Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- Rework the irqdomain core infrastructure to accomodate ACPI based
systems. This is required to support ARM64 without creating
artificial device tree nodes.
- Sanitize the ACPI based ARM GIC initialization by making use of the
new firmware independent irqdomain core
- Further improvements to the generic MSI management
- Generalize the irq migration on CPU hotplug
- Improvements to the threaded interrupt infrastructure
- Allow the migration of "chained" low level interrupt handlers
- Allow optional force masking of interrupts in disable_irq[_nosysnc]
- Support for two new interrupt chips - Sigh!
- A larger set of errata fixes for ARM gicv3
- The usual pile of fixes, updates, improvements and cleanups all
over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
Document that IRQ_NONE should be returned when IRQ not actually handled
PCI/MSI: Allow the MSI domain to be device-specific
PCI: Add per-device MSI domain hook
of/irq: Use the msi-map property to provide device-specific MSI domain
of/irq: Split of_msi_map_rid to reuse msi-map lookup
irqchip/gic-v3-its: Parse new version of msi-parent property
PCI/MSI: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Add support code for multi-parent version of "msi-parent"
irqchip/gic-v3-its: Add handling of PCI requester id.
PCI/MSI: Add helper function pci_msi_domain_get_msi_rid().
of/irq: Add new function of_msi_map_rid()
Docs: dt: Add PCI MSI map bindings
irqchip/gic-v2m: Add support for multiple MSI frames
irqchip/gic-v3: Fix translation of LPIs after conversion to irq_fwspec
irqchip/mxs: Add Alphascale ASM9260 support
irqchip/mxs: Prepare driver for hardware with different offsets
irqchip/mxs: Panic if ioremap or domain creation fails
irqdomain: Documentation updates
irqdomain/msi: Use fwnode instead of of_node
...
Pull ARM updates from Russell King:
"In this ARM merge, we remove more lines than we add. Changes include:
- Enable imprecise aborts early, so that bus errors aren't masked
until later in the boot. This has the side effect that boot
loaders which provoke these aborts can cause the kernel to crash
early in boot, so we install a handler to report this event around
the site where these are enabled.
- Remove the buggy but impossible to enable cmpxchg syscall code.
- Add unwinding annotations to some assembly code.
- Add support for atomic half-word exchange for ARMv6k+.
- Reduce ioremap() alignment for SMP/LPAE cases where we don't need
the large alignment.
- Addition of an "optimal" 3G configuration for systems with 1G of
RAM.
- Increase vmalloc space by 128M.
- Constify some SMP operations structures, which have never been
writable.
- Improve ARMs dma_mmap() support for mapping DMA coherent mappings
into userspace.
- Fix to the NMI backtrace code in the IPI case on ARM where the
failing CPU gets stuck for 10s waiting for its own IPI to be
delivered.
- Removal of legacy PM support from the AMBA bus driver.
- Another fix for the previous fix of vdsomunge"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (23 commits)
ARM: 8449/1: fix bug in vdsomunge swab32 macro
arm: add missing of_node_put
ARM: 8447/1: catch pending imprecise abort on unmask
ARM: 8446/1: amba: Remove unused callbacks for legacy system PM
ARM: 8443/1: Adding support for atomic half word exchange
ARM: clean up TWD after previous patch
ARM: 8441/2: twd: Don't set CLOCK_EVT_FEAT_C3STOP unconditionally
ARM: 8440/1: remove obsolete documentation
ARM: make highpte an expert option
ARM: 8433/1: add a VMSPLIT_3G_OPT config option
ARM: 8439/1: Fix backtrace generation when IPI is masked
ARM: 8428/1: kgdb: Fix registers on sleeping tasks
ARM: 8427/1: dma-mapping: add support for offset parameter in dma_mmap()
ARM: 8426/1: dma-mapping: add missing range check in dma_mmap()
ARM: remove user cmpxchg syscall
ARM: 8438/1: Add unwinding to __clear_user_std()
ARM: 8436/1: hw_breakpoint: remove unnecessary header
ARM: 8434/2: Revert "7655/1: smp_twd: make twd_local_timer_of_register() no-op for nosmp"
ARM: 8432/1: move VMALLOC_END from 0xff000000 to 0xff800000
ARM: 8430/1: use default ioremap alignment for SMP or LPAE
...
- Add 'invert' sysfs attribute to the heartbeat trigger.
- Add Device Tree support to the leds-netxbig driver and add
related DT nodes to the kirkwood-netxbig.dtsi and kirkwood-net5big.dts
files. Remove static LED setup from the related board files.
- Remove redundant brightness conversion operation from leds-netxbig.
- Improve leds-bcm6328 driver: improve default-state handling, add more
init configuration options, print invalid LED instead of warning only
about maximum LED value.
- Add a shutdown function for setting gpio-leds into off state
when shutting down.
