The check for reaching max_channels is short circuited by 'continuing'
after successfully adding a channel.
[ Impact: make the 'max_channels' module parameter actually have an effect ]
Cc: <stable@kernel.org>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
'zero_sum' does not properly describe the operation of generating parity
and checking that it validates against an existing buffer. Change the
name of the operation to 'val' (for 'validate'). This is in
anticipation of the p+q case where it is a requirement to identify the
target parity buffers separately from the source buffers, because the
target parity buffers will not have corresponding pq coefficients.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dma: Add SoF and EoF debugging to ipu_idmac.c, minor cleanup
dw_dmac: add cyclic API to DW DMA driver
dmaengine: Add privatecnt to revert DMA_PRIVATE property
dmatest: add dma interrupts and callbacks
dmatest: add xor test
dmaengine: allow dma support for async_tx to be toggled
async_tx: provide __async_inline for HAS_DMA=n archs
dmaengine: kill some unused headers
dmaengine: initialize tx_list in dma_async_tx_descriptor_init
dma: i.MX31 IPU DMA robustness improvements
dma: improve section assignment in i.MX31 IPU DMA driver
dma: ipu_idmac driver cosmetic clean-up
dmaengine: fail device registration if channel registration fails
Add Start-of-Frame and End-of-Frame debugging to ipu_idmac.c, in the
future it might also be needed for the actual video processing in
mx3-camera, at which point, the ISRs will have to be transferred to
mx3_camera.c, for which ipu_irq_map() and ipu_irq_unmap() functions will
have to be exported.
Also simplify a couple of pointer-dereferences.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds a cyclic DMA interface to the DW DMA driver. This is
very useful if you want to use the DMA controller in combination with a
sound device which uses cyclic buffers.
Using a DMA channel for cyclic DMA will disable the possibility to use
it as a normal DMA engine until the user calls the cyclic free function
on the DMA channel. Also a cyclic DMA list can not be prepared if the
channel is already active.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently dma_request_channel() set DMA_PRIVATE capability but never
clear it. So if a public channel was once grabbed by
dma_request_channel(), the device stay PRIVATE forever. Add
privatecnt member to dma_device to correctly revert it.
[lg@denx.de: fix bad usage of 'chan' in dma_async_device_register]
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use the callback infrastructure to report driver/hardware hangs or
missed interrupts. Since this makes the test threads much more
aggressive (from: explicit 1ms sleep to: wait_for_completion) we set the
nice value to 10 so as to not swamp legitimate tasks.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Centralize this common initialization (and one case where ipu_idmac is
duplicating ->chan initialization).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add DMA error handling to the ISR, move common code fragments to functions, fix
scatter-gather element queuing in the ISR, survive channel freeing and
re-allocation in a quick succession.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The i.MX31 IPU DMA driver is a platform driver, but doesn't need hotplug, so we
can use __init and __exit function attributes.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Atsushi points out:
"If alloc_percpu or kzalloc failed, chan_id does not match with its
position in device->channels list.
And above "continue" looks buggy anyway. Keeping incomplete channels
in device->channels list looks very dangerous..."
Also, fix up leakage of idr_ref in the idr_pre_get() and channel init
fail cases.
Reported-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds clkdev support for i.MX31. This is done in a
similar way done previously for i.MX27
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmatest: fix use after free in dmatest_exit
ipu_idmac: fix spinlock type
iop-adma, mv_xor: fix mem leak on self-test setup failure
fsldma: fix off by one in dma_halt
I/OAT: fail self-test if callback test reaches timeout
I/OAT: update driver version and copyright dates
I/OAT: list usage cleanup
I/OAT: set tcp_dma_copybreak to 256k for I/OAT ver.3
I/OAT: cancel watchdog before dma remove
I/OAT: fail initialization on zero channels detection
I/OAT: do not set DCACTRL_CMPL_WRITE_ENABLE for I/OAT ver.3
I/OAT: add verification for proper APICID_TAG_MAP setting by BIOS
dmaengine: update kerneldoc
dmatest_cleanup_chanel will free dtc, so grab ->chan before it goes away
and use it to do the release.
Reported-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
fix a probably accidently dropped reference operator while calling
spin_unlock_restore to an ipu lock.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Cc: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
iop_adma_zero_sum_self_test has the brackets in the wrong place for the
setup failure deallocation path. This error was duplicated in
mv_xor_xor_self_test.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Prevent dev_err from firing even if we successfully detected 'dma-idle'
before the full 1ms timeout has elapsed.
Acked-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If we miss interrupts in the self test then fail registration of this
channel as it is unsuitable for use as a public channel.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Together with new fixes update driver version
and extend copyright dates ranges.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Trivial cleanup, list_del(); list_add_tail() is equivalent
to list_move_tail(). Semantic patch for coccinelle can be
found at www.cccmz.de/~snakebyte/list_move_tail.spatch
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Upcoming server platforms from Intel based on the Nehalem performance
have significantly improved CPU based copy performance.
