The capability for 802.11ac will soon be added to these drivers. Once
that is done, a bitmask will be too large for the data storage.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clearing IEEE80211_TX_CTL_PS_RESPONSE in a frame
that is not in the current context doesn't seem right.
Instead make sure that we don't add such frames
to the UAPSD queue by using a local variable.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason why frames marked with
IEEE80211_TX_CTL_TX_OFFCHAN have to be sent using
the UAPSD queue. Since mac80211 makes sure that
RoC is done before pushing an offchannel frame
to the driver, we can use the normal TX queues
for transmission.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we use IEEE80211_HW_QUEUE_CONTROL now, the
CAB/Offchannel queues are registered as the last
two queues. There is no need to check and reassign
the queues in the TX start()/done() routines.
CAB frames will not reach the tx() callback since
we set IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING and
pull the buffered frames during beacon transmission.
We also don't have a special HW queue for handling
off-channel frames.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Two bits control TX power on BBP_R1 register. Correct the mask,
otherwise we clear additional bit on BBP_R1 register, what can have
unknown, possible negative effect.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide ethtool support; with support for interrupt coalescing through
get_coalesce/set_coalesce.
Placeholders for begin/complete will be used by runtime PM
to make sure target is powered up while performing ethtool operations
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the driver to report signal strength information
to mac80211 for rtl8187se boards.
It differs from my previous RFT patch:
http://marc.info/?l=linux-wireless&m=140155388332534&w=2
because:
- I have now a working rtl8187se card, so I could serve my RFT by myself. :)
- CCK measurement code has changed a bit, but it does basically the same things.
- OFDM measurement method is changed because the older method reported incorrect
measures, at least for signals stronger than -40dBm).
CCK measurement seems quite good. OFDM seems less accurate, but this is the
same as the "reference" staging driver dose. I wanted not to change things just
to make measures of _one_ (my) card a bit more close to what _I_ (in my setup)
expected..
IMHO results are still good enough to justify reporting signal in dBm rather than in
"unspecified" units, so this is what this patch actually does.
Results of my tests with a working rtl8187se card connected with coaxes and
various RF attenuators to my AP are:
Input (approx) | CCK meas | OFDM meas
--------------------------------------
-30dBm | -32dBm | -31dBm
-40dBm | -40dBm | -41dBm
-50dBm | -50dBm | -55dBm
-60dBm | -59dBm | -63dBm
-70dBm | -69dBm | -73dBm
-80dBm | -79dBm | -83dBm
Also some real-field tests has been done (no coax, packets in the air) for the CCK
measure method, and they resulted in reasonable values.
Thanks-to: Bernhard Schiffner <bernhard@schiffner-limbach.de> [ for real-field tests]
Signed-off-by: andrea.merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When multiple channel contexts are enabled, a p2p interface
that is assigned to a context will have an address that
is different from the device mac address, which is used
by wpa_s as the p2p device ID.
Certain frames like provision requests use the device address
and these get dropped since ath9k_calculate_summary_state()
iterates over only the active interfaces in a context and the
device address is not used.
Fix this by adding the device mac address to the bssid mask.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for scan channel gap only when user_scan_in is not NULL.
user_scan_in is NULL for internal scans and if we check scan channel gap
at this place, it may result into crash.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the BSS information stored in mac80211 directly
is racy in certain conditions. For example, in a MCC
setup, if the scheduler is switching channels when
a local deauth is issued, calculation of the opmode/bssid
etc. is incorrect. To avoid this, store the bss params
in the driver and use it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AHB bus support was added in v2.6.38, through commit a0b907ee2a
("ath5k: Add AHB bus support."). That code can only be build if the
Kconfig symbol ATHEROS_AR231X is set. But that symbol has never been
added to the tree. So AHB bus support has always been dead code.
Let's remove all code that depends on ATHEROS_AR231X. If that symbol
ever gets added to the tree the AHB bus support can be re-added too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move iwl_mvm_max_scan_ie_len function to scan.c and fix the
implementation to conform with the LMAC scan API.
Since the correct implementation would leave us with unacceptably
tiny probes, add a workaround which returns a larger value.
In current implementation it's possible that unified_scan_lmac and
unified_sched_scan_lmac would return -ENOBUFS.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of traffic on multiple TIDs where one is aggregated
and the other is not RS would toggle between considering
traffic vs. the station as aggregated and not aggregated.
Instead consider the sta state as aggregated as long as
there's at least one TID aggregated.
This limitation is because the rates table is kept per
station and not per TID.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently BA notifications which don't reclaim any frames
would not cause the RS to be called as no skbs are passed
to mac80211. This is not optimal as RS can benefit from the
statistics of sent vs. acked of such a BA. This can improve the
reaction time of the RS algorithm. Also, an upcoming change in
the firmware would cause BA timeout to be reported as a BA notif
with 0 acked so this change is required for that as well.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 8000 HW series also includes the revision in the FW
name.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Align the trans->hw_rev variable format with previous series
format.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is a tradeoff between enabling better throughput for
bursty traffic and low latency. The number 6 was found to be
a good tradeoff for the Miracast use case which is the
major use case for low latency.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable RS to get updated directly via iwl_mvm_rs_tx_status
which will be called by the driver and not via mac80211
rate control. This is required for a following patch to
report on BAs which do not cause the BA window to progress.
