4e1ddb8a3f.1690958450.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BU27010 RGB + flickering sensor is in many regards similar to
the BU27008. Prepare for adding support for BU27010 by allowing
chip-specific properties to be brought from the of_device_id data.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/d5994648033d5513993b8d72eb186ddda211b5ac.1690958450.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no need to call the dev_err() function directly to print a custom
message when handling an error from either the platform_get_irq() or
platform_get_irq_byname() functions as both are going to display an
appropriate error message in case of a failure.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20230727073912.4178659-1-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The calibration bias is setting the LED current to change the detection
distance. Add read/write attribute for proximity calibration bias and
read attribute for available values. This is supported for vcnl4040 and
vcnl4200.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-9-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the proximity multi pulse (PS_MPS) as oversampling_ratio.
Instead of one single pulse per every defined time frame, one can
program2, 4, or even 8 pulses. This leads to a longer IRED on-time
for each proximity measurement value, which also results in a higher
detection range.
Add read/write attribute for proximity oversampling-ratio and read
attribute for available oversampling-ratio.
This is supported for vcnl4040 and vcnl4200.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-8-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add read/write attribute for proximity and illuminance period. The
period is set in the interrupt persistence flags(PS_PERS and ALS_PERS).
An interrupt will not be asserted if the raw value is not over (or lower)
than the threshold for the set continued amount of measurements.
The time in seconds is calculated by the number of continued refreshes
multiplied with the integration time.
It will always pick the next lower possible value. The period changes,
if the integration time is changed.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-7-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to configure ambient light sensor interrupts and threshold
limits for vcnl4040 and vcnl4200. If an interrupt is detected an event
will be pushed to the event interface.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-6-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add illuminance integration time for vcnl4040 and vcnl4200.
Add read/write attribute for illuminance integration time and read
attribute for available integration times.
Set scale and sampling rate according to the integration time.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-5-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check IIO_PROXIMITY with switch case in order to make it easier
to add further types like light.
Add check for IIO_EV_INFO_VALUE for writing rising or falling events.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-4-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add ps_it attributes for vcnl4200 (similar to vcnl4040).
Add read/write attribute for proximity integration time.
Read attribute for available proximity integration times.
Change sampling rate depending on integration time.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-3-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add proximity interrupt support for vcnl4200 (similar to vcnl4040).
Add support to configure proximity sensor interrupts and threshold
limits. If an interrupt is detected an event will be pushed to the
event interface.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-2-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The intensity data from bu27008 is unsigned. The type of the scan data
was incorrectly marked as signed resulting large intensity values to be
interpreted as negative ones.
Fix the scan data type.
Fixes: 41ff93d14f ("iio: light: ROHM BU27008 color sensor")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/240a7ca5fc1b76da20d81f930d00f31a54b1fdf8.1686648422.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver is expecting accuracy of NANOs for intensity scale in
raw_write. The IIO core is however defaulting to MICROs. This leads the
raw-write of smallest scales to never succeed as correct selector(s) are
not found.
Fix this by implementing the .write_raw_get_fmt callback to use NANO
accuracy for writes of IIO_CHAN_INFO_SCALE.
Fixes: 41ff93d14f ("iio: light: ROHM BU27008 color sensor")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/e4778b74cde41431f77bc8dd88ec18605da0b400.1686648422.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver is expecting accuracy of NANOs for intensity scale in
raw_write. The IIO core is however defaulting to MICROs. This leads the
raw-write of smallest scales to never succeed as correct selector(s) are
not found.
Fix this by implementing the .write_raw_get_fmt callback to use NANO
accuracy for writes of IIO_CHAN_INFO_SCALE.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: e52afbd610 ("iio: light: ROHM BU27034 Ambient Light Sensor")
Link: https://lore.kernel.org/r/5369117315cf05b88cf0ccb87373fd77190f6ca2.1686648422.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New device support
- honeywell,mprls0025pa
* New driver and dt-bindings for this series of pressure sensors.
