There is no need to put the IRQ number in driver's private platform
data structure as this can also be passed in struct i2c_lient.irq.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switch to generic media bus signal polarity flags and allow
configuring the FIELD signal polarity.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
FIELD signal is used for indicating frame field type to the frame grabber
in interlaced scan mode, as specified in ITU-R BT.601 standard.
In normal operation mode FIELD = 0 selects Field1 (odd) and FIELD = 1
selects Field2 (even). When the FIELD signal is inverted it's the other
way around.
Add corresponding flags for configuring the FIELD signal polarity,
V4L2_MBUS_FIELD_EVEN_HIGH for the standard (non-inverted) case and
V4L2_MBUS_FIELD_EVEN_LOW for inverted case.
Also add a comment about usage of V4L2_MBUS_[HV]SYNC* flags for
the hardware that uses [HV]REF signals.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The protocol differs by having two toggle bits in the scancode. Since
one of the bits is otherwise unused, we can safely handle the bits
unconditionally.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The keycode mangling algorithm is kept the same, so the new external
keymap has the same values as the old static table.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The MT9T001 is a parallel 3MP sensor from Aptina (formerly Micron)
controlled through I2C.
The driver creates a V4L2 subdevice. It currently supports binning and
cropping, and the gain, exposure, test pattern and black level controls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is now not needed as the sensor identification is done
through the media controller API.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The problem tackled in this patch is how to handle volatile autoclusters
correctly. A volatile autocluster is a cluster of related controls where one
control is the control that toggles between manual and auto mode and the other
controls are the values for the manual mode. For example autogain and gain,
autoexposure and exposure, etc.
If the hardware lets you read out the automatically calculated manual values
while in automode, then those manual controls should be marked volatile.
gain value as calculated by the autogain circuitry, then you would mark the
gain control as volatile (i.e. continuously changing).
The question in such use cases is what to do when switching from the auto
mode to the manual mode. Should we switch to the last set manual values or
should the volatile values be copied and used as the initial manual values.
For example: suppose the mode is manual gain and gain is set to 5. Then
autogain is turned on and the gain is set by the hardware to 2. Finally
the user switches back to manual gain. What should the gain be? 2 or 5?
After a long discussion the decisions was made to keep the last value as
calculated by the auto mode (so 2 in the example above).
The reason is that webcams that do such things will adapt themselves to
the current light conditions and when you switch back to manual mode you
expect that you keep the same picture. If you would switch back to old
manual values, then that would give you a suddenly different picture,
which is jarring for the user.
Additionally, this would be difficult to implement in applications that
store and restore the control values at application exit and start.
If you want to keep the old manual values when you switch from auto to
manual, then there would have to be a way for applications to get hold
of those old values while in auto mode, but there isn't.
So this patch will do all the heavy lifting in v4l2-ctrls.c: if you go
from auto mode to manual mode and the manual controls are volatile, then
g_volatile_ctrl will be called to get the current values for the manual
controls before switching to manual mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the new flag there is no need anymore to have a separate is_volatile
field. Modify all users to use the new flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in include/.
This patch removes them.
When I last posted the patch, the ceph bit was ACK'ed by Sage Weil, so
I've added that below.
The pwc-ioctl change generated quite a bit of discussion about V4L version
numbers in general, but as far as I can tell, no concensus was reached on
what the long term solution should be, so in the mean time I think we
could start by just removing the unneeded include, which is why I'm
resending the patch with that hunk still included.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Sage Weil <sage@newdream.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The MT9P031 is a parallel 12-bit 5MP sensor from Aptina (formerly
Micron) controlled through I2C.
The driver creates a V4L2 subdevice. It currently supports skipping,
cropping, automatic binning, and gain, exposure, h/v flip and test
pattern controls.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/omap3isp/isp.h is not a proper location for a header
that needs to be included from board code. Move the platform data
definitions to media/omap3isp.h.
Board code still needs to include isp.h to get the struct isp_device
definition and access OMAP3 ISP platform callbacks. Those callbacks will
be replaced by more generic code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a top level media device driver aggregating FIMC video devnodes,
MIPI-CSIS and sensor subdevs. This driver gathers all media entities
and creates the possible links between them during initialization. By
default some links will be activated to enable access to all available
sensors in the system. For example if there are sensors S0, S1 listed
in the media device platform data definition they will be by default
assigned to FIMC0, FIMC1 respectively, which in turn will corresponds
to separate /dev/video?.
There is enough FIMC H/W entities to cover all available physical camera
interfaces in the system.
The fimc media device driver is bound to the "s5p-fimc-md" platform device.
Such platform device should be created by board initialization code
and camera sensors description array need to be specified as its
platform data.
The media device driver also implements various video pipeline operations,
for enabling subdevs power, streaming, etc., which will be used by the
capture video node driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch changes the order of operations during stream on call. Now the
buffers are first queued to the driver and then the start_streaming method
is called.
This resolves the most common case when the driver needs to know buffer
addresses to enable dma engine and start streaming. Additional parameter
to start_streaming method have been added to simplify drivers code. The
driver are now obliged to check if the number of queued buffers is high
enough to enable hardware streaming. If not - it can return an error. In
such case all the buffers that have been pre-queued are invalidated.
This patch also updates all videobuf2 clients to work properly with the
changed order of operations.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
CC: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
CC: Hans Verkuil <hverkuil@xs4all.nl>
CC: Tomasz Stanislawski <t.stanislaws@samsung.com>
CC: Sylwester Nawrocki <s.nawrocki@samsung.com>
CC: Kamil Debski <k.debski@samsung.com>
CC: Jonathan Corbet <corbet@lwn.net>
CC: Josh Wu <josh.wu@atmel.com>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Paul Mundt <lethal@linux-sh.org>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the correct 'dma_addr' name for the buffer address. 'paddr' suggested
that this is the physical address in system memory. For most ARM platforms
these two are the same, but this is not a generic rule. 'dma_addr' will
also point better to dma-mapping api.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Plane sizes array was declared as unsigned long[], while unsigned int is
more than enough for storing size of the video buffer. This patch reduces
the size of the array by definiting it as unsigned int[].
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MAPPED flag was set for the buffer only if all it's planes were mapped and
relied on a simple mapping counter. This assumption is really bogus,
especially because the buffers may be mapped multiple times. Also the
meaning of this flag for muliplane buffers was not really useful. This
patch fixes this issue by setting the MAPPED flag for the buffer if any of
it's planes is in use (what means that has been mapped at least once), so
MAPPED flag can be used as 'in_use' indicator.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Videobuf2 accepted any userptr buffer without verifying if its size is
large enough to store the video data from the driver. The driver reports
the minimal size of video data once in queue_setup and expects that
videobuf2 provides buffers that match these requirements. This patch
adds the required check.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Macros coded with if statements should be do { if... } while (0)
so the macros can be used in other if tests.
Use ##__VA_ARGS__ for variadic macro as well.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Standardize the mechanisms to emit logging messages.
A few other modules used an #include from saa7146,
convert those at the same time.
Add pr_fmt.
Convert printks to pr_<level>
Convert printks without KERN_<level> to appropriate pr_<level>.
Convert logging macros requiring multiple parentheses to normal style.
Removed embedded prefixes when pr_fmt was added.
Whitespace cleanups when around other conversions.
Use printf extension %pM to print mac address.
Coalesce format strings.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Michael Hunold <michael@mihu.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is an initial driver release for the Omnivision 5642 CMOS sensor.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that v4l2 subdevices have got their own device objects, having
one more device in soc-camera clients became redundant and confusing.
This patch removes those devices and the soc-camera bus, they used to
reside on.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The soc-camera bus is now completely local again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This moves us one more step closer to eliminating the soc-camera bus
and devices on it. Besides, as a side effect, CSI-2 runtime PM on
sh-mobile secomes finer grained now: we only have to power on the
interface, when the device nodes are open.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add media bus configuration types and two subdev operations to get
supported mediabus configurations and to set a specific configuration.
