The Broadcom 7211 has new functionality that allows some USB low
speed side band signals, that go from the XHCI host controller to
pins on the chip, to be remapped to use any GPIO pin instead of the
limited set selectable by hardware. This can be done without changing
the standard driver for the host controller. There is currently
support for three USB signals, PWRON, VBUS_PRESENT and PWRFLT. This
driver will allow the remapping of any of these three signals based
on settings in the Device Tree node for the driver. The driver was
written so that it could handle additional signals added in the
future by just adding the correct properties to the DT node.
Below is an example of a DT node that would remap all three
signals:
usb_pinmap: usb-pinmap@22000d0 {
compatible = "brcm,usb-pinmap";
reg = <0x22000d0 0x4>;
in-gpios = <&gpio 18 0>, <&gpio 19 0>;
brcm,in-functions = "VBUS", "PWRFLT";
brcm,in-masks = <0x8000 0x40000 0x10000 0x80000>;
out-gpios = <&gpio 20 0>;
brcm,out-functions = "PWRON";
brcm,out-masks = <0x20000 0x800000 0x400000 0x200000>;
interrupts = <0x0 0xb2 0x4>;
};
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20201012200007.8862-3-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719160910.60018-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
iOS devices will not draw more than 500mA unless instructed to do so.
Setting the charge type power supply property to "fast" tells the device
to start drawing more power, using the same procedure that official
"MFi" chargers would.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191016093933.693-7-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191121132901.29186-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190923154956.6868-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Rio500 kernel driver has not been used by Rio500 owners since 2001
not long after the rio500 project added support for a user-space USB stack
through the very first versions of usbdevfs and then libusb.
Support for the kernel driver was removed from the upstream utilities
in 2008:
943f624ab7
Cc: Cesar Miquel <miquel@df.uba.ar>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/6251c17584d220472ce882a3d9c199c401a51a71.camel@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big USB and PHY driver pull request for 5.3-rc1.
Lots of stuff here, all of which has been in linux-next for a while with
no reported issues. Nothing is earth-shattering, just constant forward
progress for more devices supported and cleanups and small fixes:
- USB gadget driver updates and fixes
- new USB gadget driver for some hardware, followed by a quick revert
of those patches as they were not ready to be merged...
- PHY driver updates
- Lots of new driver additions and cleanups with a few fixes mixed in.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSXjYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynMYACgnSRP3GylwMywrkc9paVmDeiIgNwAn0N2sika
JEW7C3lkBJZJ7R6V/Ynm
=drla
-----END PGP SIGNATURE-----
Merge tag 'usb-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY updates from Greg KH:
"Here is the big USB and PHY driver pull request for 5.3-rc1.
Lots of stuff here, all of which has been in linux-next for a while
with no reported issues. Nothing is earth-shattering, just constant
forward progress for more devices supported and cleanups and small
fixes:
- USB gadget driver updates and fixes
- new USB gadget driver for some hardware, followed by a quick revert
of those patches as they were not ready to be merged...
- PHY driver updates
- Lots of new driver additions and cleanups with a few fixes mixed
in"
* tag 'usb-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (145 commits)
Revert "usb: gadget: storage: Remove warning message"
Revert "dt-bindings: add binding for USBSS-DRD controller."
Revert "usb:gadget Separated decoding functions from dwc3 driver."
Revert "usb:gadget Patch simplify usb_decode_set_clear_feature function."
Revert "usb:gadget Simplify usb_decode_get_set_descriptor function."
Revert "usb:cdns3 Add Cadence USB3 DRD Driver"
Revert "usb:cdns3 Fix for stuck packets in on-chip OUT buffer."
usb :fsl: Change string format for errata property
usb: host: Stops USB controller init if PLL fails to lock
usb: linux/fsl_device: Add platform member has_fsl_erratum_a006918
usb: phy: Workaround for USB erratum-A005728
usb: fsl: Set USB_EN bit to select ULPI phy
usb: Handle USB3 remote wakeup for LPM enabled devices correctly
drivers/usb/typec/tps6598x.c: fix 4CC cmd write
drivers/usb/typec/tps6598x.c: fix portinfo width
usb: storage: scsiglue: Do not skip VPD if try_vpd_pages is set
usb: renesas_usbhs: add a workaround for a race condition of workqueue
usb: gadget: udc: renesas_usb3: remove redundant assignment to ret
usb: dwc2: use a longer AHB idle timeout in dwc2_core_reset()
USB: gadget: function: fix issue Unneeded variable: "value"
...