- invensense,mpu6050
* Add support for ICM 20600 IMU (ID, bindings and device data).
- melexis,mlx90614
* Add support for mlx90615 Infra Red Thermometer after driver cleanup
and refactoring to support the differences in this device.
- renesas,x9250
* New driver and bindings for this quad potentiometer.
- rockchip,saradc
* Add support for RK3588. Also included is a bunch of refactoring and
cleanup for that driver.
- rohm,bu27008
* New driver bindings etc for this 5 photodiode color sensor.
- st,lsm9ds0/st,st-sensors
* ID added for LSM303D accelerometer and magnetometer including ACPI binding.
- ti,opt4001
* New driver and bindings for this ambient light sensor.
Features
- core
* Introduce iio_validate_own_trigger() for cases where a driver can only
consumer a trigger it registered (detected via same parent device).
Use it in the kionix,kx022a driver and new rohm,by27008 driver.
- dynaimage,al3320a
* ACPI binding CALS0001 seen on Lenovo Yoga Table 2 devices.
- kionix,kx002a
* Enable asynchronous probe.
- rohm,bu27034
* Enable asynchronous probe.
- ti,tmp006
* Explicit support for DT including binding documentation.
Cleanups, minor fixes and misc improvements.
- treewide
* Switch I2C drivers from probe_new() back to probe() - part of the
long process of getting rid of a parameter from probe()
* Various whitespace and typo fixes not otherwise called out.
- core
* industrialio-buffer,Style cleanup.
* Add documentation to extend_name field of struct iio_chan_spec to
direct people using it towards the label infrastructure instead.
extend_name was a design mistake a long time back so directly people
away from it may be useful.
- adi,ad7606
* Add HAS_IOPORT dependency to prepare for some Kconfig changes.
- bosch,bma400
* Drop pointless print of ret in a dev_err_probe() message.
- invensense,icm42600
* Rework timestamp handling to reduce jitter.
- mediatek,mt7986-auxdac
* Add DT binding for this part.
- qcom,spmi-vadc
* Allow for 1/16th prescaling used on a few devices.
* Various changes to channel labeling and naming, including dropping
use of fwnode_name which generates odd channel names. Small ABI
change as a result, but not thought to be a problem for users of this
platform.
- st,lsm6dsx
* dt-binding: Use common schema for mount-matrix via a reference.
- st,stm32
* Add a debug print for when legacy channel config is used.
- ti,palmas-adc
* Drop unused i2c.h include.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAmSF83ARHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0Foi+NRAAi8E2NRkzxteTuiFRsAokm/8HbAc/9rDq
2Xyj8zT5B6jmqpbNKPtIbxxAxLV/JY+3HBIorvDNcOVfmOfshMpT31eaKpehxPJ3
A00WaJ6bi7CTp0h/7QOZnZ27yr3tuJ2jpCiGKWERmTZ60kn3S/5JRrXWbfKVccyU
DR1SrsiVSbtDhD9w6kA7HBRsL0EmTQOP/ARlUcO4SB5BOC7rj9akaN6Q6LYSafOa
BFfTd2suekRA94mB/ugm25xAWLsl4Rdr1iNkHyaGcXaMOJZ/zWXq14y1eLbqIJIc
am8Wu2zvo+umNzuG5DMi3gxP2B57Zhcieh6sJ5egdbxB4kh5z3jrsAFiw/MLTEME
4Tc7uHBPFuXDdb8saxtmV2FVbC43+31FgCLivD0BGHtv0DndP7i//KCdp2aztmHo
juyxRCw40xiul5Ihzh3NjukM0pb1inuhgblcEZVKOyaCjhur8NXoTEEcSqXczDVU
BLHBmhQY2cKwqKWt1hbLXDs9iGlJBg0+P+P0VBsvy7WWOlvc9Hw8SryYwyBRJMYH
LW/Wh85eIcyKaaGGEd+HQAyXwGSlrhycUSJzwdcc1IrK8TrIxn5k4BpQpeToQPjJ
wBRRDigeciIN0K7L09N4hg+qTxtpLwFY945meAS0N60o5hZM4P40hnzL8m/Co0pH
gx8SugY1NGk=
=0gJ9
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.5a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanup for the 6.5 cycle.
