Adds driver for the MCP48xx series of DACs.
Device uses a simplex SPI channel. To set the value of an output channel,
a 16-bit data of following format must be written:
Bit field | Description
15 [MSB] | Channel selection bit
0 -> Channel A
1 -> Channel B
13 | Output Gain Selection bit
0 -> 2x Gain (Vref = 4.096V)
1 -> 1x Gain (Vref = 2.048V)
12 | Output Shutdown Control bit
0 -> Shutdown the selected channel
1 -> Active mode operation
11-0 [LSB]| DAC Input Data bits
Value's big endian representation is taken as input for the
selected DAC channel. For devices with a resolution of less
than 12-bits, only the x most significant bits are considered
where x is the resolution of the device.
Reference: Page#22 [MCP48x2 Datasheet]
Supported devices:
+---------+--------------+-------------+
| Device | Resolution | Channels |
|---------|--------------|-------------|
| MCP4801 | 8-bit | 1 |
| MCP4802 | 8-bit | 2 |
| MCP4811 | 10-bit | 1 |
| MCP4812 | 10-bit | 2 |
| MCP4821 | 12-bit | 1 |
| MCP4822 | 12-bit | 2 |
+---------+--------------+-------------+
Devices tested:
MCP4821 [12-bit single channel]
MCP4802 [8-bit dual channel]
Tested on Raspberry Pi Zero 2W
Datasheet: https://ww1.microchip.com/downloads/en/DeviceDoc/22244B.pdf #MCP48x1
Datasheet: https://ww1.microchip.com/downloads/en/DeviceDoc/20002249B.pdf #MCP48x2
Signed-off-by: Anshul Dalal <anshulusr@gmail.com>
Link: https://lore.kernel.org/r/20231220151954.154595-2-anshulusr@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for an external amplifier to be connected in a
gain of two configuration.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20231129-ad5791-michael-stuff-v3-2-48e192b00909@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Particularly great to see a resolver driver move out of staging via a
massive set of changes. Only took 13 years :)
One small patch added then reverted due to a report of test breakage
(ashai-kasei,ak8975: Drop deprecated enums.)
An immutable branch was used for some hid-senors changes in case
there was a need to take them into the HID tree as well.
New device support
-----------------
adi,hmc425a
- Add support for HMC540SLP3E broadband 4-bit digital attenuator.
kionix,kx022a
- Add support for the kx132-1211 accelerometer. Require significant
driver rework to enable this including add a chip type specific
structure to deal with the chip differences.
- Add support for the kx132acr-lbz accelerometer (subset of the kx022a
feature set).
lltc,ltc2309
- New driver for this 8 channel ADC.
microchip,mcp3911
- Add support for rest of mcp391x family of ADCs (there are various
differences beyond simple channel count variation.
Series includes some general driver cleanup.
microchip,mcp3564
- New driver for MCP3461, MCP3462, MCP3464, MCP3541, MCP3562, MCP3564
and their R variants of 16/24bit ADCs. A few minor fixed followed.
rohm,bu1390
- New driver for this pressure sensor.
Staging graduation
------------------
adi,ad1210 (after 13 or so years :)
- More or less a complete (step-wise) rewrite of this resolver driver
to bring it up to date with modern IIO standards. The fault signal
handling mapping to event channels was particularly complex and
significant part of the changes.
Features
--------
iio-core
- Add chromacity and color temperature channel types.
adi,ad7192
- Oversampling ratio control (called fast settling in datasheet).
adi,adis16475
- Add core support and then driver support for delta angle and delta
velocity channels. These are intended for summation to establish
angle and velocity changes over larger timescales. Fix was
needed for alignment after the temperature channel. Further fix
reduced set of devices for which the buffer support was applicable
as seems burst reads don't cover these on all devices.
hid-sensors-als
- Chromacity and color temperatures support including in amd sfh.
stx104
- Add support for counter subsystem to this multipurpose device.
ti,twl6030
- Add missing device tree binding description.
Clean up and minor fixes.
------------------------
treewide
- Drop some unused declarations across IIO.
- Make more use of device_get_match_data() instead of OF specific
approaches.
Similar cleanup to sets of drivers.
- Stop platform remove callbacks returning anything by using the
temporary remove_new() callback.
- Use i2c_get_match_data() to cope nicely with all types of ID table
entry.
- Use device_get_match_data() for various platform device to cope
with more types of firmware.
- Convert from enum to pointer in ID tables allowing use of
i2c_get_match_data().
- Fix sorting on some ID tables.
- Include specific string helper headers rather than simply string_helpers.h
docs
- Better description of the ordering requirements etc for
available_scan_masks.
tools
- Handle alignment of mixed sizes where the last element isn't the biggest
correctly. Seems that doesn't happen often!
adi,ad2s1210
- Lots of work from David Lechner on this driver including a few fixes
that are going with the rework to avoid slowing that down.
adi,ad4310
- Replace deprecated devm_clk_register()
adi,ad74413r
- Bring the channel function setting inline with the datasheet.
adi,ad7192
- Change to FIELD_PREP(), FIELD_GET().