- Fix DT flash timeout property naming in leds-aat1290.txt.
- Switch to using devm prefixed version of led_classdev_register()
(leds-cobalt-qube, leds-hp6xx, leds-ot200, leds-ipaq-micro,
leds-netxbig, leds-locomo, leds-menf21bmc, leds-net48xx,
leds-wrap).
- Add missing of_node_put (leds-powernv, leds-bcm6358, leds-bcm6328,
leds-88pm860x).
- Coding style fixes and cleanups: led-class/led-core, leds-ipaq-micro.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=X8+e
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
- Move the out-of-LED-tree led-sead3 driver to the LED subsystem.
- Add 'invert' sysfs attribute to the heartbeat trigger.
- Add Device Tree support to the leds-netxbig driver and add related DT
nodes to the kirkwood-netxbig.dtsi and kirkwood-net5big.dts files.
Remove static LED setup from the related board files.
- Remove redundant brightness conversion operation from leds-netxbig.
- Improve leds-bcm6328 driver: improve default-state handling, add more
init configuration options, print invalid LED instead of warning only
about maximum LED value.
- Add a shutdown function for setting gpio-leds into off state when
shutting down.
- Fix DT flash timeout property naming in leds-aat1290.txt.
- Switch to using devm prefixed version of led_classdev_register()
(leds-cobalt-qube, leds-hp6xx, leds-ot200, leds-ipaq-micro,
leds-netxbig, leds-locomo, leds-menf21bmc, leds-net48xx, leds-wrap).
- Add missing of_node_put (leds-powernv, leds-bcm6358, leds-bcm6328,
leds-88pm860x).
- Coding style fixes and cleanups: led-class/led-core, leds-ipaq-micro.
* tag 'leds_for_4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (27 commits)
leds: 88pm860x: add missing of_node_put
leds: bcm6328: add missing of_node_put
leds: bcm6358: add missing of_node_put
powerpc/powernv: add missing of_node_put
leds: leds-wrap.c: Use devm_led_classdev_register
leds: aat1290: Fix property naming of flash-timeout-us
leds: leds-net48xx: Use devm_led_classdev_register
leds: leds-menf21bmc.c: Use devm_led_class_register
leds: leds-locomo.c: Use devm_led_classdev_register
leds: leds-gpio: add shutdown function
Documentation: leds: update DT bindings for leds-bcm6328
leds-bcm6328: add more init configuration options
leds-bcm6328: simplify and improve default-state handling
leds-bcm6328: print invalid LED
leds: netxbig: set led_classdev max_brightness
leds: netxbig: convert to use the devm_ functions
ARM: mvebu: remove static LED setup for netxbig boards
ARM: Kirkwood: add LED DT entries for netxbig boards
leds: netxbig: add device tree binding
leds: triggers: add invert to heartbeat
...
flash-timeout-us property name is changed to flash-max-timeout-us.
This patch fixes that name.
Signed-off-by: Ingi Kim <ingi2.kim@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch adds device tree support for the netxbig LEDs.
This also introduces a additionnal DT binding for the GPIO extension bus
(netxbig-gpio-ext) used to configure the LEDs. Since this bus could also
be used to control other devices, then it seems more suitable to have it
in a separate DT binding.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
GPIO core:
- Define and handle flags for open drain/open collector
and open source/open emitter, also know as "single-ended"
configurations.
- Generic request/free operations that handle calling out
to the (optional) pin control backend.
- Some refactoring related to an ABI change that did not
happen, yet provide useful.
- Added a real-time compliance checklist. Many GPIO chips
have irqchips, and need to think this over with the RT
patches going upstream.
- Restructure, fix and clean up Kconfig menus a bit.
New drivers:
- New driver for AMD Promony.
- New driver for ACCES 104-IDIO-16, a port-mapped I/O
card, ISA-style. Very retro.
Subdriver changes:
- OMAP changes to handle real time requirements.
- Handle trigger types for edge and level IRQs on PL061
properly. As this hardware is very common it needs to
set a proper example for others to follow.
- Some container_of() cleanups.
- Delete the unused MSM driver in favor of the driver that
is embedded inside the pin control driver.
- Cleanup of the ath79 GPIO driver used by many, many
OpenWRT router targets.
- A consolidated IT87xx driver replacing the earlier
very specific IT8761e driver.
- Handle the TI TCA9539 in the PCA953x driver. Also
handle ACPI devices in this subdriver.