New device support
- honeywell,mprls0025pa
* New driver and dt-bindings for this series of pressure sensors.
- invensense,mpu6050
* Add support for ICM 20600 IMU (ID, bindings and device data).
- melexis,mlx90614
* Add support for mlx90615 Infra Red Thermometer after driver cleanup
and refactoring to support the differences in this device.
- renesas,x9250
* New driver and bindings for this quad potentiometer.
- rockchip,saradc
* Add support for RK3588. Also included is a bunch of refactoring and
cleanup for that driver.
- rohm,bu27008
* New driver bindings etc for this 5 photodiode color sensor.
- st,lsm9ds0/st,st-sensors
* ID added for LSM303D accelerometer and magnetometer including ACPI binding.
- ti,opt4001
* New driver and bindings for this ambient light sensor.
Features
- core
* Introduce iio_validate_own_trigger() for cases where a driver can only
consumer a trigger it registered (detected via same parent device).
Use it in the kionix,kx022a driver and new rohm,by27008 driver.
- dynaimage,al3320a
* ACPI binding CALS0001 seen on Lenovo Yoga Table 2 devices.
- kionix,kx002a
* Enable asynchronous probe.
- rohm,bu27034
* Enable asynchronous probe.
- ti,tmp006
* Explicit support for DT including binding documentation.
Cleanups, minor fixes and misc improvements.
- treewide
* Switch I2C drivers from probe_new() back to probe() - part of the
long process of getting rid of a parameter from probe()
* Various whitespace and typo fixes not otherwise called out.
- core
* industrialio-buffer,Style cleanup.
* Add documentation to extend_name field of struct iio_chan_spec to
direct people using it towards the label infrastructure instead.
extend_name was a design mistake a long time back so directly people
away from it may be useful.
- adi,ad7606
* Add HAS_IOPORT dependency to prepare for some Kconfig changes.
- bosch,bma400
* Drop pointless print of ret in a dev_err_probe() message.
- invensense,icm42600
* Rework timestamp handling to reduce jitter.
- mediatek,mt7986-auxdac
* Add DT binding for this part.
- qcom,spmi-vadc
* Allow for 1/16th prescaling used on a few devices.
* Various changes to channel labeling and naming, including dropping
use of fwnode_name which generates odd channel names. Small ABI
change as a result, but not thought to be a problem for users of this
platform.
- st,lsm6dsx
* dt-binding: Use common schema for mount-matrix via a reference.
- st,stm32
* Add a debug print for when legacy channel config is used.
- ti,palmas-adc
* Drop unused i2c.h include.
* tag 'iio-for-6.5a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (59 commits)
dt-bindings: iio: rockchip: Fix 'oneOf' condition failed warning
dt-bindings: iio: afe: voltage-divider: Spelling s/curcuit/circuit/
dt-bindings: iio: adc: Add rockchip,rk3588-saradc string
iio: adc: rockchip_saradc: Use dev_err_probe
iio: adc: rockchip_saradc: Match alignment with open parenthesis
iio: adc: rockchip_saradc: Use of_device_get_match_data
iio: adc: rockchip_saradc: Make use of devm_clk_get_enabled
iio: adc: rockchip_saradc: Add support for RK3588
iio: adc: rockchip_saradc: Add callback functions
iio: temperature: tmp006: Add OF device matching support
dt-bindings: iio: temperature: Add support for tmp006
staging: iio: Switch i2c drivers back to use .probe()
iio: amplifiers: ad8366 Fix whitespace issue
iio: imu: inv_icm42600: avoid frequent timestamp jitter
MAINTAINERS: Add ROHM BU27008
iio: light: ROHM BU27008 color sensor
iio: kx022a: Use new iio_validate_own_trigger()
iio: trigger: Add simple trigger_validation helper
dt-bindings: iio: light: ROHM BU27008
iio: mlx90614: Add MLX90615 support
...
