This patch removes the GLF_NOCACHE flag from the glocks associated with
flocks. There should be no good reason not to cache glocks for flocks:
they only force the glock to be demoted before they can be reacquired,
which can slow down performance and even cause glock hangs, especially
in cases where the flocks are held in Shared (SH) mode.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch allows flock glocks to use a non-blocking dequeue rather
than dq_wait. It also reverts the previous patch I had posted regarding
dq_wait. The reverted patch isn't necessarily a bad idea, but I decided
this might avoid unforeseen side effects, and was therefore safer.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Normally GFP_KERNEL is ok here, but there is now a rarely used code path
relating to deallocation of unlinked inodes (in certain corner cases)
which if hit at times of memory shortage can cause recursion while
trying to free memory.
One solution would be to try and move the gfs2_glock_get() call so
that it is no longer called while another glock is held, but that
doesn't look at all easy, so GFP_NOFS is the best solution for the
time being.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
We must not leave items on the LRU list with GLF_LOCK set, since
they can be removed if the glock is brought back into use, which
may then potentially result in a hang, waiting for GLF_LOCK to
clear.
It doesn't happen very often, since it requires a glock that has
not been used for a long time to be brought back into use at the
same moment that the shrinker is part way through disposing of
glocks.
The fix is to set GLF_LOCK at a later time, when we already know
that the other locks can be obtained. Also, we now only release
the lru_lock in case a resched is needed, rather than on every
iteration.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Function gfs2_glock_dq_wait is supposed to dequeue a glock and then
wait for the lock to be demoted. The problem is, if this is a shared
lock, its demote will depend on the other holders, which means you
might end up waiting forever because the other process is blocked.
This problem is especially apparent when dealing with nested flocks.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The i.MX6 reference manual doesn't make a clear distinction
between the fixed clock divider and the enable gate for the
pcie and sata reference clocks. This lead to the lvds mux
inputs in the imx6q clk driver to be parented from the
ref clock (which is the divider) instead of the actual gate,
which in turn prevents the upstream clock to actually be
enabled when lvds clk out is active.
This fixes a hard machine hang regression in kernel 3.16 for
boards where only pcie is active but no sata, as with this
kernel version the imx6-pcie driver is no longer enabling
the upstream clock directly but only lvds clk out.
Reported-by: Arne Ruhnau <arne.ruhnau@target-sg.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Arne Ruhnau <arne.ruhnau@target-sg.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
We should schedule the 5s "timer work" before starting the data transfer,
otherwise, the data transfer code may finish so fast on another
virtual cpu that when the code(fcopy_write()) trying to cancel the 5s
"timer work" can occasionally fail because the "timer work" may haven't
been scheduled yet and as a result the fcopy process will be aborted
wrongly by fcopy_work_func() in 5s.
Thank Liz Zhang <lizzha@microsoft.com> for the initial investigation
on the bug.
This addresses https://bugzilla.redhat.com/show_bug.cgi?id=1118123
Tested-by: Liz Zhang <lizzha@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* pm-sleep:
PM / sleep: fix freeze_ops NULL pointer dereferences
PM / sleep: Fix request_firmware() error at resume
* pm-cpufreq:
cpufreq: make table sentinel macros unsigned to match use
cpufreq: move policy kobj to policy->cpu at resume
cpufreq: cpu0: OPPs can be populated at runtime
cpufreq: kirkwood: Reinstate cpufreq driver for ARCH_KIRKWOOD
cpufreq: imx6q: Select PM_OPP
cpufreq: sa1110: set memory type for h3600
Commit 5eeaf1f189 (cpufreq: Fix build error on some platforms that
use cpufreq_for_each_*) moved function cpufreq_next_valid() to a public
header. Warnings are now generated when objects including that header
are built with -Wsign-compare (as an out-of-tree module might be):
.../include/linux/cpufreq.h: In function ‘cpufreq_next_valid’:
.../include/linux/cpufreq.h:519:27: warning: comparison between signed
and unsigned integer expressions [-Wsign-compare]
while ((*pos)->frequency != CPUFREQ_TABLE_END)
^
.../include/linux/cpufreq.h:520:25: warning: comparison between signed
and unsigned integer expressions [-Wsign-compare]
if ((*pos)->frequency != CPUFREQ_ENTRY_INVALID)
^
Constants CPUFREQ_ENTRY_INVALID and CPUFREQ_TABLE_END are signed, but
are used with unsigned member 'frequency' of cpufreq_frequency_table.
