This driver register pm_power_off with snvs power off function. If
your boards NOT use PMIC_ON_REQ to turn on/off external pmic, or use
other pin to do, please disable the driver in dts, otherwise, your
pm_power_off maybe overwrote by this driver.
Signed-off-by: Robin Gong <b38343@freescale.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The SIMPLE_DEV_PM_OPS() macro already takes care of the CONFIG_PM_SLEEP=n case,
so we can simplify the code a little bit.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Register with kernel restart handler instead of setting arm_pm_restart directly.
Move notifier registration to the end of the probe function to avoid having to
implement error handling.
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Register with kernel restart handler instead of setting arm_pm_restart directly.
This patch also addresses the following compile warning.
drivers/power/reset/xgene-reboot.c: In function 'xgene_reboot_probe':
drivers/power/reset/xgene-reboot.c:77:17: warning:
assignment from incompatible pointer type [enabled by default]
The warning was due to a mismatch between the type of arm_pm_restart
and the restart function.
Cc: Loc Ho <lho@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
jiffies are not running at this stage of system shutdown, meaning an
error in the reset function would never be reported. Replace with mdelay().
Cc: Loc Ho <lho@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using a local variable dev to point to the device is simpler then repeatedly
dereferencing pdev->dev.
Cc: Loc Ho <lho@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is customary to return an error code of -ENOMEM if the system
is out of memory. Also, in that case, the infrastructure will report
an error, so it is unnecessary to report it again.
Cc: Loc Ho <lho@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the kernel restart handler instead of setting arm_pm_restart directly.
This allows for more than one restart handler in the system.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver register pm_power_off with snvs power off function. If
your boards NOT use PMIC_ON_REQ to turn on/off external pmic, or use
other pin to do, please disable the driver in dts, otherwise, your
pm_power_off maybe overwrote by this driver.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add the ability to parse gpio-charger data from a devicetree node.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Move the (DDR) SDRAM controller headers to include/soc/at91 to remove the
dependency on mach/ headers from the at91-reset driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The charger manager obtained reference to fuel gauge power supply in probe
with power_supply_get_by_name() for later usage. However if fuel gauge
driver was removed and re-added then this reference would point to old
power supply (from driver which was removed).
This lead to accessing old (and probably invalid) memory which could be
observed with:
$ echo "12-0036" > /sys/bus/i2c/drivers/max17042/unbind
$ echo "12-0036" > /sys/bus/i2c/drivers/max17042/bind
$ cat /sys/devices/virtual/power_supply/battery/capacity
[ 240.480084] INFO: task cat:1393 blocked for more than 120 seconds.
[ 240.484799] Not tainted 3.17.0-next-20141007-00028-ge60b6dd79570 #203
[ 240.491782] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.499589] cat D c0469530 0 1393 1 0x00000000
[ 240.505947] [<c0469530>] (__schedule) from [<c0469d3c>] (schedule_preempt_disabled+0x14/0x20)
[ 240.514449] [<c0469d3c>] (schedule_preempt_disabled) from [<c046af08>] (mutex_lock_nested+0x1bc/0x458)
[ 240.523736] [<c046af08>] (mutex_lock_nested) from [<c0287a98>] (regmap_read+0x30/0x60)
[ 240.531647] [<c0287a98>] (regmap_read) from [<c032238c>] (max17042_get_property+0x2e8/0x350)
[ 240.540055] [<c032238c>] (max17042_get_property) from [<c03247d8>] (charger_get_property+0x264/0x348)
[ 240.549252] [<c03247d8>] (charger_get_property) from [<c0320764>] (power_supply_show_property+0x48/0x1e0)
[ 240.558808] [<c0320764>] (power_supply_show_property) from [<c027308c>] (dev_attr_show+0x1c/0x48)
[ 240.567664] [<c027308c>] (dev_attr_show) from [<c0141fb0>] (sysfs_kf_seq_show+0x84/0x104)
[ 240.575814] [<c0141fb0>] (sysfs_kf_seq_show) from [<c0140b18>] (kernfs_seq_show+0x24/0x28)
[ 240.584061] [<c0140b18>] (kernfs_seq_show) from [<c0104574>] (seq_read+0x1b0/0x484)
[ 240.591702] [<c0104574>] (seq_read) from [<c00e1e24>] (vfs_read+0x88/0x144)
[ 240.598640] [<c00e1e24>] (vfs_read) from [<c00e1f20>] (SyS_read+0x40/0x8c)
[ 240.605507] [<c00e1f20>] (SyS_read) from [<c000e760>] (ret_fast_syscall+0x0/0x48)
[ 240.612952] 4 locks held by cat/1393:
[ 240.616589] #0: (&p->lock){+.+.+.}, at: [<c01043f4>] seq_read+0x30/0x484
[ 240.623414] #1: (&of->mutex){+.+.+.}, at: [<c01417dc>] kernfs_seq_start+0x1c/0x8c
[ 240.631086] #2: (s_active#31){++++.+}, at: [<c01417e4>] kernfs_seq_start+0x24/0x8c
[ 240.638777] #3: (&map->mutex){+.+...}, at: [<c0287a98>] regmap_read+0x30/0x60
The charger-manager should get reference to fuel gauge power supply on
each use of get_property callback. The thermal zone 'tzd' field of
power supply should not be used because of the same reason.
Additionally this change solves also the issue with nested
thermal_zone_get_temp() calls and related false lockdep positive for
deadlock for thermal zone's mutex [1]. When fuel gauge is used as source of
temperature then the charger manager forwards its get_temp calls to fuel
gauge thermal zone. So actually different mutexes are used (one for
charger manager thermal zone and second for fuel gauge thermal zone) but
for lockdep this is one class of mutex.
The recursion is removed by retrieving temperature through power
supply's get_property().
In case external thermal zone is used ('cm-thermal-zone' property is
present in DTS) the recursion does not exist. Charger manager simply
exports POWER_SUPPLY_PROP_TEMP_AMBIENT property (instead of
POWER_SUPPLY_PROP_TEMP) thus no thermal zone is created for this power
supply.
[1] https://lkml.org/lkml/2014/10/6/309
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: 3bb3dbbd56 ("power_supply: Add initial Charger-Manager driver")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The charger manager supports POWER_SUPPLY_PROP_TEMP property and acts
as a thermal zone if any of these conditions match:
1. Fuel gauge used by charger manager supports POWER_SUPPLY_PROP_TEMP.
2. 'cm-thermal-zone' property is present in DTS (then it will supersede
the fuel gauge temperature property).
However in case 1 (fuel gauge reports temperature and 'cm-thermal-zone'
is not set) the charger manager forwards its get_temp calls to fuel
gauge thermal zone.
This leads to reporting by lockdep a false positive deadlock for thermal
zone's mutex because of nested calls to thermal_zone_get_temp(). This is
false positive because these are different mutexes: one for charger
manager thermal zone and second for fuel gauge thermal zone.
Get rid of false lockdep alert and recursive call by setting
'no_thermal' property for this power supply class. The thermal zone for
charger manager won't be created (user space does not use it anyway).