The ROHM BU27008 is a sensor with 5 photodiodes (red, green, blue, clear
and IR) with four configurable channels. Red and green being always
available and two out of the rest three (blue, clear, IR) can be
selected to be simultaneously measured. Typical application is adjusting
LCD backlight of TVs, mobile phones and tablet PCs.
Add initial support for the ROHM BU27008 color sensor.
- raw_read() of RGB and clear channels
- triggered buffer w/ DRDY interrtupt
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/2594162f0e44148cffb1fb05f1d6edfde6bd11bc.1683541225.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230515205048.19561-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The reset bit must be always written to the hardware no matter what value
is in a cache or register. Ensure this by using regmap_write_bits()
instead of the regmap_update_bits(). Furthermore, the SWRESET bit may be
self-clearing, so mark the SYSTEM_CONTROL register volatile to guarantee
we do also read the right state - should we ever need to read it.
Finally, writing the SWRESET bit will restore the default register
values. This can cause register cache to be outdated if there are any
register values cached.
Rebuild register cache after SWRESET and use regmap_update_bits() when
performing the reset.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: e52afbd610 ("iio: light: ROHM BU27034 Ambient Light Sensor")
Link: https://lore.kernel.org/r/ZFjWhbfuN5XcKty+@fedora
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Devices which may take a while to initialize during probe and which have
no strong reason to probe synchronously can request asynchronous probing
as default probe strategy. This can speed-up start times on some
platforms.
The BU27034 gets probe delayed for at least two reasons. It enables the
supply regulator, (which is likely to have ramp-up delay if it was
disabled) and additionally it delays while the sensor itself is
initializing.
Changing to asynchronous probing may cause problems. Some of which are
discussed in:
https://lore.kernel.org/all/06db017f-e985-4434-8d1d-02ca2100cca0@sirena.org.uk/
Enabling async probing for the ROHM BU27034 should be fairly safe to try
though as there is no in-tree users for it yet. If the async probing
appears to be an issue we can switch easily back to synchronous (or
better yet, fix the actual problem).
Enable asynchronous probing for BU27034.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/e7088793e1868c77b1894b30cd026e8ed043ea7c.1683185765.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver uses the continuous mode of the chip and integration
time can be configured through sysfs.
The constants for calculating lux value differs between packaging
so it uses different compatible string for the two versions
"ti,opt4001-picostar" and "ti,opt4001-sot-5x3" since the device id
is the same.
Datasheet: https://www.ti.com/lit/gpn/opt4001
Signed-off-by: Stefan Windfeldt-Prytz <stefan.windfeldt-prytz@axis.com>
Link: https://lore.kernel.org/r/20230323-add-opt4001-driver-v3-2-62e121dab294@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This sensor can be found as CALS0001 on the Lenovo Yoga
Tablet 2 series.
Tested on a Lenovo Yoga Tablet 2 1051-F.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230420232631.68864-1-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bu27034 uses micro seconds for integration time configuration. This
is incorrect as the ABI mandates use of seconds.
Change BU27034 driver to use seconds for integration time.
