The Uartlite data sheet defines the registers as 32 bit wide. This
patch changes the register access to use 32 bit transfers and eliminates
the magic +3 offset which is currently required to make the device
work.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: John Williams <jwilliams@itee.uq.edu.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Adds support for generic Xilinx Virtex boards. Any board which specifies
"xilinx,virtex" in the compatible property will make use of this board
support.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Adds support for the Xilinx opb-intc interrupt controller
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add the needed kconfig macros to enable Xilinx Virtex board support
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Allows the bootwrapper to use the uartlite device for console output.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add a workaround for PowerPC 440EPx/GRx incorrect write to
DDR SDRAM errata. Data can be written to wrong address
in SDRAM when write pipelining enabled on plb0. We disable
it in the cpu_setup for these processors at early init.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The PowerPC 440EP(x) FPU init is currently done in head_44x
under ifdefs. Since we should support more then one board
in the same kernel, we move FPU initialization code from head_44x
to cpu_setup_44x and add cpu_setup callbacks for 440EP(x).
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds cpu_setup functionality for ppc44x platform.
Low level cpu-spefic initialization routines should be
placed in cpu_setup_44x.S and a callback should be
added to cputable. The cpu_setup is invoked
by identify_cpu() function at early init.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Pass the appropriate -mcpu flag to the treeboot-walnut.o object to prevent
some toolchains from erroring out with unknown opcodes
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This registers a clock event structure for the decrementer and turns
on CONFIG_GENERIC_CLOCKEVENTS, which means that we now don't need
most of timer_interrupt(), since the work is done in generic code.
For secondary CPUs, their decrementer clockevent is registered when
the CPU comes up (the generic code automatically removes the
clockevent when the CPU goes down).
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some older pSeries machines were panicking in pSeries_log_error
because it was getting called before it was ready. This is a result
of commit "[POWERPC] pseries: Fix jumbled no_logging flag."
(79c0108d1b).
This fixes it by explicitly enabling RTAS error logging when it has
been initialized, and also makes the code clearer by renaming the
"no_more_logging" variable to "logging_enabled".
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use alloc_maybe_bootmem() which wraps the if (mem_init_done)
malloc clause.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds support for the PCI bus on Celleb with new "I/O routines
for PowerPC." External PCI on Celleb must do explicit synchronization
with devices (Bus has no automatic synchronization feature).
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is an update for Serial I/O on Celleb.
- Detection algorithm has been changed
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the Celleb code to work with new Guest OS Interface
to tweak HTAB on Beat. It detects old and new Guest OS Interfaces
automatically.
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This supports Power/Reset buttons on Beat on Celleb.
On Beat, we have an event from Beat if Power button or Reset button
is pressed. This patch catches the event and convert it to a signal
to INIT process by calling ctrl_alt_del() function.
/sbin/inittab have no entry to turn the machine power off so we have
to detect if power button is pressed or not internally in our driver.
This idea is taken from PS3's event handling subsystem.
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is an update for "Beat on Celleb"
- Move beat_pause(), beat_kexec_cpu_down() from setup.c to beat.c
Signed-off-by: <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that dcr_host_t contains the base address, we can use that in the
axon_msi code, rather than storing it separately.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that dcr_host_t contains the base address, we can use that in the mpic
code, rather than storing it separately.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In its current form, dcr_map() doesn't remember the base address you passed
it, which means you need to store it somewhere else. Rather than adding the
base to another struct it seems simpler to store it in the dcr_host_t.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The trick for finding the right defconfig is neat, but you forgot to
provide an i686_defconfig. ;-)
More seriously, cross compiling the defconfig is often useful, e.g. for
testing the compilation of patches that touch multiple architectures,
and this patch therefore chooses g5_defconfig if $(CROSS_COMPILE) is
non-empty.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This keeps an unstripped copy of the vDSO images built before they are
stripped and embedded in the kernel. The unstripped copies get installed in
$(MODLIB)/vdso/ by "make install". These files can be useful when they
contain source-level debugging information.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add CONFIG_DEBUG_PREEMPT support to ppc64: it was useful for testing
get_paca() preemption. Cheat a little, just use debug_smp_processor_id()
in the debug version of get_paca(): it contains all the right checks and
reporting, though get_paca() doesn't really use smp_processor_id().
