Now that the V4L bits have finally settled..
This patch adds support for a secondary ov772x camera on ap325rxa.
This is supported in addition to the regular soc_camera_platform camera.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All soc-camera camera and host drivers must specify supported data signal
polarity, after all drivers are fixed, we'll add a suitable test to
soc_camera_bus_param_compatible().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Waiting for a free bus now accepts the timeout value in jiffies and does
proper checking using time_before.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Polaris is an SMSC reference platform with a SH7709S CPU and LAN9118
ethernet controller. This patch adds support for it.
Updated following feedback from Nobuhiro Iwamatsu.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rework the hd64461 demuxer code to fix the HD64461 level-triggered
interrupts handling, using handle_level_irq() as needed.
Signed-off-by: Rafael Ignacio Zurita <rizurita@yahoo.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
IRQ for sh_eth of sh7763rdp became multi handling.
Therefore, the IRQ number of sh_eth is changed, too.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the ESPT-Giga (Ethernet Serial Parallel
Translator) SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve the ap325 board code to allow the lcd panel
and backlight to be powered off.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve the sh7785lcr power off implementation to
never return. It takes some time before the board
is actually powered off, just hang after asking
the harware to power down.
This removes the serial port garbage printout.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a new defconfig for SH7785LCR in 32-bit mode, and update the power
off code to avoid 29-bit assumptions.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If CONFIG_PM is set, let Migo-R LEDs show sleep states.
D11 will show STATUS0 and D12 PDSTATUS.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Other compilation errors were revised by commit of
"sh: ap325rxa: Revert ov772x support"
(08c2f5b4d7) but other compilation
errors are given.
We revert this commit and need to add new header(media/soc_camera.h).
This change revises new compilation error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7786-based Urquell board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the sh3/sh4/sh4a register saving code in
the following ways:
- break out prepare_stack_save_dsp() from handle_exception()
- break out save_regs() from handle_exception()
- the register saving order is unchanged
- align new functions to fit in cache lines
- separate exception code from interrupt code
- keep main code flow in a single cache line per exception vector
- use bsr/rts for regular functions (save pr first)
- keep data in one shared cache line (exception_data)
- document the functions
- tie in the hp6xx code
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This change depends on some v4l changes that have been pushed back to
2.6.30, so drop this and fall back on the old soc_camera code until then.
Reported-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Acked-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch add ov772x camera settings to ap325,
Old camera is still supported. And it will be 2nd camera
if you select ov772x and soc_camera_platform in same time.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix up the build for mach-highlander and mach-rsk. These operated on the
assumption that GENERIC_GPIO support with an optional GPIOLIB was
possible. This used to be true, but has not been the case since commit-id
d56cc8bc661ac1ceded8d45ba2d53bb134fee17d ("sh: use gpiolib"), where the
GENERIC_GPIO implementation was rewritten to use GPIOLIB directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the SuperH gpio code to make use of gpiolib. The
gpiolib callbacks get() and set() are lockless, but we use our own
spinlock for the other operations to make sure hardware register
bitfield accesses stay atomic.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds CN9 MMC support for MigoR using the mmc_spi
driver on top of the bitbanging spi_gpio driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds CN3 MMC support for ap325rxa using the mmc_spi
driver on top of the bitbanging spi_gpio driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since commit ba84be2338
("remove linux/hardirq.h from asm-generic/local.h"), the asm/irq.h
definitions that mach-x3proto/setup.c depends on are no longer available,
causing the build to die. So, include linux/irq.h explicitly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Migo-R can use ov772x camera driver in Linux 2.6.29.
Therefore, soc_camera_platform setting is no longer needed.
This patch removes it.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Enable LCDC deferred io on Migo-R using 1s delay.
As with other deferred io frame buffers user space code should
use fsync() on the frame buffer device to trigger an update.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add LCDC interrupt resources for AP325 and Migo-R. The LCDC driver does
not require interrupts at this point, but changes such as one-shot SYS
mode using deferred io, and wait-for-vblank will both need this.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the rest of the boards that were using cf-enabler "generically"
have switched to setting up their mappings on their own, only the mach-se
boards were left using it. All of the cf-enabler using mach-se boards
use a special initialization of the MRSHPC windows rather than going
through the special PTE as other SH-4 platforms do. This consolidates
the MRSHPC setup logic, hooks it up on the boards that care, and gets rid
of any and all remaining references to cf-enabler.
This has been long overdue, as cf-enabler has been the bane of
arch/sh/kernel for the last 7 years. Good riddance.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This also fixes up a long-standing bug for this platform where the PIO
base was set to a register offset, rather than the actual PIO offset
itself.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This gets rid of the cf enabler use on mach-sh03 and switches to use
pata_platform with the proper address directly. cf_enabler is
subsequently disabled for mach-sh03.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I've been unable to even compile-test this change because I don't have
an sh5 toolchain. All uses of hw_interrupt_type for SuperH boards have
now been converted to use irq_chip.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Switch the dreamcast IRQ code over to the irq_chip way of doing things,
so that we can set GENERIC_HARDIRQS_NO__DO_IRQ for all SuperH boards.