- Calculate f_order from the sinc filter and chop filter states.
- Move more per chip config into data in struct ad7192_chip_info
- Cleanup unused parameter in channel macros.
adi,adf4350
- Make use of devm_* to simplify error handling for many of the setup
calls in probe() / tear down in remove() and error paths. Some more
work to be done on this one.
- Use dev_err_probe() for errors in probe() callback.
adi,adf4413
- Typo in function name prefix.
adi,adxl345
- Add channel scale to the chip type specific structure and drop
using a type field previously used for indirection.
asahi,ak8985
- Fix a mismatch introduced when switching from enum->pointers
in the match tables.
amlogic,meson
- Expand error logging during probe.
invensense,mpu6050
- Support level-shifter control. Whilst no one is sure exactly what this
is doing it is needed for some old boards.
- Document mount-matrix dt-binding.
mediatek,mt6577
- Use devm_clk_get_enabled() to replace open coded version and move
everything over to being device managed. Drop now empty remove()
callback. Fix follows to put the drvdata back.
- Use dev_err_probe() for error reporting in probe() callback.
memsic,mxc4005
- Add of_match_table.
microchip,mcp4725
- Move various chip specific data from being looked up by chip ID to
data in the chip type specific structure.
silicon-labs,si7005
- Add of_match_table and entry in trivial-devices.yaml
st,lsm6dsx
- Add missing mount-matrix dt binding documentation.
st,spear
- Use devm_clk_get_enabled() and some other devm calls to move everything
over to being device managed. Drop now empty remove() callback.
- Use dev_err_probe() to better handled deferred probing and tidy up
error reporting in probe() callback.
st,stm32-adc
- Add a bit of additional checking in probe() to protect against a NULL
pointer (no known path to trigger it today).
- Replace deprecated strncpy()
ti,ads1015
- Allow for edge triggers.
- Document interrupt in dt-bindings.
-----BEGIN PGP SIGNATURE-----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=wth0
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.7a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: 1st set of new device support, features and cleanup for 6.7
Particularly great to see a resolver driver move out of staging via a
massive set of changes. Only took 13 years :)
One small patch added then reverted due to a report of test breakage
(ashai-kasei,ak8975: Drop deprecated enums.)
An immutable branch was used for some hid-senors changes in case
there was a need to take them into the HID tree as well.
New device support
-----------------
adi,hmc425a
- Add support for HMC540SLP3E broadband 4-bit digital attenuator.
kionix,kx022a
- Add support for the kx132-1211 accelerometer. Require significant
driver rework to enable this including add a chip type specific
structure to deal with the chip differences.
- Add support for the kx132acr-lbz accelerometer (subset of the kx022a
feature set).
lltc,ltc2309
- New driver for this 8 channel ADC.
microchip,mcp3911
- Add support for rest of mcp391x family of ADCs (there are various
differences beyond simple channel count variation.
Series includes some general driver cleanup.
microchip,mcp3564
- New driver for MCP3461, MCP3462, MCP3464, MCP3541, MCP3562, MCP3564
and their R variants of 16/24bit ADCs. A few minor fixed followed.
rohm,bu1390
- New driver for this pressure sensor.
Staging graduation
------------------
adi,ad1210 (after 13 or so years :)
- More or less a complete (step-wise) rewrite of this resolver driver
to bring it up to date with modern IIO standards. The fault signal
handling mapping to event channels was particularly complex and
significant part of the changes.
Features
--------
iio-core
- Add chromacity and color temperature channel types.
adi,ad7192
- Oversampling ratio control (called fast settling in datasheet).
adi,adis16475
- Add core support and then driver support for delta angle and delta
velocity channels. These are intended for summation to establish
angle and velocity changes over larger timescales. Fix was
needed for alignment after the temperature channel. Further fix
reduced set of devices for which the buffer support was applicable
as seems burst reads don't cover these on all devices.
hid-sensors-als
- Chromacity and color temperatures support including in amd sfh.
stx104
- Add support for counter subsystem to this multipurpose device.
ti,twl6030
- Add missing device tree binding description.
Clean up and minor fixes.
------------------------
treewide
- Drop some unused declarations across IIO.
- Make more use of device_get_match_data() instead of OF specific
approaches.
Similar cleanup to sets of drivers.
- Stop platform remove callbacks returning anything by using the
temporary remove_new() callback.
- Use i2c_get_match_data() to cope nicely with all types of ID table
entry.
- Use device_get_match_data() for various platform device to cope
with more types of firmware.
- Convert from enum to pointer in ID tables allowing use of
i2c_get_match_data().
- Fix sorting on some ID tables.
- Include specific string helper headers rather than simply string_helpers.h
docs
- Better description of the ordering requirements etc for
available_scan_masks.
tools
- Handle alignment of mixed sizes where the last element isn't the biggest
correctly. Seems that doesn't happen often!
adi,ad2s1210
- Lots of work from David Lechner on this driver including a few fixes
that are going with the rework to avoid slowing that down.
adi,ad4310
- Replace deprecated devm_clk_register()
adi,ad74413r
- Bring the channel function setting inline with the datasheet.
adi,ad7192
- Change to FIELD_PREP(), FIELD_GET().
