When virtfn is used, we should use physfn to find correct drhd
-v2: add pci_physfn() Suggested by Roland Dreier <rdreier@cisco.com>
do can remove ifdef in dmar.c
-v3: Chris pointed out we need that for dma_find_matched_atsr_unit too
also change dmar_pci_device_match() static
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Roland Dreier <rdreier@cisco.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
While it may be efficient on real hardware, emulation of global
invalidations is very expensive as all shadow entries must be examined.
This patch changes the behaviour when caching mode is enabled (which is
the case when IOMMU emulation takes place). In this case, page specific
invalidation is used instead.
Signed-off-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In caching-mode mappings of pages (changes from non-present to present)
require invalidation.
Currently, this IOTLB flush is performed with domain ID of zero.
This is not according to the VT-d spec and causes big problems for
emulating software.
This patch uses the correct domain ID in IOTLB flushes.
Device IOTLB invalidation is performed only on present to non-present
changes. This decision is now based on explicit parameter instead of
zero domain-ID.
Signed-off-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
intel_map_sg used offset_pfn which was set to zero when invalidating the IOTLB.
intel_map_sg now uses size variable for this matter.
Signed-off-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Replace open-coded loop with for_each_set_bit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
While testing completion timeouts I found that hardware was not recovering.
It looks like the hot reset was never being propagated to the endpoint
devices on the bus due to the fact that we were clearing the bit too
quickly.
The documentation I have states that we should be transmitting hot reset
TS1s for 2ms. To achieve this I have added a 2ms delay from the time we
set the secondary bus reset bit to the time we clear it. In addition I
changed the define used for the secondary bus reset bit to match the
register define that was being used.
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The missing initialization of the nb_cntl.strap_msi_enable does not
seem to be the only problem that prevents MSI, so that quirk is not
sufficient to enable MSI on all machines. To be safe, disable MSI
unconditionally for the internal graphics and HDMI audio on these
chipsets.
[rjw: Added the PCI_VENDOR_ID_AI quirk.]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI: truncate _CRS windows with _LEN > _MAX - _MIN + 1
x86/PCI: for host bridge address space collisions, show conflicting resource
frv/PCI: remove redundant warnings
x86/PCI: remove redundant warnings
PCI: don't say we claimed a resource if we failed
PCI quirk: Disable MSI on VIA K8T890 systems
PCI quirk: RS780/RS880: work around missing MSI initialization
PCI quirk: only apply CX700 PCI bus parking quirk if external VT6212L is present
PCI: complain about devices that seem to be broken
PCI: print resources consistently with %pR
PCI: make disabled window printk style match the enabled ones
PCI: break out primary/secondary/subordinate for readability
PCI: for address space collisions, show conflicting resource
resources: add interfaces that return conflict information
PCI: cleanup error return for pcix get and set mmrbc functions
PCI: fix access of PCI_X_CMD by pcix get and set mmrbc functions
PCI: kill off pci_register_set_vga_state() symbol export.
PCI: fix return value from pcix_get_max_mmrbc()
pci_claim_resource() can fail, so pay attention and only claim success
when it actually succeeded. If pci_claim_resource() fails, it prints a
useful diagnostic.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla 15287 indicates that there's a problem with Message Signalled
Interrupts on VIA K8T890 systems. Add a quirk to disable MSI on these
systems.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Tested-by: Jan Kreuzer <kontrollator@gmx.de>
Tested-by: lh <jarryson@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
AMD says in section 2.5.4 (GFX MSI Enable) of #43291 (AMD 780G Family
Register Programming Requirements):
The SBIOS must enable internal graphics MSI capability in GCCFG by
setting the following: NBCFG.NB_CNTL.STRAP_MSI_ENABLE='1'
Quite a few BIOS writers misinterpret this sentence and think that
enabling MSI is an optional feature. However, clearing that bit just
prevents delivery of MSI messages but does not remove the MSI PCI
capabilities registers, and so leaves these devices unusable for any
driver that attempts to use MSI.
Setting that bit is not possible after the BIOS has locked down the
configuration registers, so we have to manually disable MSI for the
affected devices.