- Drop xilinx arch dependencies as these FPGAs seem to
profilate over a few different architectures. MIPS and
ARM come to mind.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWNz3qAAoJEEEQszewGV1zKlAP/R+mVoQHyfDFurChDzuWQjZK
T4eDiFGTHr/MUDP9I0jINF400SfEm3ajm3aoPvKc6fA2d7oLNB7TzyUxjDsQV4h8
NsCJ9IYD9xYgF6SDovPYPZ6SkRJYimDrwjD/DUSR8ijisVzJwYCyEGznelWKnQMo
Fcw4kOTMrW0034ZT4nGH4kSgIzNAMcecazaaqLisniYZ/4Ozk1CQsrBK1gCO/kr8
Hh3N/mN4TBvOyIuD7lmN5PnWuJo641rplcWErjxUZYvqEddSfAnpasfAcXMkZ4gM
jOK+l7VIycxOAn+EJwqjyVPJ0gDPPaMwB836gogzNraO2SYd/R2JvyI2zyTogmdW
MNwsKwP2b/ma/h0A/JBDFmcMiJwA2QHHgylLrB+vfWAP9o2nJv++Op1/q8ktVR+1
EgEk9StVvnYqC86DJhYbUbMmX7TorRwPoUo/5Z6C/viyZzOagZge0vYKYTQS99Pq
B+2aH7pMPLooAdU/cyYy8J20mxQ4RaHoy+TCe0RMRhxnRi9CnnnYNHbZDVdHISpr
OSfZKSM40DbAAs7UNxIgPXM1qSzia23tgzZEdh5qwQtZBTC6fWr/1xOrTpFW2wY6
VxqgP/OX23BzJQE4YDnOHLIj8GX0MLqXr7pl2+KBcHO9xvPS6Qj8fFsLEVatCwX0
Caify6KIbbgMWcVmut/6
=LDCr
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for the v4.4 development cycle.
The only changes hitting outside drivers/gpio are in the pin control
subsystem and these seem to have settled nicely in linux-next.
Development mistakes and catfights are nicely documented in the
reverts as you can see. The outcome of the ABI fight is that we're
working on a chardev ABI for GPIO now, where hope to show results for
the v4.5 kernel.
Summary of changes:
GPIO core:
- Define and handle flags for open drain/open collector and open
source/open emitter, also know as "single-ended" configurations.
- Generic request/free operations that handle calling out to the
(optional) pin control backend.
- Some refactoring related to an ABI change that did not happen, yet
provide useful.
- Added a real-time compliance checklist. Many GPIO chips have
irqchips, and need to think this over with the RT patches going
upstream.
- Restructure, fix and clean up Kconfig menus a bit.
New drivers:
- New driver for AMD Promony.
- New driver for ACCES 104-IDIO-16, a port-mapped I/O card,
ISA-style. Very retro.
Subdriver changes:
- OMAP changes to handle real time requirements.
- Handle trigger types for edge and level IRQs on PL061 properly. As
this hardware is very common it needs to set a proper example for
others to follow.
- Some container_of() cleanups.
- Delete the unused MSM driver in favor of the driver that is
embedded inside the pin control driver.
- Cleanup of the ath79 GPIO driver used by many, many OpenWRT router
targets.
- A consolidated IT87xx driver replacing the earlier very specific
IT8761e driver.
- Handle the TI TCA9539 in the PCA953x driver. Also handle ACPI
devices in this subdriver.
- Drop xilinx arch dependencies as these FPGAs seem to profilate over
a few different architectures. MIPS and ARM come to mind"
* tag 'gpio-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (57 commits)
gpio: fix up SPI submenu
gpio: drop surplus I2C dependencies
gpio: drop surplus X86 dependencies
gpio: dt-bindings: document the official use of "ngpios"
gpio: MAINTAINERS: Add an entry for the ATH79 GPIO driver
gpio / ACPI: Allow shared GPIO event to be read via operation region
gpio: group port-mapped I/O drivers in a menu
gpio: Add ACCES 104-IDIO-16 driver maintainer entry
gpio: zynq: Document interrupt-controller DT binding
gpio: xilinx: Drop architecture dependencies
gpio: generic: Revert to old error handling in bgpio_map
gpio: add a real time compliance notes
Revert "gpio: add a real time compliance checklist"
gpio: Add GPIO support for the ACCES 104-IDIO-16
gpio: driver for AMD Promontory
gpio: xlp: Convert to use gpiolib irqchip helpers
gpio: add a real time compliance checklist
gpio/xilinx: enable for MIPS
gpiolib: Add and use OF_GPIO_SINGLE_ENDED flag
gpiolib: Split GPIO flags parsing and GPIO configuration
...
v4.4 kernel development cycle:
Infrastructure:
- Doug Anderson wrote a patch adding an "init" state
different from the "default" state for pin control
state handling in the core framework. This is applied
before the driver's probe() call if defined and takes
precedence over "default". If both are defined, "init"
will be applied *before* probe() and "default" will be
applied *after* probe().
Significant subdriver improvements:
- SH PFC is switched to getting GPIO ranges from the
device tree ranges property on DT platforms.
- Got rid of CONFIG_ARCH_SHMOBILE_LEGACY, we are all
modernized.
- Got rid of SH PFC hardcoded IRQ numbers.
