Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Update copyright date, remove author address and add Roger Tseng.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Set a bit to enable rts5227 and rts5249 to enter a deeper internal
power-saving mode in S3, and recover it after resuming.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
These actions are individual for each reader model, so should be put in
extra_init_hw instead of rtsx_pci_init_hw.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some actions to clear power state should be handled in .shutdown
callback in rtsx_pci_driver. This patch adopts the following measures to
catch this goal:
1. Add a function rtsx_pci_power_off to abstract the common ops in
.shutdown and .suspend
2. Add pcr->ops->force_power_down to fulfill the individual action for
each reader model
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Normally OEMs will set vendor setting to the config space of Realtek
card reader in BIOS stage. This patch reads the setting at the first,
and configure the internal registers according to it, to improve card
reader's compatibility condition.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adding support of model RTL8411B. Since the model is similar to RTL8411,
differences are implemented in rtl8411.c.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
RTS5249 supports SD UHS-II interface.
In order to support SD UHS-II，the definitions of some internal
registers of RTS5249 have to be modified and are different from its
predecessors. So we need this patch to ensure RTS5249 can work, even
SD/MMC stack doesn't support UHS-II interface.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When rtsx_pci_acquire_irq fails in rtsx_pci_probe, we forget to
disable an MSI (if we enabled it). This results in this warning on the
next attempt to load the module:
WARNING: at drivers/pci/msi.c:834 pci_enable_msi_block+0x2a4/0x2b0()
Hardware name: HP EliteBook 840 G1
Modules linked in: rtsx_pci(+) ...
Pid: 4056, comm: modprobe Tainted: G I 3.8.0-9405-gd895cb1-1-vanilla #1
Call Trace:
[<ffffffff81045c6a>] warn_slowpath_common+0x7a/0xc0
[<ffffffff81045cc5>] warn_slowpath_null+0x15/0x20
[<ffffffff81302544>] pci_enable_msi_block+0x2a4/0x2b0
[<ffffffffa05e335a>] rtsx_pci_probe+0x55a/0x720 [rtsx_pci]
...
So properly disable MSI in that case.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Realtek card reader supports both SD and MS card. According to the
settings of rtsx MFD driver, SD host will be probed before MS host.
If we boot/reboot Linux with SD card inserted, the resetting flow of SD
card will succeed, and the following resetting flow of MS is sure to fail.
Then MS upper-level driver will ask rtsx driver to turn power off. This
request leads to the result that the following SD commands fail and SD card
can't be accessed again.
In this commit, Realtek's SD and MS host driver will check whether the card
that upper driver requesting is the one existing in the slot. If not, Realtek's
host driver will refuse the operation to make sure the exlusive accessing
at the same time.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Support new model RTS5227.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Reviewed-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
1. Schedule card detect work at the end of the ISR
2. Callback function ops->cd_deglitch may delay for a period of time.
It is not proper to call this callback when local irq disabled.
3. Card detect flow can't be executed in parallel with other card reader
operations, so it's better to be protected by mutex.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In function rtsx_pci_switch_clock, some variables, such as min_n, max_n,
and max_div, are not necessary. And those assigned values look very
obscure for others. It's more proper to use macro definitions here to
replace these variables.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Realtek PCIe card reader only supports 32bit DMA.
This declaration can improve the readability.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In function rtsx_pci_add_sg_tbl, the statement "ptr++" is useless.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If rtsx_pci_sdmmc is not probed, function pointer pcr->slots[].card_event
will point to NULL, and thus rtsx_pci_card_detect will reference a NULL
pointer.
Check card_event pointer before referencing it can avoid kernel panic.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add callback function conv_clk_and_div_n to convert between SSC clock
and its divider N.
For rtl8411, the formula to calculate SSC clock divider N is different
with the other card reader models.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Different card reader has different method to switch output voltage,
add this callback to let the card reader implement its individual switch
function.
This is needed as rtl8411 has a specific switch output voltage procedure.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the following build error on some architectures (parisc at least):
drivers/mfd/rtsx_pcr.c: In function 'rtsx_pci_init_chip':
drivers/mfd/rtsx_pcr.c:985:2: error: implicit declaration of function 'kcalloc'
[-Werror=implicit-function-declaration]
drivers/mfd/rtsx_pcr.c:985:13: warning: assignment makes pointer from integer
without a cast [enabled by default]
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