Also, whilst I'm here change some things to make checkpatch.pl happy:
- Indent with tabs, not with spaces
- Include <linux/io.h>, not <asm/io.h>
- Fix the multi-line comment style
- Fix some typos in the comments
Tested-by: Adrian McMenamin <adrian@newgolddream.dyndns.info>
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This kills off the special Migo-R machvec, as nothing is using it. By
default this will switch to using the generic machvec, which provides the
same functionality. This saves us a bit of space in the machvec section.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
RSK+ platforms have quite a few characteristics in common, so roll them
together in to a shiny new RSK mach-type.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the not-so-generic pm code from arch/sh/kernel/pm.c to the
platform directory together with the rest of the hp6xx pm code.
This is done to let non-hp6xx platforms enable CONFIG_PM.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove out-of-date se7343 ioport code including some old support
for unknown-ne2000-pcmcia-card, cf-over-pcmcia and a mysterical
smc91x that once must have been on a special daughterboard.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add isp1161 platform data to get usb host working on se7343.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add 8250 platform data to setup the ST16C2550C chip on se7343.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix to make sure that the on-board interrupt sources are included
in the interrupt count on se7343.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the RTE RSK+ 7201 board.
Signed-off-by: Peter Griffin <pgriffin@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the lcdc driver and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the sh_mobile ceu and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the sh_mobile keysc driver and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use a slower VIO_CKO clock frequency for the ov772x on Migo-R.
This improves the camera picture quality on Panel Board V2.1.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the ov772x byte sequence to enable byte swap. This to reflect
the recent CEU driver change to follow incoming byte order.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sh7203.h include paths were missed in the previous update, so switch
the include path to cpu/ as with the rest.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve Migo-R ethernet performance by reducing smc91x overruns.
This is done by enabling SMC91X_NOWAIT and optimizing CS4 setup.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Renesas AP325RXA board has Epson RX-8564LC of RTC.
This patch supports RTC of this board.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch hooks up the magicpanelr2 board with the sh7720 pinmux code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make the rsk7203 board use the newly added sh7203 pinmux code.
Only a single LED plus the serial console pins for now.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the GPIO code on AP325RXA and converts the code from
register based pinmux configuration to GPIO based pin by pin setup.
While at it 2 LEDs and one switch are added and exported to user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the GPIO code on Migo-R and converts the code from
register based pinmux configuration to GPIO based pin by pin setup.
Fix whitespace damage while at it and add 2 LEDs and export them to
user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a workaround for users of sh_mobile_lcdcfb that don't
define HAVE_CLK and have otherwise sane clock initialization.
At the same time, move the sh_mobile_lcdc.h header to include/video/.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
AP320 and AP325RXA has CPLD data in NOR Flash.
If this area erased, this board can not boot.
This patch create CPLD data area and set writeable mask bit.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is 256K instead of 1M.
[ Converted to use asm/sizes.h. -- PFM ]
Signed-off-by: Luca Santini <luca.santini@spesonline.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the Renesas (RTE) EDOSK7760 board. Currently
supported devices are:
- ramdisk support
- ethernet support
- nfs support
- ext2/ext3 support
- i2c support
- fb support (M)
Signed-off-by: Luca Santini <luca.santini@spesonline.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Export the LCD panel size for sh_mobile_lcdc boards. This allows us
to perform dpi and screen aspect ratio calculations in user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7763 has sh_eth device. This patch add sh_eth platform device
to this board.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch remove unneeded #include <linux/ide.h>'s.
It also adds a required #include <linux/interrupt.h> that was previously
implicitely pulled by ide.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
[bart: revert change to tests/lkdtm.c (spotted by Stephen Rothwell)]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Removed duplicated include <linux/irq.h> in
arch/sh/boards/mach-se/7343/irq.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Removed duplicated include <linux/delay.h> in
arch/sh/boards/board-ap325rxa.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The following build error was caused by an obvious typo:
<-- snip -->
...
LD arch/sh/mm/built-in.o
make[2]: *** No rule to make target `arch/sh/boards/board-shmin..o', needed by `arch/sh/boards/built-in.o'. Stop.
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix recently introduced I2C build breakage on AP325RXA and Migo-R.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This flattens out the board directories in to individual mach groups,
we will use this for getting rid of unneeded directories, simplifying
the build system, and becoming more coherent with the refactored
arch/sh/include topology.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When I compiled Solution Engine, this become compile error
because plaform device of sh_eth device becomes enable.
When sh7710/sh7712 which could use sh_eth was chosen,
revised it so that platform device of sh_eth device became enable.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Oops, machvec.h is in asm/, it was previously removed due to overzealous
trimming. Fix up the path again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the sparc changes a439fe51a1.