Fixes: e52afbd610 ("iio: light: ROHM BU27034 Ambient Light Sensor")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/a05647669af22ba919c7c87dccb43975e3235a87.1681722914.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost breaks
even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp5Eg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynSXgCg0kSw3vUYwpsnhAsQkoPw1QVA23sAn2edRCMa
GEkPWjrROueCom7xbLMu
=eR+P
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc drivers updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost
breaks even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (196 commits)
mcb-lpc: Reallocate memory region to avoid memory overlapping
mcb-pci: Reallocate memory region to avoid memory overlapping
mcb: Return actual parsed size when reading chameleon table
kernel/configs: Drop Android config fragments
virt: acrn: Replace obsolete memalign() with posix_memalign()
spmi: Add a check for remove callback when removing a SPMI driver
spmi: fix W=1 kernel-doc warnings
spmi: mtk-pmif: Drop of_match_ptr for ID table
spmi: pmic-arb: Convert to platform remove callback returning void
spmi: mtk-pmif: Convert to platform remove callback returning void
spmi: hisi-spmi-controller: Convert to platform remove callback returning void
w1: gpio: remove unnecessary ENOMEM messages
w1: omap-hdq: remove unnecessary ENOMEM messages
w1: omap-hdq: add SPDX tag
w1: omap-hdq: allow compile testing
w1: matrox: remove unnecessary ENOMEM messages
w1: matrox: use inline over __inline__
w1: matrox: switch from asm to linux header
w1: ds2482: do not use assignment in if condition
w1: ds2482: drop unnecessary header
...
New device support
* bosch,bmp280
- Add support for BMP580 - includes significant refactoring and general
driver cleanup + support for non-volatile memory for trimming and config
parameters.
* rohm BU27034
- New driver for this 3 channel ambient light sensor.
- New support library for devices where both integration time and
amplifier gain are configurable. In these cases a scale change
may require changing bother underlying values. This library module
provides code to help with this.
* st,accel
- Add support for IIS328DQ (ID only as compatible wtih LIS331DL)
* st,lsm6dsx
- Add support for ASM330LHB automotive MEMS sensor.
* ti,ads1100, ads1000
- New driver for these 16 bit ADCs.
* ti,tmp117
- Add support for older tmp116 device. Includes some general driver cleanup.
Staging driver drops
* adi,ade7854
- Driver was a very long way from compliant with IIO infrastructure and ABI.
If anyone wants a non staging version of this driver they are better off
starting from scratch. Hence drop it and the associated meter.h header.
Features
* adi,ad7441r
- Add DT binding to set sink current for digital input.
* semtech,sx9324,9360
- Support older register mapping from firmware designed for windows.
Core improvements.
* Move iio_trigger_poll() docs to next to the implementation and add a note
on expected caller context.
* Rename iio_trigger_poll_chained() to iio_trigger_poll_nested() so
as to use more standard / common terminology.
* Improve main ABI docs references to offset and scale for raw values by
making them consistent and clear.
Cleanups and minor fixes:
* adi,ad5592r
- Add GPIO names - useful for debug.
* adi,ad7441r
- Fix current input, loop powered mode configuration setup.
* adi,adis16475
- Fix wrong commented value for minimum advised lower rate.
* adi,admv1013
- Use devm_clk_get_enabled() to reduce boilerplate.
* adi,ads1210
- Fix wrong bits for writing config register (late fix and has
been broken a long time so not rushed upstream)
* amlogic,meson-saradc
- Improve cleanup in error handling if BL30 handshake fails.
* apex-embedded,stx104
- Migrate to regmap and use regmap_read_poll_timeout() to neatly handle
retries.
- Add local mutex to close various races.
- Use define U16_MAX rather than value for limit.
- Improve code readability with minor reorganization.
* atmel,ad91-sama5d2
- Drop trivial dead code.
* kionix,kx022a
- Drop unused structure element.
* linear,ltc2983
- Reorganize bindings doc to enable unevaluatedProperties to be set
in one place for all child nodes.
- Make binding for adi,custom-thermocouple accept signed values.
* maxim,max44000
- Add OF Device matching (of_match_table was not correctly set).
* maxim,max5522
- Missing static
* measurement-computing,cio-dac
- Fix wrong part name in comments.
- Migrate to regmap.