Subdevs can support several configurations, e.g., they can send video data
on 1 or several lanes, can be configured to use a specific CSI-2 channel,
in such cases subdevice drivers return bitmasks with all respective bits
set. When a set-configuration operation is called, it has to specify a
non-ambiguous configuration.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc-camera host drivers shall be implementing their PM, using standard
kernel methods, soc-camera specific hooks can die.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callback is used to acquire current analog TV standard from a subdev.
It is used to avoid keeping current standard in top-level driver.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callback is used to acquire current digital video preset from a subdev.
It is used to avoid keeping dv preset in top-level driver.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callback is used to acquire TV norms supported by a subdev.
It is used to avoid having standards in top-level driver.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the driver for the adp1653 LED flash controller. This
controller supports a high power led in flash and torch modes and an
indicator light, sometimes also called privacy light.
The adp1653 is used on the Nokia N900.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Tuukka Toivonen <tuukkat76@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David Cohen <dacohen@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's getting confusing who is linking to what, so add an overview at
the start of the header.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The implementation of VIDIOC_G/S/TRY_EXT_CTRLS in the control framework has
to figure out which controls in the control list belong to the same cluster.
Since controls belonging to the same cluster need to be handled as a unit,
this is important information.
It did that by going over the controls in the list and for each control that
belonged to a multi-control cluster it would walk the remainder of the list
to try and find controls that belong to that same cluster.
This approach has two disadvantages:
1) it was a potentially quadratic algorithm (although highly unlikely that
it would ever be that bad in practice).
2) it took place with the control handler's lock held.
Since we want to make it possible in the future to change control values
from interrupt context, doing a lot of work while holding a lock is not a
good idea.
In the new code the algorithm is no longer quadratic but linear in the
number of controls in the list. Also, it now can be done beforehand.
Another change that was made was to so the try and set at the same time.
Before when S_TRY_EXT_CTRLS was called it would 'try' the controls first,
and then it would 'set' them. The idea was that any 'try' errors would
prevent the 'set' from happening, thus avoiding having partially set
control lists.
However, this caused more problems than it solved because between the 'try'
and the 'set' changes might have happened, so it had to try a second time,
and since actual controls with a try_ctrl op are very rare (and those that
we have just adjust values and do not return an error), I've decided to
drop that two-stage approach and just combine try and set.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the event queue for a subscribed event is full, then the oldest
event is dropped. It would be nice if the contents of that oldest
event could be merged with the next-oldest. That way no information is
lost, only intermediate steps are lost.
This patch adds optional replace() (called when only one kevent was allocated)
and merge() (called when more than one kevent was allocated) callbacks that
will be called to do this job.
These two callbacks are implemented for the V4L2_EVENT_CTRL event.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver had to decide how many events to allocate when the v4l2_fh struct
was created. It was possible to add more events afterwards, but there was no
way to ensure that you wouldn't miss important events if the event queue
would fill up for that filehandle.
In addition, once there were no more free events, any new events were simply
dropped on the floor.
For the control event in particular this made life very difficult since
control status/value changes could just be missed if the number of allocated
events and the speed at which the application read events was too low to keep
up with the number of generated events. The application would have no idea
what the latest state was for a control since it could have missed the latest
control change.
So this patch makes some major changes in how events are allocated. Instead
of allocating events per-filehandle they are now allocated when subscribing an
event. So for that particular event type N events (determined by the driver)
are allocated. Those events are reserved for that particular event type.
This ensures that you will not miss events for a particular type altogether.
In addition, if there are N events in use and a new event is raised, then
the oldest event is dropped and the new one is added. So the latest event
is always available.
This can be further improved by adding the ability to merge the state of
two events together, ensuring that no data is lost at all. This will be
added in the next patch.
This also makes it possible to allow the user to determine the number of
events that will be allocated. This is not implemented at the moment, but
would be trivial.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2_ctrl_fh struct connected v4l2_ctrl with v4l2_fh so the control
would know which filehandles subscribed to it. However, it is much easier
to use struct v4l2_subscribed_event directly for that and get rid of that
intermediate struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that supported events used to be rare, but now that controls can also
raise events this will become much more common since almost all drivers have
controls.
This means that keeping struct v4l2_events as a separate struct make no more
sense. Merging it into struct v4l2_fh simplifies things substantially as it
is now an integral part of the filehandle struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes .enum_input(), .suspend() and .resume() soc-camera
client operations.
Functionality, provided by .enum_input(), if needed, can be implemented
using the v4l2-subdev API.
As for .suspend() and .resume(), the only client driver, implementing
these methods has been mt9m111, and the only host driver, using them
has been pxa-camera. Now that both those drivers have been converted
to the standard subdev .s_power() operation, .suspend() and .resume()
can be removed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SOCAM_MIPI_[1234]LANE flags are not board-specific sensor flags, they
are bus configuration flags.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Whenever a control changes value or state an event is sent to anyone
that subscribed to it.
This functionality is useful for control panels but also for applications
that need to wait for (usually status) controls to change value.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When an application changes a control you want to generate an event.
However, you want to avoid sending such an event back to the application
(file handle) that caused the change.
Add the filehandle to the various set control functions.
The filehandle isn't used yet, but the control event patches will need
this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is a bit tricky to handle autogain/gain type scenerios correctly. Such
controls need to be clustered and the V4L2_CTRL_FLAG_UPDATE should be set on
the autofoo controls. In addition, the manual controls should be marked
inactive when the automatic mode is on, and active when the manual mode is on.
This also requires specialized volatile handling.
The chances of drivers doing all these things correctly are pretty remote.
So a new v4l2_ctrl_auto_cluster function was added that takes care of these
issues.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is required to implement control events and is also needed to allow
for per-filehandle control handlers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the VENC or the Video encoder, which is responsible
for the blending of all source planes and timing generation for Video
modes like NTSC, PAL and other digital outputs. the VENC implementation
currently supports COMPOSITE and COMPONENT outputs and NTSC and PAL
resolutions through the analog DACs. The venc block is implemented
as a subdevice, allowing for additional external and internal encoders
of other kind to plug-in.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements the functionality of the OSD block
of the VPBE. The OSD in total supports 4 planes or Video
sources - 2 mainly RGB and 2 Video. The patch implements general
handling of all the planes, with specific emphasis on the Video
plane capabilities as the Video planes are supported through the
V4L2 driver.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements the core functionality of the display driver,
mainly controlling the VENC and other encoders, and acting as
the one point interface for the main V4L2 driver. This implements
the core of each of the V4L2 IOCTLs.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the display driver for Texas Instruments's DM644X family
SoC. This patch contains the main implementation of the driver with the
V4L2 interface. The driver implements the streaming model with
support for both kernel allocated buffers and user pointers. It also
implements all of the necessary IOCTLs necessary and supported by the
video display device.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch simplifies the platform data slightly, by removing
unused elements.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now we have a camera working over the marvell cam controller core. It
works like the cafe driver and has all the same limitations, contiguous DMA
only being one of them. But it's a start.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver will soon become a family of drivers, so let's give it its own
place to live. This move requires putting ov7670.h into include/media, but
there are no code changes.
Cc: Daniel Drake <dsd@laptop.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Durations can never be negative, so it makes sense to consistently use
unsigned int for LIRC transmission. Contrary to the initial impression,
this shouldn't actually change the userspace API.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is initial code written by Davide Ferri for the PCTV 340e, including
a new xc4000 driver. I am checking in all the code unmodified, and making
no assertions about its quality (other than confirming it compiles).
[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Davide Ferri <davidef1986@gmail.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner ops g_frequency, g_tuner and s_tuner require that the tuner type
field is filled in. Document this.