This fixes the codec communication errors in the HDA driver when
accessing the HDMI audio device, and allows us to get rid of the
overcautious quirk in radeon_irq_kms.c.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Alex Deucher <alexdeucher@gamil.com>
Cc: <stable@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Apply the CX700 quirk only when an external VT6212L is present (which
is the case for the errant hardware the quirk was written for), don't
touch the settings otherwise -- Hauppage PVR-500 tuners need PCI Bus
Parking in order to work and when that's turned on everything seems
to behave fine.
I guess the underlying problem is a combination of an external VT6212L
and the CX700 rather than the CX700's PCI being broken completely for
all cases...
Reported-by: Jeroen Roos <jeroen@roosnl.com>
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If we can tell that a device isn't working correctly, we should tell
the user to make debugging easier. Otherwise, it can take a lot of
work to determine whether the problem is in the driver, PCMCIA, PCI,
hardware, etc., as in http://bugzilla.kernel.org/show_bug.cgi?id=12006
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; just print resources in the conventional style.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; this just tweaks the changes from 349e1823a405
so the new printks for disabled PCI-to-PCI bridge windows match the
ones for the enabled windows.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; just add names for the primary/secondary/subordinate
bus numbers read from config space rather than repeatedly masking/shifting.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
With request_resource_conflict(), we can learn what the actual conflict is,
so print that info for debugging purposes.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver core: numa: fix BUILD_BUG_ON for node_read_distance
driver-core: document ERR_PTR() return values
kobject: documentation: Update to refer to kset-example.c.
sysdev: the cpu probe/release attributes should be sysdev_class_attributes
kobject: documentation: Fix erroneous example in kobject doc.
driver-core: fix missing kernel-doc in firmware_class
Driver core: Early platform kernel-doc update
sysfs: fix sysfs lockdep warning in mlx4 code
sysfs: fix sysfs lockdep warning in infiniband code
sysfs: fix sysfs lockdep warning in ipmi code
sysfs: Initialised pci bus legacy_mem field before use
sysfs: use sysfs_bin_attr_init in firmware class driver
pcix_get_mmrbc() returns the maximum memory read byte count (mmrbc), if
successful, or an appropriate error value, if not.
Distinguishing errors from correct values and understanding the meaning of an
error can be somewhat confusing in that:
correct values: 512, 1024, 2048, 4096
errors: -EINVAL -22
PCIBIOS_FUNC_NOT_SUPPORTED 0x81
PCIBIOS_BAD_VENDOR_ID 0x83
PCIBIOS_DEVICE_NOT_FOUND 0x86
PCIBIOS_BAD_REGISTER_NUMBER 0x87
PCIBIOS_SET_FAILED 0x88
PCIBIOS_BUFFER_TOO_SMALL 0x89
The PCIBIOS_ errors are returned from the PCI functions generated by the
PCI_OP_READ() and PCI_OP_WRITE() macros.
In a similar manner, pcix_set_mmrbc() also returns the PCIBIOS_ error values
returned from pci_read_config_[word|dword]() and pci_write_config_word().
Following pcix_get_max_mmrbc()'s example, the following patch simply returns
-EINVAL for all PCIBIOS_ errors encountered by pcix_get_mmrbc(), and -EINVAL
or -EIO for those encountered by pcix_set_mmrbc().
This simplification was chosen in light of the fact that none of the current
callers of these functions are interested in the specific type of error
encountered. In the future, should this change, one could simply create a
function that maps each PCIBIOS_ error to a corresponding unique errno value,
which could be called by pcix_get_max_mmrbc(), pcix_get_mmrbc(), and
pcix_set_mmrbc().
Additionally, this patch eliminates some unnecessary variables.
Cc: stable@kernel.org
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
An e1000 driver on a system with a PCI-X bus was always being returned
a value of 135 from both pcix_get_mmrbc() and pcix_set_mmrbc(). This
value reflects an error return of PCIBIOS_BAD_REGISTER_NUMBER from
pci_bus_read_config_dword(,, cap + PCI_X_CMD,).
