If SHARED_KERNEL_PMD is false, then we need to allocate and initialize
the kernel pmd. We can easily piggy-back this onto the existing pmd
prepopulation code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In PAE mode, an update to the pgd requires a cr3 reload to make sure
the processor notices the changes. Since this also has the
side-effect of flushing the tlb, its an expensive operation which we
want to avoid where possible.
This patch mitigates the cost of installing the initial set of pmds on
process creation by preallocating them when the pgd is allocated.
This avoids up to three tlb flushes during exec, as it creates the new
process address space while the pagetable is in active use.
The pmds will be freed as part of the normal pagetable teardown in
free_pgtables, which is called in munmap and process exit. However,
free_pgtables will only free parts of the pagetable which actually
contain mappings, so stray pmds may still be attached to the pgd at
pgd_free time. We must mop them up to prevent a memory leak.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: William Irwin <wli@holomorphy.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Deal properly with pmd-level pages being allocated and freed
dynamically. We can handle them more or less the same as pte pages.
Also, deal with early_ioremap pagetable manipulations.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Convert macros into inline functions, for better type-checking.
This patch required a little bit of fiddling with headers in order to
make __(pte|pmd)_free_tlb inline rather than macros.
asm-generic/tlb.h includes asm/pgalloc.h, though it doesn't directly
use any pgalloc definitions. I removed this include to avoid an
include cycle, but it may cause secondary compile failures by things
depending on the indirect inclusion; arch/x86/mm/hugetlbpage.c was one
such place; there may be others.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add mm to paravirt_alloc_pd, partly to make it consistent with
paravirt_alloc_pt, and because later changes will make use of it.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Looks like a mismerge/misapply dropped one of the cases of pte flag
masking for Xen. Also, only mask the flags for present ptes.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
old sequence:
size ==> >4G ==> point to RAM
changed to:
>4G ==> point to RAM ==> size
some bios even leave aper to unclear, so check size at last.
To avoid reporting:
Node 0: Aperture @ 4a42000000 size 32 MB
Aperture too small (32 MB)
with this change we will get:
Node 0: Aperture @ 4a42000000 size 32 MB
Aperture beyond 4G. Ignoring.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some consumer ICH9 boards (such as the Abit IP35 Pro) do not provide a BIOS
option for enabling the HPET. The same ICH workaround used for 6,7,8 can be
applied to 9. Here I enable the only PCI id that was visible on my system.
I have confirmed the HPETs work both from userspace and as a clocksource for
the running kernel (2.6.24 here) after applying this patch.
Force enabled HPET at base address 0xfed00000
hpet clockevent registered
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
hpet0: 4 64-bit timers, 14318180 Hz
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
in init/main.c boot_cpu_init() does that before.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
in init/main.c boot_cpu_init() already does that before setup_arch
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remainder of unification can occur inplace.
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There seems to be a preference for the 64 bit version so use that on 32 bit and
drop the stray leading "."
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The files are now identical so merge them.
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
vmlinux_64 and vmlinux_32.scr are now identical
size shows an expected movement from .text to .rodata and 4 extra bytes
of padding.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Without this patch the linker will generate a section
named .sched.text.1 which is unexpected.
This is because the gcc generated section has "ax" but the
assembler usage of .sched.text lacks the "ax" specifier.
It would be better to have a definition we could use from
assembler code but I did not find a suitable header
file for it.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix the following warning:
WARNING: arch/x86/kernel/built-in.o(.cpuinit.text+0x7a3): Section mismatch: reference to .init.text:amd_detect_cmp in 'init_amd'
The function amd_detect_cmp were annotated __init and
was only used from init_amd() which are annotated __cpuinit.
Annotate amd_detect_cmp() with _cpuinit to fix it.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix following warning:
WARNING: arch/x86/kernel/built-in.o(__ksymtab+0x2b0): Section mismatch: reference to .cpuinit.text:arch_register_cpu in '__ksymtab_arch_register_cpu'
Annotating exported symbols are wrong.
Previously the warning were hidden by avoiding the export
in the non HOTPLUG_CPU case but the improved checks in
modpost caught it anyway.