The lockdep report:
[ 2.540339] charger-manager charger-manager@0: Ignoring full-battery voltage threshold as it is not supplied
[ 2.540351] charger-manager charger-manager@0: Ignoring full-battery full capacity threshold as it is not supplied
[ 2.546296]
[ 2.546302] =============================================
[ 2.546305] [ INFO: possible recursive locking detected ]
[ 2.546312] 3.17.0-rc6-next-20140926-00012-gbb13895e46af-dirty #39 Not tainted
[ 2.546316] ---------------------------------------------
[ 2.546321] swapper/0/1 is trying to acquire lock:
[ 2.546348] (&tz->lock){+.+...}, at: [<c0321d24>] thermal_zone_get_temp+0x38/0x68
[ 2.546352]
[ 2.546352] but task is already holding lock:
[ 2.546369] (&tz->lock){+.+...}, at: [<c0321d24>] thermal_zone_get_temp+0x38/0x68
[ 2.546373]
[ 2.546373] other info that might help us debug this:
[ 2.546376] Possible unsafe locking scenario:
[ 2.546376]
[ 2.546378] CPU0
[ 2.546380] ----
[ 2.546386] lock(&tz->lock);
[ 2.546392] lock(&tz->lock);
[ 2.546394]
[ 2.546394] *** DEADLOCK ***
[ 2.546394]
[ 2.546397] May be due to missing lock nesting notation
[ 2.546397]
[ 2.546401] 2 locks held by swapper/0/1:
[ 2.546430] #0: (&dev->mutex){......}, at: [<c02720c4>] __driver_attach+0x58/0x98
[ 2.546448] #1: (&tz->lock){+.+...}, at: [<c0321d24>] thermal_zone_get_temp+0x38/0x68
[ 2.546451]
[ 2.546451] stack backtrace:
[ 2.546460] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.17.0-rc6-next-20140926-00012-gbb13895e46af-dirty #39
[ 2.546497] [<c00140f0>] (unwind_backtrace) from [<c0011228>] (show_stack+0x10/0x14)
[ 2.546526] [<c0011228>] (show_stack) from [<c046158c>] (dump_stack+0x70/0xbc)
[ 2.546554] [<c046158c>] (dump_stack) from [<c005e32c>] (validate_chain.isra.24+0x718/0x890)
[ 2.546569] [<c005e32c>] (validate_chain.isra.24) from [<c005f0a0>] (__lock_acquire+0x498/0xa78)
[ 2.546581] [<c005f0a0>] (__lock_acquire) from [<c005fb50>] (lock_acquire+0x78/0xb8)
[ 2.546594] [<c005fb50>] (lock_acquire) from [<c0464260>] (mutex_lock_nested+0x64/0x458)
[ 2.546605] [<c0464260>] (mutex_lock_nested) from [<c0321d24>] (thermal_zone_get_temp+0x38/0x68)
[ 2.546634] [<c0321d24>] (thermal_zone_get_temp) from [<c031f1e0>] (charger_get_property+0x10c/0x348)
[ 2.546649] [<c031f1e0>] (charger_get_property) from [<c031af18>] (power_supply_read_temp+0x28/0x58)
[ 2.546662] [<c031af18>] (power_supply_read_temp) from [<c0321d38>] (thermal_zone_get_temp+0x4c/0x68)
[ 2.546676] [<c0321d38>] (thermal_zone_get_temp) from [<c03233d8>] (thermal_zone_device_update+0x24/0x9c)
[ 2.546687] [<c03233d8>] (thermal_zone_device_update) from [<c0323874>] (thermal_zone_device_register+0x424/0x550)
[ 2.546701] [<c0323874>] (thermal_zone_device_register) from [<c031b3c0>] (__power_supply_register+0x2a4/0x348)
[ 2.546714] [<c031b3c0>] (__power_supply_register) from [<c031ff64>] (charger_manager_probe+0x600/0xe5c)
[ 2.546727] [<c031ff64>] (charger_manager_probe) from [<c0273384>] (platform_drv_probe+0x48/0xa4)
[ 2.546746] [<c0273384>] (platform_drv_probe) from [<c0271f54>] (driver_probe_device+0x10c/0x224)
[ 2.546760] [<c0271f54>] (driver_probe_device) from [<c0272100>] (__driver_attach+0x94/0x98)
[ 2.546772] [<c0272100>] (__driver_attach) from [<c0270780>] (bus_for_each_dev+0x54/0x88)
[ 2.546784] [<c0270780>] (bus_for_each_dev) from [<c027173c>] (bus_add_driver+0xd4/0x1d0)
[ 2.546797] [<c027173c>] (bus_add_driver) from [<c027271c>] (driver_register+0x78/0xf4)
[ 2.546809] [<c027271c>] (driver_register) from [<c0008984>] (do_one_initcall+0x80/0x1d4)
[ 2.546829] [<c0008984>] (do_one_initcall) from [<c0612d60>] (kernel_init_freeable+0x10c/0x1d8)
[ 2.546847] [<c0612d60>] (kernel_init_freeable) from [<c045c238>] (kernel_init+0x8/0xec)
[ 2.546863] [<c045c238>] (kernel_init) from [<c000e828>] (ret_from_fork+0x14/0x2c)
[ 2.551396] charger-manager charger-manager@0: 'chg-reg' regulator's externally_control is 0
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add a 'no_thermal' property to the power supply class. If true then
thermal zone won't be created for this power supply in
power_supply_register().
Power supply drivers may want to set it if they support
POWER_SUPPLY_PROP_TEMP and they are forwarding this get property call to
other thermal zone.
If they won't set it lockdep may report false positive deadlock for
thermal zone's mutex because of nested calls to thermal_zone_get_temp().
First is the call to thermal_zone_get_temp() of the driver's thermal
zone. Thermal core gets POWER_SUPPLY_PROP_TEMP property from this
driver. The driver then calls other thermal zone thermal_zone_get_temp()
and returns result.
Example of such driver is charger manager.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Memory allocated for 'name' was leaking if required binding properties
were not present.
The memory for 'name' was allocated early at probe with kasprintf(). It
was freed in error paths executed before and after parsing DTS but not
in that error path.
Fix the error path for parsing device tree properties.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: faffd234cf ("bq2415x_charger: Add DT support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The power_supply_get_by_phandle() on error returns ENODEV or NULL.
The driver later expects obtained pointer to power supply to be
valid or NULL. If it is not NULL then it dereferences it in
bq2415x_notifier_call() which would lead to dereferencing ENODEV-value
pointer.
Properly handle the power_supply_get_by_phandle() error case by
replacing error value with NULL. This indicates that usb charger
detection won't be used.
Fix also memory leak of 'name' if power_supply_get_by_phandle() fails
with NULL and probe should defer.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: faffd234cf ("bq2415x_charger: Add DT support")
Cc: <stable@vger.kernel.org>
[small fix regarding the missing ti,usb-charger-detection info message]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
In the case of at91sam9g45_restart(), the driver is writing
AT91_DDRSDRC_LPCB_POWER_DOWN to AT91_DDRSDRC_RTR, this should actually be
AT91_DDRSDRC_LPR.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch changes 32-bit time types to 64-bit in
drivers/power/ab8500_fg.c
timespec and time_t can only represent signed 32-bit
dates but the driver should represent dates that are
after January 2038. So used time64.h header file and
its proper types and functions.
Use time64_t type instead of __kernel_time_t for
time_stamps variable of ab8500_fg_avg_cap struct
Signed-off-by: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cP1w
-----END PGP SIGNATURE-----
Merge tag 'restart-handler-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull restart handler infrastructure from Guenter Roeck:
"This series was supposed to be pulled through various trees using it,
and I did not plan to send a separate pull request. As it turns out,
the pinctrl tree did not merge with it, is now upstream, and uses it,
meaning there are now build failures.