- Allwinner sunxi external interrupt through the "r"
controller.
- Moved the Cygnus driver to use DT-provided GPIO
ranges.
New drivers:
- Atmel PIO4 pin controller for the SAMA4D2 family
New subdrivers:
- Rockchip RK3036 subdriver
- Renesas SH PFC R8A7795 subdriver
- Allwinner sunxi A83T PIO subdriver
- Freescale i.MX7d iomux lpsr subdriver
- Marvell Berlin BG4CT subdriver
- SiRF Atlas 7 step B SoC subdriver
- Intel Broxton SoC subdriver
Apart from this, the usual slew if syntactic and semantic
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0t3B
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.4 kernel
development cycle. Development pace is high in pin control again this
merge window. 28 contributors, 83 patches.
It hits a few sites outside the pin control subsystem:
- Device tree bindings in Documentation (as usual)
- MAINTAINERS
- drivers/base/* for the "init" state handling by Doug Anderson.
This has been ACKed by Greg.
- drivers/usb/renesas_usbhs/rcar2.c, for a dependent Renesas change
in the USB subsystem. This has been ACKed by both Greg and Felipe.
- arch/arm/boot/dts/sama5d2.dtsi - this should ideally have gone
through the ARM SoC tree but ended up here.
This time I am using Geert Uytterhoeven as submaintainer for SH PFC
since the are three-four people working in parallel with new Renesas
ASICs.
Summary of changes:
Infrastructure:
- Doug Anderson wrote a patch adding an "init" state different from
the "default" state for pin control state handling in the core
framework. This is applied before the driver's probe() call if
defined and takes precedence over "default". If both are defined,
"init" will be applied *before* probe() and "default" will be
applied *after* probe().
Significant subdriver improvements:
- SH PFC is switched to getting GPIO ranges from the device tree
ranges property on DT platforms.
- Got rid of CONFIG_ARCH_SHMOBILE_LEGACY, we are all modernized.
- Got rid of SH PFC hardcoded IRQ numbers.
- Allwinner sunxi external interrupt through the "r" controller.
- Moved the Cygnus driver to use DT-provided GPIO ranges.
New drivers:
- Atmel PIO4 pin controller for the SAMA4D2 family
New subdrivers:
- Rockchip RK3036 subdriver
- Renesas SH PFC R8A7795 subdriver
- Allwinner sunxi A83T PIO subdriver
- Freescale i.MX7d iomux lpsr subdriver
- Marvell Berlin BG4CT subdriver
- SiRF Atlas 7 step B SoC subdriver
- Intel Broxton SoC subdriver
Apart from this, the usual slew if syntactic and semantic fixes"
* tag 'pinctrl-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (81 commits)
pinctrl: pinconf: remove needless loop
pinctrl: uniphier: guard uniphier directory with CONFIG_PINCTRL_UNIPHIER
pinctrl: zynq: fix UTF-8 errors
pinctrl: zynq: Initialize early
pinctrl: at91: add missing of_node_put
pinctrl: tegra-xusb: Correct lane mux options
pinctrl: intel: Add Intel Broxton pin controller support
pinctrl: intel: Allow requesting pins which are in ACPI mode as GPIOs
pinctrl: intel: Add support for multiple GPIO chips sharing the interrupt
drivers/pinctrl: Add the concept of an "init" state
pinctrl: uniphier: set input-enable before pin-muxing
pinctrl: cygnus: Add new compatible string for gpio controller driver
pinctrl: cygnus: Remove GPIO to Pinctrl pin mapping from driver
pinctrl: cygnus: Optional DT property to support pin mappings
pinctrl: sunxi: Add irq pinmuxing to sun6i "r" pincontroller
pinctrl: sunxi: Fix irq_of_xlate for the r_pio pinctrl block
pinctrl: sh-pfc: Remove obsolete r8a7778 platform_device_id entry
pinctrl: sh-pfc: Remove obsolete r8a7779 platform_device_id entry
pinctrl: sh-pfc: Stop including <linux/platform_data/gpio-rcar.h>
usb: renesas_usbhs: Remove unneeded #include <linux/platform_data/gpio-rcar.h>
...
* L3 and SoC support for xgene_edac. (Loc Ho)
* AMD F15h, models 0x60-6f support to amd64_edac. (Aravind Gopalakrishnan)
* Fixes and cleanups all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ek5l
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"A bunch of fixes all over the place and some hw enablement this time.