- Improve includes by replacing bitops.h with more direct bits.h
* qcom,pm8xxx-xoadc
- Remove a check that can never fail.
* renesas,rcar-gyroadc
- DT binding documentation improvements.
- Tidy up an unused warning with __maybe_unused.
* semtech,sx_common
- Drop docs for a structure element that doesn't exist.
* semtech,sx9500
- Drop ACPI_PTR() and of_match_ptr() protections that just complicate
the code / block some firmware registration types that would otherwise
work.
* sensiron,sps30
- Comment formatting tidy up.
* st,sensors
- Drop duplicate text in DT binding.
* st,stm32-adc
- Add some missing static markings.
* ti,ads1100
- Use correct return code in dev_err_probe() call.
* x-powers,axp20x_adc - precursor series to simplify addition of AXP192.
- General code cleanup / minor refactoring for better readabilty of code.
- Switch from boolean value to mask for adc_en2 field to avoid hard coding
a mask that will be different in AXP192
-----BEGIN PGP SIGNATURE-----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=xxs6
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanups for the 6.4 cycle.
New device support
* bosch,bmp280
- Add support for BMP580 - includes significant refactoring and general
driver cleanup + support for non-volatile memory for trimming and config
parameters.
* rohm BU27034
- New driver for this 3 channel ambient light sensor.
- New support library for devices where both integration time and
amplifier gain are configurable. In these cases a scale change
may require changing bother underlying values. This library module
provides code to help with this.
* st,accel
- Add support for IIS328DQ (ID only as compatible wtih LIS331DL)
* st,lsm6dsx
- Add support for ASM330LHB automotive MEMS sensor.
* ti,ads1100, ads1000
- New driver for these 16 bit ADCs.
* ti,tmp117
- Add support for older tmp116 device. Includes some general driver cleanup.
Staging driver drops
* adi,ade7854
- Driver was a very long way from compliant with IIO infrastructure and ABI.
If anyone wants a non staging version of this driver they are better off
starting from scratch. Hence drop it and the associated meter.h header.
Features
* adi,ad7441r
- Add DT binding to set sink current for digital input.
* semtech,sx9324,9360
- Support older register mapping from firmware designed for windows.
Core improvements.
* Move iio_trigger_poll() docs to next to the implementation and add a note
on expected caller context.
* Rename iio_trigger_poll_chained() to iio_trigger_poll_nested() so
as to use more standard / common terminology.
* Improve main ABI docs references to offset and scale for raw values by
making them consistent and clear.
Cleanups and minor fixes:
* adi,ad5592r
- Add GPIO names - useful for debug.
* adi,ad7441r
- Fix current input, loop powered mode configuration setup.
* adi,adis16475
- Fix wrong commented value for minimum advised lower rate.
* adi,admv1013
- Use devm_clk_get_enabled() to reduce boilerplate.
* adi,ads1210
- Fix wrong bits for writing config register (late fix and has
been broken a long time so not rushed upstream)
* amlogic,meson-saradc
- Improve cleanup in error handling if BL30 handshake fails.
* apex-embedded,stx104
- Migrate to regmap and use regmap_read_poll_timeout() to neatly handle
retries.
- Add local mutex to close various races.
- Use define U16_MAX rather than value for limit.
- Improve code readability with minor reorganization.
* atmel,ad91-sama5d2
- Drop trivial dead code.
* kionix,kx022a
- Drop unused structure element.
* linear,ltc2983
- Reorganize bindings doc to enable unevaluatedProperties to be set
in one place for all child nodes.
- Make binding for adi,custom-thermocouple accept signed values.
* maxim,max44000
- Add OF Device matching (of_match_table was not correctly set).
* maxim,max5522
- Missing static
* measurement-computing,cio-dac
- Fix wrong part name in comments.
- Migrate to regmap.
- Improve includes by replacing bitops.h with more direct bits.h
* qcom,pm8xxx-xoadc
- Remove a check that can never fail.
