Now that the core file is the only one actually using any
of the base addresses, we can delete that header and move
the base address definitions into the one and only core
file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a device tree node for the U300 system controller
and remaps this dynamically instead of using hard-coded
virtual addresses. The board power set-up code is altered
to fetch a reference to the syscon using ampersand <&syscon>
notation. This way of passing a pointer to the syscon will
also be used by the clocks.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This register base file is now only used in the machine
itself so move it down into mach-u300.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Get rid of the <mach/syscon.h> header as a prerequisite for
multiplatform support. Do this by pushing the registers down
to their respective drivers and deleting the unused remainder.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have now transferred all the U300 peripherals to the device
tree, so we just select USE_OF, and delete all static board data,
then require that this platform shall be booted using the device
tree and nothing else.
This gets rid of the MMCI (PL180), PL022, and serial PL011
platform data entries and more.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This registers the U300 FSMC flash controller from the
device tree, and defines the three partitions. Skip the
BBT scan as in the current platform data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This registers the PL022 PrimeCell from the U300 device
tree. We make a new copy of the platform data for the
device tree boot path, as the old platform data is in an
older file which will be going away.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the COH 901 318 DMA controller to the U300
device tree. All devices now converted to device tree
so far will start to find their DMA channels.
Note that the U300 is not yet using the device tree
to obtain DMA channels, but this is a first step.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DMA controller down into the driver and cleans up in
the <mach/*> namespace for the U300 platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJQ/pQaAAoJEEEQszewGV1z80kP/joeZo37gp+TfkjL5X+BZDb5
O05Q+Ic70t7u80WjACX6vl7YzeRoK8Z9aiNYpDbHT40RuRKTiGH8DLOmYsjxqXg0
LpqTm+RoLlgrrrOw4nwdN7nE/2eUF5SuidhCUfueZlkTQJLdPWDO0n/fBHR05CGM
WovRiNtqJSS9X5JrNjQT19oZDpqsY/mvygAV0usiiWC4qxUQFo0ZaT4jis/UeKCF
RD/UsILTRe86Q2UGr+XPp45UihqZ4qH187cZMPWr6FZyeIu24vGo7ew+R4KEjVEz
xE6NGkqnYl4LiW+K2Y0TYyN4TnhaaIi4/iSVZxiLKsTvE+LWxrv+4cIU4AUQsoY+
XllWkX1aS+zWaeFOwc6EPuhZFxdkmlGRsz8oqOh0kqswtIiM9wCRgWGCuFcns//A
N1+OAC5kK9QlrLWoJnnND/SYsl97GhwySqMLL1FgIjTw3CtseqNfv3LjeyNRKIVT
jNX6b6Gc/EOOzZFrAMMvinpaFzgnsWp5xohb7EclKevfArsttrlm80fBnbSnq5lA
FzFH/9fi8ca2Lu9hoakNHnTFtx9d5qBU8gPDCwsRGb1gHfmlCQsqrVxSvTVyKOjN
ZQfeGNfPdddeKvvo/1l1tTuWzMOMY+AIhfWJGrkUvhlykjDsD4M0m4gKnfMnZeUY
zWQv3rJU9L76oGhEtmKZ
=IGqm
-----END PGP SIGNATURE-----
Merge tag 'coh901318-for-arm-soc' of http://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/drivers
This pushes the platform data for the U300 COH901318
DMA controller down into the driver and cleans up in
the <mach/*> namespace for the U300 platform.