- Convert EDAC to debugfs wrappers and make drivers use those
(Borislav Petkov)
- L3 and SoC support for xgene_edac (Loc Ho)
- AMD F15h, models 0x60-6f support to amd64_edac (Aravind
Gopalakrishnan)
- Fixes and cleanups all over the place"
* tag 'edac_for_4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (22 commits)
EDAC: Fix PAGES_TO_MiB macro misuse
EDAC, altera: SoCFPGA EDAC should not look for ECC_CORR_EN
EDAC: Use edac_debugfs_remove_recursive()
EDAC, ppc4xx_edac: Fix module autoload for OF platform driver
Documentation/EDAC: Add reference documents section for amd64_edac
EDAC, amd64_edac: Update copyright and remove changelog
EDAC, amd64_edac: Extend scrub rate support to F15hM60h
EDAC: Don't allow empty DIMM labels
EDAC: Fix sysfs dimm_label store operation
EDAC: Fix sysfs dimm_label show operation
arm64, EDAC: Add L3/SoC DT subnodes to the APM X-Gene SoC EDAC node
EDAC, xgene: Add SoC support
EDAC, xgene: Fix possible sprintf() overflow issue
EDAC, xgene: Add L3 support
EDAC, Documentation: Update X-Gene EDAC binding for L3/SoC subnodes
EDAC, sb_edac: Fix TAD presence check for sbridge_mci_bind_devs()
EDAC, ghes_edac: Remove redundant memory_type array
EDAC, xgene: Convert to debugfs wrappers
EDAC, i5100: Convert to debugfs wrappers
EDAC, altera: Convert to debugfs wrappers
...
- Add new API to set VCCQ voltage - mmc_regulator_set_vqmmc()
- Add new ioctl to allow userspace to send multi commands
- Wait for card busy signalling before starting SDIO requests
- Remove MMC_CLKGATE
- Enable tuning for DDR50 mode
- Some code clean-up/improvements to mmc pwrseq
- Use highest priority for eMMC restart handler
- Add DT bindings for eMMC hardware reset support
- Extend the mmc_send_tuning() API
- Improve ios show for debugfs
- A couple of code optimizations
MMC host:
- Some generic OF improvements
- Various code clean-ups
- sirf: Add support for DDR50
- sunxi: Add support for card busy detection
- mediatek: Use MMC_CAP_RUNTIME_RESUME
- mediatek: Add support for eMMC HW-reset
- mediatek: Add support for HS400
- dw_mmc: Convert to use the new mmc_regulator_set_vqmmc() API
- dw_mmc: Add external DMA interface support
- dw_mmc: Some various improvements
- dw_mmc-rockchip: MMC tuning with the clock phase framework
- sdhci: Properly clear IRQs during resume
- sdhci: Enable tuning for DDR50 mode
- sdhci-of-esdhc: Use IRQ mode for card detection
- sdhci-of-esdhc: Support both BE and LE host controller
- sdhci-pci: Build o2micro support in the same module
- sdhci-pci: Support for new Intel host controllers
- sdhci-acpi: Support for new Intel host controllers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gn/m
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.4' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add new API to set VCCQ voltage - mmc_regulator_set_vqmmc()
- Add new ioctl to allow userspace to send multi commands
- Wait for card busy signalling before starting SDIO requests
- Remove MMC_CLKGATE
- Enable tuning for DDR50 mode
- Some code clean-up/improvements to mmc pwrseq
- Use highest priority for eMMC restart handler
- Add DT bindings for eMMC hardware reset support
- Extend the mmc_send_tuning() API
- Improve ios show for debugfs
- A couple of code optimizations
MMC host:
- Some generic OF improvements
- Various code clean-ups
- sirf: Add support for DDR50
- sunxi: Add support for card busy detection
- mediatek: Use MMC_CAP_RUNTIME_RESUME
- mediatek: Add support for eMMC HW-reset
- mediatek: Add support for HS400
- dw_mmc: Convert to use the new mmc_regulator_set_vqmmc() API
- dw_mmc: Add external DMA interface support
- dw_mmc: Some various improvements
- dw_mmc-rockchip: MMC tuning with the clock phase framework
- sdhci: Properly clear IRQs during resume
- sdhci: Enable tuning for DDR50 mode
- sdhci-of-esdhc: Use IRQ mode for card detection
- sdhci-of-esdhc: Support both BE and LE host controller
- sdhci-pci: Build o2micro support in the same module
- sdhci-pci: Support for new Intel host controllers
- sdhci-acpi: Support for new Intel host controllers"
* tag 'mmc-v4.4' of git://git.linaro.org/people/ulf.hansson/mmc: (73 commits)
mmc: dw_mmc: fix the wrong setting for UHS-DDR50 mode
mmc: dw_mmc: fix the CardThreshold boundary at CardThrCtl register
mmc: dw_mmc: NULL dereference in error message
mmc: pwrseq: Use highest priority for eMMC restart handler
mmc: mediatek: add HS400 support
mmc: mmc: extend the mmc_send_tuning()
mmc: mediatek: add implement of ops->hw_reset()
mmc: mediatek: fix got GPD checksum error interrupt when data transfer
mmc: mediatek: change the argument "ddr" to "timing"
mmc: mediatek: make cmd_ints_mask to const
mmc: dt-bindings: update Mediatek MMC bindings
mmc: core: Add DT bindings for eMMC hardware reset support
mmc: omap_hsmmc: Enable omap_hsmmc for Keystone 2
mmc: sdhci-acpi: Add more ACPI HIDs for Intel controllers
mmc: sdhci-pci: Add more PCI IDs for Intel controllers
arm: lpc18xx_defconfig: remove CONFIG_MMC_DW_IDMAC
arm: hisi_defconfig: remove CONFIG_MMC_DW_IDMAC
arm: exynos_defconfig: remove CONFIG_MMC_DW_IDMAC
arc: axs10x_defconfig: remove CONFIG_MMC_DW_IDMAC
mips: pistachio_defconfig: remove CONFIG_MMC_DW_IDMAC
...
