Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.
This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.
Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.
Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.
[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we disassociate, it's not really useful to
send delBA action frames since we're going to send
disassoc/deauth anyway, so change that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, mac80211 uses the power constraint IE, and reduces
the regulatory max TX power by it. This can cause issues if
the AP is advertising a large power constraint value matching
a high TX power in its country IE, for example in this case:
...
Country: US Environment: Indoor/Outdoor
...
Channels [157 - 157] @ 30 dBm
...
Power constraint: 13 dB
...
What happened here is that our local regulatory TX power is
15 dBm, and gets reduced by 13 dB so we end up with only
2 dBm effective TX power, which is way too low.
Instead, handle the country IE/power constraint IE combined
and restrict our TX power to the max of the regulatory power
and the maximum power advertised by the AP, in this case
17 dBm (= 30 dBm - 13 dB).
Also print a message when this happens to let the user know
and help us debug issues with it.
Reported-by: Carl A. Cook <CACook@quantum-equities.com>
Tested-by: Carl A. Cook <CACook@quantum-equities.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move ieee80211_send_deauth_disassoc() to util.c to make it
available for the rest of the mac80211 code.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The power constraint IE is always a single byte
so check the size when parsing instead of later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Disconnect from the AP if channel switching in the
driver failed or if the new channel is unavailable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull in mac80211.git to let the next patch apply
without conflicts, also resolving a hwsim conflict.
Conflicts:
drivers/net/wireless/mac80211_hwsim.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ifmgd->bssid wasn't cleared properly in some
auth/assoc failure cases, causing mac80211 and
the low-level driver to go out of sync.
Clear ifmgd->bssid on failure, and notify the driver.
Cc: stable@kernel.org # 3.4+
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In multi-channel scenarios, the channel that we will
transmit a probe request on isn't always the current
channel (which will be NULL anyway) but will instead
be the channel that the AP is on. Pass the channel
to the ieee80211_send_probe_req() function so it can
be used in the different scenarios. The scan code
continues to pass the current channel, of course.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to declare the function in the
header file since it's only used in a single
place, so make it static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel switch IE has a fixed size, so we can
discard it in parsing if it's not the right size
and use the right struct pointer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The time until the channel switch is in TU,
not in milliseconds, so use TU_TO_EXP_TIME()
to correctly program the timer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clean up the CSA handling code by moving some
of it out of the if and using a C99 initializer
for the struct passed to the driver method.
While at it, also add a comment that we should
wait for a beacon after switching the channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a corner case that can happen when we
suspend with a timer running, then resume and
disconnect. If we connect again, suspend and
resume we might start timers that shouldn't be
running. Reset the timer flags to avoid this.
This affects both mesh and managed modes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When associating anew, the old station MLME flags should
be cleared. The only exception is the 40 MHz disable
flag as it might have been set while the channel was set
in a previous authentication attempt so it needs to be
kept intact.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sending probe requests, e.g. during software scanning,
these will go out on the *current* channel, so their IEs
need to be built from the current channel. At other times,
e.g. for beacons or probe request templates, the IEs will
be used on the *operating* channel and using the current
channel instead might result in errors.
Add the appropriate parameters to respect the difference.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using hw.conf.channel is wrong as it could be the
temporary channel if any function like the beacon
get function is called while scanning or during
other temporary out-of-channel activities.
Use oper_channel instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to set up the channel during auth
and again during assoc, just do it once. Currently
this doesn't result in any changes since calling
hw_config() with an unchanged channel will return
early, but with the channel context work this has
an impact on channel context assignment.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_prep_connection(), the station (if not NULL)
is the new station (representing the AP) that needs to be
added. Rename the variable to "new_sta" to clarify this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If HT/VHT isn't supported by us we shouldn't print
a message that we disabled it, do that only if the
AP didn't support WMM and we therefore disable it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, ps mode is indicated per device (rather than
per interface), which doesn't make a lot of sense.
Moreover, there are subtle bugs caused by the inability
to indicate ps change along with other changes
(e.g. when the AP deauth us, we'd like to indicate
CHANGED_PS | CHANGED_ASSOC, as changing PS before
notifying about disassociation will result in null-packets
being sent (if IEEE80211_HW_SUPPORTS_DYNAMIC_PS) while
the sta is already disconnected.)
Keep the current per-device notifications, and add
parallel per-vif notifications.
In order to keep it simple, the per-device ps and
the per-vif ps are orthogonal - the per-vif ps
configuration is determined only by the user
configuration (enable/disable) and the connection
state, and is not affected by other vifs state and
(temporary) dynamic_ps/offchannel operations
(unlike per-device ps).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This doesn't make any sense since we are expected to be on
the medium or at least to Tx only when we are on the right
channel and the AP/GO can hear us.
Move the call to mgd_prepare_tx() for deauth to be only
done in case we're sending a deauth while not associated.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the HW is monitoring connection loss (as advertised
by IEEE80211_HW_CONNECTION_MONITOR) but not filtering
beacons (IEEE80211_VIF_BEACON_FILTER) then mac80211 will
still start the beacon loss timer and if a few beacons
are lost, e.g. due to scanning, drop the connection.
If the hardware doesn't advertise connection monitoring,
then it won't drop the connection right away but probe
the AP, which is intended, but due to the logic in the
timer when connection monitoring is done it assumes the
connection was actually lost.