Update the macro definitions to be explicitly unsigned to match their
use.
This also corrects potentially wrong behavior of clk_rate_table_iter()
if unsigned long is wider than usigned int.
Fixes: 5eeaf1f189 (cpufreq: Fix build error on some platforms that use cpufreq_for_each_*)
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When using USB 3.0 pen drive with the [AMD] FCH USB XHCI Controller
[1022:7814], the second hotplugging will experience the USB 3.0 pen
drive is recognized as high-speed device. After bisecting the kernel,
I found the commit number 41e7e056cd
(USB: Allow USB 3.0 ports to be disabled.) causes the bug. After doing
some experiments, the bug can be fixed by avoiding executing the function
hub_usb3_port_disable(). Because the port status with [AMD] FCH USB
XHCI Controlleris [1022:7814] is already in RxDetect
(I tried printing out the port status before setting to Disabled state),
it's reasonable to check the port status before really executing
hub_usb3_port_disable().
Fixes: 41e7e056cd (USB: Allow USB 3.0 ports to be disabled.)
Signed-off-by: Gavin Guo <gavin.guo@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few more fixes for 3.16. The pageflipping fixes I dropped last week
have finally shaped up so this is mostly fixes for fallout from the
pageflipping code changes. Also fix a memory leak and a black screen
when restoring the backlight on console unblanking.
* 'drm-fixes-3.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Make classic pageflip completion path less racy.
drm/radeon: Add missing vblank_put in pageflip ioctl error path.
drm/radeon: Remove redundant fence unref in pageflip path.
drm/radeon: Complete page flip even if waiting on the BO fence fails
drm/radeon: Move pinning the BO back to radeon_crtc_page_flip()
drm/radeon: Prevent too early kms-pageflips triggered by vblank.
drm/radeon: set default bl level to something reasonable
drm/radeon: avoid leaking edid data
Fixed error introduced in commit id 7730b4c (" cxgb4/iw_cxgb4: work request
logging feature") while compiling on 32 bit architecture reported by kbuild.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 methods for ZLP (zero-length packet) generation:
1) In software
2) Automatic generation by device controller
1) is implemented in UDC driver and it attaches ZLP to IN packet if
descriptor->size < wLength
2) can be enabled/disabled by setting ZLT bit in the QH
When gadget ffs is connected to ubuntu host, the host sends
get descriptor request and wLength in setup packet is 255 while the
size of descriptor which will be sent by gadget in IN packet is
64 byte. So the composite driver sets req->zero = 1.
In UDC driver following code will be executed then
if (hwreq->req.zero && hwreq->req.length
&& (hwreq->req.length % hwep->ep.maxpacket == 0))
add_td_to_list(hwep, hwreq, 0);
Case-A:
So in case of ubuntu host, UDC driver will attach a ZLP to the IN packet.
ubuntu host will request 255 byte in IN request, gadget will send 64 byte
with ZLP and host will come to know that there is no more data.
But hold on, by default ZLT=0 for endpoint 0 so hardware also tries to
automatically generate the ZLP which blocks enumeration for ~6 seconds due
to endpoint 0 STALL, NAKs are sent to host for any requests (OUT/PING)
Case-B:
In case when gadget ffs is connected to Apple device, Apple device sends
setup packet with wLength=64. So descriptor->size = 64 and wLength=64
therefore req->zero = 0 and UDC driver will not attach any ZLP to the
IN packet. Apple device requests 64 bytes, gets 64 bytes and doesn't
further request for IN data. But ZLT=0 by default for endpoint 0 so
hardware tries to automatically generate the ZLP which blocks enumeration
for ~6 seconds due to endpoint 0 STALL, NAKs are sent to host for any
requests (OUT/PING)
According to USB2.0 specs:
8.5.3.2 Variable-length Data Stage
A control pipe may have a variable-length data phase in which the
host requests more data than is contained in the specified data
structure. When all of the data structure is returned to the host,
the function should indicate that the Data stage is ended by
returning a packet that is shorter than the MaxPacketSize for the
pipe. If the data structure is an exact multiple of wMaxPacketSize
for the pipe, the function will return a zero-length packet to indicate
the end of the Data stage.