- Calculate f_order from the sinc filter and chop filter states.
- Move more per chip config into data in struct ad7192_chip_info
- Cleanup unused parameter in channel macros.
adi,adf4350
- Make use of devm_* to simplify error handling for many of the setup
calls in probe() / tear down in remove() and error paths. Some more
work to be done on this one.
- Use dev_err_probe() for errors in probe() callback.
adi,adf4413
- Typo in function name prefix.
adi,adxl345
- Add channel scale to the chip type specific structure and drop
using a type field previously used for indirection.
asahi,ak8985
- Fix a mismatch introduced when switching from enum->pointers
in the match tables.
amlogic,meson
- Expand error logging during probe.
invensense,mpu6050
- Support level-shifter control. Whilst no one is sure exactly what this
is doing it is needed for some old boards.
- Document mount-matrix dt-binding.
mediatek,mt6577
- Use devm_clk_get_enabled() to replace open coded version and move
everything over to being device managed. Drop now empty remove()
callback. Fix follows to put the drvdata back.
- Use dev_err_probe() for error reporting in probe() callback.
memsic,mxc4005
- Add of_match_table.
microchip,mcp4725
- Move various chip specific data from being looked up by chip ID to
data in the chip type specific structure.
silicon-labs,si7005
- Add of_match_table and entry in trivial-devices.yaml
st,lsm6dsx
- Add missing mount-matrix dt binding documentation.
st,spear
- Use devm_clk_get_enabled() and some other devm calls to move everything
over to being device managed. Drop now empty remove() callback.
- Use dev_err_probe() to better handled deferred probing and tidy up
error reporting in probe() callback.
st,stm32-adc
- Add a bit of additional checking in probe() to protect against a NULL
pointer (no known path to trigger it today).
- Replace deprecated strncpy()
ti,ads1015
- Allow for edge triggers.
- Document interrupt in dt-bindings.
* tag 'iio-for-6.7a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (201 commits)
iio: Use device_get_match_data()
iio: adc: MCP3564: fix warn: unsigned '__x' is never less than zero.
dt-bindings: trivial-devices: add silabs,si7005
iio: si7005: Add device tree support
drivers: imu: adis16475.c: Remove scan index from delta channels
dt-bindings: iio: imu: st,lsm6dsx: add mount-matrix property
iio: resolver: ad2s1210: remove of_match_ptr()
iio: resolver: ad2s1210: remove DRV_NAME macro
iio: resolver: ad2s1210: move out of staging
staging: iio: resolver: ad2s1210: simplify code with guard(mutex)
staging: iio: resolver: ad2s1210: clear faults after soft reset
staging: iio: resolver: ad2s1210: refactor sample toggle
staging: iio: resolver: ad2s1210: remove fault attribute
staging: iio: resolver: ad2s1210: add label attribute support
staging: iio: resolver: ad2s1210: add register/fault support summary
staging: iio: resolver: ad2s1210: implement fault events
iio: event: add optional event label support
staging: iio: resolver: ad2s1210: rename DOS reset min/max attrs
staging: iio: resolver: ad2s1210: convert DOS mismatch threshold to event attr
staging: iio: resolver: ad2s1210: convert DOS overrange threshold to event attr
...
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231006224440.442864-1-robh@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-34-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-33-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-32-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-31-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-30-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The MCP4725 has a register offset '3' for reading DAC value compared to
'4' for MCP4726. Add dac_reg_offset variable to struct mcp4725_chip_info
to handle this difference.
Drop chip_id from struct mcp4725_chip_info as it is unused.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230903115548.59306-5-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The MCP4725 has external voltage reference compared MCP4725 which
has reference embeedded in eeprom. Add use_ext_ref_voltage variable
to struct mcp4725_chip_info to handle this difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230903115548.59306-4-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add struct mcp4725_chip_info with chan_spec and chip_id variable.
After this simplify probe() by replacing device_get_match_data() and id
lookup for retrieving match data by i2c_get_match_data() by converting
enum->pointer for data in the match table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230903115548.59306-3-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace the variable 'id' from struct mcp4725_data with local variable
chip_id in probe() as the id variable is not used elsewhere in the
driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230903115548.59306-2-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Device IDs for AD3542R and AD3552R were swapped leading to unintended
collection of DAC output ranges being used for each design.
Change device ID values so they are correct for each DAC chip.