However, the DMA engine can still be effective at higher I/O sizes
for TCP traffic and at this time copybreak
should be set to 256k for TCP traffic only.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Channel watchdog should be canceled before the rest of dma remove stuff.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
On some systems with I/OAT ver.2 when DCA is disabled in BIOS
situations have been observed
that zero DMA channels are detected instead of four.
To avoid kernel panic driver should fail gracefully with appropriate message.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Flag DCACTRL_CMPL_WRITE_ENABLE is valid only for I/OAT ver.2
so it should not be set for I/OAT ver.3.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
BIOS versions for systems with I/OAT ver.2 have been found
which fail to program APICID_TAG_MAP for DCA.
The ioatdma driver should recognize incorrectly set APICID_TAG_MAP
and disable DCA in that case.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
`iop_adma_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv_xor_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_unmap_regs' referenced in section `.devinit.text' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`orion_nand_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`pxafb_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The conversion of atmel-mci to dma_request_channel missed the
initialization of the channel dma_slave information. The filter_fn passed
to dma_request_channel is responsible for initializing the channel's
private data. This implementation has the additional benefit of enabling
a generic client-channel data passing mechanism.
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i.MX3x SoCs contain an Image Processing Unit, consisting of a Control
Module (CM), Display Interface (DI), Synchronous Display Controller (SDC),
Asynchronous Display Controller (ADC), Image Converter (IC), Post-Filter
(PF), Camera Sensor Interface (CSI), and an Image DMA Controller (IDMAC).
CM contains, among other blocks, an Interrupt Generator (IG) and a Clock
and Reset Control Unit (CRCU). This driver serves IDMAC and IG. They are
supported over dmaengine and irq-chip APIs respectively.
IDMAC is a specialised DMA controller, its DMA channels cannot be used for
general-purpose operations, even though it might be possible to configure
a memory-to-memory channel for memcpy operation. This driver will not work
with generic dmaengine clients, clients, wishing to use it must use
respective wrapper structures, they also must specify which channels they
require, as channels are hard-wired to specific IPU functions.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
dma_find_channel and dma_issue_pending_all are good places to warn about
improper api usage. However, warning correctly means synchronizing with
dma_list_mutex, i.e. too much overhead for these fast-path calls.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The mpc83xx variant uses a shared IRQ for all channels, so the individual
channel nodes don't have an interrupt property. Fix the code to print the
controller IRQ instead if there isn't any for the channel.
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There's no per-channel IRQ on mpc83xx, so only call free_irq if we have one.
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The dmatest driver should use DMA_BIDIRECTIONAL on the destination buffer
to ensure that the poison values are written to RAM and not just written
to cache and discarded.
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The dmaengine sysfs implementation was fixed to support proper
lifetime rules which means that the current:
new_fsl_chan->dev = &new_fsl_chan->common.dev->device;
...retrieves a NULL pointer because new_fsl_chan->common.dev has not
been allocated at this point. So, set new_fsl_chan->dev to a valid
device.
Cc: Li Yang <leoli@freescale.com>
Cc: Zhang Wei <zw@zh-kernel.org>
Reported-by: Ira Snyder <iws@ovro.caltech.edu>
Tested-by: Ira Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In dmaengine we track the dependencies between the descriptors
using the 'next' pointers of the structure. These pointers are
set to NULL as soon as the corresponding descriptor has been
submitted to the channel (in dma_run_dependencies()).
But, the first 'next' in chain is still remaining set, regardless
the fact, that tx->next has been already submitted. This may lead to
multiple submissions of the same descriptor. This patch fixes this.
Actually, some previous implementation of the xxx_run_dependencies()
function already had this fix in place. The fdb..0eaf3 commit, beside the
correct things, broke this.
Cc: <stable@kernel.org>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the multiple device case we need to re-arm the completion and protect
against concurrent self-tests. The printk from the test callback is
removed as it can arbitrarily delay completion of the test.
Cc: <stable@kernel.org>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There are dmaengine users that would like to register dma devices at
subsys_initcall time to ensure channels are available by device_initcall
time.
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Allow dma_filter_fn routines to disambiguate multiple channels on a device
rather than assuming that all channels on a device are equal.
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This brings some predictability to dma device numbers, i.e. an rmmod/insmod
cycle may now result in /sys/class/dma/dma0chan0 being restored rather than
/sys/class/dma/dma1chan0 appearing.
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Resolves:
WARNING: at drivers/base/core.c:122 device_release+0x4d/0x52()
Device 'dma0chan0' does not have a release() function, it is broken and must be fixed.
The dma_chan_dev object is introduced to gear-match sysfs kobject and
dmaengine channel lifetimes. When a channel is removed access to the
sysfs entries return -ENODEV until the kobject can be released.