In Case-A mentioned above:
If we disable software ZLP generation & ZLT=0 for endpoint 0 OR if software
ZLP generation is not disabled but we set ZLT=1 for endpoint 0 then
enumeration doesn't block for 6 seconds.
In Case-B mentioned above:
If we disable software ZLP generation & ZLT=0 for endpoint then enumeration
still blocks due to ZLP automatically generated by hardware and host not needing
it. But if we keep software ZLP generation enabled but we set ZLT=1 for
endpoint 0 then enumeration doesn't block for 6 seconds.
So the proper solution for this issue seems to disable automatic ZLP generation
by hardware (i.e by setting ZLT=1 for endpoint 0) and let software (UDC driver)
handle the ZLP generation based on req->zero field.
Cc: stable@vger.kernel.org
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Huawei's usage of the subclass and protocol fields is not 100%
clear to us, but there appears to be a very strict system.
A device with the "shared" device ID 12d1:1506 and this NCM
function was recently reported (showing only default altsetting):
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 3
bInterfaceProtocol 22
iInterface 8 CDC Network Control Model (NCM)
** UNRECOGNIZED: 05 24 00 10 01
** UNRECOGNIZED: 06 24 1a 00 01 1f
** UNRECOGNIZED: 0c 24 1b 00 01 00 04 10 14 dc 05 20
** UNRECOGNIZED: 0d 24 0f 0a 0f 00 00 00 ea 05 03 00 01
** UNRECOGNIZED: 05 24 06 01 01
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 9
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two device IDs found in an out-of-tree driver downloadable
from Netgear.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement per channel software TX and RX packet counters
accessed as ethtool statistics.
This allows confirmation with MAC statistics.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If "newmtu * 2 + 4" is too large then it can cause an integer overflow
leading to memory corruption. Eric Dumazet suggests that 65534 is a
reasonable upper limit.
Btw, "newmtu" is not allowed to be a negative number because of the
check in dev_set_mtu(), so that's ok.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla says:
====================
be2net: patch set
Patches 1 to 6 address issues with return values of some ndo/ethtool
driver methods. In error scenarios, either an inappropriate error or
a +ve return value (where the stack expects a -ve value) was being returned.
Patch 7 updates description strings for certain UE bits.
Patch 8 cleans up (reduces) argument passing for a few routines in be_cmds.c.
Patch 9 removes some unused code (unused definitions.)
Patch 10 updates NULL check in the driver to a consistent "if (!foo)" style.
Patchs 11 to 13 fix a few minor issues with the earlier patch bec84e6
("create optimal number of queues on SR-IOV config"):
- patch 11 fixes BEx_get_resources() code to use be_max_vfs() macro
- patch 12 skips SR-IOV config code for BE2 that doesn't support SRIOV
- patch 13 uses adapter->flags to track SRIOV enabled state
Patch 14 updates the driver version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver so far used adapter->num_vfs value to check if SR-IOV is enabled
or not. But, the patch bec84e6("create optimal number of queues on SR-IOV
config") changed this logic. The adapter->num_vfs value is validated and set
much before SR-IOV is enabled. So, we now use an explicit flag to track
SR-IOV enabled state.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As SRIOV is not supported on BE2 chip, avoid calling be_get/set_sriov_config()
for BE2 chip.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
max-vfs value must be accessed via the macro be_max_vfs(adapter).
The earlier patch "create optimal number of queues on SR-IOV config"
by mistake, did not use this macro. This patch fixes it.
fixes: bec84e6b ("be2net: create optimal number of queues on SR-IOV config")
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "if (foo == NULL)" statements with "if (!foo)" to be consistent
across the driver.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pointer to adapter struct is passed anyway to all of the FW-cmd routines
in be_cmds.c. For routines which query data from FW, the adapter pointer
is enough to return the queried fields.