Please pull this series directly to fix those build failures"
* tag 'restart-handler-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
arm/arm64: unexport restart handlers
watchdog: sunxi: register restart handler with kernel restart handler
watchdog: alim7101: register restart handler with kernel restart handler
watchdog: moxart: register restart handler with kernel restart handler
arm: support restart through restart handler call chain
arm64: support restart through restart handler call chain
power/restart: call machine_restart instead of arm_pm_restart
kernel: add support for kernel restart handler call chain
- Rework the handling of wakeup IRQs by the IRQ core such that
all of them will be switched over to "wakeup" mode in
suspend_device_irqs() and in that mode the first interrupt
will abort system suspend in progress or wake up the system
if already in suspend-to-idle (or equivalent) without executing
any interrupt handlers. Among other things that eliminates the
wakeup-related motivation to use the IRQF_NO_SUSPEND interrupt
flag with interrupts which don't really need it and should not
use it (Thomas Gleixner and Rafael J Wysocki).
- Switch over ACPI to handling wakeup interrupts with the help
of the new mechanism introduced by the above IRQ core rework
(Rafael J Wysocki).
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during
enumeration (Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in
the METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot
(or after resume from system suspend) and rework the ACPI Smart
Battery Subsystem (SBS) driver to work correctly with Apple
platforms (Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the
code, adding support for 133MHz I2C source clock on Intel Baytrail
to it and making it avoid using UART RTS override with Auto Flow
Control (Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak).
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin).
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui).
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes).
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name
change among other things), ppc-corenet, powernv (Viresh Kumar,
Preeti U Murthy, Shilpasri G Bhat, Lucas Stach).
- cpuidle support for DT-based idle states infrastructure, new
ARM64 cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi,
Rasmus Villemoes).
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman).
- Rework of the test_suspend kernel command line argument and
a new trace event for console resume (Srinivas Pandruvada,
Todd E Brandt).
- Second attempt to optimize swsusp_free() (hibernation core) to
make it avoid going through all PFNs which may be way too slow on
some systems (Joerg Roedel).
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS
entry update in MAINTAINERS (Heiko Stübner, Kevin Hilman).
- PM core fix related to clock management (Geert Uytterhoeven).
- PM core's sysfs code cleanup (Johannes Berg).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=sIv/
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Features-wise, to me the most important this time is a rework of
wakeup interrupts handling in the core that makes them work
consistently across all of the available sleep states, including
suspend-to-idle. Many thanks to Thomas Gleixner for his help with
this work.
Second is an update of the generic PM domains code that has been in
need of some care for quite a while. Unused code is being removed, DT
support is being added and domains are now going to be attached to
devices in bus type code in analogy with the ACPI PM domain. The
majority of work here was done by Ulf Hansson who also has been the
most active developer this time.
Apart from this we have a traditional ACPICA update, this time to
upstream version 20140828 and a few ACPI wakeup interrupts handling
patches on top of the general rework mentioned above. There also are
several cpufreq commits including renaming the cpufreq-cpu0 driver to
cpufreq-dt, as this is what implements generic DT-based cpufreq
support, and a new DT-based idle states infrastructure for cpuidle.
In addition to that, the ACPI LPSS driver is updated, ACPI support for
Apple machines is improved, a few bugs are fixed and a few cleanups
are made all over.
Finally, the Adaptive Voltage Scaling (AVS) subsystem now has a tree
maintained by Kevin Hilman that will be merged through the PM tree.
Numbers-wise, the generic PM domains update takes the lead this time
with 32 non-merge commits, second is cpufreq (15 commits) and the 3rd
place goes to the wakeup interrupts handling rework (13 commits).
Specifics:
- Rework the handling of wakeup IRQs by the IRQ core such that all of
them will be switched over to "wakeup" mode in suspend_device_irqs()
and in that mode the first interrupt will abort system suspend in
progress or wake up the system if already in suspend-to-idle (or
equivalent) without executing any interrupt handlers. Among other
things that eliminates the wakeup-related motivation to use the
IRQF_NO_SUSPEND interrupt flag with interrupts which don't really
need it and should not use it (Thomas Gleixner and Rafael Wysocki)
- Switch over ACPI to handling wakeup interrupts with the help of the
new mechanism introduced by the above IRQ core rework (Rafael Wysocki)
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during enumeration
(Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in the
METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot (or
after resume from system suspend) and rework the ACPI Smart Battery
Subsystem (SBS) driver to work correctly with Apple platforms
(Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the code,
adding support for 133MHz I2C source clock on Intel Baytrail to it
and making it avoid using UART RTS override with Auto Flow Control
(Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak)
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin)
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui)
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes)
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name change
among other things), ppc-corenet, powernv (Viresh Kumar, Preeti U
Murthy, Shilpasri G Bhat, Lucas Stach)
- cpuidle support for DT-based idle states infrastructure, new ARM64
cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi, Rasmus
Villemoes)
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman)
- Rework of the test_suspend kernel command line argument and a new
trace event for console resume (Srinivas Pandruvada, Todd E Brandt)
- Second attempt to optimize swsusp_free() (hibernation core) to make
it avoid going through all PFNs which may be way too slow on some
systems (Joerg Roedel)
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS entry
update in MAINTAINERS (Heiko Stübner, Kevin Hilman)
- PM core fix related to clock management (Geert Uytterhoeven)
- PM core's sysfs code cleanup (Johannes Berg)"
* tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (105 commits)
ACPI / fan: printk replacement
PM / clk: Fix crash in clocks management code if !CONFIG_PM_RUNTIME
PM / Domains: Rename cpu_data to cpuidle_data
cpufreq: cpufreq-dt: fix potential double put of cpu OF node
cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'
PM / hibernate: Iterate over set bits instead of PFNs in swsusp_free()
cpufreq: ppc-corenet: remove duplicate update of cpu_data
ACPI / sleep: Rework the handling of ACPI GPE wakeup from suspend-to-idle
PM / sleep: Rename platform suspend/resume functions in suspend.c
PM / sleep: Export dpm_suspend_late/noirq() and dpm_resume_early/noirq()
ACPICA: Introduce acpi_enable_all_wakeup_gpes()
ACPICA: Clear all non-wakeup GPEs in acpi_hw_enable_wakeup_gpe_block()
ACPI / video: check _DOD list when creating backlight devices
PM / Domains: Move dev_pm_domain_attach|detach() to pm_domain.h
cpufreq: Replace strnicmp with strncasecmp
cpufreq: powernv: Set the cpus to nominal frequency during reboot/kexec
cpufreq: powernv: Set the pstate of the last hotplugged out cpu in policy->cpus to minimum
cpufreq: Allow stop CPU callback to be used by all cpufreq drivers
PM / devfreq: exynos: Enable building exynos PPMU as module
PM / devfreq: Export helper functions for drivers
...
Fix
drivers/power/ab8500_fg.c: In function 'ab8500_fg_probe':
drivers/power/ab8500_fg.c:2989:27:
warning: 'i' may be used uninitialized in this function
drivers/power/ab8500_fg.c:2972:15: note: 'i' was declared here
which actually points to a real bug.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch is to fix some bugs in reboot driver. Which includes auto selection
of the MFD_SYSCON for the driver, use of container to locate restart handler,
correction of the count down failure timer and ordering of the header file.
Signed-off-by: Feng Kan <fkan@apm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
[ sre: return err instead of 0 in syscon_reboot_probe() ]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch fix the following issues.
- Flag for bq27742 is 2 bytes contracy to 1 byte for older hardware
- Don't read FLAG_CI as bq27742 does not have it
- Use Battery full capacity register as last measure discharge
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This change replaces use of arm_pm_restart with recently introduced
reset mechanism in Linux kernel called restart_notifier.
Choosing priority 128, which is default priority, as according to
documentation, this mechanism is sufficient to restart the entire system.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Josh Cartwright <joshc@codeaurora.org>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-pm@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This driver registers a restart handler to set a GPIO line high/low
to reset a board based on devicetree bindings.