The tuner-core doc is based on a patch from Mauro Carvalho Chehab <mchehab@redhat.com>.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Store the cdev pointer in struct irctl, allocated dynamically as needed,
rather than having a static array. At the same time, recycle some of the
saved memory to nudge the maximum number of lirc devices supported up a
ways -- its not that uncommon these days, now that we have the rc-core
lirc bridge driver, to see a system with at least 4 raw IR receivers.
(consider a mythtv backend with several video capture devices and the
possible need for IR transmit hardware).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The name 'entity' is used twice in the macro body, once as the macro
argument, and once as a structure field name. This breaks compilation if
the macro is called with its argument not named 'entity'.
Fix this by renaming the macro argument '__e'. This should avoid
namespace clashes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
12-bit formats, similar to YUV 4:2:0 occupy 3 bytes for each two pixels
and cannot be described by any of the existing SOC_MBUS_PACKING_* macros.
This patch adds a new one SOC_MBUS_PACKING_1_5X8 to describe such
formats and extends soc_mbus_samples_per_pixel() to support it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Recently mediabus pixel format codes have become a part of the user-
space API, at which time their values also have been changed from
contiguous numbers, running from 0 to sparse numbers with values
around 0x1000, 0x2000, 0x3000... This made them unsuitable for the
use as array indices. This patch switches soc-camera internal format
look-ups to not depend on values of those macros.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an soc-camera host livecrop operation to implement live zoom. If
a host driver implements it, it should take care to preserve output
frame format, then live crop doesn't break streaming.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The MT9V032 is a parallel wide VGA sensor from Aptina (formerly Micron)
controlled through I2C.
The driver creates a V4L2 subdevice. It currently supports binning and
cropping, and the gain, auto gain, exposure, auto exposure and test
pattern controls.
Signed-off-by: Detlev Casanova <detlev.casanova@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (42 commits)
[media] media: vb2: correct queue initialization order
[media] media: vb2: fix incorrect v4l2_buffer->flags handling
[media] s5p-fimc: Add support for the buffer timestamps and sequence
[media] s5p-fimc: Fix bytesperline and plane payload setup
[media] s5p-fimc: Do not allow changing format after REQBUFS
[media] s5p-fimc: Fix FIMC3 pixel limits on Exynos4
[media] tda18271: update tda18271c2_rf_cal as per NXP's rev.04 datasheet
[media] tda18271: update tda18271_rf_band as per NXP's rev.04 datasheet
[media] tda18271: fix bad calculation of main post divider byte
[media] tda18271: prog_cal and prog_tab variables should be s32, not u8
[media] tda18271: fix calculation bug in tda18271_rf_tracking_filters_init
[media] omap3isp: queue: Don't corrupt buf->npages when get_user_pages() fails
[media] v4l: Don't register media entities for subdev device nodes
[media] omap3isp: Don't increment node entity use count when poweron fails
[media] omap3isp: lane shifter support
[media] omap3isp: ccdc: support Y10/12, 8-bit bayer fmts
[media] media: add missing 8-bit bayer formats and Y12
[media] v4l: add V4L2_PIX_FMT_Y12 format
cx23885: Fix stv0367 Kconfig dependency
[media] omap3isp: Use isp xclk defines
...
Fix up trivial conflict (spelink errurs) in drivers/media/video/omap3isp/isp.c
dma_addr_t may not fit into void* on some architectures. To be safe, make
vb2_dma_contig_cookie() return a pointer to dma_addr_t and dereference it
in vb2_dma_contig_plane_paddr() back to dma_addr_t.
Signed-off-by: Pawel Osciak <pawel@osciak.com>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes the problem in which a host driver
sets a personalized sizeimage or bytesperline field,
and gets ignored when doing G_FMT.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are two "hauppauge-new" keymaps, one with protocol
unknown, and the other with the protocol marked accordingly.
However, both tables are miss-named.
Also, the old rc-hauppauge-new is broken, as it mixes
three different controllers as if they were just one.
This patch solves half of the problem by renaming the
correct keycode table as just rc-hauppauge. This table
contains the codes for the four different types of
remote controllers found on Hauppauge cards, properly
mapped with their different addresses.
create mode 100644 drivers/media/rc/keymaps/rc-hauppauge.c
delete mode 100644 drivers/media/rc/keymaps/rc-rc5-hauppauge-new.c
[Jarod: fix up RC_MAP_HAUPPAUGE defines]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Rather than guess which driver supports core priority handling, require drivers
that do to explicitly set the V4L2_FL_USE_FH_PRIO flag in video_device.
Updated the core prio handling accordingly and set the flag in the three
drivers that do.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video_device struct has proper ref counting and its release function
will be called when the last user releases it. But no such support was
available for struct v4l2_device. This made it hard to determine when a
USB driver can release the device if it has multiple device nodes.
With one device node it is easy of course, since when the device node is
released, the whole device can be released.
This patch adds refcounting to v4l2_device. When registering device nodes
the v4l2_device refcount will be increased, when releasing device nodes
it will be decreased. The (optional) release function will be called when
the last device node was released.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that use v4l2_fh can now use the core framework support of g/s_priority.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several drivers need to do something when the first filehandle is opened
or the last filehandle is closed. Most implement some use count mechanism,
but if they use v4l2_fh, then you can also just check if this is the only
filehandle for the device node. A simple helper function can do this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add two new functions: v4l2_fh_open allocates and initializes a struct v4l2_fh
based on a struct file pointer and v4l2_fh_release releases and frees a struct
v4l2_fh.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Integrate the v4l2_prio_state into the core, ready for use.
One struct v4l2_prio_state is added to v4l2_device and a pointer
to a prio state is added to video_device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We are going to move priority handling into the v4l2 core. As a consequence
the v4l2_prio helper functions need to be moved into the core videodev
module as well to prevent circular dependencies.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remote used for TerraTec Cinergy T Stick RC.
Keytable from Martin Groszhauser <mgroszhauser@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Martin Groszhauser <mgroszhauser@gmail.com>
Cc: TerraTux <TerraTux@terratec.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow the MIPI-CSI data alignment to be defined in the board setup
as it may be different across various camera sensors.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add num_clients field to struct s5p_fimc_isp_info to define exactly
size of clients array which simplifies a bit the sensors management.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some buggy sensors generate corrupt frames when the stream is started.
This new operation return the number of corrupt frames to skip when
starting the stream.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the VIDIOC_SUBDEV_S_CROP and G_CROP ioctls to the
userland API. CROPCAP is not implemented because it's redundant.
Signed-off-by: Antti Koskipaa <akoskipa@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The three new ioctl VIDIOC_SUBDEV_ENUM_FRAME_INTERVAL,
VIDIOC_SUBDEV_G_FRAME_INTERVAL and VIDIOC_SUBDEV_S_FRAME_INTERVAL can be
used to enumerate and configure a subdev's frame rate from userspace.
Two new video::g/s_frame_interval subdev operations are introduced to
support those ioctls. The existing video::g/s_parm operations are
deprecated and shouldn't be used anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a userspace API to get, set and enumerate the media format on a
subdev pad.
The format at the output of a subdev usually depends on the format at
its input(s). The try format operation is thus not suitable for probing
format at individual pads, as it can't modify the device state and thus
can't remember the format tried at the input to compute the output
format.
To fix the problem, pass an extra argument to the get/set format
operations to select the 'try' or 'active' format.
The try format is used when probing the subdev. Setting the try format
must not change the device configuration but can store data for later
reuse. Data storage is provided at the file-handle level so applications
probing the subdev concurently won't interfere with each other.
The active format is used when configuring the subdev. It's identical to
the format handled by the usual get/set operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a v4l2_subdev_pad_ops structure for the operations that need to be
performed at the pad level such as format-related operations.
Pad format-related operations use v4l2_mbus_framefmt instead of
v4l2_format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 sub-devices store pad formats and crop settings in the file handle.
To let drivers initialize those settings properly, add an open operation
that is called when the subdev is opened as well as a corresponding
close operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Used for storing subdev information per file handle and hold V4L2 file
handle.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Antti Koskipaa <akoskipa@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The header defines the v4l2_mbus_framefmt structure which will be used
by the V4L2 subdevs userspace API.