* tag 'coh901318-for-arm-soc' of http://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
dma: coh901318: cut down on platform data abstraction
dma: coh901318: merge header files
dma: coh901318: push definitions into driver
dma: coh901318: push header down into the DMA subsystem
dma: coh901318: skip hard-coded addresses
dma: coh901318: remove hardcoded target addresses
dma: coh901318: push platform data into driver
dma: coh901318: create a proper platform data file
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-u300/core.c
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ8ZobAAoJEMhvYp4jgsXiihIH/2VvxmSHZb0e3jN6AR0B42b7
9EwX0IE0B23t91hNTwdzzmTJQYA7pMmWkgHNfd3vIeqSepJAmrVv/gp4iM9CtPwE
KNh+kDWOK2ZsOH4Vb0lYRJHN8WQOIQHuCUr9+MdYLNOgf/pPL6G/Y9kv9A1e7fTC
W+tFRjC5N1ilZMGyowX12L1wnwDk6kHzed6YV6bskC17cZ9/pg8PhSVbM4A/3kAv
NXYKqbXJb+eCsWGXg/knZXOL6V9gBwvVYoe4O9X3nQ0226AWB9caad8l8tchAjRB
fmrYF1tbkpOWPnLxhvQy5b5MJichJgTMJHh7RgiEcc/3f63kOljjlx4QKiqHvT0=
=q7gm
-----END PGP SIGNATURE-----
Merge tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux into next/cleanup
From Rob Herring:
Initial irqchip init infrastructure and GIC and VIC clean-ups
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
* tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux:
irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h
ARM: picoxcell: use common irqchip_init function
ARM: spear: use common irqchip_init function
irqchip: Move ARM VIC to drivers/irqchip
ARM: samsung: remove unused tick.h
ARM: remove unneeded vic.h includes
ARM: remove mach .handle_irq for VIC users
ARM: VIC: set handle_arch_irq in VIC initialization
ARM: VIC: shrink down vic.h
irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h
ARM: use common irqchip_init for GIC init
irqchip: Move ARM GIC to drivers/irqchip
ARM: remove mach .handle_irq for GIC users
ARM: GIC: set handle_arch_irq in GIC initialization
ARM: GIC: remove direct use of gic_raise_softirq
ARM: GIC: remove assembly ifdefs from gic.h
ARM: mach-ux500: use SGI0 to wake up the other core
arm: add set_handle_irq() to register the parent IRQ controller handler function
irqchip: add basic infrastructure
irqchip: add to the directories part of the IRQ subsystem in MAINTAINERS
Fixed up massive merge conflicts with the timer cleanup due to adjacent changes:
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-bcm/board_bcm.c
arch/arm/mach-cns3xxx/cns3420vb.c
arch/arm/mach-ep93xx/adssphere.c
arch/arm/mach-ep93xx/edb93xx.c
arch/arm/mach-ep93xx/gesbc9312.c
arch/arm/mach-ep93xx/micro9.c
arch/arm/mach-ep93xx/simone.c
arch/arm/mach-ep93xx/snappercl15.c
arch/arm/mach-ep93xx/ts72xx.c
arch/arm/mach-ep93xx/vision_ep9307.c
arch/arm/mach-highbank/highbank.c
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-msm/board-dt-8960.c
arch/arm/mach-netx/nxdb500.c
arch/arm/mach-netx/nxdkn.c
arch/arm/mach-netx/nxeb500hmi.c
arch/arm/mach-nomadik/board-nhk8815.c
arch/arm/mach-picoxcell/common.c
arch/arm/mach-realview/realview_eb.c
arch/arm/mach-realview/realview_pb1176.c
arch/arm/mach-realview/realview_pb11mp.c
arch/arm/mach-realview/realview_pba8.c
arch/arm/mach-realview/realview_pbx.c
arch/arm/mach-socfpga/socfpga.c
arch/arm/mach-spear13xx/spear1310.c
arch/arm/mach-spear13xx/spear1340.c
arch/arm/mach-spear13xx/spear13xx.c
arch/arm/mach-spear3xx/spear300.c
arch/arm/mach-spear3xx/spear310.c
arch/arm/mach-spear3xx/spear320.c
arch/arm/mach-spear3xx/spear3xx.c
arch/arm/mach-spear6xx/spear6xx.c
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-u300/core.c
arch/arm/mach-ux500/board-mop500.c
arch/arm/mach-ux500/cpu-db8500.c
arch/arm/mach-versatile/versatile_ab.c
arch/arm/mach-versatile/versatile_dt.c
arch/arm/mach-versatile/versatile_pb.c
arch/arm/mach-vexpress/v2m.c
include/asm-generic/vmlinux.lds.h
Now that we have VIC moved to drivers/irqchip and all VIC DT init for
platforms using irqchip_init, move gic.h and update the remaining
includes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Now that the VIC initialization sets up the handle_arch_irq pointer, we
can remove it for all machines and make it static. Move vic_handle_irq
to avoid a forward declaration.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Hubert Feurstein <hubert.feurstein@contec.at>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The defines in U300's <mach/coh901318.h> are now only used by
the DMA engine driver itself, so move the header down into the
DMA subsystem.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We're only ever going to support the U300 with this driver
so skip the separation of platform data from driver, and push
it down into the driver itself.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This extracts the platform data that we will keep generic
from the U300 platform and associates it with the COH901318
driver in <linux/platform_data/dma-coh901318.h>.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This is a batch of fixes for arm-soc platforms, most of it is for OMAP
but there are others too (i.MX, Tegra, ep93xx). Fixes warnings, some
broken platforms and drivers, etc. A bit all over the map really.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4g/i
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is a batch of fixes for arm-soc platforms, most of it is for OMAP
but there are others too (i.MX, Tegra, ep93xx). Fixes warnings, some
broken platforms and drivers, etc. A bit all over the map really."