Signed-off-by: David Riley <davidriley@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This driver adds the restart functionality for STiH415 and STiH416
platforms from STMicroelectronics. This driver registers an
arm_pm_restart function to reset the platform.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
machine_restart is supported on non-ARM platforms, and and ultimately
calls arm_pm_restart, so dont call arm_pm_restart directly but use the
more generic function.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This driver enabled us to drive the reboot of the Versatile family
of ARM reference boards. Even though only the RealView boards are
supported initially, these boards all have the same procedure for
reboot:
- Write a magic value into an unlocking register
- Write another magic value into a reset control register
The driver will be reusable for Versatile and possibly also the
Integrator family of reference boards.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
IO domain voltages on some Rockchip SoCs are variable but need to be
kept in sync between the regulators and the SoC using a special
register.
A specific example using rk3288:
- If the regulator hooked up to a pin like SDMMC0_VDD is 3.3V then
bit 7 of GRF_IO_VSEL needs to be 0. If the regulator hooked up to
that same pin is 1.8V then bit 7 of GRF_IO_VSEL needs to be 1.
Said another way, this driver simply handles keeping bits in the SoC's
general register file (GRF) in sync with the actual value of a voltage
hooked up to the pins.
Note that this driver specifically doesn't include:
- any logic for deciding what voltage we should set regulators to
- any logic for deciding whether regulators (or internal SoC blocks)
should have power or not have power
If there were some other software that had the smarts of making
decisions about regulators, it would work in conjunction with this
driver. When that other software adjusted a regulator's voltage then
this driver would handle telling the SoC about it. A good example is
vqmmc for SD. In that case the dw_mmc driver simply is told about a
regulator. It changes the regulator between 3.3V and 1.8V at the
right time. This driver notices the change and makes sure that the
SoC is on the same page.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[khilman: fix compiler warnings]
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Make the max14577 charger driver depending on SYSFS instead selecting
it. This fixes warning on x86_64 with allmodconfig:
scripts/kconfig/conf --allmodconfig Kconfig
fs/sysfs/Kconfig:1:error: recursive dependency detected!
fs/sysfs/Kconfig:1: symbol SYSFS is selected by CHARGER_MAX14577
drivers/power/Kconfig:327: symbol CHARGER_MAX14577 depends on POWER_SUPPLY
drivers/power/Kconfig:1: symbol POWER_SUPPLY is selected by HID_SONY
drivers/hid/Kconfig:638: symbol HID_SONY depends on NEW_LEDS
drivers/leds/Kconfig:8: symbol NEW_LEDS is selected by SENSORS_APPLESMC
drivers/hwmon/Kconfig:299: symbol SENSORS_APPLESMC depends on HWMON
drivers/hwmon/Kconfig:5: symbol HWMON is selected by EEEPC_LAPTOP
drivers/platform/x86/Kconfig:496: symbol EEEPC_LAPTOP depends on HOTPLUG_PCI
drivers/pci/hotplug/Kconfig:5: symbol HOTPLUG_PCI depends on SYSFS
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Some gpio implementations return interesting values for gpio_get_value when
the value is not 0 - as seen on a imx6sl board. Therefore do not use the
value returned from gpio_get_value directly but simply check for 0 or not 0.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use of_get_child_by_name to obtain reference to charger node instead of
of_find_node_by_name which can walk outside of the parent node.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Check the return value of devm_kzalloc() to fix possible NULL pointer
dereference and properly exit the probe() on memory allocation failure.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add support to bq27742 in bq27x00 driver. bq27742 register
addresses are mostly mostly the same as bq27500 addresses
with minor differences.
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Rhyland Klein <rklein@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
MAX77836 has the same Fuel Gauge as MAX17040/17048. The max17040 driver
can be safely re-used. The patch adds MAX77836 device to the array of
i2c_device_id. Additionally it removes the id associated with MAX17040
device as the value is not used.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove hard-coded values for:
- Fast Charge current,
- End Of Charge current,
- Fast Charge timer,
- Overvoltage Protection Threshold,
- Battery Constant Voltage,
and use DTS or sysfs to configure them. This allows using the max14577 charger
driver with different batteries.
Now the charger driver requires valid configuration data from DTS. In
case of wrong configuration data it fails during probe.
The fast charge timer is configured through sysfs entry.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for MAX77836 charger to the max14577 driver. The MAX77836
charger is almost the same as 14577 model except:
- No dead-battery detection;
- Support for special charger (like in MAX77693);
- Support for DX over-voltage protection (like in MAX77693);
- Lower values of charging current (two times lower current for
slow/fast charge, much lower EOC current);
- Slightly different values in ChgTyp field of STATUS2 register. On
MAX14577 0x6 is reserved and 0x7 dead battery. On the MAX77836 the
0x6 means special charger and 0x7 is reserved. Regardless of these
differences the driver maps them to one enum max14577_muic_charger_type.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds a driver for the LTC2952, an external power control chip,
which signals the OS to shut down. Additionally this driver lets the
kernel power down the board.
Signed-off-by: René Moll <rene.moll@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This piece of code was added so that we return -EPROBE_DEFER when no devices are
registered. But even if class_for_each_device() returns 0, we are going to
return -EPROBE_DEFER only.
And so this code isn't required at all. Remove it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Using 'goto' statements for freeing resources on failures is a good choice as it
makes code very clean, and reduces the chances of human errors.
Though in most cases compiler may take care of this. But adding unnecessary
'goto' statements wouldn't make anything better. Code becomes less readable
actually.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
In power_supply_show_property() routine, we call ->get_property() conditionally
and should check for failure in that case only. There is no point comparing
'ret' for errors when 'ret' is surely zero.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
At multiple places we are doing exactly what PTR_ERR_OR_ZERO() does. And so that
routine can be reused instead of increasing lines of code here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The 'if' statements in power_supply_changed_work() are mostly there for taking
care of races and normally they will always evaluate to true. Optimize them for
fast execution with 'likely' statements.
Also there is need to have better comments in code to mention about the races
clearly. Get them in place.
Cc: Zoran Markovic <zrn.markovic@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
There is no need to check the value of ret.intval before returning it, as we
will be returning zero explicitly when ret.intval is zero.
So essentially we will end up returning value of ret.intval as it is. Drop the
unnecessary 'if' statements.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
We need to stop 'class_for_each_device' loop when a supply matches with the
of-node. In order to achieve this we currently return -EINVAL from
__power_supply_populate_supplied_from() on successful match.
class_for_each_device() is free to return similar errors in other cases as well
and so the choice of return value here isn't particularly great.
This commit isn't removing the Hack but making it more elegant by returning '1'
instead.
Also power_supply_find_supply_from_node() can return errors other than
-EPROBE_DEFER now if class_for_each_device() fails.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Callers of power_supply_find_supply_from_node(), i.e.
power_supply_check_supplies(), must propagate the errors returned by it instead
of returning their own.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
of_node_put() was called twice in power_supply_check_supplies() whereas a single
call will also work. Rearrange code a bit to make that feasible.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
In few routines, we need to end the do-while loop when no more "power-supplies"
are available. Currently we are doing 'continue' which will make the
'while(np)' conditional statement run again.
Skip this by doing a 'break' instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Typecast from 'void *' to any other pointer type falls under implicit typecasts
category and so doesn't require explicit typecasts. Drop them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
If power-supply's DT node doesn't have a valid "power-supplies" entry, then
power_supply_check_supplies() should return early instead of trying to allocate
memory for "supplied_from" array.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
In routine power_supply_check_supplies(), 'cnt' is counting the number of
supplies passed in "power-supplies" field of a node. The value of 'cnt' will
always be one more than the number of supplies after the do-while loop ends. And
so we need to allocate memory for 'cnt - 1' char pointers. But we are allocating
memory for 'cnt' instead.