Change the type of the v4l2_mbus_framefmt::code field to __u32, as enum
sizes can differ between different ABIs on the same architectures.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 subdevices are media entities. As such they need to inherit from
(include) the media_entity structure.
When registering/unregistering the subdevice, the media entity is
automatically registered/unregistered. The entity is acquired on device
open and released on device close.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 devices are media entities. As such they need to inherit from
(include) the media_entity structure.
When registering/unregistering the device, the media entity is
automatically registered/unregistered. The entity is acquired on device
open and released on device close.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The pointer will later be used to register/unregister media entities
when registering/unregistering a v4l2_subdev or a video_device.
With the introduction of media devices, device drivers need to store a
pointer to a driver-specific structure in the device's drvdata.
v4l2_device can't claim ownership of the drvdata anymore.
To maintain compatibility with drivers that rely on v4l2_device storing
a pointer to itself in the device's drvdata, v4l2_device_register() will
keep doing so if the drvdata is NULL.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers often need to associate pipeline objects to entities, and to
take stream state into account when configuring entities and links. The
pipeline API helps drivers manage that information.
When starting streaming, drivers call media_entity_pipeline_start(). The
function marks all entities connected to the given entity through
enabled links, either directly or indirectly, as streaming. Similarly,
when stopping the stream, drivers call media_entity_pipeline_stop().
The media_entity_pipeline_start() function takes a pointer to a media
pipeline and stores it in every entity in the graph. Drivers should
embed the media_pipeline structure in higher-level pipeline structures
and can then access the pipeline through the media_entity structure.
Link configuration will fail with -EBUSY by default if either end of the
link is a streaming entity, unless the link is marked with the
MEDIA_LNK_FL_DYNAMIC flag.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create the following ioctl and implement it at the media device level to
setup links.
- MEDIA_IOC_SETUP_LINK: Modify the properties of a given link
The only property that can currently be modified is the ENABLED link
flag to enable/disable a link. Links marked with the IMMUTABLE link flag
can not be enabled or disabled.
Enabling or disabling a link has effects on entities' use count. Those
changes are automatically propagated through the graph.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create the following two ioctls and implement them at the media device
level to enumerate entities, pads and links.
- MEDIA_IOC_ENUM_ENTITIES: Enumerate entities and their properties
- MEDIA_IOC_ENUM_LINKS: Enumerate all pads and links for a given entity
Entity IDs can be non-contiguous. Userspace applications should
enumerate entities using the MEDIA_ENT_ID_FLAG_NEXT flag. When the flag
is set in the entity ID, the MEDIA_IOC_ENUM_ENTITIES will return the
next entity with an ID bigger than the requested one.
Only forward links that originate at one of the entity's source pads are
returned during the enumeration process.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to the wide differences between drivers regarding power management
needs, the media controller does not implement power management.
However, the media_entity structure includes a use_count field that
media drivers can use to track the number of users of every entity for
power management needs.
The use_count field is owned by media drivers and must not be touched by
entity drivers. Access to the field must be protected by the media
device graph_mutex lock.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add media entity graph traversal. The traversal follows enabled links by
depth first. Traversing graph backwards is prevented by comparing the next
possible entity in the graph with the previous one. Multiply connected
graphs are thus not supported.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As video hardware pipelines become increasingly complex and
configurable, the current hardware description through v4l2 subdevices
reaches its limits. In addition to enumerating and configuring
subdevices, video camera drivers need a way to discover and modify at
runtime how those subdevices are connected. This is done through new
elements called entities, pads and links.
An entity is a basic media hardware building block. It can correspond to
a large variety of logical blocks such as physical hardware devices
(CMOS sensor for instance), logical hardware devices (a building block
in a System-on-Chip image processing pipeline), DMA channels or physical
connectors.
A pad is a connection endpoint through which an entity can interact with
other entities. Data (not restricted to video) produced by an entity
flows from the entity's output to one or more entity inputs. Pads should
not be confused with physical pins at chip boundaries.
A link is a point-to-point oriented connection between two pads, either
on the same entity or on different entities. Data flows from a source
pad to a sink pad.
Links are stored in the source entity. To make backwards graph walk
faster, a copy of all links is also stored in the sink entity. The copy
is known as a backlink and is only used to help graph traversal.
The entity API is made of three functions:
- media_entity_init() initializes an entity. The caller must provide an
array of pads as well as an estimated number of links. The links array
is allocated dynamically and will be reallocated if it grows beyond the
initial estimate.
- media_entity_cleanup() frees resources allocated for an entity. It
must be called during the cleanup phase after unregistering the entity
and before freeing it.
- media_entity_create_link() creates a link between two entities. An
entry in the link array of each entity is allocated and stores pointers
to source and sink pads.
When a media device is unregistered, all its entities are unregistered
automatically.
The code is based on Hans Verkuil <hverkuil@xs4all.nl> initial work.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The media_device structure abstracts functions common to all kind of
media devices (v4l2, dvb, alsa, ...). It manages media entities and
offers a userspace API to discover and configure the media device
internal topology.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The media_devnode structure provides support for registering and
unregistering character devices using a dynamic major number. Reference
counting is handled internally, making device drivers easier to write
without having to solve the open/disconnect race condition issue over
and over again.
The code is based on video/v4l2-dev.c.
[mchehab@redhat.com: Remove linux/smp_lock.h include to not break compilation on bisect]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide v4l2_subdevs with v4l2_event support. Subdev drivers only need very
little to support events.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David Cohen <dacohen@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function isn't small or performance sensitive enough to be inlined.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create a device node named subdevX for every registered subdev.
As the device node is registered before the subdev core::s_config
function is called, return -EGAIN on open until initialization
completes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no reason to require subdevices to implement the core
operations. Remove the check for non-NULL core operations when
initializing the subdev.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vb2_get_plane_payload() gets the bytesused field for a plane, it doesn't
set it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds audio DMA capture and ALSA mixer elements for the line
input jack of the Hauppauge Nova-S-plus DVB-S PCI card. The Nova-S-plus
has a WM8775 ADC that is currently not detected. This patch enables
this chip and exports volume, balance mute and ALC elements for ALSA
mixer controls.
[mchehab@redhat.com: Changed the patch to only talk with wm8775 if board
info says so. Also, added platform_data support, to avoid changing the
behaviour for other boards, and fixed CodingStyle]
[awalls@md.metrocast.net: Changed patch to make the WM8775_GID defintion
bridge driver private and let the bridge driver set the value of
v4l2_subdev.grp_id.]
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
This soc_camera driver is for Omnivision's OV9740 sensor. This initial
submission provides support for YUV422 output at 1280x720 (720p), which is
the sensor's native resolution. 640x480 (VGA) is also supported, with
cropping and scaling performed by the sensor's ISP.
This driver is heavily based off of the existing OV9640 driver.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Extend soc-camera core to also support the videobuf2 API.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a function to calculate the number of samples on the media-bus,
required to retrieve one pixel of a certain format.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda9887 used to use the T_STANDBY type internally, while tea5761
used it to put the device to sleep. Fix the code for it to work
properly with the tuner core changes and remove this flag from
tuner.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the past, T_STANDBY were used on devices with a separate radio tuner to
mark a tuner that were disabled. With the time, it got newer meanings.
Also, due to a bug at the logic, the driver might incorrectly return
T_STANDBY to userspace.
So, instead of keeping the abuse, just use a boolean for storing
such information.
We can't remove T_STANDBY yet, as this is used on two other drivers. A
latter patch will address its usage outside tuner-core.
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add I2C/V4L2 subdev driver for Siliconfile NOON010PC30 CIF camera.