Use local_paca for what might have been called __raw_get_paca().
Silence harmless warnings from io.h and lparcfg.c with local_paca -
it is okay for iseries_lparcfg_data to be referencing shared_proc
with preemption enabled: all cpus should show the same value for
shared_proc.
Why do other architectures need TRACE_IRQFLAGS_SUPPORT for DEBUG_PREEMPT?
I don't know, ppc64 appears to get along fine without it.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch introduces zalloc_maybe_bootmem and uses it so that we don't
have to mark a whole (largish) routine as __init_ref_ok.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On non-book-E, exceptions execute in real mode. If a fault happens
that leads to a register dump, the kernel currently prints XXXXXXXX
because it doesn't realize that PC is a physical address.
This patch checks whether instruction address translation is turned
on, and if not converts PC into a virtual address.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The /proc/bus/pci/* files list PCI domain numbers only for
devices that claim to be on a multi-domain system. The check
for this is broken on powerpc, because the buid value is
truncated to 32 bits.
There is at least one machine (IBM QS21) that only uses
the high-order bits of the buid, so the return value
of pci_proc_domain() ends up being always zero, which
makes /proc/bus/pci useless.
Change the logic to always return '1' for a nonzero
buid value.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This restores the CHECK_FULL_REGS sanity check to every place that can
access the nonvolatile GPRs for ptrace. This is already done for
native-bitwidth PTRACE_PEEKUSR, but was omitted for many other cases
(32-bit ptrace, PTRACE_GETREGS, etc.); I think there may have been more
uniform checks before that were lost in the recent cleanup of GETREGS et al.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a library that board code can use to extract information from the
PlanetCore configuration keys. PlanetCore is used on various boards from
Embedded Planet.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows callers to set addresses one at a time when that would be more
convenient.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Call gunzip_partial to calculate the remaining length and copy the
data to the user buffer. This makes it shorter and reduces
duplication.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Record the number of header bytes skipped in the total bytes read field.
This is needed for the initramfs parsing code to find the end of the zip file.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
iSeries_vio_dev was already statically initialised and we can remove
one set of #ifdef CONFIG_PPC_ISERIES guards.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With these functions implemented we cooperate better with the generic
timekeeping code. This obsoletes the need for the timer sysdev as a bonus.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The entries are only 32-bit, so restrict the virtual address to stay
below 0xffff_ffff. With KERNELBASE set to 0xc000_0000, this in effect
restricts access to the first 1GB of real memory.
Make setup_kcore conditional on CONFIG_PROC_KCORE for both 32/64.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently the prep_defconfig in arch/ppc won't build due to swsusp
being broken. This patch avoids the problem by essentially disabling
all power management on those platforms left in arch/ppc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Linus made this suggestion for the x86 merge and this starts the process
for powerpc. We assume that CONFIG_PPC64 implies CONFIG_PPC_MERGE and
CONFIG_PPC_STD_MMU_32 implies CONFIG_PPC_STD_MMU.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move out the old-style exception parsers to a separate function, and
don't call it on platforms that have a platform-specific handler.
It would make sense to move out the generic versions into their platforms
instead, but that can be done gradually down the road.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This provides an implementation of the <linux/clk.h> interface for
arch/powerpc using a set of function pointers in clk_functions.
Platforms that want to support this interface should fill
clk_functions and select CONFIG_PPC_CLOCK in Kconfig.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the MPIC U3 MSI code, we call u3msi_compose_msi_msg() once for each MSI.
This is overkill, as the address is per pci device, not per MSI. So setup
the address once, and just set the data per MSI.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently rtas_change_msi() returns either the error code from RTAS, or if
the RTAS call succeeded the number of irqs that were configured by RTAS.
This makes checking the return value more complicated than it needs to be.
Instead, have rtas_change_msi() check that the number of irqs configured by
RTAS is equal to what we requested - and return an error otherwise. This makes
the return semantics match the usual 0 for success, something else for error.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
rtas_setup_msi_irqs() doesn't need to call teardown() itself, the
generic code will do this for us as long as we return a non-zero
value.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
u3msi_setup_msi_irqs() doesn't need to call teardown() itself,
the generic code will do this for us as long as we return a non
zero value.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
pci_device_to_OF_node() returns the device node attached to a PCI device,
but doesn't actually grab a reference - we need to do it ourselves.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
