We're never supposed to shrink the headroom or tailroom. In fact,
shrinking the headroom is a fatal action.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I tracked down the shutdown regression to CPUs not dying
when being shut down during power-off. This turns out to
be due to the system_state being SYSTEM_POWER_OFF, which
this code doesn't take as a valid state for shutting off
CPUs in.
This has never made sense to me, but when I added hotplug
code to implement hibernate I only "made it work" and did
not question the need to check the system_state. Thomas
Gleixner helped me dig, but the only thing we found is
that it was added with the original commit that added CPU
hotplug support.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI bridge on the Holly board is incorrectly represented in the
device tree. The current device tree node for the PCI bridge sits
under the tsi-bridge node. That's not obviously wrong, but the PCI
bridge translates some PCI spaces into CPU address ranges which were
not translated by the "ranges" property in tsi-bridge node.
We used to get away with this problem because the PCI bridge discovery
code was also buggy, assuming incorrectly that PCI host bridge nodes
were always directly under the root bus and treating the translated
addresses as raw CPU addresses, rather than parent bus addresses.
This has since been fixed, thus breaking Holly.
This could be fixed by adding extra translations to the tsi-bridge
node, but this patch instead moves the Holly PCI bridge out of the
tsi-bridge node to the root bus. This makes the tsi-bridge node
represent only the built-in IO devices in the bridge, with a
more-or-less contiguous address range. This is the same convention
used on Freescale SoC chips, where the "soc" node represents only the
IMMR region, and the PCI and other bus bridges are separate nodes
under the root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Initial fix for making sure that we can access percpu variables
in all C code (commit: 10617bbe84)
inadvertantly allocated the memory in the "percpu" section of
the vmlinux ELF executable. This confused kexec/dump.
Signed-off-by: Tony Luck <tony.luck@intel.com>
There's a race between mm->owner assignment and swapoff, more easily
seen when task slab poisoning is turned on. The condition occurs when
try_to_unuse() runs in parallel with an exiting task. A similar race
can occur with callers of get_task_mm(), such as /proc/<pid>/<mmstats>
or ptrace or page migration.
CPU0 CPU1
try_to_unuse
looks at mm = task0->mm
increments mm->mm_users
task 0 exits
mm->owner needs to be updated, but no
new owner is found (mm_users > 1, but
no other task has task->mm = task0->mm)
mm_update_next_owner() leaves
mmput(mm) decrements mm->mm_users
task0 freed
dereferencing mm->owner fails
The fix is to notify the subsystem via mm_owner_changed callback(),
if no new owner is found, by specifying the new task as NULL.
Jiri Slaby:
mm->owner was set to NULL prior to calling cgroup_mm_owner_callbacks(), but
must be set after that, so as not to pass NULL as old owner causing oops.
Daisuke Nishimura:
mm_update_next_owner() may set mm->owner to NULL, but mem_cgroup_from_task()
and its callers need to take account of this situation to avoid oops.
Hugh Dickins:
Lockdep warning and hang below exec_mmap() when testing these patches.
exit_mm() up_reads mmap_sem before calling mm_update_next_owner(),
so exec_mmap() now needs to do the same. And with that repositioning,
there's now no point in mm_need_new_owner() allowing for NULL mm.
Reported-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
cdrom: update ioctl documentation
ide: note that IDE generic may prevent other drivers from attaching
ide-tape: fix vendor strings
Swarm: Fix crash due to missing initialization
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[SSB] Initialise dma_mask for SSB_BUSTYPE_SSB devices
[MIPS] BCM47xx: Fix build error due to missing PCI functions
[MIPS] IP27: Switch to dynamic interrupt routing avoding panic on error.
[MIPS] au1000: Make sure GPIO value is zero or one
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdboc,tty: Fix tty polling search to use name correctly
kgdb, x86_64: fix PS CS SS registers in gdb serial
kgdb, x86_64: gdb serial has BX and DX reversed
kgdb, x86, arm, mips, powerpc: ignore user space single stepping
kgdb: could not write to the last of valid memory with kgdb
Impact: per CPU hrtimers can be migrated from a dead CPU
The hrtimer code has no knowledge about per CPU timers, but we need to
prevent the migration of such timers and warn when such a timer is
active at migration time.
Explicitely mark the timers as per CPU and use a more understandable
mode descriptor for the interrupts safe unlocked callback mode, which
is used by hrtimer_sleeper and the scheduler code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: during migration active hrtimers can be seen as inactive
The migration code removes the hrtimers from the queues of the dead
CPU and sets the state temporary to INACTIVE. The enqueue code sets it
to ACTIVE/PENDING again.
Prevent that the wrong state can be seen by using a separate migration
state bit.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: Stale timers after a CPU went offline.
commit 37bb6cb409
hrtimer: unlock hrtimer_wakeup
changed the hrtimer sleeper callback mode to CB_IRQSAFE_NO_SOFTIRQ due
to locking problems. A result of this change is that when enqueue is
called for an already expired hrtimer the callback function is not
longer called directly from the enqueue code. The normal callers have
been fixed in the code, but the migration code which moves hrtimers
from a dead CPU to a live CPU was not made aware of this.
This can be fixed by checking the timer state after the call to
enqueue in the migration code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: hrtimers which are on the pending list are not migrated at cpu
offline and can be stale forever
Add the pending list migration when CONFIG_HIGH_RES_TIMERS is enabled
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ASoC: Fix another cs4270 error path
ALSA: make the CS4270 driver a new-style I2C driver
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] qlogicpti: fix sg list traversal error in continuation entries
[SCSI] Fix hang with split requests
[SCSI] qla2xxx: Defer enablement of RISC interrupts until ISP initialization completes.