The driver implements basic functionality, i.e. CIF/QCIF/QQCIF
resolution and color format selection, automatic/manual color
balance control. Other functions like cropping, rotation/flip,
exposure etc. can be easily implemented if needed.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add ID for NOON010PC30 camera chip and reserve ID range for
Siliconfile sensors.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Manage the camera sensor clock in the host driver rather than
leaving this task for sensor drivers. The clock frequency
must be passed in the sensor's and host driver's platform data.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove bus_width from s5p_fimc_isp_info data structure.
Determine camera data bus width based on mediabus pixel format.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change s3c_fimc.h header file name to s5p_fimc.h, replace s3c_fimc_*
names with s5p_fimc_*. s3c_fimc need to be reserved for S3C series
and s5p-fimc driver will not cover CAMIF devices in S3C SoC series.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Port memory-to-memory framework to videobuf2 framework.
Add support for multi-planar Video for Linux 2 API extensions to the
memory-to-memory driver framework.
Based on the original patch written by Pawel Osciak.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a generic file io (read and write) emulator for videobuf2. It uses
MMAP memory type buffers and generic vb2 calls: req_bufs, qbuf and
dqbuf. Video date is being copied from mmap buffers to userspace with
standard copy_to_user() function. To add support for file io the driver
needs to provide an additional callback - read_setup or write_setup. It
should provide the default number of buffers used by emulator and flags.
With these flags one can detemine the style of read() or write()
emulation. By default 'streaming' style is used. With
VB2_FILEIO_READ_ONCE flag one can select 'one shot' mode for read()
emulator. With VB2_FILEIO_WRITE_IMMEDIATE flag one can select immediate
conversion of write calls to qbuf for write() emulator, so the vb2 will
not wait until each buffer is filled completely before queueing it to
the driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an implementation of DMA scatter/gather allocator and handling
routines for videobuf2.
For mmap operation mode it is implemented on top of
alloc_page + sg_set_page/_free_page.
For userptr operation mode it is implemented on top of
get_user_pages + sg_set_page/put_page.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an implementation of DMA coherent memory allocator and handling
routines for videobuf2, implemented on top of dma_alloc_coherent() call.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an implementation of contiguous virtual memory allocator and handling
routines for videobuf2, implemented on top of vmalloc()/vfree() calls.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Videobuf2 is a Video for Linux 2 API-compatible driver framework for
multimedia devices. It acts as an intermediate layer between userspace
applications and device drivers. It also provides low-level, modular
memory management functions for drivers.
Videobuf2 eases driver development, reduces drivers' code size and aids in
proper and consistent implementation of V4L2 API in drivers.
Videobuf2 memory management backend is fully modular. This allows custom
memory management routines for devices and platforms with non-standard
memory management requirements to be plugged in, without changing the
high-level buffer management functions and API.
The framework provides:
- implementations of streaming I/O V4L2 ioctls and file operations
- high-level video buffer, video queue and state management functions
- video buffer memory allocation and management
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is adding support for Technisat's new USB2.0 DVB-S/S2 receiver
device. The development was sponsored by Technisat.
The Green led is toggle depending on the frontend-state. The Red LED is turned
on all the time.
The MAC address reading from the EEPROM along with the
LRC-method to check whether its valid.
Support for the IR-receiver of the Technisat USB2 box. The keys of
small, black remote-control are built-in, repeated key behaviour are
simulated.
The i2c-mutex of the dvb-usb-structure is used as a general mutex for
USB requests, as there are 3 threads racing for atomic requests
consisting of multiple usb-requests.
A module option is there which disables the toggling of LEDs by the
driver on certain triggers. Useful when being used in a "dark"
environment.
[mchehab@redhat.com: Fix merge conflicts with RC renaming patches]
Signed-off-by: Martin Wilks <m.wilks@technisat.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The later makes extensive use of structures defined in the former.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ene_ir driver was using a private define of MS_TO_NS, which is meant
to be microseconds to nanoseconds. The mceusb driver copied it,
intending to use is a milliseconds to microseconds. Lets move the
defines to a common location, expand and standardize them a touch, so
that we now have:
MS_TO_NS - milliseconds to nanoseconds
MS_TO_US - milliseconds to microseconds
US_TO_NS - microseconds to nanoseconds
Reported-by: David Härdeman <david@hardeman.nu>
CC: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Renamed has_new to is_new.
Drivers can use the is_new field to determine if a new value was specified
for a control. The v4l2_ctrl_handler_setup() must always set this to 1 since
the setup has to force a full update of all controls.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some subdevs need to call into the board code after they are registered
and have a valid struct v4l2_device pointer. The s_config op was abused
for this, but now that it is removed we need a cleaner way of solving this.
So this patch adds a struct with internal ops that the v4l2 core can call.
Currently only two ops exist: register and unregister. Subdevs can implement
these to call the board code and pass it the v4l2_device pointer, which the
board code can then use to get access to the struct that embeds the
v4l2_device.
It is expected that in the future open and close ops will also be added.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The core.s_config op was meant for legacy drivers that needed to work with old
pre-2.6.26 kernels. This is no longer relevant. Unfortunately, this op was
incorrectly called from several drivers.
Replace those occurences with proper i2c_board_info structs and call
v4l2_i2c_new_subdev_board.
After these changes v4l2_i2c_new_subdev_cfg() was no longer used, so remove
that function as well.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert saa7146 to use core-assisted locking.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems that cx88 and ivtv use wm8775 on some different modes. The
patch that added support for a board with wm8775 broke ivtv boards with
this device. As we're too close to release 2.6.37, let's just revert
it.
Reported-by: Andy Walls <awalls@md.metrocast.net>
Reported-by: Eric Sharkey <eric@lisaneric.org>
Reported-by: Auric <auric@aanet.com.au>
Reported by: David Gesswein <djg@pdp8online.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In certain machines, camera devices are supplied directly
by a number of regulators. This patch add the ability to drive
these regulators directly by the soc_camera driver.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This prevents checkpatch warnings generated when defining
'static const char *foo[]' arrays. It makes sense to use
const char * const * anyway since the pointers in the array
are indeed const.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove bt819.h from ioctl-number.txt and make a note in the header
that these ioctls are for internal use only.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The naming of the media/rds.h header suggested that it was a generic
RDS header, when in fact it is just a saa6588 module API that is
internal to the kernel.
Rename the header and the struct and defines in it to make this clear.
Also removed the header include in radio-si470x.h (not used anymore)
and from ioctl-number.txt (it's internal to the kernel and never called
from userspace).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no sense on keeping it on 2.6.38, as nobody is using it
anymore, at the kernel tree, and installing it at the userspace
API.
As two deprecated drivers still need it, move it to their internal
directories.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix some minor comments etc which are leftover from the old naming scheme.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remote keytables had different names all over the place. Part of the fault
is due to a bad naming when rc subsystem was created, but there were lots
of old names that were still here.
Use a common standard for everything.
Patch generated by this script:
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_scancode,rc_map_table,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_codes_,rc_map_,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_key_map,rc_map_table,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_map_table_size,rc_map_size,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The struct that describes a rc mapping had an weird and long name.
We should properly name it, to make easier for developers to work
with it, and to avoid confusion.
Basically, generated by this script:
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_scancode_table,rc_map,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_tab,rc_map,g <$i >a && mv a $i; done
(and manually fixed where needed)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,IR_TYPE,RC_TYPE,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_type,rc_type,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Remote Controller subsystem is meant to be used not only by Infra Red
but also for similar types of Remote Controllers. The core is not specific
to Infra Red. As such, rename:
- ir-core.h to rc-core.h
- IR_CORE to RC_CORE
- namespace inside rc-core.c/rc-core.h
To be consistent with the other changes.
No functional change on this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the timberdale video-in driver.
The video IP of timberdale delivers the video data via DMA.
The driver uses the DMA api to handle DMA transfers, and make use
of the V4L2 video buffers to handle buffers against user space.
If available the driver uses an encoder to get/set the video standard
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several fields on rc_dev that drivers can benefit. Allow drivers
to pass it as a parameter to the driver.