The bulk of the change is updates to existing code to handle the extra
layer of indirection between a dma_chan and its struct device.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Unregistering services should only happen at "remove" time. This prevents
the device from being unregistered while dmaengine clients are still
active. Also, the comment on ioat_remove is stale since removal is prevented
while a channel may be in use.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This BUG_ON caught problems in early development but now it is in the
way as it invalidly triggers when trying to remove the module.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
DMA_NAK is now useless. We can just use a bool instead.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reference counting is done at the module level so clients need not worry
that a channel will leave while they are actively using dmaengine.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
All users have been converted to either the general-purpose allocator,
dma_find_channel, or dma_request_channel.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that clients no longer need to be notified of channel arrival
dma_async_client_register can simply increment the dmaengine_ref_count.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
dma_request_channel provides an exclusive channel, so we no longer need to
pass slave data through dmaengine.
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Replace the client registration infrastructure with a custom loop to
poll for channels. Once dma_request_channel returns NULL stop asking
for channels. A userspace side effect of this change if that loading
the dmatest module before loading a dma driver will result in no
channels being found, previously dmatest would get a callback. To
facilitate testing in the built-in case dmatest_init is marked as a
late_initcall. Another side effect is that channels under test can not
be used for any other purpose.
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This interface is primarily for device-to-memory clients which need to
search for dma channels with platform-specific characteristics. The
prototype is:
struct dma_chan *dma_request_channel(dma_cap_mask_t mask,
dma_filter_fn filter_fn,
void *filter_param);
When the optional 'filter_fn' parameter is set to NULL
dma_request_channel simply returns the first channel that satisfies the
capability mask. Otherwise, when the mask parameter is insufficient for
specifying the necessary channel, the filter_fn routine can be used to
disposition the available channels in the system. The filter_fn routine
is called once for each free channel in the system. Upon seeing a
suitable channel filter_fn returns DMA_ACK which flags that channel to
be the return value from dma_request_channel. A channel allocated via
this interface is exclusive to the caller, until dma_release_channel()
is called.
To ensure that all channels are not consumed by the general-purpose
allocator the DMA_PRIVATE capability is provided to exclude a dma_device
from general-purpose (memory-to-memory) consideration.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
async_tx and net_dma each have open-coded versions of issue_pending_all,
so provide a common routine in dmaengine.
The implementation needs to walk the global device list, so implement
rcu to allow dma_issue_pending_all to run lockless. Clients protect
themselves from channel removal events by holding a dmaengine reference.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Allowing multiple clients to each define their own channel allocation
scheme quickly leads to a pathological situation. For memory-to-memory
offload all clients can share a central allocator.
This simply moves the existing async_tx allocator to dmaengine with
minimal fixups:
* async_tx.c:get_chan_ref_by_cap --> dmaengine.c:nth_chan
* async_tx.c:async_tx_rebalance --> dmaengine.c:dma_channel_rebalance
* split out common code from async_tx.c:__async_tx_find_channel -->
dma_find_channel
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Simply, if a client wants any dmaengine channel then prevent all dmaengine
modules from being removed. Once the clients are done re-enable module
removal.
Why?, beyond reducing complication:
1/ Tracking reference counts per-transaction in an efficient manner, as
is currently done, requires a complicated scheme to avoid cache-line
bouncing effects.
2/ Per-transaction ref-counting gives the false impression that a
dma-driver can be gracefully removed ahead of its user (net, md, or
dma-slave)
3/ None of the in-tree dma-drivers talk to hot pluggable hardware, but
if such an engine were built one day we still would not need to notify
clients of remove events. The driver can simply return NULL to a
->prep() request, something that is much easier for a client to handle.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
async_tx.ko is a consumer of dma channels. A circular dependency arises
if modules in drivers/dma rely on common code in async_tx.ko. It
prevents either module from being unloaded.
Move dma_wait_for_async_tx and async_tx_run_dependencies to dmaeninge.o
where they should have been from the beginning.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Mapping the destination multiple times is a misuse of the dma-api.
Since the destination may be reused as a source, ensure that it is only
mapped once and that it is mapped bidirectionally. This appears to add
ugliness on the unmap side in that it always reads back the destination
address from the descriptor, but gcc can determine that dma_unmap is a
nop and not emit the code that calculates its arguments.
Cc: <stable@kernel.org>
Cc: Saeed Bishara <saeed@marvell.com>
Acked-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is a possibility to have two devices registered with the same id.
Cc: <stable@kernel.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As part of the ioat_dma self-test it performs a printk from a completion
callback. Depending on the system console configuration this output can
take longer than a millisecond causing the self-test to fail. Introduce a
completion with a generous timeout to mitigate this failure.
Cc: <stable@kernel.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that the critical read back to flush the next descriptor address is
fixed we can downgrade some BUG_ONs that need only be enabled when testing
changes to the driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The current dummy read references the wrong address allowing the next
descriptor address update to linger in the store buffer and get passed
by an 'append' event.
This issue was uncovered by the change from strongly-ordered to device
memory for the adma registers.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
async_tx.callback should be checked for the first
not the last descriptor in the chain.
Cc: <stable@kernel.org>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error handling needs to be modified in dma_pin_iovec_pages().
It should return NULL instead of ERR_PTR
(pinned_list is checked for NULL in tcp_recvmsg() to determine
if iovec pages have been successfully pinned down).
In case of error for the first iovec,
local_list->nr_iovecs needs to be initialized.