While there are a mix of things here, most of the stuff
were written from Kernel developer's PoV. So, add them to
the driver-api book.
A follow up for this patch would be to move documents from
there that are specific to sysadmins, adding them to the
admin-guide.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kbuild documentation clearly shows that the documents
there are written at different times: some use markdown,
some use their own peculiar logic to split sections.
Convert everything to ReST without affecting too much
the author's style and avoiding adding uneeded markups.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
We have two *_CLASS_DEVICE kernel config options (LCD_CLASS_DEVICE
and BACKLIGHT_LCD_DEVICE) that do the same job.
The patch removes useless BACKLIGHT_LCD_SUPPORT option
and converts LCD_CLASS_DEVICE into a menu.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are a few remaining drivers/usb/ files that do not have SPDX
identifiers in them, all of these are either Kconfig or Makefiles. Add
the correct GPL-2.0 identifier to them to make scanning tools happy.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are USB2517 and USB2517i hubs, which have almost the same
registers space as already supported USB251xBi series. The difference
it in DIDs and in a few functions. This patch adds the USB2517/i data
structures to the driver, so it would have different setting depending
on the device discovered on i2c-bus.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a driver for configuration of the Microchip USB251xB/xBi
USB 2.0 hub controller series with USB 2.0 upstream connectivity, SMBus
configuration interface and two to four USB 2.0 downstream ports.
Furthermore add myself as a maintainer for this driver.
The datasheet can be found at the manufacturers website, see [1]. All
device-tree exposed configuration features have been tested on a i.MX6
platform with a USB2512B hub.
[1] http://ww1.microchip.com/downloads/en/DeviceDoc/00001692C.pdf
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a minimal driver to support bringing a usb4604 device
from microchip out of reset and into hub mode. The usb4604 device
is related to the usb3503 device, but it didn't seem close enough
to warrant putting both into the same file. This patch borrows
some of the usb3503 structure and trims it down to just handle
the optional reset gpio and adds the i2c command to put the
device into hub mode.
Datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/00001716A.pdf
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull HID updates from Jiri Kosina:
- new hid-alps driver for ALPS Touchpad-Stick device, from Masaki Ota
- much improved and generalized HID led handling, and merge of
specialized hid-thingm driver into this generic hid-led one, from
Heiner Kallweit
- i2c-hid power management improvements from Fu Zhonghui and Guohua
Zhong
- uhid initialization race fix from Roderick Colenbrander
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (21 commits)
HID: add usb device id for Apple Magic Keyboard
HID: hid-led: fix Delcom support on big endian systems
HID: hid-led: add support for Greynut Luxafor
HID: hid-led: add support for Delcom Visual Signal Indicator G2
HID: hid-led: remove report id from struct hidled_config
HID: alps: a few cleanups
HID: remove ThingM blink(1) driver
HID: hid-led: add support for ThingM blink(1)
HID: hid-led: add support for reading from LED devices
HID: hid-led: add support for devices with multiple independent LEDs
HID: i2c-hid: set power sleep before shutdown
HID: alps: match alps devices in core
HID: thingm: simplify debug output code
HID: alps: pass correct sizes to hid_hw_raw_request()
HID: alps: struct u1_dev *priv is internal to the driver
HID: add Alps I2C HID Touchpad-Stick support
HID: led: fix config
usb: misc: remove outdated USB LED driver
HID: migrate USB LED driver from usb misc to hid
HID: i2c_hid: enable i2c-hid devices to suspend/resume asynchronously
...
The USB LED driver exposes a undocumented sysfs interface and doesn't
use the standard kernel LED subsystem. It supports three devices:
Delcom Visual Signal Indicator
The driver supports generation 1 of the device only which was
manufactured until 2008. Remove support for this device completely.
Riso Kagaku RGB LED + Dream Cheeky Webmail Notifier
These devices are HID compliant and are supported by a new USB LED
driver under drivers/hid utilizing the kernel LED subsystem.