There is no need to separately pass pointers to individual members of
the adapter structure. This patch fixes this for be_cmd_get_fw_ver()
and be_cmd_get_fw_cfg() routines.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates some description strings for BEx/Skyhawk-R
UE (unrecoverable error) status register bits. The appropriate strings
are logged when a UE is detected in the adapter.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netlink layer expects a -ve status value to be returned when a driver
ndo method encounters an error. The driver was directly passing the
error status returned by FW (a positive value) to the stack.
This patch fixes this by returning -EIO status when a FW-cmd reports an error.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool expects a -ve status value to be returned when a driver method
encounters an error. The driver was directly passing the
error status returned by FW (a positive value) to ethtool.
This patch fixes this by returning -EIO status in cases where FW returns
an error.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the FW stops responding with completions, return -ETIMEDOUT error
(instead of -1) to the stack.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For FW download ethtool cmd, if the user provides an FW-image incompatible
with the chip, return -EINVAL instead of -1.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating VF's tx-rate and FW-download are not allowed when the interface is
down. In such cases return -ENETDOWN to the stack.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we might arrive to bond_net_exit() with some bonds left (that
were created while the module is unloading). We take care of that by
destroying sysfs (the last possibility to add new bonds) and then
destroying all the remaining bonds.
However, we destroy the /proc/net/bonding directory before destroying those
last bonds, and get a warning that we're trying to destroy a non-empty
proc directory (containing /proc/net/bonding/bondX).
Fix this by moving bond_destroy_proc_dir() after all the bonds are
destroyed, so that we're sure that no bonds exist.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it's always called with RTNL held, via dev_set_allmulti/promiscuity.
Also, remove the wrong comment.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anish Bhatt says:
====================
cxgb4i: Add ipv6 support
The following patchset add ipv6 support for the cxgb4i(iscsi) driver.
Patch 1 moves a define from the iw_cxgb4 to cxgb4 to prevent code duplication,
as it is used by cxgb4i and iw_cxgb4 both.
Patch 2 exports symbols needed by cxgb4i for ipv6 support from cxgb4.
Patch 3 & 4 deal with actual ipv6 code in libcxgbi/cxgb4i.
Submitting to net-next as changes were needed in cxgb4/iw_cxgb4, and submitting
to scsi separately would break compilation, cc-ing scsi & rdma.
v2 : Cleanup macro that prints ip addresses by using %pIS in patch 3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This define is used by cxgb4i and iw_cxgb4, moving to avoid code duplication
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the Layer 2 hash factors with packet type ID field.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: David S. Miller <davem@davemloft.net>
CC: Pan Jiafei <Jiafei.Pan@freescale.com>
Signed-off-by: Jianhua Xie <jianhua.xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current L2 hash helper calculates destination eth addr and
source ether addr as L2 hash factors. This patch is adding
packet type ID field into L2 hash factors. While one of
BOND_XMIT_POLICY_LAYER2 or BOND_XMIT_POLICY_{LAYER|ENCAP}23
is applied, for the 2nd level hash, enhanced hash method can
help to distribute different types of packets like IPv4/IPv6
packets to different slave devices.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: David S. Miller <davem@davemloft.net>
CC: Pan Jiafei <Jiafei.Pan@freescale.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jianhua Xie <jianhua.xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: fixed issue with checking return of dcbnl_rtnl_ops->getapp()
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like other places, we need to cancel the nest attribute after
we start. Fortunately the netlink message will not be sent on
failure, so it's not a big problem at all.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fixes console deadlock when resuming PV guests
- Fix regression hit when ballooning and resuming PV guests
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTxt1pAAoJEFjIrFwIi8fJbGcH/RW88DhFw3wJrtyd68R2uY4R
BQVsUeXltzS7cRZ46ytStn+UveXOII9SI1kdU0yAPWbpzgKwXkXLTGUbL26vXmfq
ZpAGIVFBG+SrHuTDEYP/IhB2TI6ugTeHVK8+Mo+HfjEs99OJ+BAf4IlZ9cLUvrW8
l51HcFe7c9ueH7YculTAesUWZrdS6p5FBbTz0pwG8BvU5NxJ2EC+MktLEKZmV27Q
Y3CN///BhIN6YXhPA3Frykxs36m4gFJUPgXbEQFea79I67f+frBX/VdKNPeaMoaR
yb305PStdxwo6Ja8Qx/CrTl+y8vTtLP1cADRGSdLD3m1vI42PNF4Qjr1ruLbA34=
=ky5L
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.16-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from Konrad Rzeszutek Wilk:
"Two fixes found during migration of PV guests. David would be the one
doing this pull but he is on vacation.
