The _PAGE_IO_MAP PTE flag was only used by Xen PV guests to mark PTEs
that were used to map I/O regions that are 1:1 in the p2m. This
allowed Xen to obtain the correct PFN when converting the MFNs read
from a PTE back to their PFN.
Xen guests no longer use _PAGE_IOMAP for this. Instead mfn_to_pfn()
returns the correct PFN by using a combination of the m2p and p2m to
determine if an MFN corresponds to a 1:1 mapping in the the p2m.
Remove _PAGE_IOMAP, replacing it with _PAGE_UNUSED2 to allow for
future uses of the PTE flag.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Commit 30919b0bf3 ("x86: avoid low BIOS area when allocating address
space") moved the test for resource allocations that fall within the first
1MB of address space from the PCI-specific path to a generic path, such
that all resource allocations will avoid this area. However, this breaks
ISA cards which need to allocate a memory region within the first 1MB. An
example is the i82365 PCMCIA controller and derivatives like the Ricoh
RF5C296/396 which map part of the PCMCIA socket memory address space into
the first 1MB of system memory address space. They do not work anymore as
no usable memory region exists due to this change:
Intel ISA PCIC probe: Ricoh RF5C296/396 ISA-to-PCMCIA at port 0x3e0 ofs 0x00, 2 sockets
host opts [0]: none
host opts [1]: none
ISA irqs (scanned) = 3,4,5,9,10 status change on irq 10
pcmcia_socket pcmcia_socket1: pccard: PCMCIA card inserted into slot 1
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3ff: excluding 0x170-0x177 0x1f0-0x1f7 0x2f8-0x2ff 0x370-0x37f 0x3c0-0x3e7 0x3f0-0x3ff
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0a0000-0x0affff: excluding 0xa0000-0xaffff
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0b0000-0x0bffff: excluding 0xb0000-0xbffff
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0cffff: excluding 0xc0000-0xcbfff
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0d0000-0x0dffff: clean.
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0e0000-0x0effff: clean.
pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: clean.
pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3ff: excluding 0x170-0x177 0x1f0-0x1f7 0x2f8-0x2ff 0x370-0x37f 0x3c0-0x3e7 0x3f0-0x3ff
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0a0000-0x0affff: excluding 0xa0000-0xaffff
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0b0000-0x0bffff: excluding 0xb0000-0xbffff
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0c0000-0x0cffff: excluding 0xc0000-0xcbfff
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0d0000-0x0dffff: clean.
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0e0000-0x0effff: clean.
pcmcia_socket pcmcia_socket1: cs: memory probe 0x60000000-0x60ffffff: clean.
pcmcia_socket pcmcia_socket1: cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia_socket pcmcia_socket1: cs: memory probe 0x0cc000-0x0effff: excluding 0xe0000-0xeffff
pcmcia_socket pcmcia_socket1: cs: unable to map card memory!
If filtering out the first 1MB is reverted, everything works as expected.
Tested-by: Robert Resch <fli4l@robert.reschpara.de>
Signed-off-by: Christoph Schulz <develop@kristov.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v2.6.37+
Move the pcibios_assign_resources() fs_initcall annotation next to the
function definition. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Don't attempt to move resource marked IORESOURCE_PCI_FIXED, even if
pci_claim_resource() fails. In some cases, these are legacy resources that
cannot be moved.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In hotplug case (especially with Thunderbolt enabled systems) we might need
to call pcibios_resource_survey_bus() several times for a bus. The function
ends up calling pci_claim_resource() for each bridge resource that then
fails claiming that the resource exists already (which it does). Once this
happens the resource is invalidated thus preventing devices behind the
bridge to allocate their resources.
To fix this we do what has been done in pcibios_allocate_dev_resources()
and check 'parent' of the given resource. If it is non-NULL it means that
the resource has been allocated already and we can skip it. We do the same
for ROM resources as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
During testing remove/rescan root bus 00, found
[ 338.142574] bus: 'pci': really_probe: probing driver ata_piix with device 0000:00:01.1
[ 338.146788] ata_piix 0000:00:01.1: device not available (can't reserve [io 0x01f0-0x01f7])
[ 338.150565] ata_piix: probe of 0000:00:01.1 failed with error -22
because that fixed resource is not claimed.