There was some concern about commit 68136b10 ("RM: sunxi: Change device
tree naming scheme for sunxi"), but Tony says:
"Looks like that's trivial to fix as needed, no need to rebuild the
branch to fix that AFAIK.
The fix can be done once Olof is available online again.
Linus, I suggest that you go ahead and pull this if there are no other
issues with this branch."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
ARM: sunxi: Change device tree naming scheme for sunxi
ARM: ux500: fix missing include
ARM: u300: delete custom pin hog code
ARM: davinci: fix build break due to missing include
ARM: exynos: Fix warning due to missing 'inline' in stub
ARM: imx: Move platform-mx2-emma to arch/arm/mach-imx/devices
ARM i.MX51 clock: Fix regression since enabling MIPI/HSP clocks
ARM: dts: mx27: Fix the AIPI bus for FEC
ARM: OMAP2+: common: remove use of vram
ARM: OMAP3/4: cpuidle: fix sparse and checkpatch warnings
ARM: OMAP4: clock data: DPLLs are missing bypass clocks in their parent lists
ARM: OMAP4: clock data: div_iva_hs_clk is a power-of-two divider
ARM: OMAP4: Fix EMU clock domain always on
ARM: OMAP4460: Workaround ABE DPLL failing to turn-on
ARM: OMAP4: Enhance support for DPLLs with 4X multiplier
ARM: OMAP4: Add function table for non-M4X dplls
ARM: OMAP4: Update timer clock aliases
ARM: OMAP: Move plat/omap-serial.h to include/linux/platform_data/serial-omap.h
ARM: dts: Add build target for omap4-panda-a4
ARM: dts: OMAP2420: Correct H4 board memory size
...
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlDSAa4ACgkQdwG7hYl686MMcACeNYa//ghPtccb5L+IRXsqaFDL
Yi4AoLWOaOjN8qM4KUF/bfMEkwNGAePz
=DaAQ
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd
Pull MTD updates from David Woodhouse:
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
* tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd: (96 commits)
mtd: nand: typo in nand_id_has_period() comments
mtd: nand/gpio: use io{read,write}*_rep accessors
mtd: block2mtd: throttle writes by calling balance_dirty_pages_ratelimited.
mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems
mtd: nand/docg4: fix and improve read of factory bbt
mtd: nand/docg4: reserve bb marker area in ecclayout
mtd: nand/docg4: add support for writing in reliable mode
mtd: mxc_nand: reorder part_probes to let cmdline override other sources
mtd: mxc_nand: fix unbalanced clk_disable() in error path
mtd: nandsim: Introduce debugfs infrastructure
mtd: physmap_of: error checking to prevent a NULL pointer dereference
mtg: docg3: potential divide by zero in doc_write_oob()
mtd: bcm47xxnflash: writing support
mtd: tests/read: initialize buffer for whole next page
mtd: at91: atmel_nand: return bit flips for the PMECC read_page()
mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.c
mtd: nand: onfi need to be probed in 8 bits mode
mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
mtd: nand: print flash size during detection
mted: nand_wait_ready timeout fix
...