This is because for a dword, the following portion of the PCI_OP_READ()
macro:
if (PCI_##size##_BAD) return PCIBIOS_BAD_REGISTER_NUMBER;
expands to:
if (pos & 3) return PCIBIOS_BAD_REGISTER_NUMBER;
And is always true for 'cap + PCI_X_CMD', which is 0xe4 + 2 = 0xe6. ('cap' is
the result of calling pci_find_capability(, PCI_CAP_ID_PCIX).)
The same problem exists for pci_bus_write_config_dword(,, cap + PCI_X_CMD,).
In both cases, instead of calling _dword(), _word() should be called.
Cc: stable@kernel.org
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When pci_register_set_vga_state() was made __init, the EXPORT_SYMBOL() was
retained, which now leaves us with a section mismatch.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Mike Travis <travis@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For the PCI_X_STATUS register, pcix_get_max_mmrbc() is returning an incorrect
value, which is based on:
(stat & PCI_X_STATUS_MAX_READ) >> 12
Valid return values are 512, 1024, 2048, 4096, which correspond to a 'stat'
(masked and right shifted by 21) of 0, 1, 2, 3, respectively.
A right shift by 11 would generate the correct return value when 'stat' (masked
and right shifted by 21) has a value of 1 or 2. But for a value of 0 or 3 it's
not possible to generate the correct return value by only right shifting.
Fix is based on pcix_get_mmrbc()'s similar dealings with the PCI_X_CMD register.
Cc: stable@kernel.org
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PPC64 is failing to boot the latest mmotm due to an uninitialised pointer in
pci_create_legacy_files(). The surprise is that machines boot at all and it
would appear to affect current mainline as well. This patch fixes the problem.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze: (27 commits)
microblaze: entry.S use delay slot for return handlers
microblaze: Save current task directly
microblaze: Simplify entry.S - save/restore r3/r4 - ret_from_trap
microblaze: PCI early support for noMMU system
microblaze: Fix dma alloc and free coherent dma functions
microblaze: Add consistent code
microblaze: pgtable.h: move consistent functions
microblaze: Remove ancient Kconfig option for consistent mapping
microblaze: Remove VMALLOC_VMADDR
microblaze: Add define for ASM_LOOP
microblaze: Preliminary support for dma drivers
microblaze: remove trailing space in messages
microblaze: Use generic show_mem()
microblaze: Change temp register for cmdline
microblaze: Preliminary support for dma drivers
microblaze: Move cache function to cache.c
microblaze: Add support from PREEMPT
microblaze: Add support for Xilinx PCI host bridge
microblaze: Enable PCI, missing files
microblaze: Add core PCI files
...
Per ACPI spec, _ERG method should be executed before device driver
gets control for hotpluged device. Firmware might do some configuration
there. See http://bugzilla.kernel.org/show_bug.cgi?id=10805. In this
machine, _REG method of docked device will configure cardbus bridge.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Tested-by: Paul Martin <pm@debian.org>
Signed-off-by: Len Brown <len.brown@intel.com>
We can use pci-dma-compat.h to implement pci_set_dma_mask and
pci_set_consistent_dma_mask as we do with the other PCI DMA API.
We can remove HAVE_ARCH_PCI_SET_DMA_MASK too.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_set_coherent_mask corresponds to pci_set_consistent_dma_mask. This is
necessary to move to the generic device model DMA API from the PCI bus
specific API in the long term.
dma_set_coherent_mask works in the exact same way that
pci_set_consistent_dma_mask does. So this patch also changes
pci_set_consistent_dma_mask to call dma_set_coherent_mask.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes pci_set_dma_mask to call the generic DMA API, dma_set_mask.
pci_set_dma_mask (in drivers/pci/pci.c) does the same things that
dma_set_mask does on all the architectures that use pci_set_dma_mask;
calls dma_supprted and sets dev->dma_mask. So we safely change
pci_set_dma_mask to simply call dma_set_mask.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are two parts of changes. The first is just enable
PCI in Makefiles and in Kconfig. The second is the rest of
missing files. I didn't want to add it with previous patch
because that patch is too big.
Current Microblaze toolchain has problem with weak symbols
that's why is necessary to apply this changes to be possible
to compile pci support.
Xilinx knows about this problem.