So let's remove the old USB LED driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for the Araneus Alea I USB hardware Random Number
Generator which is interfaced with in exactly the same way as the
Altus Metrum ChaosKey. We just add the appropriate device ID and
modify the config help text.
Signed-off-by: Bob Ham <bob.ham@collabora.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
USB Type-C Connector System Software Interface (UCSI) is
specification that defines the registers and data structures
that can be used to control USB Type-C ports on a system.
UCSI is used on several Intel Broxton SoC based platforms.
Things that UCSI can be used to control include at least USB
Data Role swapping, Power Role swapping and controlling of
Alternate Modes on top of providing general details about
the port and the partners that are attached to it.
The initial purpose of the UCSI driver is to make sure USB
is in host mode on desktop and server systems that are USB
dual role capable, and provide UCSI interface.
The goal is to integrate the driver later to an USB Type-C
framework for Linux kernel, and at the same time add support
for more extensive USB Type-C port control that UCSI offers,
for example data role swapping, power role swapping,
Alternate Mode control etc.
The UCSI specification is public can be obtained from here:
http://www.intel.com/content/www/us/en/io/universal-serial-bus/usb-type-c-ucsi-spec.html
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build errors when HW_RANDOM is not enabled:
drivers/built-in.o: In function `chaoskey_disconnect':
chaoskey.c:(.text+0x5f3f00): undefined reference to `hwrng_unregister'
drivers/built-in.o: In function `chaoskey_probe':
chaoskey.c:(.text+0x5f42a6): undefined reference to `hwrng_register'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a hardware random number generator. The driver provides both a
/dev/chaoskeyX entry and hooks the entropy source up to the kernel
hwrng interface. More information about the device can be found at
http://chaoskey.org
The USB ID for ChaosKey was allocated from the OpenMoko USB vendor
space and is visible as 'USBtrng' here:
http://wiki.openmoko.org/wiki/USB_Product_IDs
v2: Respond to review from Oliver Neukum <oneukum@suse.de>
* Delete extensive debug infrastructure and replace it with calls to
dev_dbg.
* Allocate I/O buffer separately from device structure to obey
requirements for non-coherant architectures.
* Initialize mutexes before registering device to ensure that open
cannot be invoked before the device is ready to proceed.
* Return number of bytes read instead of -EINTR when partial read
operation is aborted due to a signal.
* Make sure device mutex is unlocked in read error paths.
* Add MAINTAINERS entry for the driver
Signed-off-by: Keith Packard <keithp@keithp.com>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OTG3 and EH Compliance Plan 1.0 talks about Super Speed OTG Verification
system (SS-OVS) which consists of an excersizer and analyzer.
USB Compliance Suite from Lecroy or Ellisys can act as such SS-OVS for
Link Layer Validation (LVS).
Some modifications are needed for an embedded Linux USB host to pass all
these tests. Most of these tests require just Link to be in U0. They do
not work with default Linux USB stack since, default stack does port
reset and then starts sending setup packet, which is not expected by
Link Layer Validation (LVS) device of Lecroy Compliance Suit. Then,
There are many Link Layer Tests which need host to generate specific
traffic.
This patch supports specific traffic generation cases. As of now all the
host Lecroy Link Layer-USBIF tests (except TD7.26) passes
with this patch for single run using Lecroy USB Compliance Suite
Version 1.98 Build 239 and Lecroy USB Protocol Analyzer version 4.80
Build 1603. Therefore patch seems to be a good candidate for inclusion.
Further modification can be done on top of it.
lvstest driver will not bind to any device by default. It can bind
manually to a super speed USB host controller root hub. Therefore, regular
hub driver must be unbound before this driver is bound. For example, if
2-0:1.0 is the xhci root hub, then execute following to unbind hub driver.
echo 2-0:1.0 > /sys/bus/usb/drivers/hub/unbind
Then write Linux Foundation's vendor ID which is used by root hubs and
SS root hub's device ID into new_id file. Writing IDs into new_id file
will also bind the lvs driver with any available SS root hub interfaces.
echo "1D6B 3" > /sys/bus/usb/drivers/lvs/new_id
Now connect LVS device with root hub port.