Cc: <stable@kernel.org>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ioatdma driver is loaded but not used it does not allocate descriptors.
Before it frees channel resources it should first be sure
that they have been previously allocated.
Cc: <stable@kernel.org>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Tested-by: Tom Picard <tom.s.picard@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I7300_idle driver is not configured, there is a compile time
warning about IDLE_IOAT_CHANNEL not defined. Fix it.
Reported-by: Suresh Siddha <suresh.b.siddha@intel.com>
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Based on input from Andi Kleen:
share the platform detection code with ioat_dma and disable the channel in
dma engine only for specific platforms.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The Intel 7300 Memory Controller supports dynamic throttling of memory which can
be used to save power when system is idle. This driver does the memory
throttling when all CPUs are idle on such a system.
Refer to "Intel 7300 Memory Controller Hub (MCH)" datasheet
for the config space description.
Signed-off-by: Andy Henroid <andrew.d.henroid@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
fsldma: allow Freescale Elo DMA driver to be compiled as a module
fsldma: remove internal self-test from Freescale Elo DMA driver
drivers/dma/dmatest.c: switch a GFP_ATOMIC to GFP_KERNEL
dmatest: properly handle duplicate DMA channels
drivers/dma/ioat_dma.c: drop code after return
async_tx: make async_tx_run_dependencies() easier to read
The tasklet checks RAW.BLOCK twice, and does not check RAW.XFER. This is
obviously wrong, and could theoretically cause the driver to hang.
Reported-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify the Freescale Elo / Elo Plus DMA driver so that it can be compiled as
a module.
The primary change is to stop treating the DMA controller as a bus, and the
DMA channels as devices on the bus. This is because the Open Firmware (OF)
kernel code does not allow busses to be removed, so although we can call
of_platform_bus_probe() to probe the DMA channels, there is no
of_platform_bus_remove(). Instead, the DMA channels are manually probed,
similar to what fsl_elbc_nand.c does.
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The Freescale Elo DMA driver runs an internal self-test before registering
the channels with the DMA engine. This self-test has a fundemental flaw in
that it calls the DMA engine's callback functions directly before the
registration. However, the registration initializes some variables that the
callback functions uses, namely the device struct.
The code works today because there are two device structs: the one created
by the DMA engine, and one created by the Open Firmware (OF) subsystem. The
self-test currently uses the device struct created by OF. However, in the
future, some of the device structs created by OF will be eliminated.
This means that the self-test will only have access to the device struct
created by the DMA engine. But this device struct isn't initialized when
the self-test runs, and this causes a kernel panic.
Since there is already a DMA test module (dmatest), the internal self-test
code is not useful anyway. It is extremely unlikely that the test will fail
in normal usage. It may have been helpful during development, but not any more.
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
It was needlessly using the unreliable GFP_ATOMIC.
Cc: Timur Tabi <timur@freescale.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Update the the dmatest driver so that it handles duplicate DMA channels
properly.
When a DMA client is notified of an available DMA channel, it must check if it
has already allocated resources for that channel. If so, it should return
DMA_DUP. This can happen, for example, if a DMA driver calls
dma_async_device_register() more than once.
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The break after the return serves no purpose.
Signed-off-by: Julia Lawall <julia@diku.dk>
Reviewed-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch performs the equivalent include directory shuffle for
plat-orion, and fixes up all users.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
* 'for-linus-merged' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5177/1: arm/mach-sa1100/Makefile: remove CONFIG_SA1100_USB
[ARM] 5166/1: magician: add MAINTAINERS entry
[ARM] fix pnx4008 build errors
[ARM] Fix SMP booting with non-zero PHYS_OFFSET
[ARM] 5185/1: Fix spi num_chipselect for lubbock
[ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
[ARM] Add support for arch/arm/mach-*/include and arch/arm/plat-*/include
[ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead
[ARM] Eliminate useless includes of asm/mach-types.h
[ARM] Fix circular include dependency with IRQ headers
avr32: Use <mach/foo.h> instead of <asm/arch/foo.h>
avr32: Introduce arch/avr32/mach-*/include/mach
avr32: Move include/asm-avr32 to arch/avr32/include/asm
[ARM] sa1100_wdt: use reset_status to remember watchdog reset status
[ARM] pxa: introduce reset_status and clear_reset_status for driver's usage
[ARM] pxa: introduce reset.h for reset specific header information
If you are using linked lists for queues list_splice() will not do what
you would expect even if you use the elements passed reversed. We need
to handle these differently. We add list_splice_tail() and
list_splice_tail_init().
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds to ioatdma and dca modules
support for Intel I/OAT DMA engine ver.3 (aka CB3 device).
The main features of I/OAT ver.3 are:
* 8 single channel DMA devices (8 channels total)
* 8 DCA providers, each can accept 2 requesters
* 8-bit TAG values and 32-bit extended APIC IDs
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
I/OAT DMA performance tuning showed different optimal values of
tcp_dma_copybreak for different I/OAT versions (4096 for 1.2 and 2048
for 2.0). This patch lets ioatdma driver set tcp_dma_copybreak value
according to these results.