With recent changes in the kernel, the MMCI and PL011 UART
drivers will autonomously request their pins to be muxed in,
so this machine-specific pin hogging code is just interfering
with the proper mechanism and causing regressions in the v3.8
kernel. Delete it and the problems go away.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to be
part of the multiplatform support -- the first "big" SoC that is moved
over (more multiplatform work comes in a separate branch later during
the merge window).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zfPd
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups on various subarchitectures from Olof Johansson:
"Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to
be part of the multiplatform support -- the first "big" SoC that is
moved over (more multiplatform work comes in a separate branch later
during the merge window)."
Conflicts fixed as per Olof, including a silent semantic one in
arch/arm/mach-omap2/board-generic.c (omap_prcm_restart() was renamed to
omap3xxx_restart(), and a new user of the old name was added).
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (189 commits)
ARM: omap: fix typo on timer cleanup
ARM: EXYNOS: Remove unused regs-mem.h file
ARM: EXYNOS: Remove unused non-dt support for dwmci controller
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: SAMSUNG: use devm_ functions for ADC driver
ARM: EXYNOS: no duplicate mask/unmask in eint0_15
ARM: S3C24XX: SPI clock channel setup is fixed for S3C2443
ARM: EXYNOS: Remove i2c0 resource information and setting of device names
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
...
Let's stop spawning the pinctrl driver from the GPIO driver,
we have these two mechanisms broken apart now, and they can
each probe in isolation. If the GPIO driver cannot find its
pin controller (pinctrl-u300), the pin controller core will
tell it to defer probing.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Do not use the platform_data to pass resource and be smart in the drivers.
Just pass it via resource
Switch to devm_request_and_ioremap at the sametime
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-By: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This switches the COH 901 pinctrl driver to allocate its GPIO
IRQs dynamically, and start to use a linear irqdomain to map
from the hardware IRQs.
This way we can cut away the complex allocation of IRQ numbers
from the <mach/irqs.h> file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The U300 IRQs were bumped once to offset to 1 (in order to avoid
using IRQ 0 which is now NO_IRQ). This was OK as we were still
passing the number of irqs in the .nr_irqs field of the machine,
with descriptors allocated at boot time.
However .nr_irqs should be 0, leading the system to reserve the
first 16 IRQs. Then the VIC driver will complain that IRQs 1
thru 15 are pre-allocated, so to avoid this and use free
descriptors, move all IRQs up to offset 32.
This will all be done away with as we migrate to device tree,
so it is an interim solution.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No framework work here, only a bunch of driver updates of varying sizes:
- Factoring out of the core hardware support from the MXS MMC driver by
Marek Vasut to allow the hardware to also be used for SPI.
- Lots of error handling cleanups from Guenter Roeck
- Removal of the existing Tegra driver which is quite comprehensively
broken as detailed in the changelog for the removal.
- DT suppport for the PL022 and GPIO drivers.
- pinctrl support for OMAP and PL022.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ld23
-----END PGP SIGNATURE-----
Merge tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi updates from Mark Brown:
"No framework work here, only a bunch of driver updates of varying
sizes:
- Factoring out of the core hardware support from the MXS MMC driver
by Marek Vasut to allow the hardware to also be used for SPI.
- Lots of error handling cleanups from Guenter Roeck
- Removal of the existing Tegra driver which is quite comprehensively
broken as detailed in the changelog for the removal.
- DT suppport for the PL022 and GPIO drivers.
- pinctrl support for OMAP and PL022."
Pulling from Mark Brown as Grant Likely is still busy moving.
* tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc: (53 commits)
spi: remove completely broken Tegra driver
spi/imx: set the inactive state of the clock according to the clock polarity
spi/pl022: get/put resources on suspend/resume
spi/pl022: use more managed resources
spi/pl022: Devicetree support w/o platform data
spi/s3c64xx: Don't free controller_data on non-dt platforms
spi: omap2-mcspi: add pinctrl support
spi/pl022: adopt pinctrl support
spi: omap2-mcspi: Cleanup the omap2_mcspi_txrx_dma function
spi/gpio: Fix stub for spi_gpio_probe_dt()
spi/mxs: Make the SPI block clock speed configurable via DT
spi: spi-sh-hspi: drop frees of devm_ alloc'd data
spi/pl022: Fix chipselects pointer computation
spi: spi-tle62x0: Use module_spi_driver macro
mxs/spi: Rework the mxs_ssp_timeout to be more readable
mxs/spi: Decrement the DMA/PIO border
mxs/spi: Increment the transfer length only if transfer succeeded
mxs/spi: Fix issues when doing long continuous transfer
spi: spi-gpio: Add DT bindings
spi: spi-gpio: store chipselect information in private structure
...
Amend the PL022 pin controller to optionally take a pin control
handle and set the state of the pins to "default" on boot and
runtime resume, and to "sleep" at runtime suspend. This way we
will dynamically save power on the SPI busses, for example some
electronic designs may be able to ground the pins when unused
instead of pull-up. Some pin controllers may want to set the
pins as wake-up sources when sleeping.
Effect on platforms using the PL022 driver:
- If the platform does not use pin control - no semantic effect,
the pinctrl stubs will kick in and resolve the situation.
- Platforms using this driver and have pin control but no
function defined for the PL022 need to either supply a
"default" function in their map or enable pinctrl dummies
so the driver is satisfied.
- Platforms using this driver with hogs for setting up the PL022
pin control - stop using hogs to take the pl022 pin control
handle, let the driver handle this.
I'be looked at some platforms that may be affected:
- SPEAr: appears to define the proper functions in their device
trees and not hogging them, so things should be smooth, the
driver will simply start to take its pins.
- Ux500: the proper function is defined and will be taken properly
by the driver. New sleep states introduced by a separate patch to
ux500 but no regression, since the default state is sufficient.
- U300: old hog deleted as part of this patch.
- LPC32xx: does not appear to be using pinctrl.
- ARM Integrator IMPD1, RealView & Versatile: does not use pinctrl.
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This converts the U300 to use sparse IRQs, which is simple now
that the number of machines are reduced.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We were broadcasting <mach/dma_channels.h> to the entire kernel
for no reason at all, push this down into the machine folder
where it belongs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This gets rid of the separate u300.c file in mach-u300 since
it can just as well live right in core.c, then we also get
rid of the broadcasted <mach/platform.h> file that is not
helping anyone. Put the interface to the system timer into
a separate header.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the platform-specific COH901 pin control header out of the
ARM tree and down into the proper platform data include
directory.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As the non-U335 U300 variants are retired from the ARM tree,
also delete the pinctrl driver codepaths for these variants.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This retires the B26/S26, B330/S330 and B365/S365 boards from
the U300 platform. The only board really used anywhere today
is the S335 so let's concentrate any efforts on that one board.
Also the board variants are selected at compile-time, which is
strictly a no-no these days, if multi-board support is to be
brought back it need to happen using run-time and device tree.
My work on ARM Linux started on the B26/S26 so it's a bit sad
to see it go, but there is a time to move on with all things
in life.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the U300 clock implementation over to use the common
struct clk and moves the implementation down into drivers/clk.
Since VCO isn't used in tree it was removed, it's not hard to
put it back in if need be.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[mturquette@linaro.org: trivial Makefile conflict]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Since the VIC was converted to use generic IRQ domains IRQ 0
is silently ignored. This IRQ is used on the U300 so we're
missing it now. Bump all IRQ numbers by one since they are
now decoupled from the hardware IRQ numbers.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Artem's cleanup of the MTD API continues apace.
Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst others.
More work on DiskOnChip G3, new driver for DiskOnChip G4.
Clean up debug/warning printks in JFFS2 to use pr_<level>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk92K6UACgkQdwG7hYl686NrMACfWQJRWasR78MWKfkT2vWZwTFJ
X5AAoKiSYO2pfo5gWJGOAahNC1zUqMX0
=i3Vb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6
Pull MTD changes from David Woodhouse:
- Artem's cleanup of the MTD API continues apace.
- Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst
others.
- More work on DiskOnChip G3, new driver for DiskOnChip G4.
- Clean up debug/warning printks in JFFS2 to use pr_<level>.
Fix up various trivial conflicts, largely due to changes in calling
conventions for things like dmaengine_prep_slave_sg() (new inline
wrapper to hide new parameter, clashing with rewrite of previously last
parameter that used to be an 'append' flag, and is now a bitmap of
'unsigned long flags').
(Also some header file fallout - like so many merges this merge window -
and silly conflicts with sparse fixes)
* tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits)
mtd: docg3 add protection against concurrency
mtd: docg3 refactor cascade floors structure
mtd: docg3 increase write/erase timeout
mtd: docg3 fix inbound calculations
mtd: nand: gpmi: fix function annotations
mtd: phram: fix section mismatch for phram_setup
mtd: unify initialization of erase_info->fail_addr
mtd: support ONFI multi lun NAND
mtd: sm_ftl: fix typo in major number.
mtd: add device-tree support to spear_smi
mtd: spear_smi: Remove default partition information from driver
mtd: Add device-tree support to fsmc_nand
mtd: fix section mismatch for doc_probe_device
mtd: nand/fsmc: Remove sparse warnings and errors
mtd: nand/fsmc: Add DMA support
mtd: nand/fsmc: Access the NAND device word by word whenever possible
mtd: nand/fsmc: Use dev_err to report error scenario
mtd: nand/fsmc: Use devm routines
mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform
mtd: fsmc_nand: add pm callbacks to support hibernation
...
Address Latch Enable (ALE) and Command Latch Enable (CLE) defines are
platform specific and were wrongly put in driver specific fsmc.h file.
Move such defines to their respective platform.
Also instead of relying on fsmc driver, pass ALE, CLE offsets explicitly
from individual platform.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Pull #2 ARM updates from Russell King:
"Further ARM AMBA primecell updates which aren't included directly in
the previous commit. I wanted to keep these separate as they're
touching stuff outside arch/arm/."
* 'amba' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7362/1: AMBA: Add module_amba_driver() helper macro for amba_driver
ARM: 7335/1: mach-u300: do away with MMC config files
ARM: 7280/1: mmc: mmci: Cache MMCICLOCK and MMCIPOWER register
ARM: 7309/1: realview: fix unconnected interrupts on EB11MP
ARM: 7230/1: mmc: mmci: Fix PIO read for small SDIO packets
ARM: 7227/1: mmc: mmci: Prepare for SDIO before setting up DMA job
ARM: 7223/1: mmc: mmci: Fixup use of runtime PM and use autosuspend
ARM: 7221/1: mmc: mmci: Change from using legacy suspend
ARM: 7219/1: mmc: mmci: Change vdd_handler to a generic ios_handler
ARM: 7218/1: mmc: mmci: Provide option to configure bus signal direction
ARM: 7217/1: mmc: mmci: Put power register deviations in variant data
ARM: 7216/1: mmc: mmci: Do not release spinlock in request_end
ARM: 7215/1: mmc: mmci: Increase max_segs from 16 to 128
Pull #1 ARM updates from Russell King:
"This one covers stuff which Arnd is waiting for me to push, as this is
shared between both our trees and probably other trees elsewhere.
Essentially, this contains:
- AMBA primecell device initializer updates - mostly shrinking the
size of the device declarations in platform code to something more
reasonable.
- Getting rid of the NO_IRQ crap from AMBA primecell stuff.
- Nicolas' idle cleanups. This in combination with the restart
cleanups from the last merge window results in a great many
mach/system.h files being deleted."
Yay: ~80 files, ~2000 lines deleted.