Fix this by not over-allocating memory.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Usually PMIC's come with coulomb counting mechanism which can be
used to implement a Fuel Gauginig solution in Software itself.
One of key input to these SW Fuel Gauge solutioons is the boot up
parameters like boot voltage and boot current.
This patch adds the VOLTAGE_BOOT and CURRENT_BOOT power supply attributes
to report bootup voltage and current.
This patch also adds CALIBRATE power supply attribute which useful is
for calibrating the battery/coulomb counter.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch check the charging state after completed initialization of charger-
manager and update current charging state. If charger-manager never check and
update current charging state, charger-manager would have the mismatch issue
between real state of cable connection and the charging state of charger-manager
until first polling time of charger-manager.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch fix minor issue about checking wrong return type.
The of_cm_parse_desc() return ERR_PTR(errnor number) when some error happen
in this function. But, charger_manager_probe() has only checked whether
desc is NULL or not. If of_cm_parse_desc() returns ERR_PTR(-ENOMEM), desc
isn't NULL but desc is (void *)(-ENOMEM). Althouhg some error happen for parsing
DT, charger_manager_probe() can't detect error of desc instance.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The xgene-reset driver uses xgene_restart() as arm_pm_restart() but that
function should take an enum reset_type as the first argument rather than
a char. Fix this; the paramter is not referenced in the implementation.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
sbs-battery has a max design voltage but not a min design voltage field.
The SBS spec only has one design voltage:
http://www.sbs-forum.org/specs/sbdat110.pdf
Currently this is being used for max design voltage. This patch uses it
for min design voltage as well.
Signed-off-by: Simon Que <sque@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This CL supports two power_supply_property items for smart battery:
POWER_SUPPLY_PROP_MANUFACTURER and POWER_SUPPLY_PROP_MODEL_NAME such
that battery information 'manufacturer' and 'model_name' can be exported
to sysfs.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The wakeup status is read from Shutdown Status Register and not the
SHDW_CR which is the one at address 0.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
MACH_AT91 doesn't exist so we can't "depend" on it. Fix the typo
by using the proper ARCH_AT91 config option.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This tag holds the various new drivers introduced to move code that used to be
in mach-at91 over to the proper frameworks.
These files are the reboot and poweroff code for all AT91 SoCs but the RM9200,
and the ram controller driver is not doing much at the time, except for grabing
the RAM clock in order to leave it always enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTx4LlAAoJEBx+YmzsjxAggooP/0xIMF568hWNLWMOBLNyeXLP
SJUCBZw1kLqhw8K3nPV5GAmfGxgCCZ3uvUfMdIgJzSN+NtcuvQR2+ui2Bj1nzRRQ
y6ZAmoHEJHveNd3SoLpuE5s4KFwTBFblcBXHVSwIZzMcCioBxFWtcPupkIVoqt/z
s/gN5w9BsSCvqjtmYSTp8XTza9y7hx9Pmdpc1uzkP/WJbXtxyQX50NlpILQ1r7WW
WNOMRXOpv/JH+EHFtS7vMMvn+fQ94RVI209+Z2wez13H87C8MZF4N972vRHkmBuG
Uv2ZowFRo8T0YjJZfmyfWyg3C9fMOcQeOURAGO/FIavf0WJ+7/hmdZ9jymTpaA3b
WwZ+qgajMMdOk2ojW36vfueOqeuXx7bxGKWocXO/Rk00ZpN8Y2qFqmsJL5WNYVoN
SDod+nzYHA4ShyZFDiXoAf3R/+gjb9RvCJ0ZvjkdHUeU8GYHhXjDLPp1Ng7oDBut
szDE8FfWGpb5UsjFSdKfSsU2Xp3lqZ6fv89qiGYGwz7OqKRz2E0d8zm/EHoD87RR
jx9e4pWvk++Vouk/zCRZVb+HrGtN9FbZKfRq6xx1pAO+V2NCmq8ttcPH2BuN1K3T
quFRb6YBTfNfgVKPjbPsQ4QOuCR4juIZSubRhQEi7/Uie5aR/9q6Lz/pYbzitYjJ
qHR5nj7sL/WwJlfgFgbi
=YBPz
-----END PGP SIGNATURE-----
Merge tag 'at91-drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux
Pull AT91 reset, poweroff and ram drivers from Maxime Ripard:
"This tag holds the various new drivers introduced to move code that used to be
in mach-at91 over to the proper frameworks.
These files are the reboot and poweroff code for all AT91 SoCs but the RM9200,
and the ram controller driver is not doing much at the time, except for grabing
the RAM clock in order to leave it always enabled."
Conflicts:
arch/arm/mach-at91/Kconfig
This is the bulk of new SoC enablement and other platform changes for 3.17:
* Samsung S5PV210 has been converted to DT and multiplatform
* Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms
* Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood.
* Hwmod data for TI AM43xx and DRA7 platforms.
* More additions of Renesas shmobile platform support
* Removal of plat-samsung contents that can be removed with S5PV210 being
multiplatform/DT-enabled and the other two old platforms being removed.
New platforms (most with only basic support right now):
* Hisilicon X5HD2 settop box chipset is introduced
* Mediatek MT6589 (mobile chipset) is introduced
* Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=5TJ6
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This is the bulk of new SoC enablement and other platform changes for
3.17:
- Samsung S5PV210 has been converted to DT and multiplatform
- Clock drivers and bindings for some of the lower-end i.MX 1/2
platforms
- Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood
- Hwmod data for TI AM43xx and DRA7 platforms
- More additions of Renesas shmobile platform support
- Removal of plat-samsung contents that can be removed with S5PV210
being multiplatform/DT-enabled and the other two old platforms
being removed
New platforms (most with only basic support right now):
- Hisilicon X5HD2 settop box chipset is introduced
- Mediatek MT6589 (mobile chipset) is introduced
- Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code"
* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
ARM: hisi: remove smp from machine descriptor
power: reset: move hisilicon reboot code
ARM: dts: Add hix5hd2-dkb dts file.
ARM: debug: Rename Hi3716 to HIX5HD2
ARM: hisi: enable hix5hd2 SoC
ARM: hisi: add ARCH_HISI
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Documentation: arm: misc updates to Marvell EBU SoC status
Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
ARM: mvebu: fix build without platforms selected
ARM: mvebu: add cpuidle support for Armada 38x
ARM: mvebu: add cpuidle support for Armada 370
cpuidle: mvebu: add Armada 38x support
cpuidle: mvebu: add Armada 370 support
cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
ARM: mvebu: export the SCU address
...
Fixes the following sparse warnings:
drivers/power/ipaq_micro_battery.c:278:24: warning:
symbol 'micro_batt_device_driver' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This adds a driver for reading the battery status of the
battery connected to the Atmel microcontroller on the
iPAQ h3xxx series.
Based on a driver from handhelds.org 2.6.21 kernel, written
by Alessandro GARDICH.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
TWL4030's Battery Charger seems to be designed for non-hotpluggable
batteries.
If battery is not present in the system, BATSTS is always set with the
expectation that software will take actions to move to a required safe
state (could be power down or disable various charger paths).
It does not seem possible even by manipulating the edge detection
of the event (using BCIEDR2 register) to have a consistent hotplug
handling. This seems to be the result of BATSTS interrupt generated
when the thermistor of the battery pack is disconnected from the
dedicated ADIN1 pin. Clearing the status just results in the status
being regenerated by the monitoring ADC(MADC) and disabling the
edges of event just makes hotplug no longer function. The only
other option is to disable the detection of the MADC by disabling
BCIMFEN4::BATSTSMCHGEN (battery presence detector) - but then, we can
never again detect battery reconnection.