[dan.j.williams@intel.com: remove some ifdefs]
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Due to occasional DMA channel hangs observed for I/OAT versions 1.2 and 2.0
a watchdog has been introduced to check every 2 seconds
if all channels progress normally.
If stuck channel is detected, driver resets it.
The reset is done in two parts. The second part is scheduled
by the first one to reinitialize the channel after the restart.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Force callers that trigger an "out of descriptors" condition to run the
cleanup loop directly. Alleviates the requirement to have soft-irqs
enabled when polling for a descriptor in async_xor.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This adds a driver for the Synopsys DesignWare DMA controller (aka
DMACA on AVR32 systems.) This DMA controller can be found integrated
on the AT32AP7000 chip and is primarily meant for peripheral DMA
transfer, but can also be used for memory-to-memory transfers.
This patch is based on a driver from David Brownell which was based on
an older version of the DMA Engine framework. It also implements the
proposed extensions to the DMA Engine API for slave DMA operations.
The dmatest client shows no problems, but there may still be room for
improvement performance-wise. DMA slave transfer performance is
definitely "good enough"; reading 100 MiB from an SD card running at ~20
MHz yields ~7.2 MiB/s average transfer rate.
Full documentation for this controller can be found in the Synopsys
DW AHB DMAC Databook:
http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf
The controller has lots of implementation options, so it's usually a
good idea to check the data sheet of the chip it's intergrated on as
well. The AT32AP7000 data sheet can be found here:
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Changes since v4:
* Use client_count instead of dma_chan_is_in_use()
* Add missing include
* Unmap buffers unless client told us not to
Changes since v3:
* Update to latest DMA engine and DMA slave APIs
* Embed the hw descriptor into the sw descriptor
* Clean up and update MODULE_DESCRIPTION, copyright date, etc.
Changes since v2:
* Dequeue all pending transfers in terminate_all()
* Rename dw_dmac.h -> dw_dmac_regs.h
* Define and use controller-specific dma_slave data
* Fix up a few outdated comments
* Define hardware registers as structs (doesn't generate better
code, unfortunately, but it looks nicer.)
* Get number of channels from platform_data instead of hardcoding it
based on CONFIG_WHATEVER_CPU.
* Give slave clients exclusive access to the channel
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>,
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds the necessary interfaces to the DMA Engine framework
to use functionality found on most embedded DMA controllers: DMA from
and to I/O registers with hardware handshaking.
In this context, hardware hanshaking means that the peripheral that
owns the I/O registers in question is able to tell the DMA controller
when more data is available for reading, or when there is room for
more data to be written. This usually happens internally on the chip,
but these signals may also be exported outside the chip for things
like IDE DMA, etc.
A new struct dma_slave is introduced. This contains information that
the DMA engine driver needs to set up slave transfers to and from a
slave device. Most engines supporting DMA slave transfers will want to
extend this structure with controller-specific parameters. This
additional information is usually passed from the platform/board code
through the client driver.
A "slave" pointer is added to the dma_client struct. This must point
to a valid dma_slave structure iff the DMA_SLAVE capability is
requested. The DMA engine driver may use this information in its
device_alloc_chan_resources hook to configure the DMA controller for
slave transfers from and to the given slave device.
A new operation for preparing slave DMA transfers is added to struct
dma_device. This takes a scatterlist and returns a single descriptor
representing the whole transfer.
Another new operation for terminating all pending transfers is added as
well. The latter is needed because there may be errors outside the scope
of the DMA Engine framework that may require DMA operations to be
terminated prematurely.
DMA Engine drivers may extend the dma_device, dma_chan and/or
dma_slave_descriptor structures to allow controller-specific
operations. The client driver can detect such extensions by looking at
the DMA Engine's struct device, or it can request a specific DMA
Engine device by setting the dma_dev field in struct dma_slave.
dmaslave interface changes since v4:
* Fix checkpatch errors
* Fix changelog (there are no slave descriptors anymore)
dmaslave interface changes since v3:
* Use dma_data_direction instead of a new enum
* Submit slave transfers as scatterlists
* Remove the DMA slave descriptor struct
dmaslave interface changes since v2:
* Add a dma_dev field to struct dma_slave. If set, the client can
only be bound to the DMA controller that corresponds to this
device. This allows controller-specific extensions of the
dma_slave structure; if the device matches, the controller may
safely assume its extensions are present.
* Move reg_width into struct dma_slave as there are currently no
users that need to be able to set the width on a per-transfer
basis.
dmaslave interface changes since v1:
* Drop the set_direction and set_width descriptor hooks. Pass the
direction and width to the prep function instead.
* Declare a dma_slave struct with fixed information about a slave,
i.e. register addresses, handshake interfaces and such.
* Add pointer to a dma_slave struct to dma_client. Can be NULL if
the DMA_SLAVE capability isn't requested.
* Drop the set_slave device hook since the alloc_chan_resources hook
now has enough information to set up the channel for slave
transfers.