For bootint path it is claimed in from
arch/x86/pci/i386.c::pcibios_allocate_resources()
Claim those resources, so on the remove/rescan will still use old
resources.
It is some kind honoring FW setting in the registers during hot add.
esp root-bus hot add is through acpi, BIOS has chance to set some registers
before handing over.
[bhelgaas: move weak definition to patch that uses it]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI resource allocation functions will be used for hot-added
devices, so keep them around.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The BIOS doesn't assign BAR values for hot-added devices, so don't
bother saving the original values when we enumerate these devices.
[bhelgaas: changelog, return constant 0 in pcibios_retrieve_fw_addr]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Factor pcibios_allocate_rom_resources() and
pcibios_allocate_dev_rom_resource() out of pcibios_assign_resources().
This will allow us to allocate ROM resources for hot-added root buses.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously pcibios_allocate_resources() allocated resources at boot-time
for all PCI devices using for_each_pci_dev(). This patch changes
pcibios_allocate_resources() so we can specify a bus, so we can do
similar allocation when hot-adding a root bus.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Factor pcibios_allocate_dev_resources() out of
pcibios_allocate_resources(). Currently we only allocate these
resources at boot-time with a for_each_pci_dev() loop. Eventually
we'll use pcibios_allocate_dev_resources() for hot-added devices, too.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Thus pcibios_allocate_bus_resources() could more simple and clean.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
spin_is_locked() is always false on UP kernels: spin_lock_irqsave() does no
locking, so we can't tell whether the lock is held or not. Therefore,
this warning is only valid for SMP kernels.
CC: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
'pcibios_fwaddrmap_lookup()' is used to maintain FW-assigned BIOS BAR
values for reinstatement when normal resource assignment attempts
fail and must be called with the 'pcibios_fwaddrmap_lock' spinlock
held.
This patch adds a WARN_ON notification if the spinlock is not currently
held by the caller.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch converts the underlying maintenance aspects of FW-assigned
BIOS BAR values from a statically allocated array within struct pci_dev
to a list of temporary, stand alone, entries.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 58c84eda07 introduced functionality to try and reinstate the
original BIOS BAR addresses of a PCI device when normal resource
assignment attempts fail. To keep track of the BIOS BAR addresses,
struct pci_dev was augmented with an array to hold the BAR addresses
of the PCI device: 'resource_size_t fw_addr[DEVICE_COUNT_RESOURCE]'.
The reinstatement of BAR addresses is an uncommon event leaving the
'fw_addr' array unused under normal circumstances. This functionality
is also currently architecture specific with an implementation limited
to x86. As the use of struct pci_dev is so prevalent, having the
'fw_addr' array residing within such seems somewhat wasteful.
This patch introduces a stand alone data structure and interfacing
routines for maintaining a list of FW-assigned BIOS BAR value entries.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The 'latency timer' of PCI devices, both Type 0 and Type 1,
is setup in architecture-specific code [see: 'pcibios_set_master()'].
There are two approaches being taken by all the architectures - check
if the 'latency timer' is currently set between 16 and 255 and if not
bring it within bounds, or, do nothing (and then there is the
gratuitously different PA-RISC implementation).
There is nothing architecture-specific about PCI's 'latency timer' so
this patch pulls its setup functionality up into the PCI core by
creating a generic 'pcibios_set_master()' function using the '__weak'
attribute which can be used by all architectures as a default which,
if necessary, can then be over-ridden by architecture-specific code.
No functional change.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These files were implicitly getting EXPORT_SYMBOL via device.h
which was including module.h, but that will be fixed up shortly.
By fixing these now, we can avoid seeing things like:
arch/x86/kernel/rtc.c:29: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
arch/x86/kernel/pci-dma.c:20: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
arch/x86/kernel/e820.c:69: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’
[ with input from Randy Dunlap <rdunlap@xenotime.net> and also
from Stephen Rothwell <sfr@canb.auug.org.au> ]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
They were generated by 'codespell' and then manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: trivial@kernel.org
LKML-Reference: <1300389856-1099-3-git-send-email-lucas.demarchi@profusion.mobi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This implements arch_remove_reservations() so allocate_resource() can
avoid any arch-specific reserved areas. This currently just avoids the
BIOS area (the first 1MB), but could be used for E820 reserved areas if
that turns out to be necessary.
