This way the connectable changes are synchronized against each other,
which helps avoid potential races. The connectable mode is also linked
together with LE advertising which makes is more convenient to have it
behind the same workqueue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This paves the way for eventually performing advertising changes
through the hdev->req_workqueue. Some new APIs need to be exposed from
mgmt.c to hci_request.c and vice-versa, but many of them will go away
once hdev->req_workqueue gets used.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since Add/Remove Device perform the page scan updates independently
from the HCI command completion we've introduced a potential race when
multiple mgmt commands are queued. Doing the page scan updates through
the req_workqueue ensures that the state changes are performed in a
race-free manner.
At the same time, to make the request helper more widely usable,
extend it to also cover Inquiry Scan changes since those are behind
the same HCI command. This is also reflected in the new name of the
API as well as the work struct name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch increments the management interface revision due to
introduction of a new Get Advertising Size Information command and
various other fixes & improvements.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In order to enable advertising with privacy enabled, SMP has to be
registered in order to generate new RPA. During power on, it will be
registered at the very end which is the reason why advertising is not
enabled and it's not possible to enable it anymore due to mismatch
between hci_dev settings and actual controller state.
This fixes this problem by moving SMP registration earlier, just after
controller is powered (which is ok, because LE SMP will be already able
to decide on identity address to be used), but before advertising is
enabled.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Get Advertising Size Information command allows to retrieve size
information for advertising data and scan response data fields depending
on the selected flags. This is useful if applications want to know the
available size ahead of time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The if statements for checking the flags parameter could be written a
bit easier to read. This changes this. No functional behavior has been
changed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The instance range check for Add Advertising command is missing. If the
provided instance is out of range an Invalid Parameters error should be
returned. At the moment, the generic Failed error is returned. This
extra check ensures that clear error messages are returned.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_connect_le_scan() is (as the name implies) a master/central
role API, so it makes no sense in passing a role parameter to it. At
the same time this patch also fixes the direct advertising support for
LE L2CAP sockets where we now call the more appropriate hci_le_connect()
API if slave/peripheral role is desired.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The recent changes to remove dependency on HCI in Add Device missed
out relevant changes for BR/EDR. This patch removes the left-overs and
ensures the right HCI command gets queued for BR/EDR.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since discovery also deals with LE scanning it makes sense to move it
behind the same req_workqueue as other LE scanning changes. This also
simplifies the logic since we do many of the actions in a synchronous
manner.
Part of this refactoring is moving hci_req_stop_discovery() to
hci_request.c. At the same time the function receives support for
properly handling the STOPPING state since that's the state we'll be
in when stopping through the req_workqueue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since discovery also deals with LE scanning it makes sense to move it
behind the same req_workqueue as other LE scanning changes. This also
simplifies the logic since we do many of the actions in a synchronous
manner.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As preparation for moving the discovery HCI commands behind
req_workqueue, add a helper and do the validity checks of the given
discovery type before proceeding further. This way we don't need to do
them again in hci_request.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To avoid any risks of races, place also these LE scan modification
work callbacks behind the same work queue as the other LE scan
changes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We can easily use the new req_workqueue based background scan update
for the power on case. This also removes the last external user of
__hci_update_background_scan().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no point in waiting for HCI activity in Add/Remove Device
since the effects of these calls are long-lasting and we can anyway
not report up to the application all HCI failures.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of firing off a simple async request queue all background scan
updates through req_workqueue and use hci_req_sync() there to ensure
that no two updates overlap with each other.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Convert the various places mapping connection state to
disconnect/cancel HCI command to use the new hci_abort_conn helper
API.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For connection parameters that are left around until a disconnection
we should at least clear any auto-connection properties. This way a
new Add Device call is required to re-set them after calling Unpair
Device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of doing all of the LE-specific handling in an else-branch in
unpair_device() create a 'done' label for the BR/EDR branch to jump to
and then remove the else-branch completely.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the new hci_conn_hash_lookup_le() API to look up LE connections.