Fixes: 8f2b54824b ("drivers:iio:dac: Add AD3552R driver support")
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Reported-by: Chandrakant Minajigi <Chandrakant.Minajigi@analog.com>
Link: https://lore.kernel.org/r/011f480220799fbfabdd53896f8a2f251ad995ad.1691091324.git.marcelo.schmitt1@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sort ID table alphabetically by name and OF table by compatible
for single_*bit enums.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20230818173907.323640-3-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace device_get_match_data() and id lookup for retrieving match data
by i2c_get_match_data() by converting enum->pointer for data in the
match table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230818173907.323640-2-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MCP4728 is a 12-bit quad channel DAC with I2C interface.
support for:
* per-channel gain
* per-channel power state
* per-channel power down mode control
* per-channel vref selection internal/vdd
* store current state to on-chip EEPROM
Signed-off-by: Andrea Collamati <andrea.collamati@gmail.com>
Link: https://lore.kernel.org/r/a0933003ed3c855f9d80d6ce0a40add2b6f0ba36.1691066050.git.andrea.collamati@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New device support
- honeywell,mprls0025pa
* New driver and dt-bindings for this series of pressure sensors.
- invensense,mpu6050
* Add support for ICM 20600 IMU (ID, bindings and device data).
- melexis,mlx90614
* Add support for mlx90615 Infra Red Thermometer after driver cleanup
and refactoring to support the differences in this device.
- renesas,x9250
* New driver and bindings for this quad potentiometer.
- rockchip,saradc
* Add support for RK3588. Also included is a bunch of refactoring and
cleanup for that driver.
- rohm,bu27008
* New driver bindings etc for this 5 photodiode color sensor.
- st,lsm9ds0/st,st-sensors
* ID added for LSM303D accelerometer and magnetometer including ACPI binding.
- ti,opt4001
* New driver and bindings for this ambient light sensor.
Features
- core
* Introduce iio_validate_own_trigger() for cases where a driver can only
consumer a trigger it registered (detected via same parent device).
Use it in the kionix,kx022a driver and new rohm,by27008 driver.
- dynaimage,al3320a
* ACPI binding CALS0001 seen on Lenovo Yoga Table 2 devices.
- kionix,kx002a
* Enable asynchronous probe.
- rohm,bu27034
* Enable asynchronous probe.
- ti,tmp006
* Explicit support for DT including binding documentation.
Cleanups, minor fixes and misc improvements.
- treewide
* Switch I2C drivers from probe_new() back to probe() - part of the
long process of getting rid of a parameter from probe()
* Various whitespace and typo fixes not otherwise called out.
- core
* industrialio-buffer,Style cleanup.
* Add documentation to extend_name field of struct iio_chan_spec to
direct people using it towards the label infrastructure instead.
extend_name was a design mistake a long time back so directly people
away from it may be useful.
- adi,ad7606
* Add HAS_IOPORT dependency to prepare for some Kconfig changes.
- bosch,bma400
* Drop pointless print of ret in a dev_err_probe() message.
- invensense,icm42600
* Rework timestamp handling to reduce jitter.
- mediatek,mt7986-auxdac
* Add DT binding for this part.
- qcom,spmi-vadc
* Allow for 1/16th prescaling used on a few devices.
* Various changes to channel labeling and naming, including dropping
use of fwnode_name which generates odd channel names. Small ABI
change as a result, but not thought to be a problem for users of this
platform.
- st,lsm6dsx
* dt-binding: Use common schema for mount-matrix via a reference.
- st,stm32
* Add a debug print for when legacy channel config is used.
- ti,palmas-adc
* Drop unused i2c.h include.
-----BEGIN PGP SIGNATURE-----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=0gJ9
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.5a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanup for the 6.5 cycle.
New device support
- honeywell,mprls0025pa
* New driver and dt-bindings for this series of pressure sensors.
- invensense,mpu6050
* Add support for ICM 20600 IMU (ID, bindings and device data).
- melexis,mlx90614
* Add support for mlx90615 Infra Red Thermometer after driver cleanup
and refactoring to support the differences in this device.
- renesas,x9250
* New driver and bindings for this quad potentiometer.
- rockchip,saradc
* Add support for RK3588. Also included is a bunch of refactoring and
cleanup for that driver.
- rohm,bu27008
* New driver bindings etc for this 5 photodiode color sensor.
- st,lsm9ds0/st,st-sensors
* ID added for LSM303D accelerometer and magnetometer including ACPI binding.
- ti,opt4001
* New driver and bindings for this ambient light sensor.
Features
- core
* Introduce iio_validate_own_trigger() for cases where a driver can only
consumer a trigger it registered (detected via same parent device).
Use it in the kionix,kx022a driver and new rohm,by27008 driver.
- dynaimage,al3320a
* ACPI binding CALS0001 seen on Lenovo Yoga Table 2 devices.
- kionix,kx002a
* Enable asynchronous probe.
- rohm,bu27034
* Enable asynchronous probe.
- ti,tmp006
* Explicit support for DT including binding documentation.
Cleanups, minor fixes and misc improvements.
- treewide
* Switch I2C drivers from probe_new() back to probe() - part of the
long process of getting rid of a parameter from probe()
* Various whitespace and typo fixes not otherwise called out.
- core
* industrialio-buffer,Style cleanup.
* Add documentation to extend_name field of struct iio_chan_spec to
direct people using it towards the label infrastructure instead.
extend_name was a design mistake a long time back so directly people
away from it may be useful.
- adi,ad7606
* Add HAS_IOPORT dependency to prepare for some Kconfig changes.