We previously avoided this area in pcibios_align_resource(). This patch
moves the test from that PCI-specific path to a generic path, so *all*
resource allocations will avoid this area.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
and branch 'for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm
* 'for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
xen: register xen pci notifier
xen: initialize cpu masks for pv guests in xen_smp_init
xen: add a missing #include to arch/x86/pci/xen.c
xen: mask the MTRR feature from the cpuid
xen: make hvc_xen console work for dom0.
xen: add the direct mapping area for ISA bus access
xen: Initialize xenbus for dom0.
xen: use vcpu_ops to setup cpu masks
xen: map a dummy page for local apic and ioapic in xen_set_fixmap
xen: remap MSIs into pirqs when running as initial domain
xen: remap GSIs as pirqs when running as initial domain
xen: introduce XEN_DOM0 as a silent option
xen: map MSIs into pirqs
xen: support GSI -> pirq remapping in PV on HVM guests
xen: add xen hvm acpi_register_gsi variant
acpi: use indirect call to register gsi in different modes
xen: implement xen_hvm_register_pirq
xen: get the maximum number of pirqs from xen
xen: support pirq != irq
* 'stable/xen-pcifront-0.8.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (27 commits)
X86/PCI: Remove the dependency on isapnp_disable.
xen: Update Makefile with CONFIG_BLOCK dependency for biomerge.c
MAINTAINERS: Add myself to the Xen Hypervisor Interface and remove Chris Wright.
x86: xen: Sanitse irq handling (part two)
swiotlb-xen: On x86-32 builts, select SWIOTLB instead of depending on it.
MAINTAINERS: Add myself for Xen PCI and Xen SWIOTLB maintainer.
xen/pci: Request ACS when Xen-SWIOTLB is activated.
xen-pcifront: Xen PCI frontend driver.
xenbus: prevent warnings on unhandled enumeration values
xenbus: Xen paravirtualised PCI hotplug support.
xen/x86/PCI: Add support for the Xen PCI subsystem
x86: Introduce x86_msi_ops
msi: Introduce default_[teardown|setup]_msi_irqs with fallback.
x86/PCI: Export pci_walk_bus function.
x86/PCI: make sure _PAGE_IOMAP it set on pci mappings
x86/PCI: Clean up pci_cache_line_size
xen: fix shared irq device passthrough
xen: Provide a variant of xen_poll_irq with timeout.
xen: Find an unbound irq number in reverse order (high to low).
xen: statically initialize cpu_evtchn_mask_p
...
Fix up trivial conflicts in drivers/pci/Makefile
Allocate from the end of a region, not the beginning.
For example, if we need to allocate 0x800 bytes for a device on bus
0000:00 given these resources:
[mem 0xbff00000-0xdfffffff] PCI Bus 0000:00
[mem 0xc0000000-0xdfffffff] PCI Bus 0000:02
the available space at [mem 0xbff00000-0xbfffffff] is passed to the
alignment callback (pcibios_align_resource()). Prior to this patch, we
would put the new 0x800 byte resource at the beginning of that available
space, i.e., at [mem 0xbff00000-0xbff007ff].
With this patch, we put it at the end, at [mem 0xbffff800-0xbfffffff].
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=16228#c41
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When mapping pci space via /sys or /proc, make sure we're really
doing a hardware mapping by setting _PAGE_IOMAP.
[ Impact: bugfix; make PCI mappings map the right pages ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: "H. Peter Anvin" <hpa@zytor.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: x86@kernel.org
If we fail to assign resources to a PCI BAR, this patch makes us try the
original address from BIOS rather than leaving it disabled.
Linux tries to make sure all PCI device BARs are inside the upstream
PCI host bridge or P2P bridge apertures, reassigning BARs if necessary.
Windows does similar reassignment.
Before this patch, if we could not move a BAR into an aperture, we left
the resource unassigned, i.e., at address zero. Windows leaves such BARs
at the original BIOS addresses, and this patch makes Linux do the same.
This is a bit ugly because we disable the resource long before we try to
reassign it, so we have to keep track of the BIOS BAR address somewhere.
For lack of a better place, I put it in the struct pci_dev.