For now, the rc_dev parameter is optional. If drivers don't pass it, create
them internally. However, the best is to create rc_dev inside the drivers,
in order to fill other fields, like open(), close(), driver_name, etc.
So, a latter patch making it mandatory and changing the caller drivers is
welcome.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch merges the ir_input_dev and ir_dev_props structs into a single
struct called rc_dev. The drivers and various functions in rc-core used
by the drivers are also changed to use rc_dev as the primary interface
when dealing with rc-core.
This means that the input_dev is abstracted away from the drivers which
is necessary if we ever want to support multiple input devs per rc device.
The new API is similar to what the input subsystem uses, i.e:
rc_device_alloc()
rc_device_free()
rc_device_register()
rc_device_unregister()
[mchehab@redhat.com: Fix compilation on mceusb and cx231xx, due to merge conflicts]
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: this patch were originally bundled with some renaming
stuff and with the file merges, as seen at:
https://patchwork.kernel.org/patch/291092/.
Instead of using the original approach, I wrote the rename patches and the
code merge as separate changes, then applied the difference on this patch.
This way, it is easier to see the real changes at the code, and will be easier
to merge upstream, especially if some conflict rises on the renaming patches]
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx88 only depends on VIDEO_IR because it needs ir_extract_bits().
Move that function to ir-core.h and make it inline.
Lots of drivers had dependencies on VIDEO_IR when they really
wanted IR_CORE.
The only remaining drivers to depend on VIDEO_IR are bt8xx and
saa7134 (ir_rc5_timer_end is the only function exported by
ir-functions).
Rename VIDEO_IR -> IR_LEGACY to give a hint to anyone writing or
converting drivers to IR_CORE that they do not want a dependency
on IR_LEGACY.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the remaining usages of the ir_input_nokey() and
ir_input_keydown() functions provided by drivers/media/IR/ir-functions.c
by using the corresponding functionality in ir-core instead.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the cx88 driver (for sampling hw) to use the
decoders provided by ir-core instead of the separate ones provided
by ir-functions (and gets rid of those).
The value for MO_DDS_IO had a comment saying it corresponded to
a 4kHz samplerate. That comment was unfortunately misleading. The
actual samplerate was something like 3250Hz.
The current value has been derived by analyzing the elapsed time
between interrupts for different values (knowing that each interrupt
corresponds to 32 samples).
Thanks to Mariusz Bialonczyk <manio@skyboo.net> for testing my patches
(about one a day for two weeks!) on actual hardware.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the driver to use regulator framework instead of set_power callback.
This with gpio_reset platform data provide cleaner way to manage chip VIO,
VDD and reset signal inside the driver.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] gspca - sonixj: Better handling of the bridge registers 0x01 and 0x17
[media] gspca - sonixj: Add the bit definitions of the bridge reg 0x01 and 0x17
[media] gspca - sonixj: Set the flag for some devices
[media] gspca - sonixj: Add a flag in the driver_info table
[media] gspca - sonixj: Fix a bad probe exchange
[media] gspca - sonixj: Move bridge init to sd start
[media] bttv: remove unneeded locking comments
[media] bttv: fix mutex use before init (BZ#24602)
[media] Don't export format_by_forcc on two different drivers
Drivers should append their name on exported symbols, to avoid
conflicts with allyesconfig:
drivers/staging/built-in.o: In function `format_by_fourcc':
/home/v4l/work_trees/linus/drivers/staging/cx25821/cx25821-video.c:96: multiple definition of `format_by_fourcc'
drivers/media/built-in.o:/home/v4l/work_trees/linus/drivers/media/common/saa7146_video.c:88: first defined here
Let's rename both occurences with a small shellscript:
for i in drivers/staging/cx25821/*.[ch]; do sed s,format_by_fourcc,cx25821_format_by_fourcc,g <$i >a && mv a $i; done
for i in drivers/media/common/saa7146*.[ch]; do sed s,format_by_fourcc,saa7146_format_by_fourcc,g <$i >a && mv a $i; done
for i in include/media/saa7146*.[ch]; do sed s,format_by_fourcc,saa7146_format_by_fourcc,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The BKL replacement mutex had some serious performance side-effects on
V4L drivers. It is replaced by a better heuristic that works around the
worst of the side-effects.
Read the v4l2-dev.c comments for the whole sorry story. This is a
temporary measure only until we can convert all v4l drivers to use
unlocked_ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The argument isn't used anymore by the functions, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (505 commits)
[media] af9015: Fix max I2C message size when used with tda18271
[media] IR: initialize ir_raw_event in few more drivers
[media] Guard a divide in v4l1 compat layer
[media] imon: fix nomouse modprobe option
[media] imon: remove redundant change_protocol call
[media] imon: fix my egregious brown paper bag w/rdev/idev split
[media] cafe_ccic: Configure ov7670 correctly
[media] ov7670: allow configuration of image size, clock speed, and I/O method
[media] af9015: support for DigitalNow TinyTwin v3 [1f4d:9016]
[media] af9015: map DigitalNow TinyTwin v2 remote
[media] DigitalNow TinyTwin remote controller
[media] af9015: RC fixes and improvements
videodev2.h.xml: Update to reflect the latest changes at videodev2.h
[media] v4l: document new Bayer and monochrome pixel formats
[media] DocBook/v4l: Add missing formats used on gspca cpia1 and sn9c2028
[media] firedtv: add parameter to fake ca_system_ids in CA_INFO
[media] tm6000: fix a macro coding style issue
tm6000: Remove some ugly debug code
[media] Nova-S-Plus audio line input
[media] [RFC,1/1] V4L2: Use new CAP bits in existing RDS capable drivers
...
This patch adds audio DMA capture and ALSA mixer elements for the line
input jack of the Hauppauge Nova-S-plus DVB-S PCI card. The Nova-S-plus
has a WM8775 ADC that is currently not detected. This patch enables
this chip and exports volume, balance mute and ALC elements for ALSA
mixer controls.
[mchehab@redhat.com: Fix CodingStyle issues]
Signed-off-by: Lawrence Rust <lawrence@softsystem.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, remove the module names hardcoded in platform data
and pass a NULL module name to those functions.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the sh_vou
platform data uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a driver for the video capture port on VIA integrated chipsets. This
version has a remaining OLPCism or two and expects to be talking to an
ov7670; those can be improved as the need arises.
This work was supported by the One Laptop Per Child project.
Thanks to Laurent Pinchart for a number of useful comments.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new event types for timeout & carrier report
Move timeout handling from ir_raw_event_store_with_filter to
ir-lirc-codec, where it is really needed.
Now lirc bridge ensures proper gap handling.
Extend lirc bridge for carrier & timeout reports
Note: all new ir_raw_event variables now should be initialized
like that: DEFINE_IR_RAW_EVENT(ev);
To clean an existing event, use init_ir_raw_event(&ev);
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch add support of TwinHan 1027 DVB-S card.
Refreshed version of https://patchwork.kernel.org/patch/79753/ patch.
(adapted for the new IR system), still works.
DVB-S support come from a patch originally authored by
Manu Abraham (abraham.manu@gmail.com).
IR Port support were added by Sergey.
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an I2C/v4l2-subdev driver for Siliconfile SR030PC30 VGA
camera sensor with Image Signal Processor. SR030PC30 is
the low resolution camera sensor on Samsung Aquila boards.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a video device driver per each FIMC entity to support
the camera capture input mode. Video capture node is registered
only if CCD sensor data is provided through driver's platfrom data
and board setup code.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch provides a V4L2 SoC Camera driver for OV6650 camera sensor, found
on OMAP1 SoC based Amstrad Delta videophone.
Since I have no experience with camera sensors, and the sensor documentation I
was able to find was not very comprehensive, I left most settings at their
default (reset) values, except for:
- those required for proper mediabus parameters and picture geometry and
format setup,
- those used by controls.
Resulting picture quality may be far from perfect, but better than nothing.