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In some cases client code may need the dma-driver to skip the unmap of source
and/or destination buffers. Setting these flags indicates to the driver to
skip the unmap step. In this regard async_xor is currently broken in that it
allows the destination buffer to be unmapped while an operation is still in
progress, i.e. when the number of sources exceeds the hardware channel's
maximum (fixed in a subsequent patch).
Acked-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A DMA controller capable of doing slave transfers may need to know a
few things about the slave when preparing the channel. We don't want
to add this information to struct dma_channel since the channel hasn't
yet been bound to a client at this point.
Instead, pass a reference to the client requesting the channel to the
driver's device_alloc_chan_resources hook so that it can pick the
necessary information from the dma_client struct by itself.
[dan.j.williams@intel.com: fixed up fsldma and mv_xor]
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This client tests DMA memcpy using various lengths and various offsets
into the source and destination buffers. It will initialize both
buffers with a repeatable pattern and verify that the DMA engine copies
the requested region and nothing more. It will also verify that the
bytes aren't swapped around, and that the source buffer isn't modified.
The dmatest module can be configured to test a specific device, a
specific channel. It can also test multiple channels at the same time,
and it can start multiple threads competing for the same channel.
Changes since v2:
* Support testing multiple channels at the same time
* Support testing with multiple threads competing for the same channel
* Use counting test patterns in order to catch byte ordering issues
Changes since v1:
* Remove extra dashes around "help"
* Remove "default n" from Kconfig
* Turn TEST_BUF_SIZE into a module parameter
* Return DMA_NAK instead of DMA_DUP
* Print unhandled events
* Support testing specific channels and devices
* Move to the end of the Makefile
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The XOR engine found in Marvell's SoCs and system controllers
provides XOR and DMA operation, iSCSI CRC32C calculation, memory
initialization, and memory ECC error cleanup operation support.
This driver implements the DMA engine API and supports the following
capabilities:
- memcpy
- xor
- memset
The XOR engine can be used by DMA engine clients implemented in the
kernel, one of those clients is the RAID module. In that case, I
observed 20% improvement in the raid5 write throughput, and 40%
decrease in the CPU utilization when doing array construction, those
results obtained on an 5182 running at 500Mhz.
When enabling the NET DMA client, the performance decreased, so
meanwhile it is recommended to keep this client off.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Since 43cc71eed1, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to most
of the hotpluggable platform drivers, to re-enable auto loading.
Cc: <stable@kernel.org>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Haavard's dma-slave interface would like to test for exclusive access to a
channel. The standard channel refcounting is not sufficient in that it
tracks more than just client references, it is also inaccurate as reference
counts are percpu until the channel is removed.
This change also enables a future fix to deallocate resources when a client
declines to use a capable channel.
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The dependency is redundant since all drivers set their specific arch
dependencies. The NET_DMA option is modified to be enabled only on platforms
where it is known to have a positive effect. HAS_DMA is added as an explicit
dependency for the DMADEVICES menu.
Acked-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Set the 'parent' field of channel class devices to point to the
physical DMA device initialized by the DMA engine driver.
This allows drivers to use chan->dev.parent for syncing DMA buffers
and adds a 'device' symlink to the real device in
/sys/class/dma/dmaXchanY.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
1) Remove an explicit memset(.., 0, ...) to a variable allocated with
kzalloc (i.e. 'dest').
2) Allocate 'src' with kmalloc instead of kzalloc as all elements of the
'src' buffer are initialized in a 'for(...)' loop just after.
3) remove useless 'sizeof(u8)', which always returns 1, when computing the
size of the memory to be allocated.
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
'ack' is currently a simple integer that flags whether or not a client is done
touching fields in the given descriptor. It is effectively just a single bit
of information. Converting this to a flags parameter allows the other bits to
be put to use to control completion actions, like dma-unmap, and capture
results, like xor-zero-sum == 0.
Changes are one of:
1/ convert all open-coded ->ack manipulations to use async_tx_ack
and async_tx_test_ack.
2/ set the ack bit at prep time where possible
3/ make drivers store the flags at prep time
4/ add flags to the device_prep_dma_interrupt prototype
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
DMA drivers no longer need to be notified of dependency submission
events as async_tx_run_dependencies and async_tx_channel_switch will
handle the scheduling and execution of dependent operations.
[sfr@canb.auug.org.au: extend this for fsldma]
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Shrink struct dma_async_tx_descriptor and introduce
async_tx_channel_switch to properly inject a channel switch interrupt in
the descriptor stream. This simplifies the locking model as drivers no
longer need to handle dma_async_tx_descriptor.lock.
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Split MPC83xx EOCDI event from MPC85xx EOLNI event, which is
also need to update cookie and start the next transfer.
The DMA channel irq handler function code is refined.
The patch is tested on MPC8377MDS board.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by; Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Always enabling the fsl_dma_self_test() to ensure the DMA controller
should works well after the driver probed.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Documentation/powerpc/booting-without-of.txt specifies the
compatiables we should bind to for this driver (elo, eloplus).
Use these instead of the extremely specific 'mpc8540' and 'mpc8349'
compatiables.
