Clean up due to code review.
The nfs4_verifier's data field is not guaranteed to be u32-aligned.
Casting an array of chars to a u32 * is considered generally
hazardous.
Fix this by using a __be32 array to generate a verifier's contents,
and then byte-copy the contents into the verifier field. The contents
of a verifier, for all intents and purposes, are opaque bytes. Only
local code that generates a verifier need know the actual content and
format. Everyone else compares the full byte array for exact
equality.
Also, sizeof(nfs4_verifer) is the size of the in-core verifier data
structure, but NFS4_VERIFIER_SIZE is the number of octets in an XDR'd
verifier. The two are not interchangeable, even if they happen to
have the same value.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Replace the union with the common struct stateid4 as defined in both
RFC3530 and RFC5661. This makes it easier to access the sequence id,
which will again make implementing support for parallel OPEN calls
easier.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
It is really a function for selecting the correct stateid to use in a
read or write situation.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The current version of encode_stateid really only applies to open stateids.
You can't use it for locks, delegations or layouts.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Change the name to reflect what we're really doing: testing two
stateids for whether or not they match according the the rules in
RFC3530 and RFC5661.
Move the code from callback_proc.c to nfs4proc.c
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
nfs41_validate_delegation_stateid is broken if we supply a stateid with
a non-zero sequence id. Instead of trying to match the sequence id,
the function assumes that we always want to error. While this is
true for a delegation callback, it is not true in general.
Also fix a typo in nfs4_callback_recall.
Reported-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If we know that the delegation stateid is bad or revoked, we need to
remove that delegation as soon as possible, and then mark all the
stateids that relied on that delegation for recovery. We cannot use
the delegation as part of the recovery process.
Also note that NFSv4.1 uses a different error code (NFS4ERR_DELEG_REVOKED)
to indicate that the delegation was revoked.
Finally, ensure that setlk() and setattr() can both recover safely from
a revoked delegation.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
The check for 'fh == NULL' needs to come _before_ we dereference
fh.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The attempt to display the implementation ID needs to be conditional on
whether or not CONFIG_NFS_V4_1 is defined
Reported-by: Bryan Schumaker <Bryan.Schumaker@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Conflicts:
fs/nfs/nfs4proc.c
Back-merge of the upstream kernel in order to fix a conflict with the
slotid type conversion and implementation id patches...
Get rid of
encode_compound: tag=
when XDR debugging is enabled. The current Linux client never sets
compound tags.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The fh_expire_type file attribute is a filesystem wide attribute that
consists of flags that indicate what characteristics file handles
on this FSID have.
Our client doesn't support volatile file handles. It should find
out early (say, at mount time) whether the server is going to play
shenanighans with file handles during a migration.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The Linux NFS client must distinguish between referral events (which
it currently supports) and migration events (which it does not yet
support).
In both types of events, an fs_locations array is returned. But upper
layers, not the XDR layer, should make the distinction between a
referral and a migration. There really isn't a way for an XDR decoder
function to distinguish the two, in general.
Slightly adjust the FATTR flags returned by decode_fs_locations()
to set NFS_ATTR_FATTR_V4_LOCATIONS only if a non-empty locations
array was returned from the server. Then have logic in nfs4proc.c
distinguish whether the locations array is for a referral or
something else.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean up: pass just the clientid4 to encode_renew(). This enables it
to be used by callers who might not have an full nfs_client.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
For debugging, introduce a simplistic function to print NFS file
handles on the system console. The main function is hooked into the
dprintk debugging facility, but you can directly call the helper,
_nfs_display_fhandle(), if you want to print a handle unconditionally.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
For NFSv4 mounts, the clientaddr= mount option has always been
required. Now we have rpc_localaddr() in the kernel, which was
modeled after the same logic in the mount.nfs command that constructs
the clientaddr= mount option. If user space doesn't provide a
clientaddr= mount option, the kernel can now construct its own.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When the cl_xprt field is updated, the cl_server field will also have
to change. Since the contents of cl_server follow the remote endpoint
of cl_xprt, just move that field to the rpc_xprt.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
[ cel: simplify check_gss_callback_principal(), whitespace changes ]
[ cel: forward ported to 3.4 ]
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
A migration event will replace the rpc_xprt used by an rpc_clnt. To
ensure this can be done safely, all references to cl_xprt must now use
a form of rcu_dereference().
Special care is taken with rpc_peeraddr2str(), which returns a pointer
to memory whose lifetime is the same as the rpc_xprt.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
[ cel: fix lockdep splats and layering violations ]
[ cel: forward ported to 3.4 ]
[ cel: remove rpc_max_reqs(), add rpc_net_ns() ]
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
CLOSE is new with NFSv4. Sometimes it's important to know the timing
of this operation compared to things like lease renewal.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
I noticed recently that decode_attr_fs_locations() is not generating
very pretty debugging output. The pathname components each appear on
a separate line of output, though that does not appear to be the
intended display behavior. The preferred way to generate continued
lines of output on the console is to use pr_cont().
Note that incoming pathname4 components contain a string that is not
necessarily NUL-terminated. I did actually see some trailing garbage
on the console. In addition to correcting the line continuation
problem, add a string precision format specifier to ensure that each
component string is displayed properly, and that vsnprintf() does
not Oops.
Someone pointed out that allowing incoming network data to possibly
generate a console line of unbounded length may not be such a good
idea. Since this output will rarely be enabled, and there is a hard
upper bound (NFS4_PATHNAME_MAXCOMPONENTS) in our implementation, this
is probably not a major concern.
