* Use 'hwif->dma_base + {4,8}' instead of hwif->dma_prdtable in
{ide,scc}_dma_setup().
* Remove no longer needed ->dma_prdtable field from ide_hwif_t.
While at it:
* Use ATA_DMA_TABLE_OFS define.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use 'hwif->dma_base + {1,3}' instead of hwif->dma_vendor{1,3} in
pdc202xx_new host driver.
* Remove no longer needed ->dma_vendor{1,3} fields from ide_hwif_t.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->dma_host_set and ->dma_start methods (+ __scc_dma_end() helper)
so scc_ide_{in,out}b() can be used directly.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Skip "VLB sync" in ata_{in,out}put_data() if host uses MMIO.
* Use I/O ops directly in ata_vlb_sync() an drop no longer needed
'ide_drive_t *drive' argument.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_pad_transfer() helper (which uses ->{in,out}put_data methods
internally so the transfer is also padded to drive+host requirements)
and use it instead of ide_atapi_{write_zeros,discard_data}().
* Remove no longer needed ide_atapi_{write_zeros,discard_data}().
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove no longer used ->INW and ->OUTW methods.
While at it:
* scc_pata.c: scc_ide_{out,in}w() is called only in scc_tf_{load,read}()
so inline it there.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_read method so out{b,w}(), in{b,w}() and superio_ide_inb()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_{load,read} methods so scc_ide_{outb,outw,inb,inw}()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_{load,read} methods so outb()/inb() and mm_outw()/mm_inw()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_{load,read} methods so cris_ide_{outb,outw,inb,inw}()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->tf_load and ->tf_read methods to ide_hwif_t and set the default
methods in default_hwif_transport().
* Use ->tf_{load,read} instead o calling ide_tf_{load,read}() directly.
* Make ide_tf_{load,read}() static.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out debugging code from ide_tf_load() to ide_tf_dump() helper
and update ide_tf_load() users accordingly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_execute_pkt_cmd() helper for executing PACKET command,
then convert ATAPI device drivers to use it.
As a nice side-effect this fixes ide-{floppy,tape,scsi} w.r.t.
ide_lock taking (ide-cd was OK).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Always use ->OUTBSYNC method for executing commands so the posting is done
if needed (this affects only pmac and scc_pata host drivers at the moment).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* proc_reports_siimage() is now only called by init_chipset_siimage()
so inline it there.
* Use array instead of switch statement for reporting clock modes.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add sil_iowrite{8,16,32}() and sil_ioread{8,16}() helpers, then use them to
merge code accessing configuration registers through PCI and MMIO together.
[ because of this SATA initialization bits from setup_mmio_siimage() are
moved to init_chipset_siimage() ]
This also cuts code size a bit:
text data bss dec hex filename
4437 164 0 4601 11f9 drivers/ide/pci/siimage.o.before
3979 164 0 4143 102f drivers/ide/pci/siimage.o.after
While at it:
* Use I/O ops directly instead of using ->IN{B,W} and ->OUT{B,W}.
* Fixup CodingStyle in setup_mmio_siimage().
* Rename 'tmpbyte' variable to 'tmp' in init_chipset_siimage().
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Do clocking register posting earlier in setup_mmio_siimage()
to match code in init_chipset_siimage().
This is a preparation for the next patch which merges PCI and MMIO
code paths together.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ins{w,l}()/outs{w,l}() and __ide_mm_ins{w,l}()/__ide_mm_outs{w,l}()
directly in ata_{in,out}put_data() (by using IDE_HFLAG_MMIO host flag to
decide which I/O ops are required).
* Remove no longer needed ->INS{W,L} and ->OUTS{W,L} methods (ide-h8300,
au1xxx-ide and scc_pata implement their own ->{in,out}put_data methods).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_MMIO host flag and set it for hosts which use
default_hwif_mmiops().
v2:
* Fix kernel panic in pmac host driver (',' should be '|').
Thanks to Kamalesh for reporting it + testing the fix
and to Andrew for hinting me about the source of the issue.
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
v2:
* Update ->{in,out}_data methods to take 'struct request *rq' argument.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
v2:
* Update ->{in,out}_data methods to take 'struct request *rq' argument.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
v2:
* Update ->{in,out}_data methods to take 'struct request *rq' argument
(thanks to Stephen Rothwell for catching it).
There should be no functional changes caused by this patch.
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Merge ->atapi_{in,out}put_bytes and ->ata_{in,out}put_data methods
into new ->{in,out}put_data methods which take number of bytes to
transfer as an argument and always do padding.
While at it:
* Use 'hwif' or 'drive->hwif' instead of 'HWIF(drive)'.
There should be no functional changes caused by this patch (all users
of ->ata_{in,out}put_data methods were using multiply-of-4 word counts).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->atapi_{in,out}put_bytes and ->ata_{in,out}put_data methods to
falconide and q40ide host drivers (->ata_* methods are implemented on
top of ->atapi_* methods so they also do byte-swapping now).
* Cleanup atapi_{in,out}put_bytes().
v2:
* Add 'struct request *rq' argument to ->ata_{in,out}put_data methods
and don't byte-swap disk fs requests (we shouldn't un-swap fs requests
because fs itself is stored byte-swapped on the disk) - this is how
things were done before the patch (ideally device mapper should be
used instead but it would break existing setups and would have some
performance impact).