Fixes:
- fix console deadlock when resuming PV guests
- fix regression hit when ballooning and resuming PV guests"
* tag 'stable/for-linus-3.16-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: set ballooned out pages as invalid in p2m
xen/manage: fix potential deadlock when resuming the console
I was cleaning out my INBOX and found two fixes from zhangwei from
a year ago that were lost in my mail. These fix an inconsistency between
trace_puts() and the way trace_printk() works. The reason this is
important to fix is because when trace_printk() doesn't have any
arguments, it turns into a trace_puts(). Not being able to enable a
stack trace against trace_printk() because it does not have any arguments
is quite confusing. Also, the fix is rather trivial and low risk.
While porting some changes to PowerPC I discovered that it still has
the function graph tracer filter bug that if you also enable stack tracing
the function graph tracer filter is ignored. I fixed that up.
Finally, Martin Lau, fixed a bug that would cause readers of the
ftrace ring buffer to block forever even though it was suppose to be
NONBLOCK.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTxfAHAAoJEKQekfcNnQGueDkH/jQ/FgNPw+GbKuNpZwWqMQds
ivGM8yb6NgmlDQx60oBOL9TduKN2LCqW3HWDoyzduSozuLUxpRTPWtVThKo0Q9Fp
FPHWewdrX7DwWkyEqeG7FAAhjqPedgEZoDOwy7BArzJYpHcpex42trDY4BhjPrlM
ESA+/M+Xm1vGCJzcNSqNHYE/mF/tHptdM1mlLZ3g9ql49MiTbQxEMbHX7lih24sv
AzNP1SlisYN5CkX4hbRGhCYkZdmdVZt/xiyBAQRWCGFx+jsdJbMXDJnevDCdU9Mv
GNtKwqsi1/GeE5nvKxZyQKsDEE98Pd8LyQ0kDqKpAfTutqNE4mpWJkCxUqTmE4Q=
=aFqO
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.16-rc5-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"A few more fixes for ftrace infrastructure.
I was cleaning out my INBOX and found two fixes from zhangwei from a
year ago that were lost in my mail. These fix an inconsistency
between trace_puts() and the way trace_printk() works. The reason
this is important to fix is because when trace_printk() doesn't have
any arguments, it turns into a trace_puts(). Not being able to enable
a stack trace against trace_printk() because it does not have any
arguments is quite confusing. Also, the fix is rather trivial and low
risk.
While porting some changes to PowerPC I discovered that it still has
the function graph tracer filter bug that if you also enable stack
tracing the function graph tracer filter is ignored. I fixed that up.
Finally, Martin Lau, fixed a bug that would cause readers of the
ftrace ring buffer to block forever even though it was suppose to be
NONBLOCK"
This also includes the fix from an earlier pull request:
"Oleg Nesterov fixed a memory leak that happens if a user creates a
tracing instance, sets up a filter in an event, and then removes that
instance. The filter allocates memory that is never freed when the
instance is destroyed"
* tag 'trace-fixes-v3.16-rc5-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ring-buffer: Fix polling on trace_pipe
tracing: Add TRACE_ITER_PRINTK flag check in __trace_puts/__trace_bputs
tracing: Fix graph tracer with stack tracer on other archs
tracing: Add ftrace_trace_stack into __trace_puts/__trace_bputs
tracing: instance_rmdir() leaks ftrace_event_file->filter
Need to protect mmio flip programming by event lock as well.
Need to also first enable pflip irq, then mmio program,
otherwise a flip completion may get unnoticed in the vblank
of actual completion if the flip is programmed, but
radeon_flip_work_func gets preempted immediately after
mmio programming and before vblank. In that case the
vblank irq handler wouldn't run radeon_crtc_handle_vblank()
with the completion check routine, miss the completed flip,
and only notice one vblank after actual completion, causing
a false/delayed report of flip completion.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