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
a) every bitwise declaration will give a unique type; use typedefs.
b) no need to bother with the stuff pointed to by iomem pointers,
unless it's accessed directly. noderef will force us to use helpers
anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DMA_INTERRUPT async_tx is a NULL transfer, thus the BCR(count register)
is 0. When the transfer started with a byte count of zero, the DMA
controller will triger a PE(programming error) event and halt, not a normal
interrupt. I add special codes for PE event and DMA_INTERRUPT
async_tx testing.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The patch 'fsldma: do not cleanup descriptors in hardirq context'
(commit 222ccf9ab8) removed descriptors
cleanup function to tasklet but the completed cookie do not updated.
Thus, the DMA controller will get lots of duplicated transfer
interrupts. Just make a completed cookie update in interrupt handler.
And keep other cleanup jobs in tasklet function.
Tested-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This is a bug that I assigned DMA_INTERRUPT capability to fsldma
but missing device_prep_dma_interrupt function. For a bug in
dmaengine.c the driver passed BUG_ON() checking. The patch fixes it.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The device->device_prep_dma_interrupt function is used by
DMA_INTERRUPT capability, not DMA_ZERO_SUM.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There are warning messages reported by Stephen Rothwell with
ARCH=powerpc allmodconfig build:
drivers/dma/fsldma.c: In function 'fsl_dma_prep_memcpy':
drivers/dma/fsldma.c:439: warning: comparison of distinct pointer types
lacks a cast
drivers/dma/fsldma.c: In function 'fsl_chan_xfer_ld_queue':
drivers/dma/fsldma.c:584: warning: format '%016llx' expects type 'long long
unsigned int', but argument 4 has type 'dma_addr_t'
drivers/dma/fsldma.c: In function 'fsl_dma_chan_do_interrupt':
drivers/dma/fsldma.c:668: warning: format '%x' expects type 'unsigned int',
but argument 5 has type 'dma_addr_t'
drivers/dma/fsldma.c:684: warning: format '%016llx' expects type 'long long
unsigned int', but argument 4 has type 'dma_addr_t'
drivers/dma/fsldma.c:684: warning: format '%016llx' expects type 'long long
unsigned int', but argument 5 has type 'dma_addr_t'
drivers/dma/fsldma.c:701: warning: format '%02x' expects type 'unsigned
int', but argument 4 has type 'dma_addr_t'
drivers/dma/fsldma.c: In function 'fsl_dma_self_test':
drivers/dma/fsldma.c:840: warning: format '%d' expects type 'int', but
argument 5 has type 'size_t'
drivers/dma/fsldma.c: In function 'of_fsl_dma_probe':
drivers/dma/fsldma.c:1010: warning: format '%08x' expects type 'unsigned
int', but argument 5 has type 'resource_size_t'
This patch fixed the above warning messages.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Initialize 'ack' to zero in case the descriptor has been recycled.
Prevents "kernel BUG at crypto/async_tx/async_xor.c:185!"
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: stable@kernel.org
"Cleaning" descriptors involves calling pending callbacks and clients
assume that their callback will only ever happen in softirq context.
Delay cleanup to the tasklet.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Zhang Wei <wei.zhang@freescale.com>
The driver implements DMA engine API for Freescale MPC85xx DMA controller,
which could be used by devices in the silicon. The driver supports the
Basic mode of Freescale MPC85xx DMA controller. The MPC85xx processors
supported include MPC8540/60, MPC8555, MPC8548, MPC8641 and so on.
The MPC83xx(MPC8349, MPC8360) are also supported.
[kamalesh@linux.vnet.ibm.com: build fix]
[dan.j.williams@intel.com: merge mm fixes, rebase on async_tx-2.6.25]
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Ebony Zhu <ebony.zhu@freescale.com>
Acked-by: Kumar Gala <galak@gate.crashing.org>
Cc: Shannon Nelson <shannon.nelson@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pass a full set of flags to drivers' per-operation 'prep' routines.
Currently the only flag passed is DMA_PREP_INTERRUPT. The expectation is
that arch-specific async_tx_find_channel() implementations can exploit this
capability to find the best channel for an operation.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Reviewed-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The tx_set_src and tx_set_dest methods were originally implemented to allow
an array of addresses to be passed down from async_xor to the dmaengine
driver while minimizing stack overhead. Removing these methods allows
drivers to have all transaction parameters available at 'prep' time, saves
two function pointers in struct dma_async_tx_descriptor, and reduces the
number of indirect branches..
A consequence of moving this data to the 'prep' routine is that
multi-source routines like async_xor need temporary storage to convert an
array of linear addresses into an array of dma addresses. In order to keep
the same stack footprint of the previous implementation the input array is
reused as storage for the dma addresses. This requires that
sizeof(dma_addr_t) be less than or equal to sizeof(void *). As a
consequence CONFIG_DMADEVICES now depends on !CONFIG_HIGHMEM64G. It also
requires that drivers be able to make descriptor resources available when
the 'prep' routine is polled.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
these three list_head are all local variables, but can also use LIST_HEAD.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Shannon Nelson <shannon.nelson@intel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can't use the device in a dev_err() after a kzalloc failure or after the
kfree, so simplify it to the pdev that was originally passed in.