Also this is a first step in decoupling rs from the
mac80211 rate control.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Improve the initial tx rate and antenna selection to be based on
the rssi of the last rx. This avoids starting at the lowest legacy
rate always and requiring more tx traffic to "climb" up the rates.
Since this option might cause trouble in certain setups, allow to
disable it by default.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As suggeested by checkpatch:
WARNING: Prefer ether_addr_copy() over memcpy() if the Ethernet addresses are __aligned(2)
In wmi.c I had to change due to sparse warnings copying of struct wmi_mac_addr
from form &cmd->peer_macaddr.addr to cmd->peer_macaddr.addr. In
ath10k_wmi_set_ap_ps_param() I also added the missing ".addr" to the copy
command.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Makes it more readable and fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/debug.c:593: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:594: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:595: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:596: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:597: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:599: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:600: WARNING: quoted string split across lines
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
ath10k/htc.c:49: WARNING: Possible unnecessary 'out of memory' message
ath10k/htc.c:810: WARNING: Possible unnecessary 'out of memory' message
ath10k/htt.h:1034: CHECK: Please use a blank line after function/struct/union/enum declarations
ath10k/htt_rx.c:135: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr
ath10k/htt_rx.c:173: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr
ath10k/pci.c:633: WARNING: macros should not use a trailing semicolon
ath10k/wmi.c:3594: WARNING: quoted string split across lines
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
WARNING: Missing a blank line after declarations
Please note that some of the cases I fixed by moving the variable declarations
to the beginning of the function, which is the preferred style in ath10k.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable pulse detection on extension channel if 40MHz channel width has been set
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This happens when CONFIG_ATH9K_CHANNEL_CONTEXT is
not enabled.
../drivers/net/wireless/ath/ath9k/recv.c: In function ‘ath_rx_ps_beacon’:
../drivers/net/wireless/ath/ath9k/recv.c:553:27: error: ‘struct ath_softc’ has no member named ‘offchannel’
if (sc->cur_chan == &sc->offchannel.chan)
^
../scripts/Makefile.build:257: recipe for target 'drivers/net/wireless/ath/ath9k/recv.o' failed
make[10]: *** [drivers/net/wireless/ath/ath9k/recv.o] Error 1
../scripts/Makefile.build:404: recipe for target 'drivers/net/wireless/ath/ath9k' failed
make[9]: *** [drivers/net/wireless/ath/ath9k] Error 2
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize neighbor linked list used by dynack to compute ACK timeout
as the maximum STA ACK timeout
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable ACK timeout estimation algorithm if set_coverage_class routine has been
called with negative coverage_class parameter. Dynack is automatically disabled
setting valid value for coverage class
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ack_to entry to debugfs in order to dump current ACK timeout value
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set control frame bit in rx filter if dynack processing has been activated
in order to enable ACK frame reception
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add sampling methods for ACK RX timestamp in ath_rx_tasklet() and for TX frame
timestamp in ath_tx_complete_aggr() and in ath_tx_process_buffer(). These
samples will be used in dynack processing for ACK timeout estimation
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not overwrite ACK timeout estimation in ath9k_hw_init_global_settings() if
dynack processing has been enabled
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ACK timeout estimation algorithm to ath9k Makefile and Kconfig
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add dynamic ACK timeout estimation algorithm based on ACK frame RX timestamp,
TX frame timestamp and frame duration.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Tested-by: Philippe Duchein <wireless-dev@duchein.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add duration field to ath_tx_status in order to report frame duration for each
entry in multi-retry chain. These fields will be used in ACK timeout estimation
algorithm (dynack)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove static keyword and export ath9k_hw_setslottime(),
ath9k_hw_set_ack_timeout() and ath9k_hw_set_cts_timeout() in hw.h.
These methods will be used in ACK timeout estimation algorithm (dynack)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the past when schedule scan was started while connected on one of
interfaces FW crashes were observed. In the newest FW this issue is
solved, so remove limitaion after examining corresponding TLV flag.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When read, this new debugfs entry requests the current temperature
from the firmware and outputs it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The scheduler is a HW sub-block that directs the work of the Flow
Handler by issuing requests for frame transfers, specifying source
and destination. Its primary function is to allocate flows into the
TX FIFOs based upon a pre-determined mapping.
The driver has some responsibilities to the scheduler, namely
initialising and maintaining the hardware registers. This is
currently done by directly accessing them, which can cause races
with the firmware also accessing the registers.
To address this problem, change the driver to no longer directly
access the registers but go through the firmware for this if the
firmware has support for DQA and thus the new command.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Set RRM_ENABLED (bit 6) flag in scan commands. When this flag is set
the fw will add WFA vendor-specific TPC report and DS parameter set
IEs into probe requests.
This bit is set for SCAN_OFFLOAD_REQUEST_CMD(0x51).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a ucode capability flag for support of Quiet Period (part of RRM).
If this flag is set, advertise device support.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