So, detect battery presence based on precharge(which is hardware
automatic state) or default main charger configuration at the time of
probe and enable charger logic only if battery was present.
Reported-by: Russell King <linux@arm.linux.org.uk>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add support for reboot functionality on boards with ARM-based
Broadcom STB chipsets. Make it built-in by default for ARCH_BRCMSTB,
but allow it to be configurable under COMPILE_TEST.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fixes the following sparse warnings:
drivers/power/power_supply_core.c:540:5: warning:
symbol '__power_supply_register' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add new power supply properties for input current, charge termination
current, min and max temperature
POWER_SUPPLY_PROP_TEMP_MIN - minimum operatable temperature
POWER_SUPPLY_PROP_TEMP_MAX - maximum operatable temperature
POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT - input current limit programmed
by charger. Indicates the input current for a charging source.
POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT - Charge termination current used
to detect the end of charge condition
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
On the ARM Chromebook tps65090 has two masters: the AP (the main
processor running linux) and the EC (the embedded controller). The AP
is allowed to mess with FETs but the EC is in charge of charge control.
The tps65090 interupt line is routed to both the AP and the EC, which
can cause quite a headache. Having two people adjusting masks and
acking interrupts is a recipe for disaster.
In the shipping kernel we had a hack to have the AP pay attention to
the IRQ but not to ack it. It also wasn't supposed to configure the
IRQ in any way. That hack allowed us to detect when the device was
charging without messing with the EC's state.
The current tps65090 infrastructure makes the above difficult, and it
was a bit of a hack to begin with. Rather than uglify the driver to
support it, just extend the driver's existing notion of "no irq" to
the charger. This makes the charger code poll every 2 seconds for AC
detect, which is sufficient.
For proper functioning, requires (mfd: tps65090: Don't tell child
devices we have an IRQ if we don't). If we don't have that patch
we'll simply fail to probe on devices without an interrupt (just like
we did before this patch).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
[sre@kernel.org: Use -ENXIO instead of NO_IRQ for missing interrupt,
since NO_IRQ is not available on all architectures.]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Per license_is_gpl_compatible(), the MODULE_LICENSE() string for GPL v2 is
"GPL v2", not "GPLv2". Use "GPL v2" so this module doesn't taint the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This switches the GPIO poweroff driver to use GPIO descriptors
rather than numeral GPIOs. We get rid of the specific inversion
handling as GPIO descriptors know if they are active low or
high and can assert the line properly, so we do not need to
check the flag OF_GPIO_ACTIVE_LOW returned from the old call
of_get_gpio_flags() anymore.
Also convert to use managed resources and use dev_* message
printing while we're at it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
One an hdq buss, a missing device reads as 0xff, not -1.
So do a translation to allow detecting of a missing bus.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions for both platform and i2c drivers. Also, the unecessary
variable ret and labels batt_failed3, err_free were removed.
The following Coccinele script was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add a driver to handle the shutdown of the Atmel SoCs. This code used to be
(and still is) in arch/arm/mach-at91. We didn't remove it yet so that we can
convert all the boards to using this driver, before removing it entirely in a
separate patch.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Implement the reset behaviour of the various AT91 SoCS in drivers/power/reset.
It used to be (and still is) located in arch/arm/mach-at91, and in order to
preserve bisectability is not removed yet, but every board should be converted
to use this driver instead.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
All the config option so far are depending on the POWER_RESET symbol
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
- ACPICA update to upstream version 20140424. That includes a
number of fixes and improvements related to things like GPE
handling, table loading, headers, memory mapping and unmapping,
DSDT/SSDT overriding, and the Unload() operator. The acpidump
utility from upstream ACPICA is included too. From Bob Moore,
Lv Zheng, David Box, David Binderman, and Colin Ian King.
- Fixes and cleanups related to ACPI video and backlight interfaces
from Hans de Goede. That includes blacklist entries for some new
machines and using native backlight by default.
- ACPI device enumeration changes to create platform devices
rather than PNP devices for ACPI device objects with _HID by
default. PNP devices will still be created for the ACPI device
object with device IDs corresponding to real PNP devices, so
that change should not break things left and right, and we're
expecting to see more and more ACPI-enumerated platform devices
in the future. From Zhang Rui and Rafael J Wysocki.
- Updates for the ACPI LPSS (Low-Power Subsystem) driver allowing
it to handle system suspend/resume on Asus T100 correctly.
From Heikki Krogerus and Rafael J Wysocki.
- PM core update introducing a mechanism to allow runtime-suspended
devices to stay suspended over system suspend/resume transitions
if certain additional conditions related to coordination within
device hierarchy are met. Related PM documentation update and
ACPI PM domain support for the new feature. From Rafael J Wysocki.
- Fixes and improvements related to the "freeze" sleep state. They
affect several places including cpuidle, PM core, ACPI core, and
the ACPI battery driver. From Rafael J Wysocki and Zhang Rui.
- Miscellaneous fixes and updates of the ACPI core from Aaron Lu,
Bjørn Mork, Hanjun Guo, Lan Tianyu, and Rafael J Wysocki.
- Fixes and cleanups for the ACPI processor and ACPI PAD (Processor
Aggregator Device) drivers from Baoquan He, Manuel Schölling,
Tony Camuso, and Toshi Kani.
- System suspend/resume optimization in the ACPI battery driver from
Lan Tianyu.
- OPP (Operating Performance Points) subsystem updates from
Chander Kashyap, Mark Brown, and Nishanth Menon.
- cpufreq core fixes, updates and cleanups from Srivatsa S Bhat,
Stratos Karafotis, and Viresh Kumar.
- Updates, fixes and cleanups for the Tegra, powernow-k8, imx6q,
s5pv210, nforce2, and powernv cpufreq drivers from Brian Norris,
Jingoo Han, Paul Bolle, Philipp Zabel, Stratos Karafotis, and
Viresh Kumar.
- intel_pstate driver fixes and cleanups from Dirk Brandewie,
Doug Smythies, and Stratos Karafotis.
- Enabling the big.LITTLE cpufreq driver on arm64 from Mark Brown.
- Fix for the cpuidle menu governor from Chander Kashyap.
- New ARM clps711x cpuidle driver from Alexander Shiyan.
- Hibernate core fixes and cleanups from Chen Gang, Dan Carpenter,
Fabian Frederick, Pali Rohár, and Sebastian Capella.
- Intel RAPL (Running Average Power Limit) driver updates from
Jacob Pan.
- PNP subsystem updates from Bjorn Helgaas and Fabian Frederick.
- devfreq core updates from Chanwoo Choi and Paul Bolle.
- devfreq updates for exynos4 and exynos5 from Chanwoo Choi and
Bartlomiej Zolnierkiewicz.
- turbostat tool fix from Jean Delvare.
- cpupower tool updates from Prarit Bhargava, Ramkumar Ramachandra
and Thomas Renninger.
- New ACPI ec_access.c tool for poking at the EC in a safe way
from Thomas Renninger.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=tpdF
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm into next
Pull ACPI and power management updates from Rafael Wysocki:
"ACPICA is the leader this time (63 commits), followed by cpufreq (28
commits), devfreq (15 commits), system suspend/hibernation (12
commits), ACPI video and ACPI device enumeration (10 commits each).
We have no major new features this time, but there are a few
significant changes of how things work. The most visible one will
probably be that we are now going to create platform devices rather
than PNP devices by default for ACPI device objects with _HID. That
was long overdue and will be really necessary to be able to use the
same drivers for the same hardware blocks on ACPI and DT-based systems
going forward. We're not expecting fallout from this one (as usual),
but it's something to watch nevertheless.