* 'for-armsoc' of git://git.linaro.org/people/rmk/linux-arm: (60 commits)
ARM: remove disable_fiq and arch_ret_to_user macros
ARM: make entry-macro.S depend on !MULTI_IRQ_HANDLER
ARM: rpc: make default fiq handler run-time installed
ARM: make arch_ret_to_user macro optional
ARM: amba: samsung: use common amba device initializers
ARM: amba: spear: use common amba device initializers
ARM: amba: nomadik: use common amba device initializers
ARM: amba: u300: use common amba device initializers
ARM: amba: lpc32xx: use common amba device initializers
ARM: amba: netx: use common amba device initializers
ARM: amba: bcmring: use common amba device initializers
ARM: amba: ep93xx: use common amba device initializers
ARM: amba: omap2: use common amba device initializers
ARM: amba: integrator: use common amba device initializers
ARM: amba: realview: get rid of private platform amba_device initializer
ARM: amba: versatile: get rid of private platform amba_device initializer
ARM: amba: vexpress: get rid of private platform amba_device initializer
ARM: amba: provide common initializers for static amba devices
ARM: amba: make use of -1 IRQs warn
ARM: amba: u300: get rid of NO_IRQ initializers
...
To show how the pin configuration is used on the U300, let's
include some configs for two GPIO pins.
ChangeLog v1->v2:
- Provide a better example, set the clock return pin to pull-up
and set the card detect pin to high impedance.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl mapping table can now contain entries to:
* Set the mux function of a pin group
* Apply a set of pin config options to a pin or a group
This allows pinctrl_select_state() to apply pin configs settings as well
as mux settings.
v3: Fix find_pinctrl() to iterate over the correct list.
s/_MUX_CONFIGS_/_CONFIGS_/ in mapping table macros.
Fix documentation to use correct mapping table macro.
v2: Added numerous extra PIN_MAP_*() special-case macros.
Fixed kerneldoc typo. Delete pinctrl_get_pin_id() and
replace it with pin_get_from_name(). Various minor fixes.
Updates due to rebase.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The API model is changed from:
p = pinctrl_get(dev, "state1");
pinctrl_enable(p);
...
pinctrl_disable(p);
pinctrl_put(p);
p = pinctrl_get(dev, "state2");
pinctrl_enable(p);
...
pinctrl_disable(p);
pinctrl_put(p);
to this:
p = pinctrl_get(dev);
s1 = pinctrl_lookup_state(p, "state1");
s2 = pinctrl_lookup_state(p, "state2");
pinctrl_select_state(p, s1);
...
pinctrl_select_state(p, s2);
...
pinctrl_put(p);
This allows devices to directly transition between states without
disabling the pin controller programming and put()/get()ing the
configuration data each time. This model will also better suit pinconf
programming, which doesn't have a concept of "disable".
The special-case hogging feature of pin controllers is re-written to use
the regular APIs instead of special-case code. Hence, the pinmux-hogs
debugfs file is removed; see the top-level pinctrl-handles files for
equivalent data.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_register_mappings() already requires that every mapping table
entry have a non-NULL name field.
Logically, this makes sense too; drivers should always request a specific
named state so they know what they're getting. Relying on getting the
first mentioned state in the mapping table is error-prone, and a nasty
special case to implement, given that a given the mapping table may define
multiple states for a device.
Remove a small part of the documentation that talked about optionally
requesting a specific state; it's mandatory now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This provides a single centralized name for the default state.
Update PIN_MAP_* macros to use this state name, instead of requiring the
user to pass a state name in.
With this change, hog entries in the mapping table are defined as those
with state name PINCTRL_STATE_DEFAULT, i.e. all entries have the same
name. This interacts badly with the nested iteration over mapping table
entries in pinctrl_hog_maps() and pinctrl_hog_map() which would now
attempt to claim each hog mapping table entry multiple times. Replacing
the custom hog code with a simple pinctrl_get()/pinctrl_enable().
Update documentation and mapping tables to use this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All the special stuff (like registering input device and so on)
for the U300 MMC is now done away with. We don't need these
special MMC setup kludges, merge this into core.c and be done
with it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This solves the riddle on how the U300 pin controller shall be
able to reference the struct gpio_chip even though these are
two separate drivers: spawn the pinctrl child from the GPIO
driver and pass in the struct gpio_chip as platform data.
In the process we rename the U300 "pinmux-u300" to
"pinctrl-u300" so as not to confuse.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