It might be useful to additionally sanity-check the length of each
incoming component, however. RFC 3530bis15 does not suggest a maximum
number of UTF-8 characters per component for either the pathname4 or
component4 types. However, we could invent one that is appropriate
for our implementation.
Another possibility is to scrap all of this and print these pathnames
in upper layers after a reasonable amount of sanity checking in the
XDR layer. This would give us an opportunity to allocate a full
buffer so that the whole pathname would be output via a single
dprintk.
Introduced by commit 7aaa0b3b: "NFSv4: convert fs-locations-components
to conform to RFC3530," (June 9, 2006).
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Eliminate a number of implicit type casts in comparisons, and these
compiler warnings:
fs/nfs/dir.c: In function ‘nfs_readdir_clear_array’:
fs/nfs/dir.c:264:16: warning: comparison between signed and unsigned
integer expressions [-Wsign-compare]
fs/nfs/dir.c: In function ‘nfs_readdir_search_for_cookie’:
fs/nfs/dir.c:352:16: warning: comparison between signed and unsigned
integer expressions [-Wsign-compare]
fs/nfs/dir.c: In function ‘nfs_do_filldir’:
fs/nfs/dir.c:769:38: warning: comparison between signed and unsigned
integer expressions [-Wsign-compare]
fs/nfs/dir.c:780:9: warning: comparison between signed and unsigned
integer expressions [-Wsign-compare]
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The 'minorversion' mount option is now deprecated, so we need to display
the minor version number in the 'vers=' format.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Allow the user to mount an NFSv4.0 or NFSv4.1 partition using a
standard syntax of '-overs=4.0', or '-overs=4.1' rather than the
more cumbersome '-overs=4,minorversion=1'.
See also the earlier patch by Dros Adamson, which added the
Linux-specific syntax '-ov4.0', '-ov4.1'.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
server_scope would never be freed if nfs4_check_cl_exchange_flags() returned
non-zero
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Send the nfs implementation id in EXCHANGE_ID requests unless the module
parameter nfs.send_implementation_id is 0.
This adds a CONFIG variable for the nii_domain that defaults to "kernel.org".
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch removes the old hashmap-based caching and instead uses a
"request key actor" to place an upcall to the legacy idmapper rather
than going through /sbin/request-key. This will only be used as a
fallback if /etc/request-key.conf isn't configured to use nfsidmap.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The NFS4CLNT_LAYOUTRECALL bit is a long-term impediment to scalability. It
basically stops all other recalls by a given server once any layout recall
is requested.
If the recall is for a different file, then we don't care.
If the recall applies to the same file, then we're in one of two situations:
Either we are in the case of a replay of an existing request, in which case
the session is supposed to deal with matters, or we are dealing with a
completely different request, in which case we should just try to process
it.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The NFS4CLNT_LAYOUTRECALL tests in pnfs_layout_process and
pnfs_update_layout are redundant.
In the case of a bulk layout recall, we're always testing for
the NFS_LAYOUT_BULK_RECALL flay anyway.
In the case of a file or segment recall, the call to
pnfs_set_layout_stateid() updates the layout_header 'barrier'
sequence id, which triggers the test in pnfs_layoutgets_blocked()
and is less race-prone than NFS4CLNT_LAYOUTRECALL anyway.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
v3:
1) Lookup for client is performed from the beginning of the list on each PipeFS
event handling operation.
Lockdep is sad otherwise, because inode mutex is taken on PipeFS dentry
creation, which can be called on mount notification, where this per-net client
lock is taken on clients list walk.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Otherwise we have no guarantee that the net namespace won't just
disappear from underneath us once the task that created it
is destroyed.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Currently, the nfs_parsed_mount_data->net field is initialised in
the nfs_parse_mount_options() function, which means that it only
gets set if we're using text based mounts. The legacy binary
mount interface is therefore broken.
Fix is to initialise the ->net field in nfs_alloc_parsed_mount_data.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
server_scope would never be freed if nfs4_check_cl_exchange_flags() returned
non-zero
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Commit aacd553 (NFSv4.1: cleanup init and reset of session slot tables)
introduces a regression in the session initialisation code. New tables
now find their sequence ids initialised to 0, rather than the mandated
value of 1 (see RFC5661).
Fix the problem by merging nfs4_reset_slot_table() and nfs4_init_slot_table().
Since the tbl->max_slots is initialised to 0, the test in
nfs4_reset_slot_table for max_reqs != tbl->max_slots will automatically
pass for an empty table.
Reported-by: Vitaliy Gusev <gusev.vitaliy@nexenta.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Include RPC statistics from all data servers in /proc/self/mountstats for pNFS
filelayout mounts.
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean up: Fix a debugging message which had an obsolete function name
in it (nfs_follow_mountpoint).
Introduced by commit 36d43a43 "NFS: Use d_automount() rather than
abusing follow_link()" (January 14, 2011)
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
ca_maxoperations:
For the backchannel, the server MUST
NOT change the value the client offers. For the fore channel,
the server MAY change the requested value.
ca_maxrequests:
For the backchannel, the server MUST NOT change the
value the client offers. For the fore channel, the server MAY
change the requested value.
Signed-off-by: Vitaliy Gusev <gusev.vitaliy@nexenta.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Don't allow invalid 'vers' and 'minorversion' combinations in mount options,
such as "vers=3,minorversion=1".
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Don't allocate the legacy idmapper tables until we actually need
them.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