The second change having a chance to be visible is that ACPI video
will now default to using native backlight rather than the ACPI
backlight interface which should generally help systems with broken
Win8 BIOSes. We're hoping that all problems with the native backlight
handling that we had previously have been addressed and we are in a
good enough shape to flip the default, but this change should be easy
enough to revert if need be.
In addition to that, the system suspend core has a new mechanism to
allow runtime-suspended devices to stay suspended throughout system
suspend/resume transitions if some extra conditions are met
(generally, they are related to coordination within device hierarchy).
However, enabling this feature requires cooperation from the bus type
layer and for now it has only been implemented for the ACPI PM domain
(used by ACPI-enumerated platform devices mostly today).
Also, the acpidump utility that was previously shipped as a separate
tool will now be provided by the upstream ACPICA along with the rest
of ACPICA code, which will allow it to be more up to date and better
supported, and we have one new cpuidle driver (ARM clps711x).
The rest is improvements related to certain specific use cases,
cleanups and fixes all over the place.
Specifics:
- ACPICA update to upstream version 20140424. That includes a number
of fixes and improvements related to things like GPE handling,
table loading, headers, memory mapping and unmapping, DSDT/SSDT
overriding, and the Unload() operator. The acpidump utility from
upstream ACPICA is included too. From Bob Moore, Lv Zheng, David
Box, David Binderman, and Colin Ian King.
- Fixes and cleanups related to ACPI video and backlight interfaces
from Hans de Goede. That includes blacklist entries for some new
machines and using native backlight by default.
- ACPI device enumeration changes to create platform devices rather
than PNP devices for ACPI device objects with _HID by default. PNP
devices will still be created for the ACPI device object with
device IDs corresponding to real PNP devices, so that change should
not break things left and right, and we're expecting to see more
and more ACPI-enumerated platform devices in the future. From
Zhang Rui and Rafael J Wysocki.
- Updates for the ACPI LPSS (Low-Power Subsystem) driver allowing it
to handle system suspend/resume on Asus T100 correctly. From
Heikki Krogerus and Rafael J Wysocki.
- PM core update introducing a mechanism to allow runtime-suspended
devices to stay suspended over system suspend/resume transitions if
certain additional conditions related to coordination within device
hierarchy are met. Related PM documentation update and ACPI PM
domain support for the new feature. From Rafael J Wysocki.
- Fixes and improvements related to the "freeze" sleep state. They
affect several places including cpuidle, PM core, ACPI core, and
the ACPI battery driver. From Rafael J Wysocki and Zhang Rui.
- Miscellaneous fixes and updates of the ACPI core from Aaron Lu,
Bjørn Mork, Hanjun Guo, Lan Tianyu, and Rafael J Wysocki.
- Fixes and cleanups for the ACPI processor and ACPI PAD (Processor
Aggregator Device) drivers from Baoquan He, Manuel Schölling, Tony
Camuso, and Toshi Kani.
- System suspend/resume optimization in the ACPI battery driver from
Lan Tianyu.
- OPP (Operating Performance Points) subsystem updates from Chander
Kashyap, Mark Brown, and Nishanth Menon.
- cpufreq core fixes, updates and cleanups from Srivatsa S Bhat,
Stratos Karafotis, and Viresh Kumar.
- Updates, fixes and cleanups for the Tegra, powernow-k8, imx6q,
s5pv210, nforce2, and powernv cpufreq drivers from Brian Norris,
Jingoo Han, Paul Bolle, Philipp Zabel, Stratos Karafotis, and
Viresh Kumar.
- intel_pstate driver fixes and cleanups from Dirk Brandewie, Doug
Smythies, and Stratos Karafotis.
- Enabling the big.LITTLE cpufreq driver on arm64 from Mark Brown.
- Fix for the cpuidle menu governor from Chander Kashyap.
- New ARM clps711x cpuidle driver from Alexander Shiyan.
- Hibernate core fixes and cleanups from Chen Gang, Dan Carpenter,
Fabian Frederick, Pali Rohár, and Sebastian Capella.
- Intel RAPL (Running Average Power Limit) driver updates from Jacob
Pan.
- PNP subsystem updates from Bjorn Helgaas and Fabian Frederick.
- devfreq core updates from Chanwoo Choi and Paul Bolle.
- devfreq updates for exynos4 and exynos5 from Chanwoo Choi and
Bartlomiej Zolnierkiewicz.
- turbostat tool fix from Jean Delvare.
- cpupower tool updates from Prarit Bhargava, Ramkumar Ramachandra
and Thomas Renninger.
- New ACPI ec_access.c tool for poking at the EC in a safe way from
Thomas Renninger"
* tag 'pm+acpi-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (187 commits)
ACPICA: Namespace: Remove _PRP method support.
intel_pstate: Improve initial busy calculation
intel_pstate: add sample time scaling
intel_pstate: Correct rounding in busy calculation
intel_pstate: Remove C0 tracking
PM / hibernate: fixed typo in comment
ACPI: Fix x86 regression related to early mapping size limitation
ACPICA: Tables: Add mechanism to control early table checksum verification.
ACPI / scan: use platform bus type by default for _HID enumeration
ACPI / scan: always register ACPI LPSS scan handler
ACPI / scan: always register memory hotplug scan handler
ACPI / scan: always register container scan handler
ACPI / scan: Change the meaning of missing .attach() in scan handlers
ACPI / scan: introduce platform_id device PNP type flag
ACPI / scan: drop unsupported serial IDs from PNP ACPI scan handler ID list
ACPI / scan: drop IDs that do not comply with the ACPI PNP ID rule
ACPI / PNP: use device ID list for PNPACPI device enumeration
ACPI / scan: .match() callback for ACPI scan handlers
ACPI / battery: wakeup the system only when necessary
power_supply: allow power supply devices registered w/o wakeup source
...
The bulk of the changes for this release are a few new drivers however
there are a couple of noticable core changes and the usual stream of
cleanups and fixes:
- Move disable of unused regulators later in init so it comes after
deferred probe has iterated making startup smoother.
- Fixes reference counting of the DT nodes for constraints from Charles
Keepax. This has little practical impact since all real users of
the regulator bindings use FDT which doesn't need the reference
counting.
- Lots of cleanups, especially to the Samsung drivers.
- Support for Linear Technologies LTC3589, Texas Instruments TPS658640
and X-Powers AXP20x.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTjaRuAAoJELSic+t+oim96AAP/jNtqLoBLIz6Idwg29Jd3Gj+
X3R+5NfuS0kccvKvIbHmKygwJ6hY9anBsKQ28AH6VUAgcUqrPnWiRyl4iZAyMSQZ
bweQ1QSAIxjAD9J+hMSMU65h3pKh7t6k20dumEUOJZ/ZuPmYj5aks3dy+DKSIkF2
GDG1SVonxheuhUbxEPnXlz5pSnFtERQQMGPdYzk3RxqdeDeVr6Oanlxuo/IKagPP
vm6BFFutEcSk4KpkEQF+iGxIDTzTFGjMe2TzDu1ubxsxcL+5sNh8rkN9rbqQ0fdo
fGMZuo9AXEPXNDwY6ug0Mxoqhg0vrf8NSnEWjM6zQJELKH6H4KMhwAGjstCDkFer
rsuZXeIM1Mk1wrPP6QWLvHVqwS9GUXki82ZgUpDOn61HpRLUu6bKY8eWoq3UM79S
qiRoNSW7eggI0/71IrzumWWE8HEufEJEgGNAqwFPkBywCg+biXjkHlcXdyBMCpqy
kUev0QVJb3FHBnyIdMAVm8hrreejh+frl2Nc+aIEhYZxc3idvVqKl1lvjbObt6PM
FK52n8c/WlQxLZ8+isv0b1+pwT6QHeLzBvBA8mE6+Mn4vLzQKT4nofQU4PSASRSM
UqkaSMhaaJ4WRXlNdhkp721EbRAltrTwzjMS/7lTTZRyN9g9ODOhDnzRT2f3J8F1
JYS22jFTL5ywNR6GFcq0
=JrfM
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into next
Pull regulator updates from Mark Brown:
"The bulk of the changes for this release are a few new drivers however
there are a couple of noticable core changes and the usual stream of
cleanups and fixes:
- move disable of unused regulators later in init so it comes after
deferred probe has iterated making startup smoother.