I think it would be cleaner to attempt the assignment immediately when the
claim fails, so we could easily remember the original address. But we
currently claim motherboard resources in the middle, after attempting to
claim PCI resources and before assigning new PCI resources, and changing
that is a fairly big job.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16263
Reported-by: Andrew <nitr0@seti.kr.ua>
Tested-by: Andrew <nitr0@seti.kr.ua>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Yannick found that video does not work with 2.6.34. The cause of this
bug was that the BIOS had assigned the wrong range to the PCI bridge
above the video device. Before 2.6.34 the kernel would have shrunk
the size of the bridge window, but since
d65245c PCI: don't shrink bridge resources
the kernel will avoid shrinking BIOS ranges.
So zero out the old range if we fail to claim it at boot time; this will
cause us to allocate a new range at startup, restoring the 2.6.34
behavior.
Fixes regression https://bugzilla.kernel.org/show_bug.cgi?id=16009.
Reported-by: Yannick <yannick.roehlly@free.fr>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When we move a PCI device or assign resources to a device not configured
by the BIOS, we want to avoid the BIOS region below 1MB. Note that if the
BIOS places devices below 1MB, we leave them there.
See https://bugzilla.kernel.org/show_bug.cgi?id=15744
and https://bugzilla.kernel.org/show_bug.cgi?id=15841
Tested-by: Andy Isaacson <adi@hexapodia.org>
Tested-by: Andy Bailey <bailey@akamai.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_claim_resource() already prints more detailed error messages, so these
are really redundant.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'x86-bootmem-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
early_res: Need to save the allocation name in drop_range_partial()
sparsemem: Fix compilation on PowerPC
early_res: Add free_early_partial()
x86: Fix non-bootmem compilation on PowerPC
core: Move early_res from arch/x86 to kernel/
x86: Add find_fw_memmap_area
Move round_up/down to kernel.h
x86: Make 32bit support NO_BOOTMEM
early_res: Enhance check_and_double_early_res
x86: Move back find_e820_area to e820.c
x86: Add find_early_area_size
x86: Separate early_res related code from e820.c
x86: Move bios page reserve early to head32/64.c
sparsemem: Put mem map for one node together.
sparsemem: Put usemap for one node together
x86: Make 64 bit use early_res instead of bootmem before slab
x86: Only call dma32_reserve_bootmem 64bit !CONFIG_NUMA
x86: Make early_node_mem get mem > 4 GB if possible
x86: Dynamically increase early_res array size
x86: Introduce max_early_res and early_res_count
...
Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Should be good for 32bit too.
-v3: cast res->start
-v4: according to Linus, to use %pR instead of cast
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-9-git-send-email-yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This allows us to use the BIOS SR-IOV allocations rather than assigning
our own later on.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This makes PCI resource management messages more consistent and adds a few
new messages to aid debugging.
Whenever we assign resources to a device, update a BAR, or change a
bridge aperture, it's worth noting it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Jesse accidentally applied v1 [1] of the patchset instead of v2 [2]. This
is the diff between v1 and v2.
The changes in this patch are:
- tidied vsprintf stack buffer to shrink and compute size more
accurately
- use %pR for decoding and %pr for "raw" (with type and flags) instead
of adding %pRt and %pRf
[1] http://lkml.org/lkml/2009/10/6/491
[2] http://lkml.org/lkml/2009/10/13/441
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Thomas Schlichter reported:
> X.org uses libpciaccess which tries to mmap with write combining enabled via
> /sys/bus/pci/devices/*/resource0_wc. Currently, when PAT is not enabled, the
> kernel does fall back to uncached mmap. Then libpciaccess thinks it succeeded
> mapping with write combining enabled and does not set up suited MTRR entries.
> ;-(
Instead of silently mapping pci mmap region as UC minus in the case
of !pat_enabled and wc request, we can return error. Eric Anholt mentioned
that caller (like X) typically follows up with UC minus pci mmap request and
if there is a free mtrr slot, caller will manage adding WC mtrr.
Jesse Barnes says:
> Older versions of libpciaccess will behave better if we do it that way
> (iirc it only allocates an MTRR if the resource_wc file doesn't exist or
> fails to get mapped).
Reported-by: Thomas Schlichter <thomas.schlichter@web.de>
Signed-off-by: Thomas Schlichter <thomas.schlichter@web.de>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen reported that his DL585 G2 needed noapic after 2.6.22 (?)