Fix this problem by not starting the timer when the HW
does connection monitoring.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Insert VHT IEs into association frames to allow
mac80211 to connect as a VHT client.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
[clarify commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
on disassoc, ieee80211_set_disassoc() goes out of PS
before indicating BSS_CHANGED_ASSOC (not sure why this
is needed, but some drivers might count on the current
behavior).
However, it does it after sending the disassoc
frame, which results in null-data frame being sent
(in order to go out of ps) after we were already sent
the disassoc, which is invalid.
Fix it by going out of ps before sending the disassoc.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers (iwlegacy, iwlwifi and rt2x00) today use the
bss_conf.last_tsf value. By itself though that value is
completely worthless since it may be ancient. What really
is needed is synchronisation between some device time and
the TSF.
To clarify this, rename bss_conf.last_tsf to sync_tsf and
add sync_device_ts which is obtained from rx_status which
gets a new field device_timestamp for this purpose. This
is intentionally not using the mactime field since that
is used for other things and in IBSS is expected to sync
with the IBSS's TSF which isn't necessarily true for the
device timestamp.
Also, since we have the information and it's useful even
before the connection has been established, give all the
timing details to the driver before authenticating.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If association failed due to internal error (e.g. no
supported rates IE), we call ieee80211_destroy_assoc_data()
with assoc=true, while we actually reject the association.
This results in the BSSID not being zeroed out.
After passing assoc=false, we no longer have to call
sta_info_destroy_addr() explicitly. While on it, move
the "associated" message after the assoc_success check.
Cc: stable@vger.kernel.org [3.4+]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_mlme_notify_scan_completed() iterates all
interfaces and doesn't need to assign anything to
the sdata variable before the loop.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the AC parameters change, drivers might rely
on getting a bss_info_changed notification with
BSS_CHANGED_QOS in addition to the conf_tx call.
Always call the function when userspace updates
are made (in AP/GO modes) and also set the change
flag when updates were made by the AP (in managed
mode.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers require setup before being able to send
management frames in managed mode, in particular in
multi-channel cases.
Introduce API to allow the drivers to do such setup
while being able to sleep waiting for the setup to
finish in the device. This isn't possible inside the
TX call since that can't sleep.
A future patch may also restructure the TX retry to
wait for the driver to report the frame status, as
suggested by Arik in
http://mid.gmane.org/CA+XVXffKSEL6ZQPQ98x-zO-NL2=TNF1uN==mprRyUmAaRn254g@mail.gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers might need getting the probe request
(e.g. in order to extract the ssid) even during
auth/assoc.
Make ieee80211_ap_probereq_get() support it
by considering auth_data/assoc_data as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
beacon_ies is needed only in order to extract the dtim
period. However, even if it's missing we can still enter
ps with dtim=1 (which also happens if the TIM ie is invalid).
Most drivers don't use conf.max_sleep_period/ps_dtim_period
anyway, and this check prevents them from entering ps if
they don't have beacon (but only probe response), even though
the beacon is not needed at all.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On deauth/disassoc we tear down all BA sessions. These
DELBA packets are sent on the appropriate TID, while
deauth/disassoc is always sent on VO. This sometimes
ends with the DELBA being sent after the deauth was
already sent.
Fix it by flushing all the pending frames before
sending deauth/disassoc.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
* a lot of messages should be pr_info, not pr_debug
* wholesale use of pr_debug makes it require *both*
Kconfig and dynamic configuration
* there are still a lot of ifdefs
* the style is very inconsistent, sometimes the
sdata->name is printed in front
Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_set_disassoc() clears ifmgd->bssid before
building DELBA frames, resulting in frames with invalid
bssid ("00:00:00:00:00:00").
Fix it by clearing ifmgd->bssid only after building
all the needed frames.
After this change, we no longer need to save the
bssid (before clearing it), so remove the local array.
Reported-by: Ido Yariv <ido@wizery.com>
Cc: stable@vger.kernel.org
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Save and configure the wmm_acm per sdata, rather than
per hardware.
If wmm_acm is saved per hardware when running two
interfaces simultaneously on the same hardware one
interface's wmm policy will be affected by the other
interface.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If an AP is beaconing with different capabilities than the one we get
in the associate response, we were still using the capabilities
received in the beacons. One example is when the AP is beaconing with
the short slot bit set to zero and then we try to connect to it with
long slot. In this case, we would keep using long slot until the next
beacon was received.
Fix this by using the correct capability value when calling
ieee80211_handle_bss_capability(). We were using cbss->capability,
but we should use the bss_conf->assoc_capability instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some compilers (eg. gcc 4.4.1 for ARM) report a false positive warning
in mlme.c:
net/mac80211/mlme.c: In function 'ieee80211_prep_connection':
net/mac80211/mlme.c:3035: warning: 'sta' may be used uninitialized in this function
This is a false positive because the place where 'sta' is used is
inside an if with the same condition of where it is set:
[...]
if (!have_sta) {
sta = sta_info_alloc(sdata, cbss->bssid, GFP_KERNEL);
if (!sta)
return -ENOMEM;
}
[...]
if (!have_sta) {
[...]
sta->sta.supp_rates[cbss->channel->band] = rates;
[...]
For some reason the compiler doesn't understand this and warns.
While this is not a problem in the code itself, we can avoid polluting
the build logs with false positives by setting sta to NULL on
declaration and checking for sta instead of !have_sta in the second if.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stop connection monitor poll during disassociation.
This clears the polling flags and if a scan was
deferred it will be run.
Without this fix, if a scan was deferred due to
connection monitoring while disassociation happens,
this scan blocks further scan requests until interface
down/up which causes problems connecting to another AP.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