- bosch,bma400
* Drop pointless print of ret in a dev_err_probe() message.
- invensense,icm42600
* Rework timestamp handling to reduce jitter.
- mediatek,mt7986-auxdac
* Add DT binding for this part.
- qcom,spmi-vadc
* Allow for 1/16th prescaling used on a few devices.
* Various changes to channel labeling and naming, including dropping
use of fwnode_name which generates odd channel names. Small ABI
change as a result, but not thought to be a problem for users of this
platform.
- st,lsm6dsx
* dt-binding: Use common schema for mount-matrix via a reference.
- st,stm32
* Add a debug print for when legacy channel config is used.
- ti,palmas-adc
* Drop unused i2c.h include.
* tag 'iio-for-6.5a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (59 commits)
dt-bindings: iio: rockchip: Fix 'oneOf' condition failed warning
dt-bindings: iio: afe: voltage-divider: Spelling s/curcuit/circuit/
dt-bindings: iio: adc: Add rockchip,rk3588-saradc string
iio: adc: rockchip_saradc: Use dev_err_probe
iio: adc: rockchip_saradc: Match alignment with open parenthesis
iio: adc: rockchip_saradc: Use of_device_get_match_data
iio: adc: rockchip_saradc: Make use of devm_clk_get_enabled
iio: adc: rockchip_saradc: Add support for RK3588
iio: adc: rockchip_saradc: Add callback functions
iio: temperature: tmp006: Add OF device matching support
dt-bindings: iio: temperature: Add support for tmp006
staging: iio: Switch i2c drivers back to use .probe()
iio: amplifiers: ad8366 Fix whitespace issue
iio: imu: inv_icm42600: avoid frequent timestamp jitter
MAINTAINERS: Add ROHM BU27008
iio: light: ROHM BU27008 color sensor
iio: kx022a: Use new iio_validate_own_trigger()
iio: trigger: Add simple trigger_validation helper
dt-bindings: iio: light: ROHM BU27008
iio: mlx90614: Add MLX90615 support
...
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230515205048.19561-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The i2c_master_send() returns number of sent bytes on success,
or negative on error. The suspend/resume callbacks expect zero
on success and non-zero on error. Adapt the return value of the
i2c_master_send() to the expectation of the suspend and resume
callbacks, including proper validation of the return value.
Fixes: cf35ad61ac ("iio: add mcp4725 I2C DAC driver")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230511004330.206942-1-marex@denx.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 28d1a7ac2a ("iio: dac: Add AD5758 support") adds the config AD5758
and the corresponding driver ad5758.c. In the Makefile, the ad5758 driver
is however included when AD5755 is selected, not when AD5758 is selected.
Probably, this was simply a mistake that happened by copy-and-paste and
forgetting to adjust the actual line. Surprisingly, no one has ever noticed
that this driver is actually only included when AD5755 is selected and that
the config AD5758 has actually no effect on the build.
Fixes: 28d1a7ac2a ("iio: dac: Add AD5758 support")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20230508040208.12033-1-lukas.bulwahn@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost breaks
even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp5Eg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynSXgCg0kSw3vUYwpsnhAsQkoPw1QVA23sAn2edRCMa
GEkPWjrROueCom7xbLMu
=eR+P
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc drivers updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost
breaks even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (196 commits)
mcb-lpc: Reallocate memory region to avoid memory overlapping
mcb-pci: Reallocate memory region to avoid memory overlapping
mcb: Return actual parsed size when reading chameleon table
kernel/configs: Drop Android config fragments
virt: acrn: Replace obsolete memalign() with posix_memalign()
spmi: Add a check for remove callback when removing a SPMI driver
spmi: fix W=1 kernel-doc warnings
spmi: mtk-pmif: Drop of_match_ptr for ID table
spmi: pmic-arb: Convert to platform remove callback returning void
spmi: mtk-pmif: Convert to platform remove callback returning void
spmi: hisi-spmi-controller: Convert to platform remove callback returning void
w1: gpio: remove unnecessary ENOMEM messages
w1: omap-hdq: remove unnecessary ENOMEM messages
w1: omap-hdq: add SPDX tag
w1: omap-hdq: allow compile testing
w1: matrox: remove unnecessary ENOMEM messages
w1: matrox: use inline over __inline__
w1: matrox: switch from asm to linux header
w1: ds2482: do not use assignment in if condition
w1: ds2482: drop unnecessary header
...
New device support
* bosch,bmp280
- Add support for BMP580 - includes significant refactoring and general
driver cleanup + support for non-volatile memory for trimming and config
parameters.
* rohm BU27034
- New driver for this 3 channel ambient light sensor.
- New support library for devices where both integration time and
amplifier gain are configurable. In these cases a scale change
may require changing bother underlying values. This library module
provides code to help with this.
* st,accel
- Add support for IIS328DQ (ID only as compatible wtih LIS331DL)
* st,lsm6dsx
- Add support for ASM330LHB automotive MEMS sensor.