This way we're guaranteed exact matches that also take into account
the address type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The mgmt code needs to convert from mgmt/L2CAP address types to HCI in
many places. Having a dedicated helper function for this simplifies
code by shortening it and removing unnecessary 'addr_type' variables.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The commit 89cbb0638e introduced support for deferred connection
parameter removal when unpairing by removing them only once an
existing connection gets disconnected. However, it failed to address
the scenario when we're *not* connected and do an unpair operation.
What makes things worse is that most user space BlueZ versions will
first issue a disconnect request and only then unpair, meaning the
buggy code will be triggered every time. This effectively causes the
kernel to resume scanning and reconnect to a device for which we've
removed all keys and GATT database information.
This patch fixes the issue by adding the missing call to the
hci_conn_params_del() function to a branch which handles the case of
no existing connection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.19+
There are LE devices on the market that start off by announcing their
public address and then once paired switch to using private address.
To be interoperable with such devices we should simply trust the fact
that we're receiving an IRK from them to indicate that they may use
private addresses in the future. Instead, simply tie the persistency
to the bonding/no-bonding information the same way as for LTKs and
CSRKs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes sure that conn_params that were created just for
explicit_connect, will get properly deleted during cleanup.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Devices undergoing an explicit connect should not have their
conn_params struct removed by the mgmt Remove Device command. This
patch fixes the necessary checks in the command handler to correct the
behavior.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We can't use hci_explicit_connect_lookup() since that would only cover
explicit connections, leaving normal reconnections completely
untouched. Not using it in turn means leaving out entries in
pend_le_reports.
To fix this and simplify the logic move conn params from the reports
list to the pend_le_conns list for the duration of an explicit
connect. Once the connect is complete move the params back to the
pend_le_reports list. This also means that the explicit connect lookup
function only needs to look into the pend_le_conns list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When disable/enable scan command is issued twice, some controllers
will return an error for the second request, i.e. requests with this
command will fail on some controllers, and succeed on others.
This patch makes sure that unnecessary scan disable/enable commands
are not issued.
When adding device to the auto connect whitelist when there is pending
connect attempt, there is no need to update scan.
hci_connect_le_scan_cleanup is conditionally executing
hci_conn_params_del, that is calling hci_update_background_scan. Make
the other case also update scan, and remove reduntand call from
hci_connect_le_scan_remove.
When stopping interleaved discovery the state should be set to stopped
only when both LE scanning and discovery has stopped.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-08-16
Here's what's likely the last bluetooth-next pull request for 4.3:
- 6lowpan/802.15.4 refactoring, cleanups & fixes
- Document 6lowpan netdev usage in Documentation/networking/6lowpan.txt
- Support for UART based QCA Bluetooth controllers
- Power management support for Broeadcom Bluetooth controllers
- Change LE connection initiation to always use passive scanning first
- Support for new Silicon Wave USB ID
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.
This patch enables new connection establishment procedure. Instead of just
sending HCI_OP_LE_CREATE_CONN to controller, "connect" will add device to
kernel whitelist and start scan. If advertisement is received, it'll be
compared against whitelist and then trigger connection if it matches.
That fixes mentioned reconnect issue for already paired devices. It also
make whole connection procedure more robust. We can try to connect to
multiple devices at same time now, even though controller allow only one.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.
This path makes sure that after advertisement is received from device that
we try to connect to, it is properly handled in check_pending_le_conn and
trigger connect attempt.