Dann bisected it down to:
commit 30a18d6c3f
Date: Tue Feb 19 03:21:20 2008 -0800
x86: multi pci root bus with different io resource range, on
64-bit
It turns out that:
1. that AMD-based systems have two HT chains.
2. BIOS doesn't allocate resources for BAR 6 of devices under 8132 etc
3. that multi-peer-root patch will try to split root resources to peer
root resources according to PCI conf of NB
4. PCI core assigns unassigned resources, but they overlap with BARs
that are used by ioapic addr of io4 and 8132.
The reason: at that point ioapic address are not inserted yet. Solution
is to insert ioapic resources into the tree a bit earlier.
Reported-by: Stephen Frost <sfrost@snowman.net>
Reported-and-Tested-by: dann frazier <dannf@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@jbarnes-g45.(none)>
Instead of open-coding pci_find_parent_resource and request_resource,
just call pci_claim_resource.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename set_pci_bus_resources_arch_default to x86_pci_root_bus_res_quirks, move
the weak version from common.c to i386.c, and before calling, make sure it's a
root bus.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci mmap code was doing memtype reserve for a while now. Recently we
added memtype tracking in remap_pfn_range, and pci code indirectly calls
remap_pfn_range. So, we don't need seperate tracking in pci code
anymore. Which means a patch that removes ~50 lines of code :-).
Also, recently we found out that the pci tracking is not working as we expect
it to work in some cases. Specifically, userlevel X mmap of pci, with some
recent version of X, is having a problem with vm_page_prot getting reset.
The pci tracking uses vm_page_prot to pass on the protection type from parent
to child during fork.
a) Parent does a pci mmap
b) We look at PAT and get either UC_MINUS or WC mapping for parent
c) Store that mapping type in vma vm_page_prot for future use
d) This thread does a fork
e) Fork results in mmap_ops ->open for the child process
f) We get the vm_page_prot from vma and reserve that type for the child process
But, between c) and e) above, the vma vm_page_prot is getting reset to zero.
This results in PAT reserve failing at the time of fork as in here.
http://marc.info/?l=linux-kernel&m=123858163103240&w=2
This cleanup makes the above problem go away as we do not depend on
vm_page_prot in our PAT code anymore.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While looking at the issue in the thread:
http://marc.info/?l=dri-devel&m=123606627824556&w=2
noticed a bug in pci PAT code and memory type setting.
PCI mmap code did not set the proper protection in vma, when it
inherited protection in reserve_memtype. This bug only affects
the case where there exists a WC mapping before X does an mmap
with /proc or /sys pci interface. This will cause X userlevel
mmap from /proc or /sysfs to fail on fork.
Reported-by: Kevin Winchester <kjwinchester@gmail.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: <stable@kernel.org>
LKML-Reference: <20090323190720.GA16831@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Move the new memtype old memtype allowed check to header so that is can be
shared by other users. Subsequent patch uses this in pat.c in remap_pfn_range()
code path. No functionality change in this patch.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
These are easy to trigger (more or less harmlessly) with multiple video
cards, since the ROM BAR will typically not be given any space by the
BIOS bridge setup. No reason to punish quiet boot for this.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Impact: cleanup
Now that arch/x86/pci/pci.h is used in a number of other places as well,
move the lowlevel x86 pci definitions into the architecture include files.
(not to be confused with the existing arch/x86/include/asm/pci.h file,
which provides public details about x86 PCI)
Tested on: X86_32_UP, X86_32_SMP and X86_64_SMP
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
this one replaces:
| commit a2bd7274b4
| Author: Yinghai Lu <yhlu.kernel@gmail.com>
| Date: Mon Aug 25 00:56:08 2008 -0700
|
| x86: fix HPET regression in 2.6.26 versus 2.6.25, check hpet against BAR, v3
v2: insert e820 reserve resources before pnp_system_init
v3: fix merging problem in tip/x86/core
v4: address Linus's review about comments and condition in _late()
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so could let BAR res register at first, or even pnp.
v2: insert e820 reserve resources before pnp_system_init
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Breaking lines due to some imaginary problem with a long line length is
often stupid and wrong, but never more so when it splits a string that
is printed out into multiple lines. This really ended up making it much
harder to find where some error strings were printed out, because a
simple 'grep' didn't work.
I'm sure there is tons more of this particular idiocy hiding in other
places, but this particular case hit me once more last week. So fix it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