* ti,ads1100, ads1000
- New driver for these 16 bit ADCs.
* ti,tmp117
- Add support for older tmp116 device. Includes some general driver cleanup.
Staging driver drops
* adi,ade7854
- Driver was a very long way from compliant with IIO infrastructure and ABI.
If anyone wants a non staging version of this driver they are better off
starting from scratch. Hence drop it and the associated meter.h header.
Features
* adi,ad7441r
- Add DT binding to set sink current for digital input.
* semtech,sx9324,9360
- Support older register mapping from firmware designed for windows.
Core improvements.
* Move iio_trigger_poll() docs to next to the implementation and add a note
on expected caller context.
* Rename iio_trigger_poll_chained() to iio_trigger_poll_nested() so
as to use more standard / common terminology.
* Improve main ABI docs references to offset and scale for raw values by
making them consistent and clear.
Cleanups and minor fixes:
* adi,ad5592r
- Add GPIO names - useful for debug.
* adi,ad7441r
- Fix current input, loop powered mode configuration setup.
* adi,adis16475
- Fix wrong commented value for minimum advised lower rate.
* adi,admv1013
- Use devm_clk_get_enabled() to reduce boilerplate.
* adi,ads1210
- Fix wrong bits for writing config register (late fix and has
been broken a long time so not rushed upstream)
* amlogic,meson-saradc
- Improve cleanup in error handling if BL30 handshake fails.
* apex-embedded,stx104
- Migrate to regmap and use regmap_read_poll_timeout() to neatly handle
retries.
- Add local mutex to close various races.
- Use define U16_MAX rather than value for limit.
- Improve code readability with minor reorganization.
* atmel,ad91-sama5d2
- Drop trivial dead code.
* kionix,kx022a
- Drop unused structure element.
* linear,ltc2983
- Reorganize bindings doc to enable unevaluatedProperties to be set
in one place for all child nodes.
- Make binding for adi,custom-thermocouple accept signed values.
* maxim,max44000
- Add OF Device matching (of_match_table was not correctly set).
* maxim,max5522
- Missing static
* measurement-computing,cio-dac
- Fix wrong part name in comments.
- Migrate to regmap.
- Improve includes by replacing bitops.h with more direct bits.h
* qcom,pm8xxx-xoadc
- Remove a check that can never fail.
* renesas,rcar-gyroadc
- DT binding documentation improvements.
- Tidy up an unused warning with __maybe_unused.
* semtech,sx_common
- Drop docs for a structure element that doesn't exist.
* semtech,sx9500
- Drop ACPI_PTR() and of_match_ptr() protections that just complicate
the code / block some firmware registration types that would otherwise
work.
* sensiron,sps30
- Comment formatting tidy up.
* st,sensors
- Drop duplicate text in DT binding.
* st,stm32-adc
- Add some missing static markings.
* ti,ads1100
- Use correct return code in dev_err_probe() call.
* x-powers,axp20x_adc - precursor series to simplify addition of AXP192.
- General code cleanup / minor refactoring for better readabilty of code.
- Switch from boolean value to mask for adc_en2 field to avoid hard coding
a mask that will be different in AXP192
-----BEGIN PGP SIGNATURE-----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=xxs6
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanups for the 6.4 cycle.
New device support
* bosch,bmp280
- Add support for BMP580 - includes significant refactoring and general
driver cleanup + support for non-volatile memory for trimming and config
parameters.
* rohm BU27034
- New driver for this 3 channel ambient light sensor.
- New support library for devices where both integration time and
amplifier gain are configurable. In these cases a scale change
may require changing bother underlying values. This library module
provides code to help with this.
* st,accel
- Add support for IIS328DQ (ID only as compatible wtih LIS331DL)
* st,lsm6dsx
- Add support for ASM330LHB automotive MEMS sensor.
* ti,ads1100, ads1000
- New driver for these 16 bit ADCs.
* ti,tmp117
- Add support for older tmp116 device. Includes some general driver cleanup.
Staging driver drops
* adi,ade7854
- Driver was a very long way from compliant with IIO infrastructure and ABI.
If anyone wants a non staging version of this driver they are better off
starting from scratch. Hence drop it and the associated meter.h header.
Features
* adi,ad7441r
- Add DT binding to set sink current for digital input.
* semtech,sx9324,9360
- Support older register mapping from firmware designed for windows.
Core improvements.
* Move iio_trigger_poll() docs to next to the implementation and add a note
on expected caller context.
* Rename iio_trigger_poll_chained() to iio_trigger_poll_nested() so
as to use more standard / common terminology.
* Improve main ABI docs references to offset and scale for raw values by
making them consistent and clear.
Cleanups and minor fixes:
* adi,ad5592r
- Add GPIO names - useful for debug.
* adi,ad7441r
- Fix current input, loop powered mode configuration setup.
* adi,adis16475
- Fix wrong commented value for minimum advised lower rate.
* adi,admv1013
- Use devm_clk_get_enabled() to reduce boilerplate.