Most of the moving about was done with Sam's directions at:
http://marc.info/?l=linux-sh&m=121724823706062&w=2
with subsequent hacking and fixups entirely my fault.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add AP325RXA specific platform data for on-chip sh7723 CEU and ncm03j camera.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pass board specific smc911x parameters using struct smc911x_platdata.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add Migo-R specific platform data for on-chip sh7722 CEU and ov772x camera.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7343 processor and in the board code
for Solution Engine 7343. Remove duplicate MSTPCR register definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7722 processor and in the board code
for Migo-R and Solution Engine 7722. Remove duplicate MSTPCR register
definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7723 processor and in the ap325rxa
board code. Remove duplicate MSTPCR register definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds initial support for the Renesas R0P7785LC0011RL board.
This patch supports 29bit address mode only.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
updated the following codes for Solution Endine 7343:
- fix compile error in arch/sh/boards/se/7343/irq.c
- add nor flash physmaps
- update defconfig
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables I2C on the sh7723-based ap325rxa board.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh_pcic_io_xxx function are very old.
In linux-2.4, mrshpc_ss socket driver used this function.
But there is not this driver to the present kernel.
I deleted these cords and checked operation.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support SH-Ether for Hitachi Solution Engine.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes the needlessly global aica_rtc_{get,set}timeofday()
static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds basic support for the SH7763RDP board.
This supports a basic stuff provided in SH7763, like SCIF,
NOR Flash and USB host.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This board is SH7723 base board.
This has SCIF, LCDC, USB Host controler, NOR/NAND Flash, Sound,
Ether and other.
This patch supports SCIF, NOR Flash.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (85 commits)
[ARM] pxa: add base support for PXA930 Handheld Platform (aka SAAR)
[ARM] pxa: add base support for PXA930 Evaluation Board (aka TavorEVB)
[ARM] pxa: add base support for PXA930 (aka Tavor-P)
[ARM] Update mach-types
[ARM] pxa: make littleton to use the new smc91x platform data
[ARM] pxa: make zylonite to use the new smc91x platform data
[ARM] pxa: make mainstone to use the new smc91x platform data
[ARM] pxa: make lubbock to use new smc91x platform data
[NET] smc91x: prepare SMC_USE_PXA_DMA to be specified in platform data
[NET] smc91x: prepare for SMC_IO_SHIFT to be a platform configurable variable
[NET] smc91x: add SMC91X_NOWAIT flag to platform data
[NET] smc91x: favor the use of SMC91X_USE_* instead of SMC_CAN_USE_*
[NET] smc91x: remove "irq_flags" from "struct smc91x_platdata"
[ARM] 5146/1: pxa2xx: convert all boards to call pxa2xx_transceiver_mode helper
Support for LCD on e740 e750 e400 and e800 e-series PDAs
E-series UDC support
PXA UDC - allow use of inverted GPIO for pullup
Add e350 support
Fix broken e-series build
E-series GPIO / IRQ definitions.
...
IRQ trigger type can be specified in the IRQ resource definition by
IORESOURCE_IRQ_*, we need only one way to specify this.
This also fixes the following small issue:
To allow dynamic support for multiple platforms, when those relevant
macros are not defined for one specific platform, the default case
will be:
- SMC_DYNAMIC_BUS_CONFIG defined
- and SMC_IRQ_FLAGS = IRQF_TRIGGER_RISING
While if "irq_flags" is missing when defining the smc91x_platdata,
usually as follows:
static struct smc91x_platdata xxxx_smc91x_data = {
.flags = SMC91X_USE_XXBIT,
};
The lp->cfg.irq_flags will always be overriden by the above structure
(due to a memcpy), thus rendering lp->cfg.irq_flags to be "0" always.
(regardless of the default SMC_IRQ_FLAGS or IORESOURCE_IRQ_* flags)
Fixes this by forcing to use IORESOURCE_IRQ_* flags if present, and
make the only user of smc91x_platdata.irq_flags (renesas/migor) to
use IORESOURCE_IRQ_*.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make use of recently added sm501 8250 uart support, commit
61711f8fd8 makes the mfd code
handle 8250 uarts so there is no longer need to do it from
the r2d board code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Select smc91x bus width using platform data for se7722 now when the
smc91x header file is in place.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Select smc91x bus width and irg flags using platform data for MigoR
now when the smc91x header file is in place.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH_MPC1211 has been marked as BROKEN for some time.
Unless someone is working on reviving it now, I'd therefore suggest this
patch to remove it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Add support for the migor_ts touch panel to the MigoR board.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add NAND flash support to the MigoR board by giving board specific data
to the gen_nand platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add NOR flash support to the MigoR board by giving board specific data
to the physmap-flash platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use physical addresses and change resource name of MigoR ethernet chip.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a MigoR specific header file. We may want to use a cpu
specific header file instead, but this will do for now.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for Solution Engine SH7721 board(MS7721RP01).
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add KEYSC platform data for the Solution Engine 7722 board.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add KEYSC platform data for the sh7722 MigoR board.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The only board-specific bits that existed here were for setting up the
IRQs, which are now handled by the SH7710 CPU support code instead. As
there's nothing else to do for setup, kill off the board support code
and have the defconfig use the generic machvec instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