Fix it by removing the __cpuinit annotation and rearrange the
code a bit to save one ifdef/endif pair.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix the following warnings:
WARNING: arch/x86/mm/built-in.o(.text+0x1abc): Section mismatch: reference to .init.data:nodes_parsed in 'unparse_node'
WARNING: arch/x86/mm/built-in.o(.text+0x1ac6): Section mismatch: reference to .cpuinit.data:apicid_to_node in 'unparse_node'
WARNING: arch/x86/mm/built-in.o(.text+0x1ad2): Section mismatch: reference to .cpuinit.data:apicid_to_node in 'unparse_node'
unparse_node are static and only used by acpi_scan_nodes which
is already annotated __init.
So we annotate unparse_node with __init.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix following warnings:
WARNING: arch/x86/kernel/built-in.o(.text+0x139e1): Section mismatch: reference to .init.data:early_qrk in 'check_dev_quirk'
WARNING: arch/x86/kernel/built-in.o(.text+0x139f5): Section mismatch: reference to .init.data:early_qrk in 'check_dev_quirk'
WARNING: arch/x86/kernel/built-in.o(.text+0x13a0c): Section mismatch: reference to .init.data:early_qrk in 'check_dev_quirk'
WARNING: arch/x86/kernel/built-in.o(.text+0x13a12): Section mismatch: reference to .init.data:early_qrk in 'check_dev_quirk'
WARNING: arch/x86/kernel/built-in.o(.text+0x13a1a): Section mismatch: reference to .init.data:early_qrk in 'check_dev_quirk'
WARNING: arch/x86/kernel/built-in.o(.text+0x13a36): Section mismatch: reference to .init.data:early_qrk in 'check_dev_quirk'
WARNING: arch/x86/kernel/built-in.o(.text+0x13a42): Section mismatch: reference to .init.data:
Warning was caused by access to the __initdata annotated variable
from the non-annotated static function check_dev_quirk().
check_dev_quirk() were only used from a function annotated
__init so add __init annotation to check_dev_quirk() to fix it.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix following warning:
WARNING: arch/x86/kernel/built-in.o(.text+0x10ea0): Section mismatch: reference to .cpuinit.data:num_processors in 'acpi_unmap_lsapic'
The exported function acpi_unmap_lsapic() references
the variable num_processors that is annotated __cpuinitdata.
Remove the annotation of num_processors as we never know
when an exported function are called.
And drop the needless initialsation to 0.
Warning was seen on 64 bit but similar pattern were seen
in 32 bit - so fix it up there too.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix the following warning:
WARNING: arch/x86/kernel/built-in.o(.text+0x3): Section mismatch: reference to .cpuinit.data:force_mwait in 'mwait_usable'
[Seen on 64 bit only but similar pattern exist on 32 bit so fix it there too]
mwait_usable() were only used by a function annotated __cpuinit
so annotate mwait_usable() with __cpuinit to fix the warning.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix following warning:
WARNING: arch/x86/kernel/cpu/mcheck/built-in.o(.text+0x1584): Section mismatch: reference to .cpuinit.text:threshold_create_device in 'threshold_cpu_callback'
threshold_cpu_callback() is only used by threshold_cpu_notifier.
threshold_cpu_notifier is only used for cpu hot plug as it is registered
using register_hotcpu_notifier().
Mark them both __cpuinit to fix the warning.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix following warning:
WARNING: arch/x86/kernel/cpu/mcheck/built-in.o(.text+0x752): Section mismatch: reference to .cpuinit.text:mce_create_device in 'mce_cpu_callback'
mce_cpu_callback() is only used by mce_cpu_notofier.
The notifier is only used for hotplugable cpu's as it is
registered using register_hotcpu_notifier(),
Annotate them both __cpuinit to fix the warning.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The RDC R-321x SoC needs a reboot fixup which
uses its internal hardware watchdog set to
reset the CPU on next tick.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds support for the RDC R-321x system-on-chip,
also known as R-861x-(G). It uses the generic GPIO API and
has support for the on-chip hardware watchdog.