- fixes to reference counting of the DT nodes for constraints from
Charles Keepax. This has little practical impact since all real
users of the regulator bindings use FDT which doesn't need the
reference counting.
- lots of cleanups, especially to the Samsung drivers.
- support for Linear Technologies LTC3589, Texas Instruments
TPS658640 and X-Powers AXP20x"
* tag 'regulator-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (64 commits)
regulator: pbias: remove unnecessary OOM messages
regulator: max8649: remove unnecessary OOM messages
regulator: core: Fix the init of DT defined fixed regulators
regulator: core: Disable unused regulators after deferred probing is done
regulator: Don't disable unused regulators we don't have permission for
regulator: axp20x: Use regulator_map_voltage_ascend for LDO4
regulator: use of_property_read_{bool|u32}()
regulator: Fix regulator_get_{optional,exclusive}() documentation
regulators: Add definition of regulator_set_voltage_time() for !CONFIG_REGULATOR
regulator: arizona-ldo1: add missing #include
regulator: pfuze100: Support enable/disable for fixed regulator
regulator: ltc3589: Remove ltc3589_list_voltage_fixed function
regulator: ltc3589: Fix module dependency
regulator: tps6586x: Remove unused to_tps6586x_dev() function
regulator: tps65218: Convert to use regulator_set_voltage_time_sel
regulator: tps6586x: Add support for the TPS658640
regulator: tps6586x: Prepare supporting fixed regulators
regulator: pfuze100: Don't allocate an invalid gpio
regulator: pfuze100: Support SWB enable/disable
regulator: fixed: use of_property_read_{bool|u32}()
...
SoC-near driver changes that we're merging through our tree. Mostly
because they depend on other changes we have staged, but in some cases
because the driver maintainers preferred that we did it this way.
This contains a largeish cleanup series of the omap_l3_noc bus driver,
cpuidle rework for Exynos, some reset driver conversions and a long
branch of TI EDMA fixes and cleanups, with more to come next release.
The TI EDMA cleanups is a shared branch with the dmaengine tree, with
a handful of Davinci-specific fixes on top.
After discussion at last year's KS (and some more on the mailing lists),
we are here adding a drivers/soc directory. The purpose of this is
to keep per-vendor shared code that's needed by different drivers but
that doesn't fit into the MFD (nor drivers/platform) model. We expect
to keep merging contents for this hierarchy through arm-soc so we can
keep an eye on what the vendors keep adding here and not making it a
free-for-all to shove in crazy stuff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=SC+e
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC driver changes from Olof Johansson:
"SoC-near driver changes that we're merging through our tree. Mostly
because they depend on other changes we have staged, but in some cases
because the driver maintainers preferred that we did it this way.
This contains a largeish cleanup series of the omap_l3_noc bus driver,
cpuidle rework for Exynos, some reset driver conversions and a long
branch of TI EDMA fixes and cleanups, with more to come next release.
The TI EDMA cleanups is a shared branch with the dmaengine tree, with
a handful of Davinci-specific fixes on top.
After discussion at last year's KS (and some more on the mailing
lists), we are here adding a drivers/soc directory. The purpose of
this is to keep per-vendor shared code that's needed by different
drivers but that doesn't fit into the MFD (nor drivers/platform)
model. We expect to keep merging contents for this hierarchy through
arm-soc so we can keep an eye on what the vendors keep adding here and
not making it a free-for-all to shove in crazy stuff"
* tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
cpufreq: exynos: Fix driver compilation with ARCH_MULTIPLATFORM
tty: serial: msm: Remove direct access to GSBI
power: reset: keystone-reset: introduce keystone reset driver
Documentation: dt: add bindings for keystone pll control controller
Documentation: dt: add bindings for keystone reset driver
soc: qcom: fix of_device_id table
ARM: EXYNOS: Fix kernel panic when unplugging CPU1 on exynos
ARM: EXYNOS: Move the driver to drivers/cpuidle directory
ARM: EXYNOS: Cleanup all unneeded headers from cpuidle.c
ARM: EXYNOS: Pass the AFTR callback to the platform_data
ARM: EXYNOS: Move S5P_CHECK_SLEEP into pm.c
ARM: EXYNOS: Move the power sequence call in the cpu_pm notifier
ARM: EXYNOS: Move the AFTR state function into pm.c
ARM: EXYNOS: Encapsulate the AFTR code into a function
ARM: EXYNOS: Disable cpuidle for exynos5440
ARM: EXYNOS: Encapsulate boot vector code into a function for cpuidle
ARM: EXYNOS: Pass wakeup mask parameter to function for cpuidle
ARM: EXYNOS: Remove ifdef for scu_enable in pm
ARM: EXYNOS: Move scu_enable in the cpu_pm notifier
ARM: EXYNOS: Use the cpu_pm notifier for pm
...
A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support for
big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation and
moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as most
of the other v7 platforms in the tree. \o/ The work isn't quite complete,
there's some driver fixes still needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
Plus a large set of various smaller updates for different platforms. I'm
probably missing some important one here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTjOKWAAoJEIwa5zzehBx36aEP/2vTD7x9FC59FACNHJ8iO7aw
0ebTgBBjI1Np6X18O+M7URbxV5TaBgwpUm/NDN86p03MpQ2eOXr8r47qVxe/HhZs
AdlTvzgE6QwxcVL/HeCKKUEN3BPH74+TZgFl9I5aSzNjpR39xETeK1aWP/ZiAl/q
/lGRZAQ59+c7Ung00Hg0g2YDxH9WFpK50Nj90ROnyjKSFkhIYngXYVpZB3maOypq
Pgib/U8IraKZ52oGJw3yinSoORr7FdcUdAGWGTz/lQdNL/jYDfQ6GkRW2oblWXdt
3Xvj9UW6NmkbMICucMvFuuW1nXAgutZuTp9w7mBxsiUlYepxPv/DXM6yiI1WGlEb
BeVOmOreNeN2nT6avv/uUhk3Osq63Jn9x8cz5y+7/lgWQwllh3/c+G01RotvgJEQ
vpQq5ps9fMxIAMaNP6N/YqMJI1IOrBj0iXxaZEDw3VYM/k4lSvtb3VXP9c/rqApu
U4i6hpSIGzrraU4NrjndYPndcLeNOVZbByETQKosZXuCo6G1sb7FstNSkzI9vSo8
O/pujIVUfYyBW82GzZGDw+aa7DWA29FPeUQ3p+sj5MSCg051xXT8h6QwqMo2K/zY
5ATs/qo6w7zH/Ou9rtHTRynCIb0GQJThDSlWtuXFedUF9quEltS+TDz/2o+dWtGJ
yBFGKDRuBB20D36w9xqg
=6LYI
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
Currently, all the power supply devices are registered with wakeup source,
this results in that every power_supply_changed() invocation brings
the system out of suspend-to-freeze state.
This is overkill as some device drivers, e.g. ACPI battery driver,
have the ability to check the device status and wake up the system
from sleeping only when necessary.
Thus introduce a new API which allows device to be registered
w/o wakeup source.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