Cc: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few fixups from Andrew's code comments.
- removed "static inline" forward-declares
- changed use of min() to min_t()
- removed some unnecessary NULL initializations
- removed a couple of BUG() calls
Fixes this:
drivers/dma/ioat_dma.c: In function `ioat1_tx_submit':
drivers/dma/ioat_dma.c:177: sorry, unimplemented: inlining failed in call to '__ioat1_dma_memcpy_issue_pending': function body not available
drivers/dma/ioat_dma.c:268: sorry, unimplemented: called from here
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: "Williams, Dan J" <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch corrects recently changed (and now invalid) Kconfig descriptions
for the DMA engine framework:
- Non-Intel(R) hardware also has DMA engines;
- DMA is used for more than memcpy and RAID offloading.
In fact, on most platforms memcpy and RAID aren't factors, and DMA
exists so that peripherals can transfer data to/from memory while
the CPU does other work.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for version 2 of the ioatdma device. This device handles
the descriptor chain and DCA services slightly differently:
- Instead of moving the dma descriptors between a busy and an idle chain,
this new version uses a single circular chain so that we don't have
rewrite the next_descriptor pointers as we add new requests, and the
device doesn't need to re-read the last descriptor.
- The new device has the DCA tags defined internally instead of needing
them defined statically.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: "Williams, Dan J" <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a DMA device is unregistered, its reference count is decremented twice
for each channel: Once dma_class_dev_release() and once in
dma_chan_cleanup(). This may result in the DMA device driver's remove()
function completing before all channels have been cleaned up, causing lots
of use-after-free fun.
Fix it by incrementing the device's reference count twice for each
channel during registration.
[dan.j.williams@intel.com: kill unnecessary client refcounting]
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No reason I can think of of making them default y Most people don't have
the hardware and with default y they just pollute lots of configs during
make oldconfig.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: "Nelson, Shannon" <shannon.nelson@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The async_tx interface includes a completion callback. This adds support
for using that callback, including using interrupts on completion.
[akpm@linux-foundation.org: various fixes]
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The change to the async_tx interface cost this driver some performance by
spreading the descriptor setup across several functions, including multiple
passes over the new descriptor chain. Here we bring the work back into one
primary function and only do one pass.
[akpm@linux-foundation.org: cleanups, uninline]
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make better use of dev_err(), and catch an error where the transaction
creation might fail.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't start ioat_dca if ioat_dma didn't start, and then stop ioat_dca
before stopping ioat_dma. Since the ioat_dma side does the pci device
work, This takes care of ioat_dca trying to use a bad device reference.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reorder the pci release actions
Letting go of the resources in the right order helps get rid of
occasional kernel complaints.
Fix the pci_driver object name [Randy Dunlap]
Rename the struct pci_driver data so that false section mismatch
warnings won't be produced.
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adrian Bunk points out that "unsafe" was used to mark modules touched by
the deprecated MOD_INC_USE_COUNT interface, which has long gone. It's time
to remove the member from the module structure, as well.
If you want a module which can't unload, don't register an exit function.
(Vlad Yasevich says SCTP is now safe to unload, so just remove the
__unsafe there).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add code to connect to the DCA driver and provide cpu tags for use by
drivers that would like to use Direct Cache Access hints.
[Adrian Bunk] Several Kconfig cleanup items
[Andrew Morten, Chris Leech] Fix for using cpu_physical_id() even when
built for uni-processor
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for MSI and MSI-X interrupt handling, including the ability
to choose the desired interrupt method.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
[bunk@kernel.org: drivers/dma/ioat_dma.c: make 3 functions static]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split the general PCI startup from the DMA handling code in order to
prepare for adding support for DCA services and future versions of the
ioatdma device.
[Rusty Russell] Removal of __unsafe() usage.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Take care of a bunch of little code nits in ioatdma files
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename the ioatdma.c file in preparation for splitting into multiple files,
which will allow for easier adding new functionality.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add device ids for new revs of the Intel I/OAT DMA engine
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the DMA engine has a multi-client interface, fix the ioatdma
driver to play along. At the same time, remove a couple of unnecessary
reads and writes.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro pointed out that dma_memcpy_to_kernel_iovec() really was
unreachable and thus unused. The code originally was there to support
in-kernel dma needs, but since it remains unused, we'll pull it out.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Continuing the work started in 411f0f3edc ...
This enables code with a dma path, that compiles away, to build without
requiring additional code factoring. It also prevents code that calls
dma_alloc_coherent and dma_free_coherent from linking whereas previously
the code would hit a BUG() at run time. Finally, it allows archs that set
!HAS_DMA to delete their asm/dma-mapping.h file.
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: <geert@linux-m68k.org>
Cc: <zippel@linux-m68k.org>
Cc: <spyro@f2s.com>
Cc: <ysato@users.sourceforge.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: John Magolan <john.magolan@unisys.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