Build-fix from: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch defines the PCI identifiers found in
the RDC R-321x System-on-Chip.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds the generic GPIO support to the x86
architecture. We do the same as for MIPS, we let
the machine override the gpio callbacks and provide
defaults one in mach-generic.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The existing Geode GPIO API only allows for updating one GPIO at once. There
are instances where users want to update multiple GPIOs at once. With the
current API, they are given two choices; either ignore the GPIO API:
outl(0xc000, gpio_base + GPIO_OUTPUT_VAL);
outl(0xc000, gpio_base + GPIO_OUTPUT_ENABLE);
Alternatively, call each GPIO update separately:
geode_gpio_set(14, GPIO_OUTPUT_VAL);
geode_gpio_set(15, GPIO_OUTPUT_VAL);
geode_gpio_set(14, GPIO_OUTPUT_ENABLE);
geode_gpio_set(15, GPIO_OUTPUT_ENABLE);
Neither are desirable. This patch changes the GPIO API to allow for setting
of multiple GPIOs at once; rather than being passed an integer, we pass
a bitmask and provide a translation function. The above code would now
look like this:
geode_gpio_set(geode_gpio(14)|geode_gpio(15), GPIO_OUTPUT_VAL);
geode_gpio_set(geode_gpio(14)|geode_gpio(15), GPIO_OUTPUT_ENABLE);
Since there are no upstream users of the GPIO API yet (afaik), best to
change this now. This also adds a bit of sanity checking; it is no
longer possible to use a GPIO above 28.
Note the semantics of geode_gpio_isset() have changed:
geode_gpio_isset(geode_gpio(3)|geode_gpio(4), ...)
will only return true iff both GPIOs are set.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix cpu MHz reporting for AMD family 0x11 when powernow-k8 is
disabled.
Just adhere to the CONSTANT_TSC feature bit for AMD CPUs when deciding
whether cpu_khz needs calibration. The additional check for CPU family
is not needed and prevents calibration for future CPUs.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
improve the MTTR trimming messages and also trigger a WARN_ON()
so that kerneloops.org can pick it up and categorize it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I found a small bug of NUMA emulation code for x86_64. (CONFIG_NUMA_EMU)
If machine is non-NUMA, find_node_by_addr() should return
NUMA_NO_NODE, but current implementation code returns existent maximum
NUMA node number + 1.
This is not existent NUMA node number.
However, this behaviour does not affect NUMA emulation fortunately, because
acpi_fake_nodes() that is caller of find_node_by_addr() gets pxm
(proximity domain) by node_to_pxm() from non-existent NUMA node number
that was returned by find_node_by_addr().
node_to_pxm() returns PXM_INVAL that means illegal or non-existent
NUMA node number.
Signed-off-by: Minoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Both of these references to cpu_to_node() can potentially occur
before the "late" cpu_to_node map is setup. Therefore, they
should be changed to use early_cpu_to_node().
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The new "mfgptfix" boot command line option may be usd to fix MFGPT
timers on AMD Geode platforms when the BIOS has incorrectly applied
a workaround. TinyBIOS version 0.98 is known to be affected, 0.99
fixes the problem by letting the user disable the workaround.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
No one uses struct cpu_model_info on x86_64 now.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use KSYM_NAME_LEN instead of numeric value
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
when MTRRs are not covering the whole e820 table, we need to trim the
RAM and need to update e820.
reuse some code on 64-bit as well.
here need to add early_get_cap and use it in early_cpu_detect, and move
mtrr_bp_init early.
The code successfully trimmed the memory map on Justin's system:
from:
[ 0.000000] BIOS-e820: 0000000100000000 - 000000022c000000 (usable)
to:
[ 0.000000] modified: 0000000100000000 - 0000000228000000 (usable)
[ 0.000000] modified: 0000000228000000 - 000000022c000000 (reserved)
According to Justin it makes quite a difference:
| When I boot the box without any trimming it acts like a 286 or 386,
| takes about 10 minutes to boot (using raptor disks).
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
fix kconfig text and make DEBUG_RODATA default.
this helps debugging quite a bit.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
With this, the paravirt_ops code can be enabled on x86_64 also.
Each guest implementation (Xen, VMI, lguest) now depends on X86_32. The
dependencies can be dropped for each one when they start to support
x86_64.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