There are a bunch of drivers that utilize the "ngpios" DT property
without any vendor prefix. Try to start cleaning up the mess by
defining what we mean by this property.
Cc: devicetree@vger.kernel.org
Cc: Pramod Kumar <pramodku@broadcom.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
HW and driver support the GPIO as interrupt-controller.
Document that in the DT binding.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This new compatible string, "brcm,iproc-gpio", should be used for
all new iproc-based future SoCs.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If GPIO controller's pins are muxed, pin-controller subsystem
need to be intimated by defining mapping between gpio and
pinmux controller. This patch adds required properties to
define this mapping via DT.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sometime only need set MMC_CAP_HW_RESET for one of MMC hosts,
So set it in device tree is better.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
synopsys-dw-mshc supports three types of transfer mode. We add
bindings and description for how to use them at runtime.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas R8A7794 SoC also has the MMCIF controller.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "compatible" property text contradicts even the example given in the MMCIF
binding document itself; moreover, the Renesas MMCIF driver only matches on
the generic "compatible" string and doesn't look for the SoC specific strings
at all. Thus describe "renesas,sh-mmcif" as a fallback value.
Fixes: b4c27763d7 ("mmc: sh_mmcif: Document DT bindings")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add ciu_drive, ciu_sample clocks and default-sample-phase. This will later
be used by tuning code.
We do not touch ciu_drive (and by extension define default-drive-phase).
Drive phase is mostly used to define minimum hold times, while one could
write some code to determine what phase meets the minimum hold time
(ex 10 degrees) this will not work with the current clock phase framework
(which floors angles, so we'll get 0 deg, and there's no way to know what
resolution the floors happen at). We assume that the default drive angles
set by the hardware are good enough.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
add the ability to parse "phy-handle". This
is needed for phys, which have a DT node, and
need to parse DT properties.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add berlin4ct to existing berlin pinctrl device tree binding.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently msi-parent is used by a few bindings to describe the
relationship between a PCI root complex and a single MSI controller, but
this property does not have a generic binding document.
Additionally, msi-parent is insufficient to describe more complex
relationships between MSI controllers and devices under a root complex,
where devices may be able to target multiple MSI controllers, or where
MSI controllers use (non-probeable) sideband information to distinguish
devices.
This patch adds a generic binding for mapping PCI devices to MSI
controllers. This document covers msi-parent, and a new msi-map property
(specific to PCI*) which may be used to map devices (identified by their
Requester ID) to sideband data for each MSI controller that they may
target.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Here are some small USB and PHY fixes and quirk updates for 4.3-rc5.
Nothing major here, full details in the shortlog, and all of these have
been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlYZOFUACgkQMUfUDdst+ymLSACeLNl7IWSxq2acJ5rhUl5+LRxp
KtsAn3lMXJryk4xw2WpfJg30TXpWXnNM
=n9ei
-----END PGP SIGNATURE-----
Merge tag 'usb-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB and PHY fixes and quirk updates for 4.3-rc5.
Nothing major here, full details in the shortlog, and all of these
have been in linux-next for a while"
* tag 'usb-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: Add device quirk for Logitech PTZ cameras
USB: chaoskey read offset bug
USB: Add reset-resume quirk for two Plantronics usb headphones.
usb: renesas_usbhs: Add support for R-Car H3
usb: renesas_usbhs: fix build warning if 64-bit architecture
usb: gadget: bdc: fix memory leak
phy: berlin-sata: Fix module autoload for OF platform driver
phy: rockchip-usb: power down phy when rockchip phy probe
phy: qcom-ufs: fix build error when the component is built as a module
In 5388a6b266 ("ARM: SMP: Always enable clock event broadcast support")
Russell noted that "the TWD local timers are unable to wake up the CPU
when it is placed into a low power mode".
However, some platforms do not stop the TWD block in low-power mode,
and can thus use the TWD timer in one-shot mode, without setting up
a broadcast device.