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Richard Zidlicky <rz@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Monday 28 April 2008, Sergei Shtylyov wrote:
> Hello, I wrote:
>
> > Fix these warnings emitted when compiling drivers/ide/mips/au1xxx-ide.c:
>
> > include/asm/mach-au1x00/au1xxx_ide.h:137: warning: 'auide_tune_drive' declared
> > `static' but never defined
> > include/asm/mach-au1x00/au1xxx_ide.h:138: warning: 'auide_tune_chipset' declared
> > `static' but never defined
>
> > by wiping out the whole "function prototyping" section from the header file
> > <asm-mips/mach-au1x00/au1xxx_ide.h> as it mostly declared functions that are
> > already dead in the IDE driver; move the only useful prototype into the driver.
> >
> > Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
>
> > ---
> > I'm not sure thru which tree this should go -- probably thru Linux/MIPS one...
>
> > Bart, au1xxx-ide-fix-mwdma-support.patch will probably need to be updated to
> > remove that added prototype since it won't be needed anymore...
>
> Which you haven't done either in that patch or in
> au1xxx-ide-use-init_dma-method.patch. So, face the consequences:
>
> drivers/ide/mips/au1xxx-ide.c:456: error: conflicting types for 'auide_ddma_init'
> drivers/ide/mips/au1xxx-ide.c:51: error: previous declaration of
> 'auide_ddma_init' was here
> drivers/ide/mips/au1xxx-ide.c:456: error: conflicting types for 'auide_ddma_init'
> drivers/ide/mips/au1xxx-ide.c:51: error: previous declaration of
> 'auide_ddma_init' was here
> drivers/ide/mips/au1xxx-ide.c:51: warning: 'auide_ddma_init' used but never
> defined
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This bug was introduced in the 2.6.24 i386/x86_64 tree merge, where
MSI-X vector allocation will eventually fail. The cause is the new
bit array tracking used vectors is not getting cleared properly on
IRQ destruction on the 32-bit APIC code.
This can be seen easily using the ixgbe 10 GbE driver on multi-core
systems by simply loading and unloading the driver a few times.
Depending on the number of available vectors on the host system, the
MSI-X allocation will eventually fail, and the driver will only be
able to use legacy interrupts.
I am generating the same patch for both stable trees for 2.6.24 and
2.6.25.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bitops source file was renamed, so fix docbook for that.
docproc: linux-2.6.25-git11/include/asm-x86/bitops_32.h: No such file or directory
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
SELinux: Fix a RCU free problem with the netport cache
SELinux: Made netnode cache adds faster
SELinux: include/security.h whitespace, syntax, and other cleanups
SELinux: policydb.h whitespace, syntax, and other cleanups
SELinux: mls_types.h whitespace, syntax, and other cleanups
SELinux: mls.h whitespace, syntax, and other cleanups
SELinux: hashtab.h whitespace, syntax, and other cleanups
SELinux: context.h whitespace, syntax, and other cleanups
SELinux: ss/conditional.h whitespace, syntax, and other cleanups
SELinux: selinux/include/security.h whitespace, syntax, and other cleanups
SELinux: objsec.h whitespace, syntax, and other cleanups
SELinux: netlabel.h whitespace, syntax, and other cleanups
SELinux: avc_ss.h whitespace, syntax, and other cleanups
Fixed up conflict in include/linux/security.h manually
* endianness annotations
* endianness fixes
* missing get_unaligned/put_unaligned
It's pretty much all over the place, changes to different files are independent.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Serial-parts-Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
usb_control_msg() converts arguments to little-endian itself,
doing that in caller means breakage on big-endian boxen.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
psr is not a good name for local variable in macro body when it
has a good chance of being the argument of said macro (actually
is at least in one place)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* EXTRA_CFLAGS do not apply for *.S
* don't bother with symlinks to ../lib/mem*.S, just add ../lib/mem*.o
to object list
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
iwlwifi: Allow building iwl3945 without iwl4965.
wireless: Fix compile error with wifi & leds
tcp: Fix slab corruption with ipv6 and tcp6fuzz
ipv4/ipv6 compat: Fix SSM applications on 64bit kernels.
[IPSEC]: Use digest_null directly for auth
sunrpc: fix missing kernel-doc
can: Fix copy_from_user() results interpretation
Revert "ipv6: Fix typo in net/ipv6/Kconfig"
tipc: endianness annotations
ipv6: result of csum_fold() is already 16bit, no need to cast
[XFRM] AUDIT: Fix flowlabel text format ambibuity.
this option has been the default on a wide range of distributions
for a long time - time to make it non-experimental.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since both the IDE interface and SMC 91C111 Ethernet chip are on-board
devices, not SOC devices, move the platform device registration form the
common to the board specific code.
While at it, remove semicolon (which didn't break compilation only by
chance) from the AU1XXX_ATA_DDMA_REQ macro and do some renaming:
- change 'au1200_ide0_' variable name prefix to the mere 'ide_';
- change 'smc91x_' variable name prefix to 'smc91c111_' since that's the
name of the chip used on the boards;
- drop 'AU1XXX_' prefix from the names of macros describing IDE and Ethernet
on-board devices;
- change 'SMC91111_' to 'SMC91C111_', change 'IRQ' to 'INT' in the names of
the macros describing the Ethernet chip for consistency with the IDE
macros;
- change 'ATA_' to 'IDE_' and 'OFFSET' to 'SHIFT' (since this value is
indeed a shift count) in the names of the macros describing the IDE
interface.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pb1200 does have SMC 91C111 Ethernet chip on board but the platform code
did not register it, so one couldn't mount NFS...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The on-board SMC 91C111 chip only decodes 16 bytes of memory (obviously, it
can not decode a whole megabyte starting from address 0x19000300).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