* renesas,rcar-gyroadc
- DT binding documentation improvements.
- Tidy up an unused warning with __maybe_unused.
* semtech,sx_common
- Drop docs for a structure element that doesn't exist.
* semtech,sx9500
- Drop ACPI_PTR() and of_match_ptr() protections that just complicate
the code / block some firmware registration types that would otherwise
work.
* sensiron,sps30
- Comment formatting tidy up.
* st,sensors
- Drop duplicate text in DT binding.
* st,stm32-adc
- Add some missing static markings.
* ti,ads1100
- Use correct return code in dev_err_probe() call.
* x-powers,axp20x_adc - precursor series to simplify addition of AXP192.
- General code cleanup / minor refactoring for better readabilty of code.
- Switch from boolean value to mask for adc_en2 field to avoid hard coding
a mask that will be different in AXP192
* tag 'iio-for-6.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (63 commits)
MAINTAINERS: Add ROHM BU27034
iio: light: ROHM BU27034 Ambient Light Sensor
dt-bindings: iio: light: Support ROHM BU27034
MAINTAINERS: Add IIO gain-time-scale helpers
iio: light: Add gain-time-scale helpers
doc: Make sysfs-bus-iio doc more exact
iio: dac: set variable max5522_channels storage-class-specifier to static
dt-bindings: iio: temperature: ltc2983: Make 'adi,custom-thermocouple' signed
dt-bindings: iio: temperature: ltc2983: Fix child node unevaluated properties
iio: addac: stx104: Use regmap_read_poll_timeout() for conversion poll
iio: addac: stx104: Migrate to the regmap API
iio: addac: stx104: Improve indentation in stx104_write_raw()
iio: addac: stx104: Use define rather than hardcoded limit for write val
iio: addac: stx104: Fix race condition when converting analog-to-digital
iio: addac: stx104: Fix race condition for stx104_write_raw()
dt-bindings: iio: st-sensors: Fix repeated text
staging: iio: resolver: ads1210: fix config mode
iio: adc: ti-ads1100: fix error code in probe()
iio: accel: add support for IIS328DQ variant
dt-bindings: iio: st-sensors: Add IIS328DQ accelerometer
...
ROHM BU27034 is an ambient light sensor with 3 channels and 3 photo diodes
capable of detecting a very wide range of illuminance. Typical application
is adjusting LCD and backlight power of TVs and mobile phones.
Add initial support for the ROHM BU27034 ambient light sensor.
NOTE:
- Driver exposes 4 channels. One IIO_LIGHT channel providing the
calculated lux values based on measured data from diodes #0 and
#1. In addition, 3 IIO_INTENSITY channels are emitting the raw
register data from all diodes for more intense user-space
computations.
- Sensor has GAIN values that can be adjusted from 1x to 4096x.
- Sensor has adjustible measurement times of 5, 55, 100, 200 and
400 mS. Driver does not support 5 mS which has special
limitations.
- Driver exposes standard 'scale' adjustment which is
implemented by:
1) Trying to adjust only the GAIN
2) If GAIN adjustment alone can't provide requested
scale, adjusting both the time and the gain is
attempted.
- Driver exposes writable INT_TIME property that can be used
for adjusting the measurement time. Time adjustment will also
cause the driver to try to adjust the GAIN so that the
overall scale is kept as close to the original as possible.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/2a7efb6f335da5526fbe34b95137c5e45db5c5d3.1680263956.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
tsl2772_read_prox_diodes() will correctly parse the properties from
device tree to determine which proximity diode(s) to read from, however
it didn't actually set this value on the struct tsl2772_settings. Let's
go ahead and fix that.
Reported-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/lkml/20230327120823.1369700-1-trix@redhat.com/
Fixes: 94cd1113aa ("iio: tsl2772: add support for reading proximity led settings from device tree")
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/20230404011455.339454-1-bmasney@redhat.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