Make the driver check for the "always-on" boolean property, and set
the CLOCK_EVT_FEAT_C3STOP flag accordingly.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The TCA9539 is almost identical to the PCA9555 and software-compatible
with this driver. It exposes 16 general purpose I/O pins in two 8-bit
configurations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull input layer fixes from Dmitry Torokhov:
"Fixes for two recent regressions (in Synaptics PS/2 and uinput
drivers) and some more driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - fix handling of disabling gesture mode"
Input: psmouse - fix data race in __ps2_command
Input: elan_i2c - add all valid ic type for i2c/smbus
Input: zhenhua - ensure we have BITREVERSE
Input: omap4-keypad - fix memory leak
Input: serio - fix blocking of parport
Input: uinput - fix crash when using ABS events
Input: elan_i2c - expand maximum product_id form 0xFF to 0xFFFF
Input: elan_i2c - add ic type 0x03
Input: elan_i2c - don't require known iap version
Input: imx6ul_tsc - fix controller name
Input: imx6ul_tsc - use the preferred method for kzalloc()
Input: imx6ul_tsc - check for negative return value
Input: imx6ul_tsc - propagate the errors
Input: walkera0701 - fix abs() calculations on 64 bit values
Input: mms114 - remove unneded semicolons
Input: pm8941-pwrkey - remove unneded semicolon
Input: fix typo in MT documentation
Input: cyapa - fix address of Gen3 devices in device tree documentation
Add iomuxc-lpsr devicetree bindings documentation
Provide documentation context as well an example on
pheriperals that could use pad from either iomuxc controller
supported by iMX7D SoC
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is customary for GPIO controllers to support open drain/collector
and open source/emitter configurations. Add standard GPIO line flags
to account for this and augment the documentation to say that these
are the most generic bindings.
Several people approached me to add new flags to the lines, and this
makes sense, but let's first bind up the most common cases before we
start to add exotic stuff.
Thanks to H. Nikolaus Schaller for ideas on how to encode single-ended
wiring such as open drain/source and open collector/emitter.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove this driver now that Bjorn has introduced a pinctrl driver
for msm8660 and the dts files have been updated with the pinctrl
compatibles.
Cc: Andy Gross <agross@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allwinner A83T soc port controller has 8 ports.
It has 3 IRQ banks namely PB, PG, PH.
Pinmuxing are different for some pins as compared to
sun8i A23 and A33.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds a compatible string to support for R-Car H3.
Since the HS-USB controller of R-Car H3 is almost the same specification
with R-Car Gen2 (these have 16 pipes and usb-dmac), this patch
sets the "type" of renesas_usbhs_driver_param to USBHS_TYPE_RCAR_GEN2.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For some reason the name of the external interrupt controller
has changed name with r8a7795, so use "intc-ex" instead of "irqc"
as r8a7795 compat string to follow the friendly documentation.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: horms@verge.net.au
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: jason@lakedaemon.net
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20150928094228.32552.83336.sendpatchset@little-apple
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit fe78d0b769 ("spi: sh-msiof: Fix FIFO size to 64 word from
256 word") changed the default RX FIFO size on R-Car Gen2 SoCs in the
driver code, but forgot to update the DT bindings documentation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull MIPS fixes from Ralf Baechle:
- Properly setup irq handling for ATH79 platforms
- Fix bootmem mapstart calculation for contiguous maps
- Handle little endian and older CPUs correct in BPF
- Fix console for Fulong 2E systems
- Handle FTLB correctly on R6 CPUs
- Fixes for CM, GIC and MAAR support code
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Initialise MAARs on secondary CPUs
MIPS: print MAAR configuration during boot
MIPS: mm: compile maar_init unconditionally
irqchip: mips-gic: Fix pending & mask reads for MIPS64 with 32b GIC.
irqchip: mips-gic: Convert CPU numbers to VP IDs.
MIPS: CM: Provide a function to map from CPU to VP ID.
MIPS: Fix FTLB detection for R6
MIPS: cpu-features: Add cpu_has_ftlb
MIPS: ATH79: Add irq chip ar7240-misc-intc
MIPS: ATH79: Set missing irq ack handler for ar7100-misc-intc irq chip
MIPS: BPF: Fix build on pre-R2 little endian CPUs
MIPS: BPF: Avoid unreachable code on little endian
MIPS: bootmem: Fix mapstart calculation for contiguous maps
MIPS: Fix console output for Fulong2e system
Here are some USB driver fixes for 4.3-rc3.
There's the usual assortment of new device ids, combined with xhci and
gadget driver fixes. Full details in the shortlog. All of these have
been in linux-next with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlYGzJ0ACgkQMUfUDdst+yneGACgxrj/ZJGgY09tkItvvejHoYrF
tgQAoI/cRL7C9aoWt7DjMxmbFnQE8hC7
=jsj/
-----END PGP SIGNATURE-----
Merge tag 'usb-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB driver fixes for 4.3-rc3.