Test case specific traffic can be generated as follows whenever needed:
1. To issue "Get Device descriptor" command for TD.7.06:
echo > /sys/bus/usb/devices/2-0\:1.0/get_dev_desc
2. To set U1 timeout to 127 for TD.7.18
echo 127 > /sys/bus/usb/devices/2-0\:1.0/u1_timeout
3. To set U2 timeout to 0 for TD.7.18
echo 0 > /sys/bus/usb/devices/2-0\:1.0/u2_timeout
4. To issue "Hot Reset" for TD.7.29
echo > /sys/bus/usb/devices/2-0\:1.0/hot_reset
5. To issue "U3 Entry" for TD.7.35
echo > /sys/bus/usb/devices/2-0\:1.0/u3_entry
6. To issue "U3 Exit" for TD.7.36
echo > /sys/bus/usb/devices/2-0\:1.0/u3_exit
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig entries for USB_U132_HCD and USB_FTDI_ELAN default to
(uppercase) "M". But in Kconfig (lowercase) "m" is a magic symbol. "M"
is an ordinary symbol. As "M" is never set these Kconfig symbols will
also not be set by default.
Since I'm not aware of a reason why these driver should be set by
default, let's just drop these lines (that basically do nothing).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB3503 driver had an incorrect depedency on REGMAP, instead of
REGMAP_I2C. This caused the build to fail since the necessary regmap
i2c pieces were not available.
Signed-off-by: Matthew Dawson <matthew@mjdsystems.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will give access to the diagnostic infrastructure regmap has but
the main point is to support future refactoring.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An Embedded Host High-Speed Electrical Test (EHSET) test fixture is
used to initiate test modes on a host controller in order to perform
the high speed electrical testing procedure for USB-IF compliance.
When this test fixture is connected to a host, it can enumerate as
one of several selectable VID/PID pairs, each corresponding to one
of the following test modes:
* TEST_SE0_NAK
* TEST_J
* TEST_K
* TEST_PACKET
* HS_HOST_PORT_SUSPEND_RESUME
* SINGLE_STEP_GET_DEV_DESC
* SINGLE_STEP_SET_FEATURE
The USB EHSET procedure can be found here:
http://www.usb.org/developers/onthego/EHSET_v1.01.pdf
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
[jackp@codeaurora.org: imported from commit 073c9409 on codeaurora.org;
minor cleanup and updated author email]
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the depends on USB from all config symbols in
drivers/usb/host/Kconfig and replace that with an if USB / endif block
as suggested by Alan Stern. Some source ... Kconfig lines have been
shuffled around to permit a better regroupment of the Kconfig files
depending on "config USB" item. No functionnal change is introduced.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds new driver of SMSC USB3503 USB 2.0 hub controller with HSIC
upstream connectivity and three USB 2.0 downstream ports. The specification
can be found from 'http://www.smsc.com/index.php?tid=295&pid=325'.
The current version have been tested very basic features switching the modes,
HUB-MODE and STANDBY-MODE.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an error during modpost, when ezusb is built into the kernel
while USB is built as module.
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Cc: stable <stable@vger.kernel.org>
--
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch
- moves drivers/usb/serial/ezusb.c to drivers/usb/misc/
- renamed CONFIG_USB_EZUSB to CONFIG_USB_EZUSB_FX2 to avoid build errors
- adapts Makefiles and Kconfigs switching from bool to tristate for CONFIG_USB_EZUSB_FX2
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Meywa-Denki/Kayac YUREX is a leg-shakes sensor device.
See http://bbu.kayac.com/en/about/ for further information.
This driver support read/write the leg-shakes counter in the device
via a device file /dev/yurex[0-9]*.
[minor coding style cleanups fixed by gregkh]
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the vstusb driver and support from the Linux tree.
This driver provided support for Vernier Software & Technology devices
and spectrometers (Ocean Optics). This driver is being replaced by a
user space - libusb - implementation.
Signed-off-by: Jim Collar <jim.collar@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Barry project's userspace program, bcharge, can better handle this
device and functionality, and it also works with the latest phones,
which this driver does not support. So remove it, as the userspace code
should be used instead.
Cc: Chris Frey <cdfrey@foursquare.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
THis patch (as1270) allows the usbtest module to be built even when
USB_DEVICEFS isn't configured. Tests can be performed without
USB_DEVICEFS, using the /dev/bus/usb/*/* device files.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the vstusb driver to the drivers/usb/misc directory.