In order to be able to get / set the sensor frame rate from userspace, I
decided to provide two not yet SoC camera supported operations, g_parm and
s_parm. These can be used after applying patch 4/6 from this series,
"SoC Camera: add support for g_parm / s_parm operations".
Created and tested against linux-2.6.36-rc5 on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a V4L2 driver for TI OMAP1 SoC camera interface.
Both videobuf-dma versions are supported, contig and sg, selectable with a
module option. The former uses less processing power, but often fails to
allocate contignuous buffer memory. The latter is free of this problem, but
generates tens of DMA interrupts per frame. If contig memory allocation ever
fails, the driver falls back to sg automatically on next open, but still can
be switched back to contig manually. Both paths work stable for me, even
under heavy load, on my OMAP1510 based Amstrad Delta videophone, that is the
oldest, least powerfull OMAP1 implementation.
The interface generally works in pass-through mode. Since input data byte
endianess can be swapped, it provides up to two v4l2 pixel formats per each of
several soc_mbus formats that have their swapped endian counterparts.
Boards using this driver can provide it with the following platform data:
- if and what freqency clock is expected by an on-board camera sensor,
- what is the maximum pixel clock that should be accepted from the sensor,
- what is the polarity of the sensor provided pixel clock,
- if the interface GPIO line is connected to a sensor reset/powerdown input
and what is the input polarity.
Created and tested against linux-2.6.36-rc5 on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
>From Joris van Rantwijk <jorispubl@xs4all.nl>:
I tested lirc_serial and found that it works fine.
Except the LIRC ioctls do not work in my 64-bit-kernel/32-bit-user
setup. I added compat_ioctl entries in the drivers to fix this.
While doing so, I noticed inconsistencies in the argument type of
the LIRC ioctls. All ioctls are declared in lirc.h as having argument
type __u32, however there are a few places where the driver calls
get_user/put_user with an unsigned long argument.
The patch below changes lirc_dev and lirc_serial to use __u32 for all
ioctl arguments, and adds compat_ioctl entries.
It should probably also be done in the other low-level drivers,
but I don't have hardware to test those.
I've dropped the .compat_ioctl addition from Joris' original patch,
as I swear the non-compat definition should now work for both 32-bit
and 64-bit userspace. Technically, I think we still need/want a
in getting a reply to you).
Reported-by: Joris van Rantwijk <jorispubl@xs4all.nl>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Imported from af9015.h. Initial keytable was from
Jose Alberto Reguero <jareguero@telefonica.net> and
Felipe Morales Moreno <felipe.morales.moreno@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Digittrade DVB-T USB Stick remote controller.
Imported from af9015.h. Initial keytable was from Alain Kalker <miki@dds.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Imported from af9015.h.
Initial keytable was from Marc Schneider <macke@macke.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MSI DIGIVOX mini III remote controller. Uses NEC extended 0x61d6.
This remote seems to be same as rc-kworld-315u.c. Anyhow, add new remote
since rc-kworld-315u.c lacks NEC extended address byte.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
struct file_operations was made const in the drivers, but not in struct
lirc_driver:
drivers/staging/lirc/lirc_it87.c:365: warning: initialization discards qualifiers from pointer target type
drivers/staging/lirc/lirc_parallel.c:571: warning: initialization discards qualifiers from pointer target type
drivers/staging/lirc/lirc_serial.c:1073: warning: initialization discards qualifiers from pointer target type
drivers/staging/lirc/lirc_sir.c:482: warning: initialization discards qualifiers from pointer target type
drivers/staging/lirc/lirc_zilog.c:1284: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function is an internal API and belongs in v4l2-common.h, not
videodev.h. The return pointer and probe argument should be const as well.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multiple user-space application instances can open the same video device, but
it only makes sense for one of them to manage the videobuffer queue and set
video format of the device. Restrict soc-camera respectively.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf_waiton() must unlock and relock ext_lock if it has to wait.
For that to happen it needs the videobuf_queue pointer.
Don't attempt to unlock/relock q->ext_lock unless it was locked in the
first place.
vb->state has to be protected by a spinlock to be safe.
This patch is based on code from Mauro Carvalho Chehab <mchehab@redhat.com>.
[mchehab@redhat.com: add extra argument to a few missing places]
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an ext_lock argument to the videobuf init functions. This allows
drivers to pass the vdev->lock pointer (or any other externally held lock)
to videobuf. For now all drivers just pass NULL.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently videobuf uses the vb_lock mutex to lock its data structures.
But this locking will (optionally) move into the v4l2 core, which means
that in that case vb_lock shouldn't be used since the external lock is already
held.
Prepare for this by adding a pointer to such an external mutex and
don't lock if that pointer is set.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers can optionally set a pointer to a mutex in struct video_device.
The core will use that to lock before calling open, read, write, unlocked_ioctl,
poll, mmap or release.
Updated the documentation as well and ensure that v4l2-event knows about the
lock: it will unlock it before doing a blocking wait on an event and relock it
afterwards.
Ensure that the 'video_is_registered' check is done when the lock is held:
a typical disconnect will take the lock as well before unregistering the
device nodes, so to prevent race conditions the video_is_registered check
should also be done with the lock held.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The imon driver currently reimplements its own version of ir_keyup
(along with key release timer functionality also already present in the
core IR code). A follow-up imon patch will make use of ir_keyup and the
IR stack's key release code.
Trivial extraction from David Härdeman's pending rc-core merge and
device interface abstraction patchset to facilitate merging a patch
based on his imon input dev split patch ahead of the larger churn, which
is slated for post-2.6.37-rc1 (after Dmitry's large keycode patches are
merged in mainline).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only reason for keeping I2C_HW_SAA7134 is to allow setting a
per-device polling interval. Just move this info to the platform
data, allowing drivers to change it per device, where needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The include/media/v4l2-i2c-drv.h header was used to be able to compile drivers
in the v4l-dvb hg repository for legacy kernels (mainly pre-2.6.26) without
creating an #ifdef mess.
The hg repository dropped support for kernels < 2.6.26 so we can remove this
header. All i2c drivers that used it have now been converted to use proper
i2c code. The header was a hack, but it did its job well. So I would call
this an honorable removal. :-)
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the vtx (aka videotext aka teletext) API from the v4l2 core.
This API was scheduled for removal in kernel 2.6.35.
The vtx device nodes have been superseded by vbi device nodes
for many years. No applications exist that use the vtx support.
Of the two i2c drivers that actually support this API the saa5249
has been impossible to use for a year now and no known hardware
that supports this device exists. The saa5246a is theoretically
supported by the old mxb boards, but it never actually worked.
In summary: there is no hardware that can use this API and there
are no applications actually implementing this API.
The vtx support still reserves minors 192-223 and we would really
like to reuse those for upcoming new functionality. In the unlikely
event that new hardware appears that wants to use the functionality
provided by the vtx API, then that functionality should be build
around the sliced VBI API instead.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The existing priv field stores subdev private data owned by the subdev
driver. Host (bridge) drivers might need to store per-subdev
host-specific data, such as a pointer to platform data.
Add a v4l2_subdev host_priv field to store host-specific data, and
rename the existing priv field to dev_priv.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"sd" and "err" are too common names to be used in macros for local variables.
Prefix them with an underscore to avoid name clashing.
[mchehab@redhat.com: whitespace cleanups]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes in-kernel decoding with the stock Streamzap PC Remote
work out of the box. There are quite a few things going on in this
patch, all related to getting this working:
1) I had to enable reporting of a long space at the end of each signal,
or I had weird buffering and keybounce issues.
2) The keymap has been reworked slightly to match actual decoded values,
the first edition was missing the pre-data bits present in the lirc
config file for this remote.
3) There's a whole new decoder included, specifically for the
not-quite-RC5 15-bit protocol variant used by the Streamzap PC
Remote. The decoder, while usable with other recievers (tested with
an mceusb receiver), will only be loaded by the streamzap driver, as
its likely not of use in almost all other situations. This can be
revisited if/when all keytable loading (and disabling of unneeded
protocol decoder engines) is moved to userspace, but for now, I think
this makes the most sense.