There's the usual assortment of new device ids, combined with xhci and
gadget driver fixes. Full details in the shortlog. All of these have
been in linux-next with no reported problems"
* tag 'usb-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (34 commits)
MAINTAINERS: remove amd5536udc USB gadget driver maintainer
USB: whiteheat: fix potential null-deref at probe
xhci: init command timeout timer earlier to avoid deleting it uninitialized
xhci: change xhci 1.0 only restrictions to support xhci 1.1
usb: xhci: exit early in xhci_setup_device() if we're halted or dying
usb: xhci: stop everything on the first call to xhci_stop
usb: xhci: Clear XHCI_STATE_DYING on start
usb: xhci: lock mutex on xhci_stop
xhci: Move xhci_pme_quirk() behind #ifdef CONFIG_PM
xhci: give command abortion one more chance before killing xhci
usb: Use the USB_SS_MULT() macro to get the burst multiplier.
usb: dwc3: gadget: Fix BUG in RT config
usb: musb: fix cppi channel teardown for isoch transfer
usb: phy: isp1301: Export I2C module alias information
usb: gadget: drop null test before destroy functions
usb: gadget: dummy_hcd: in transfer(), return data sent, not limit
usb: gadget: dummy_hcd: fix rescan logic for transfer
usb: gadget: dummy_hcd: fix unneeded else-if condition
usb: gadget: dummy_hcd: emulate sending zlp in packet logic
usb: musb: dsps: fix polling in device-only mode
...
Resource management
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn Helgaas)
MSI
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f4c3
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for things we merged for v4.3 (VPD, MSI, and bridge
window management), and a new Renesas R8A7794 SoC device ID.
Details:
Resource management:
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn
Helgaas)
MSI:
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver:
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous:
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)"
* tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rcar: Add R8A7794 support
PCI: Use function 0 VPD for identical functions, regular VPD for others
PCI: Fix devfn for VPD access through function 0
PCI/MSI: Fix MSI IRQ domains for VFs on virtual buses
PCI: Clear IORESOURCE_UNSET when clipping a bridge window
PCI: Revert "PCI: Call pci_read_bridge_bases() from core instead of arch code"
- Silence bogus warning for of_irq_parse_pci
- Fix typo in ARM idle-states binding doc and dts files
- Various minor binding documentation updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWBI2/AAoJEMhvYp4jgsXi08cH/11S/92w1PLNmWCv4y7TXHQw
XTJi7/Hk+q6otV/FigXukdYClR17h/3mFyCKKXHrkAgy/AoSrvN/ABe0bLLoT2AQ
xh0Rx8F6vZwa6ro1MZcrn3ZxQkoJlNUhoIXtY84oSPWd1ernLOar6HonFiynCQQc
bDZo5zoLj6DBbSO+UpVvEQN57ogwPgFZ1hGDjJeyyH8c1755z2OVA+k8O0dwjmqW
Xav/7TO8bFEIbUnfWeKnVyK45qmJxHcTbn3nxUgYFQj3DMI2Hn86WEY4cg8QvTo+
SpdO1Aio6b9NSTNnpiSvPnc2MFNPFaWjiqm1w86w+PTm8oUT+p1V0OG/EE27fcY=
=VUfk
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- Silence bogus warning for of_irq_parse_pci
- Fix typo in ARM idle-states binding doc and dts files
- Various minor binding documentation updates
* tag 'devicetree-fixes-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
Documentation: arm: Fix typo in the idle-states bindings examples
gpio: mention in DT binding doc that <name>-gpio is deprecated
of_pci_irq: Silence bogus "of_irq_parse_pci() failed ..." messages.
devicetree: bindings: Extend the bma180 bindings with bma250 info
of: thermal: Mark cooling-*-level properties optional
of: thermal: Fix inconsitency between cooling-*-state and cooling-*-level
Docs: dt: add #msi-cells to GICv3 ITS binding
of: add vendor prefix for Socionext Inc.
The idle-states bindings mandate that the entry-method string
in the idle-states node must be "psci" for ARM v8 64-bit systems,
but the examples in the bindings report a wrong entry-method string.
Owing to this typo, some dts in the kernel wrongly defined the
entry-method property, since they likely cut and pasted the example
definition without paying attention to the bindings definitions.
This patch fixes the typo in the DT idle states bindings examples and
respective dts in the kernel so that the bindings and related dts
files are made compliant.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Howard Chen <howard.chen@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rob Herring <robh@kernel.org>
The gpiolib supports parsing DT properties of the form <name>-gpio but it
was only added for compatibility with older DT bindings that got it wrong
and should not be used in newer bindings.
The commit that added support for this was:
dd34c37aa3 ("gpio: of: Allow -gpio suffix for property names")
but didn't update the documentation to explain this so it's been a source
of confusion. So let's make this clear in the GPIO DT binding doc.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add Renesas R8A7794 SoC support to the Renesas R-Car gen2 PCI driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