Commit f072181e64 ("kconfig: drop the
""trying to assign nonexistent symbol" warning") simply dropped the
warnings, but it does a little more than that, it also marks the current
.config as needed saving, so add this back.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent changes to oldconfig have mixed up the silentoldconfig handling,
so this fixes that by clearly separating that special mode, e.g.
KCONFIG_NOSILENTUPDATE is only relevant here, the .config is written as
needed.
This will also properly close Bug 11230.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The VFS interface for the 'd_compare()' is a bit special (read: 'odd'),
because it really just essentially replaces a memcmp(). The filesystem
is supposed to just compare the two names with whatever case-independent
or other function.
And when I say 'is supposed to', I obviously mean that 'procfs does odd
things, and actually looks at the dentry that we don't even pass down,
rather than just the name'. Which results in problems, because we
actually call d_compare before we have even verified that the dentry is
still hashed at all.
And that causes a problm since the inode that procfs looks at may have
been free'd and the d_inode pointer is NULL. procfs just assumes that
all dentries are positive, since procfs itself never generates a
negative one. But memory pressure will still result in the dentry
getting torn down, and as it is removed by RCU, it still remains visible
on some lists - and to d_compare.
If the filesystem just did a name comparison, we wouldn't care. And we
could just fix procfs to know about negative dentries too. But rather
than have the low-level filesystems know about internal VFS details,
just move the check for a unhashed dentry up a bit, so that we will only
call d_compare on dentries that are still active.
The actual oops this caused didn't look like a NULL pointer dereference
because procfs did a 'container_of(inode, struct proc_inode, vfs_inode)'
to get at its internal proc_inode information from the inode pointer,
and accessed a field below the inode. So the oops would look something
like
BUG: unable to handle kernel paging request at fffffffffffffff0
IP: [<ffffffff802bc6c6>] proc_sys_compare+0x36/0x50
and was seen on both x86-64 (Alexey Dobriyan and Hugh Dickins) and
ppc64 (Hugh Dickins).
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-of-by: Linus Torvalds <torvalds@linux-foundation.org>
Exposure was always 0. Thanks to sparse for finding this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The device 2040:2950 is a really old variant of the PVR USB2 hardware.
I have just learned of its existence. For the purposes of the pvrusb2
driver, it is functionally identical to the well known 29xxx series
(2040:2900). Amazing that this went undetected for 3+ years.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Conversion to new-style i2c driver missed the error path of the
probe function. Fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update the CS4270 ALSA device driver to use the new-style I2C interface.
Starting with the 2.6.27 PowerPC kernel, I2C devices that have entries in the
device trees can no longer be probed by old-style I2C drivers. The device
tree for Freescale MPC8610 HPCD has included an entry for the CS4270 since
2.6.25, but that entry was previously ignored by the PowerPC I2C subsystem.
Since that's no longer the case, the best solution is to update the CS4270
driver to a new-style interface, rather than try to revert the behavior of
new PowerPC I2C subsystem.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Boaz writes:
"I've reviewed all patches since Matthew's, and I find one small
problem.
In the load_cmd() there is a compound loop where the first 4 sg's are
set then the rest are set into a memory structure in group of 7 sg's.
Well the second 7-group and on is a bug because sg pointer does not advance.
This is a fall out from Jens's patch."
The reporter, Meelis Roos <mroos@ut.ee>, verified that this patch
does indeed fix his problem with qlogicpti.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commit 2fd673ecf0 which tried to remove
hardreset for generic accidentally removed it for all flavors as all
others were inheriting from nv_generic_ops. This patch reinstates
nv_hardreset() and puts it into nv_common_ops which all flavors
inherit from. nv_generic_ops now inherits from nv_common_ops and
overrides .hardreset to ATA_OP_NULL.
While at it, explain why nv_hardreset and ATA_OP_NULL override are
necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The current sg list traversal logic for the continuation entries
doesn't advance the list pointer once all seven slots are used, so the
next continuation entry (if there is one) wrongly begins again at the
start of the sg list.
Fix by advancing the sg pointer after the for_each_sg().
Reported-by: Meelis Roos <mroos@ut.ee>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Correct copy-paste problem: CDROMCLOSETRAY is about closing the tray,
not opening it.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Enabling IDE generic may prevent ATA controllers located on legacy
ports from being attached to more proper driver or can prevent other
controllers which share the IRQ from working. Note it in the help
message.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: xerces8 <xerces8@butn.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: stein@hermes.si
[bart: s/will grab/may grab/ since Borislav has fixed PCI-case for .28]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove superfluous two bytes from each string buffer and add proper length
format specifiers.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Tested-by: Mark de Wever <koraq@xs4all.nl>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If things are just right this will result in the hws[0]->parent being
passed to ide_host_add() being non-zero and an ooops a little later.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
For SSB_BUSTYPE_SSB type devices, we need to initialize dma_mask using
coherent_dma_mask so that calls to dma_set_mask() succeed.
It fixes the regression on the b44 driver introduced by commit
f225763a7d
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch defines pcibios_map_irq() and pcibios_plat_dev_init() for
the BCM47xx platform.
It fixes the regression introduced by commit
aab547ce0d.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
pcibios_map_irq is no way of returning an error but on IP27 an interrupt
is possibly not routable when running out of resources. So do the
interrupt routing at pcibios_enable_device time.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Brownell <david-b@pacbell.net> wrote:
> The problem is that "value" is zero-or-nonzero.
> This code wrongly assumes it's zero-or-one.
> Possible fix: "((!!value) << gpio)".
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