* adi,ads1210
- Fix wrong bits for writing config register (late fix and has
been broken a long time so not rushed upstream)
* amlogic,meson-saradc
- Improve cleanup in error handling if BL30 handshake fails.
* apex-embedded,stx104
- Migrate to regmap and use regmap_read_poll_timeout() to neatly handle
retries.
- Add local mutex to close various races.
- Use define U16_MAX rather than value for limit.
- Improve code readability with minor reorganization.
* atmel,ad91-sama5d2
- Drop trivial dead code.
* kionix,kx022a
- Drop unused structure element.
* linear,ltc2983
- Reorganize bindings doc to enable unevaluatedProperties to be set
in one place for all child nodes.
- Make binding for adi,custom-thermocouple accept signed values.
* maxim,max44000
- Add OF Device matching (of_match_table was not correctly set).
* maxim,max5522
- Missing static
* measurement-computing,cio-dac
- Fix wrong part name in comments.
- Migrate to regmap.
- Improve includes by replacing bitops.h with more direct bits.h
* qcom,pm8xxx-xoadc
- Remove a check that can never fail.
* renesas,rcar-gyroadc
- DT binding documentation improvements.
- Tidy up an unused warning with __maybe_unused.
* semtech,sx_common
- Drop docs for a structure element that doesn't exist.
* semtech,sx9500
- Drop ACPI_PTR() and of_match_ptr() protections that just complicate
the code / block some firmware registration types that would otherwise
work.
* sensiron,sps30
- Comment formatting tidy up.
* st,sensors
- Drop duplicate text in DT binding.
* st,stm32-adc
- Add some missing static markings.
* ti,ads1100
- Use correct return code in dev_err_probe() call.
* x-powers,axp20x_adc - precursor series to simplify addition of AXP192.
- General code cleanup / minor refactoring for better readabilty of code.
- Switch from boolean value to mask for adc_en2 field to avoid hard coding
a mask that will be different in AXP192
* tag 'iio-for-6.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (63 commits)
MAINTAINERS: Add ROHM BU27034
iio: light: ROHM BU27034 Ambient Light Sensor
dt-bindings: iio: light: Support ROHM BU27034
MAINTAINERS: Add IIO gain-time-scale helpers
iio: light: Add gain-time-scale helpers
doc: Make sysfs-bus-iio doc more exact
iio: dac: set variable max5522_channels storage-class-specifier to static
dt-bindings: iio: temperature: ltc2983: Make 'adi,custom-thermocouple' signed
dt-bindings: iio: temperature: ltc2983: Fix child node unevaluated properties
iio: addac: stx104: Use regmap_read_poll_timeout() for conversion poll
iio: addac: stx104: Migrate to the regmap API
iio: addac: stx104: Improve indentation in stx104_write_raw()
iio: addac: stx104: Use define rather than hardcoded limit for write val
iio: addac: stx104: Fix race condition when converting analog-to-digital
iio: addac: stx104: Fix race condition for stx104_write_raw()
dt-bindings: iio: st-sensors: Fix repeated text
staging: iio: resolver: ads1210: fix config mode
iio: adc: ti-ads1100: fix error code in probe()
iio: accel: add support for IIS328DQ variant
dt-bindings: iio: st-sensors: Add IIS328DQ accelerometer
...
smatch reports
drivers/iio/dac/max5522.c:55:28: warning: symbol
'max5522_channels' was not declared. Should it be static?
This variable is only used in one file so it should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230404013828.1914523-1-trix@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In ad5755_parse_fw(), we should add fwnode_handle_put()
when break out of the iteration device_for_each_child_node()
as it will automatically increase and decrease the refcounter.
Fixes: 3ac27afefd ("iio:dac:ad5755: Switch to generic firmware properties and drop pdata")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20230322035627.1856421-1-windhl@126.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Usual mixed bag:
- core - output buffers
Fix return of bytes written when only some succeed.
Fix O_NONBLOCK handling to not block.
- adi,ad7791
Fix IRQ type. Not confirmed to have any impact but good to correct it anyway
- adi,adis16400
Missing CONFIG_CRC32
- capella,cm32181
Unregister 2nd I2C client if one is used.
- cio-dac
Fix bitdepth for range check on write.
- linear,ltc2497
Fix a wrong shift of the LSB introduced when switching to be24 handling.
- maxim,max11410
Fix handling of return code in read_poll_timeout()
- qcom,spmi-adc
Fix an accidental change of channel name to include the reg value from OF.
- ti,palmas
Fix a null dereference on remove due to wrong function used to get the
drvdata.
- ti,ads7950
Mark GPIO as can sleep.
-----BEGIN PGP SIGNATURE-----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=8wF1
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-6.3a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus
Jonathan writes:
1st set of IIO fixes for 6.3
Usual mixed bag:
- core - output buffers
Fix return of bytes written when only some succeed.
Fix O_NONBLOCK handling to not block.
- adi,ad7791
Fix IRQ type. Not confirmed to have any impact but good to correct it anyway
- adi,adis16400
Missing CONFIG_CRC32
- capella,cm32181
Unregister 2nd I2C client if one is used.