This driver provides support for Vernier Software & Technology
spectrometers, all made by Ocean Optics. The driver provides both IOCTL
and read()/write() methods for sending raw data to spectrometers across
the bulk channel. Each method allows for a configured timeout.
From: Stephen Ware <stephen.ware@eqware.net>
Signed-off-by: Dennis O'Brien <dennis.obrien@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added basic support for a Delcom USB 7-segment LED Display
Signed-off by: Harrison Metzger <harrisonmetz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the auerswald USB driver from the linux kernel
2.6.26.
This driver was included into the kernel mainly to connect to the ISDN
framework. This was done in linux 2.4.x. For 2.6.x, due to the fragile
and moving ISDN support, this connection was never realized, and the
only use of this driver was for device configuration. In the age of DSL,
the demand of ISDN support is getting very low.
Meanwhile, with the advent of libusb, an userspace driver was done for
the device configuration which works fine for linux and mac. (Thanks to
the libusb developers!). The userspace driver is downloadable from the
auerswald web site.
So this driver is obsolete now and has to be removed. Many thanks to all
developers which helped me to bring this driver up and working.
Signed-off-by: Wolfgang Muees <wolfgang@iksw-muees.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: fix build bug in USB_ISIGHTFW
-tip tree testing found this build bug:
drivers/built-in.o: In function `isight_firmware_load':
isight_firmware.c:(.text+0x1ade08): undefined reference to `request_firmware'
isight_firmware.c:(.text+0x1adf9c): undefined reference to `release_firmware'
select FW_LOADER in USB_ISIGHTFW.
From: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Uninitialised Apple iSight drivers present with a distinctive USB ID.
Once firmware has been uploaded, they disconnect and reconnect with a
new ID. At this point they can be driven by the uvcvideo driver. As this
is unique to the Apple cameras and not functionality shared by any other
UVC devices, it makes sense to provide the firmware loading
functionality in a separate driver. This driver will read an isight.fw
file extracted from the Apple driver using the tools at
http://bersace03.free.fr/ift/ and upload it to the camera. It will also
handle the case where the device loses its firmware during hibernation
and must have it reloaded.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since nothing under the USB misc/ seems to be obviously experimental,
remove the EXPERIMENTAL dependency from those Kconfig entries.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ioctl is commented out for now, until we verify some userspace
application issues.
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Robert Marquardt <marquardt@codemercs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A simple driver to turn on the charging capability of a USB BlackBerry
device when it is plugged into the machine. It does not bind to the
device, so all userspace programs can still sync properly with it.
Note, if CONFIG_USB_SUSPEND is enabled, it can play havoc with this
device as the power to the port will be shut down. This device id will
have to be added to the global blacklist table when it is created.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's not a input driver, so it doesn't belong in the input directory.
Cc: Sam Hocevar <sam@zoy.org>
Cc: Dmitry Torokhov <dtor@insightbb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This "ftdi-elan" module is one half of the "driver" for
ELAN's Uxxx series adapters which are USB to PCMCIA CardBus
adapters. Currently only the U132 adapter is available and
it's module is called "u132-hcd".
When the USB hot plug subsystem detects a Uxxx series adapter
it should load this module.
Upon a successful device probe() the jtag device file interface
is created and the status workqueue started up.
The jtag device file interface exists for the purpose of
updating the firmware in the Uxxx series adapter, but as
yet it had never been used.
The status workqueue initializes the Uxxx and then sits there
polling the Uxxx until a supported PCMCIA CardBus device is
detected it will start the command and respond workqueues
and then load the module that handles the device. This will
initially be only the u132-hcd module. The status workqueue
then just polls the Uxxx looking for card ejects.
The command and respond workqueues implement a command
sequencer for communicating with the firmware on the other
side of the FTDI chip in the Uxxx. This "ftdi-elan" module
exports some functions to interface with the sequencer.
Note that this module is a USB client driver.
Note that the "u132-hcd" module is a (cut-down OHCI)
host controller.
Thus we have a topology with the parent of a host controller
being a USB client! This really stresses the USB subsystem
semaphore/mutex handling in the module removal.
Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for Ontrak ADU USB devices.
Fixed for printk issues by Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Steven Haigh <netwiz@crc.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch creates a device class phidget and add the phidget drivers to
them.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