Note that I did try to enable handling the streamzap RC5-ish protocol in
the current RC5 decoder, but there's no particularly easy way to tell if
its 14-bit RC5 or 15-bit Streamzap until we see bit 14, and even then,
in testing an attempted decoder merge, only 2/3 of the keys were
properly recognized as being the 15-bit variant and decoded correctly,
the rest were close enough to compliant with 14-bit that they were
decoded as such (but they have overlap with one another, and thus we
can't just shrug and use the 14-bit decoded values).
Also of note in this patch is the removal of the streamzap driver's
internal delay buffer. Per discussion w/Christoph, it shouldn't be
needed by lirc any longer anyway, and it doesn't seem to make any
difference to the in-kernel decoder engine. That being the case, I'm
yanking it all out, as it greatly simplifies the driver code.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These have now all been replaced by enum/try/s/g_mbus_fmt.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes a nasty memory corruption bug when using userptr I/O.
The function videobuf_pages_to_sg() sets up the scatter-gather list for the
DMA transfer to the userspace pages. The first transfer is setup correctly
(the size is set to PAGE_SIZE - offset), but all other transfers have size
PAGE_SIZE. This is wrong for the last transfer which may be less than PAGE_SIZE.
Most, if not all, drivers will program the boards DMA engine correctly, i.e.
even though the size in the last sg element is wrong, they will do their
own size calculations and make sure the right amount is DMA-ed, and so seemingly
prevent memory corruption.
However, behind the scenes the dynamic DMA mapping support (in lib/swiotlb.c)
may create bounce buffers if the memory pages are not in DMA-able memory.
This happens for example on a 64-bit linux with a board that only supports
32-bit DMA.
These bounce buffers DO use the information in the sg list to determine the
size. So while the DMA engine transfers the correct amount of data, when the
data is 'bounced' back too much is copied, causing buffer overwrites.
The fix is simple: calculate and set the correct size for the last sg list
element.
Signed-off-by: Hans Verkuil <hans.verkuil@tandberg.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switch the code to use new style of getkeycode and setkeycode
methods to allow retrieving and setting keycodes not only by
their scancodes but also by index.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since this module is also used by drivers that are not yet converted, the old
and new code have to co-exist.
The source is split into three parts: a common part at the top, which is used
by both old and new code, then the old code followed by the new control
framework implementation. This new code is much more readable (and shorter!)
than the original code.
Once all bridge drivers that use this are converted the old code can be
deleted.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx25840 used a private control CX25840_CID_ENABLE_PVR150_WORKAROUND
to be told whether to enable a workaround for certain pvr150 cards.
This is really config data that it needs to get at load time.
Implemented this in cx25840 and ivtv.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a new framework to handle controls which makes life for driver
developers much easier.
Note that this patch moves some of the control support that used to be in
v4l2-common.c to v4l2-ctrls.c. The tables were copied unchanged. The body
of v4l2_ctrl_query_fill() was copied to a new v4l2_ctrl_fill() function
in v4l2-ctrls.c. This new function doesn't use the v4l2_queryctrl
struct anymore, which makes it more general.
The remainder of v4l2-ctrls.c is all new. Highlights include:
- No need to implement VIDIOC_QUERYCTRL, QUERYMENU, S_CTRL, G_CTRL,
S_EXT_CTRLS, G_EXT_CTRLS or TRY_EXT_CTRLS in either bridge drivers
or subdevs. New wrapper functions are provided that can just be plugged in.
Once everything has been converted these wrapper functions can be removed as well.
- When subdevices are added their controls can be automatically merged
with the bridge driver's controls.
- Most drivers just need to implement s_ctrl to set the controls.
The framework handles the locking and tries to be as 'atomic' as possible.
- Ready for the subdev device nodes: the same mechanism applies to subdevs
and their device nodes as well. Sub-device drivers can make controls
local, preventing them from being merged with bridge drivers.
- Takes care of backwards compatibility handling of VIDIOC_S_CTRL and
VIDIOC_G_CTRL. Handling of V4L2_CID_PRIVATE_BASE is fully transparent.
CTRL_CLASS controls are automatically added.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
LIRC: add new IOCTL that enables learning mode (wide band receiver)
Still missing features: carrier report & timeout reports.
Will need to pack these into ir_raw_event
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some ir input devices have small buffer, and interrupt the host
each time it is full (or half full)
Add a helper that automaticly handles timeouts, and also
automaticly merges samples of same time (space-space)
Such samples might be placed by hardware because size of
sample in the buffer is small (a byte for example).
Also remove constness from ir_dev_props, because it now contains timeout
settings that driver might want to change
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, ir device registration fails if keymap requested by driver is not found.
Fix that by always compiling in the empty keymap, and using it as a failback.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ports lirc_streamzap.c over to ir-core in-place, to be followed by
a patch moving the driver over to drivers/media/IR/streamzap.c and
enabling the proper Kconfig bits.
Presently, the in-kernel keymap doesn't work, as the stock Streamzap
remote uses an RC-5-like, but not-quite-RC-5 protocol, which the
in-kernel RC-5 decoder doesn't cope with. The remote can be used right
now with the lirc bridge driver though, and other remotes (at least an
RC-6(A) MCE remote) work perfectly with the driver.
I'll take a look at making the existing RC-5 decoder cope with this odd
duck, possibly implement another standalone decoder engine, or just
throw up my hands and say "meh, use lirc"... But the driver itself
should be perfectly sound.
Remaining items on the streamzap TODO list:
- add LIRC_SET_REC_TIMEOUT-alike support
- add LIRC_GET_M{AX,IN}_TIMEOUT-alike support
- add LIRC_GET_REC_RESOLUTION-alike support
All of the above should be trivial to add. There are patches pending to
add this support to ir-core from Maxim Levitsky, and I'll take care of
these once his patches get integrated. None of them are currently
essential though.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CX2584x and related cores are multifunction subdevices with a number
of internal blocks that act as interrupt sources. Move the v4L2_subdev
interrupt_service_routine callback from v4l_subdev_ir_ops to
v4l2_subdev_core_ops, as the video and audio blocks of a CX2584x and
related cores can generate interrupts along with the IR block. This
change also makes sense for other subdev's that generate interrupts and
do not have an IR block.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a distinction on IR Tx for the CX2388[578] chips of carrier
sense inversion (space is a carrier burst and mark is no burst) and I/O
pin level inversion (0 is high output level, 1 is low output level).
Allow the caller to set these parameters distinctly as v4l2_subdevice
IR parameters. This permits the IR device to be configured and enabled
without the IR Tx LED being on during idle/space time due to an external
hardware level inversion
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add s_io_pin_config core subdev op for the CX2388[578] AV cores.
This is complete for IR_RX, IR_TX, GPIOs 16,19-23, and IRQ_N.
It likely needs work for the I2S signal direction.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a method to v4l2_sudev_core_ops to allow bridge drivers to
manage what signal pads/functions are routed out to multiplexed IO pins on a
pin by pin basis. The interface also allows specifying initial output settings
for pins and disabling an IO pin altogether.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having one big keytable with 2 protocols inside, break it
into two separate tables, being one for NEC and another for RC-5 variants,
and properly identify what variant should be used at the boards entries.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using CEU with CSI2 on SH-Mobile requires some special configuration of the
former. We also have to switch from calling only one subdev .s_mbus_fmt and
.try_mbus_fmt to calling all subdevices. Take care to increment CSI2 driver
use count to prevent it from unloading, while in use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some SH-Mobile SoCs implement a MIPI CSI-2 controller, that can interface to
several video clients and send data to the CEU or to the Image Signal
Processor. This patch implements a v4l2-subdevice driver for CSI-2 to be used
within the soc-camera framework, implementing the second subdevice in addition
to the actual video clients.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