It also modifies hci_le_connect to make sure that connect attempt will be
properly continued.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds hci_lookup_le_connect method, that will be used to check
wether outgoing le connection attempt is in progress.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes how MGMT_EV_NEW_LONG_TERM_KEY event is build. Right now
val vield is filled with only 1 byte, instead of whole value. This bug
was introduced in
commit 1fc62c526a ("Bluetooth: Fix exposing full value of shortened LTKs")
Before that patch, if you paired with device using bluetoothd using simple
pairing, and then restarted bluetoothd, you would be able to re-connect,
but device would fail to establish encryption and would terminate
connection. After this patch connecting after bluetoothd restart works
fine.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move IRK checking logic in preparation to new connect method. Also
make sure that MGMT_STATUS_INVALID_PARAMS is returned when non
identity address is passed to ADD_DEVICE. Right now MGMT_STATUS_FAILED
is returned, which might be misleading.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Rework the logic of checking for a valid adv_instance for non-zero
cp->instance values. Without this change we may get (false positive)
warnings as follows:
>> net/bluetooth/mgmt.c:7294:29: warning: 'adv_instance' may be used
uninitialized in this function [-Wuninitialized]
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch increments the management interface revision due to
introduction of new multi-advertising feature and various bug fixes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
During service discovery, advertising will be disabled. This patch
ensures that it is correctly being re-enabled, both for configuration
made via set advertising and add advertising, once the scanning
times out.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch ensures that instance advertising is correctly canceled
before starting a le scan.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Advertising instances programmed while powered off should be advertised
once the device is powered. This patch ensures that all combinations
of setting and/or adding advertising configuration while powered off
will be correctly activated on power on.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The remove_advertising() and remove_advertising_complete() functions
had instance identifiers hard coded. Notably, when passing in 0x00 as
an instance identifier to signal that all instances should be removed
then the mgmt API would return a hard coded 0x01 rather than returning
the expected value 0x00. This bug is being fixed by always referencing
the instance identifier from the management API call instead.
remove_advertising() is refactored to use the new dynamic advertising
instance list. The logic is being changed to make multi-instance
advertising actually work, notably the schedule_adv_instance() method is
being referenced to make sure that other instances will continue to
advertise even if one instance is being removed.
The code is made more readable by factoring advertising instance
management and initialization into the low-level
hci_remove_adv_instance() and hci_adv_instances_clear() functions.
The method now references the clear_adv_instance() helper method to
remove duplicate logic and code.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The add_advertising() and add_advertising_complete() functions reference
the now obsolete hdev->adv_instance struct. Both methods are being
refactored to access the dynamic advertising instance list instead.
This patch also introduces all logic necessary to actually deal with
multiple instance advertising. Notably the mgmt_adv_inst_expired() and
schedule_adv_inst() method are being referenced to schedule instances in
a round robin fashion.
This patch also introduces a "pending" flag into the adv_info struct.
This is necessary to identify and remove recently added advertising
instances when the HCI commands return with an error status code.
Otherwise new advertising instances could be leaked without properly
informing userspace about their existence.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The clear_adv_instance() function could not clean up multiple
advertising instances previously. It is being changed to provide both, a
means to clean up a single instance and cleaning up all instances at
once.
An additional instance parameter is being introduced to achieve this.
Passing in 0x00 to this parameter signifies that all instances should be
cleaned up. This semantics has been chosen similarly to the semantics of
the instance parameter in the remove_advertising() function.
When removing a single instance the method also ensures that another
instance will be scheduled if available. When the currently advertising
method is being removed, it will be canceled immediately.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The set_advertising() and set_advertising_complete() methods rely on
the now obsolete hci_dev->adv_instance structure. We replace this
reference by an equivalent access to the newly introduced dynamic
advertising instance list.
This patch introduces a helper function that schedules an advertising
instance correctly calculating advertising timing based on the timeout
and duration settings of the instance. Scheduling is factored into
its own function for readability and code sharing.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The create_instance_adv_data() function could not deal with
multiple advertising instances previously. This is being fixed by
retrieving advertising instances from the newly introduced dynamic
advertising instance list.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The create_instance_scan_rsp_data() function could not deal with
multiple advertising instances previously. This is being fixed by adding
an additional instance parameter.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Previously enable_advertising() would rely on
get_adv_instance_scan_rsp_len() which checked for a hard coded instance
identifier. This is being changed to check for the current advertising
instance's scan response length instead. The function is renamed
accordingly.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Switch if and else conditions to replace a negative statement by a
positive one which makes the condition more readable.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The get_adv_instance_flags() would not work with instance identifiers
other than 0x01. This is being fixed so that arbitrary instance
identifiers can be dealt with while still correctly dealing with the
special case of the 0x00 identifier.
Signed-off-by: Florian Grandel <fgrandel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