- cio-dac
Fix bitdepth for range check on write.
- linear,ltc2497
Fix a wrong shift of the LSB introduced when switching to be24 handling.
- maxim,max11410
Fix handling of return code in read_poll_timeout()
- qcom,spmi-adc
Fix an accidental change of channel name to include the reg value from OF.
- ti,palmas
Fix a null dereference on remove due to wrong function used to get the
drvdata.
- ti,ads7950
Mark GPIO as can sleep.
* tag 'iio-fixes-for-6.3a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: ti-ads7950: Set `can_sleep` flag for GPIO chip
iio: adc: palmas_gpadc: fix NULL dereference on rmmod
iio: adc: max11410: fix read_poll_timeout() usage
iio: dac: cio-dac: Fix max DAC write value check for 12-bit
iio: light: cm32181: Unregister second I2C client if present
iio: accel: kionix-kx022a: Get the timestamp from the driver's private data in the trigger_handler
iio: adc: ad7791: fix IRQ flags
iio: buffer: make sure O_NONBLOCK is respected
iio: buffer: correctly return bytes written in output buffers
iio: light: vcnl4000: Fix WARN_ON on uninitialized lock
iio: adis16480: select CONFIG_CRC32
drivers: iio: adc: ltc2497: fix LSB shift
iio: adc: qcom-spmi-adc5: Fix the channel name
The regmap API supports IO port accessors so we can take advantage of
regmap abstractions rather than handling access to the device registers
directly in the driver.
Includes trivial header inclusion tidy up.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/20230311140218.74920-1-william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The CIO-DAC series of devices only supports DAC values up to 12-bit
rather than 16-bit. Trying to write a 16-bit value results in only the
lower 12 bits affecting the DAC output which is not what the user
expects. Instead, adjust the DAC write value check to reject values
larger than 12-bit so that they fail explicitly as invalid for the user.
Fixes: 3b8df5fd52 ("iio: Add IIO support for the Measurement Computing CIO-DAC family")
Cc: stable@vger.kernel.org
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/20230311002248.8548-1-william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add array of explicit gpio names for the `gpiochip` structure of
ad5592r, mainly for debug purposes.
Since the gpios are configurable via the dts, generic names are
used.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20221117090130.51702-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add initial support for DAC max5522.
Tested writing DAC A and B with some values,
from 0 to 1023, measured output voltages, driver works properly.
Additions for max5523/24/25 will follow.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Link: https://lore.kernel.org/r/20221106165928.223318-1-angelo.dureghello@timesys.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
AD5337 belongs to the same family as the AD5338.
The difference is that the AD5337 has 8-bit precision instead of 10-bit.
Add support for the AD5337 chip in the driver.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20221130182632.3856675-2-festevam@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20221118224540.619276-93-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-92-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-91-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-90-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-89-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-88-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-87-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-86-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-85-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-84-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-83-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and features,
the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0GQmA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylyVQCeNJjZ3hy+Wz8WkPSY+NkehuIhyCIAnjXMOJP8
5G/JQ+rpcclr7VOXlS66
=zVkU
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and
features, the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (411 commits)
w1: Split memcpy() of struct cn_msg flexible array
spmi: pmic-arb: increase SPMI transaction timeout delay
spmi: pmic-arb: block access for invalid PMIC arbiter v5 SPMI writes
spmi: pmic-arb: correct duplicate APID to PPID mapping logic
spmi: pmic-arb: add support to dispatch interrupt based on IRQ status
spmi: pmic-arb: check apid against limits before calling irq handler
spmi: pmic-arb: do not ack and clear peripheral interrupts in cleanup_irq
spmi: pmic-arb: handle spurious interrupt
spmi: pmic-arb: add a print in cleanup_irq
drivers: spmi: Directly use ida_alloc()/free()
MAINTAINERS: add TI ECAP driver info
counter: ti-ecap-capture: capture driver support for ECAP
Documentation: ABI: sysfs-bus-counter: add frequency & num_overflows items
dt-bindings: counter: add ti,am62-ecap-capture.yaml
counter: Introduce the COUNTER_COMP_ARRAY component type
counter: Consolidate Counter extension sysfs attribute creation
counter: Introduce the Count capture component
counter: 104-quad-8: Add Signal polarity component
counter: Introduce the Signal polarity component
counter: interrupt-cnt: Implement watch_validate callback
...
Make sure that the needed i2c functionality is supported during probe.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20220913073413.140475-3-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For reliable operation across the full range of supported
interface rates, the AD5593R needs a STOP condition between
address write, and data read (like show in the datasheet Figure 40)
so in turn i2c_smbus_read_word_swapped cannot be used.
While at it, a simple helper was added to make the code simpler.
Fixes: 56ca9db862 ("iio: dac: Add support for the AD5592R/AD5593R ADCs/DACs")
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220913073413.140475-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Using these newer macros allows the compiler to remove the unused
structure and functions when !CONFIG_PM_SLEEP + removes the need to
mark pm functions __maybe_unused.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220621202719.13644-16-jic23@kernel.org