Signed-off-by: Michal Simek <monstr@monstr.eu>
In the future, we are going to be changing the lock type for struct
device (once we get the lockdep infrastructure properly worked out) To
make that changeover easier, and to possibly burry the lock in a
different part of struct device, let's create some functions to lock and
unlock a device so that no out-of-core code needs to be changed in the
future.
This patch creates the device_lock/unlock/trylock() functions, and
converts all in-tree users to them.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Cc: Magnus Damm <damm@igel.co.jp>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Alex Chiang <achiang@hp.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Yu Zhao <yu.zhao@intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: CHENG Renquan <rqcheng@smu.edu.sg>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Frans Pop <elendil@planet.nl>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After merging the final tree, today's linux-next build (powerpc
allyesconfig) failed like this:
drivers/pci/pci-sysfs.c: In function 'pci_create_legacy_files':
drivers/pci/pci-sysfs.c:645: error: lvalue required as unary '&' operand
drivers/pci/pci-sysfs.c:658: error: lvalue required as unary '&' operand
Caused by commit "sysfs: Use sysfs_attr_init and sysfs_bin_attr_init on
dynamic attributes" interacting with commit "sysfs: Use one lockdep
class per sysfs attribute") both from the driver-core tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These are the non-static sysfs attributes that exist on
my test machine. Fix them to use sysfs_attr_init or
sysfs_bin_attr_init as appropriate. It simply requires
making a sysfs attribute present to see this. So this
is a little bit tedious but otherwise not too bad.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the iommu-api functions for mapping and
unmapping page ranges to use the new page-size based
interface. This allows to remove the range based functions
later.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The new function pointer names match better with the
top-level functions of the iommu-api which are using them.
Main intention of this change is to make the ->{un}map
pointer names free for two new mapping functions.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch solves nasty problem original driver has.
Original goal of the ricoh_mmc was to disable this device because then,
mmc cards can be read using standard SDHCI controller, thus avoiding
writing of yet another driver.
However, the act of disablement, makes other pci functions that belong to
this controller (xD and memstick) shift up one level, thus pci core has
now wrong idea about these devices.
To fix this issue, this patch moves the driver into the pci quirk section,
thus it is executes before the pci is enumerated, and therefore solving
that issue, also same sequence of commands is performed on resume for same
reasons.
Also regardless of the above, this way is cleaner. You still need to set
CONFIG_MMC_RICOH_MMC to enable this quirk
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Philip Langdale <philipl@overt.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the run-time power management of PCI devices be inactive by
default by calling pm_runtime_forbid() for each PCI device during its
initialization. This setting may be overriden by the user space with
the help of the /sys/devices/.../power/control interface.
That's necessary to avoid breakage on systems where ACPI-based
wake-up is known to fail for some devices.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'x86-bootmem-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
early_res: Need to save the allocation name in drop_range_partial()
sparsemem: Fix compilation on PowerPC
early_res: Add free_early_partial()
x86: Fix non-bootmem compilation on PowerPC
core: Move early_res from arch/x86 to kernel/
x86: Add find_fw_memmap_area
Move round_up/down to kernel.h
x86: Make 32bit support NO_BOOTMEM
early_res: Enhance check_and_double_early_res
x86: Move back find_e820_area to e820.c
x86: Add find_early_area_size
x86: Separate early_res related code from e820.c
x86: Move bios page reserve early to head32/64.c
sparsemem: Put mem map for one node together.
sparsemem: Put usemap for one node together
x86: Make 64 bit use early_res instead of bootmem before slab
x86: Only call dma32_reserve_bootmem 64bit !CONFIG_NUMA
x86: Make early_node_mem get mem > 4 GB if possible
x86: Dynamically increase early_res array size
x86: Introduce max_early_res and early_res_count
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1341 commits)
virtio_net: remove forgotten assignment
be2net: fix tx completion polling
sis190: fix cable detect via link status poll
net: fix protocol sk_buff field
bridge: Fix build error when IGMP_SNOOPING is not enabled
bnx2x: Tx barriers and locks
scm: Only support SCM_RIGHTS on unix domain sockets.
vhost-net: restart tx poll on sk_sndbuf full
vhost: fix get_user_pages_fast error handling
vhost: initialize log eventfd context pointer
vhost: logging thinko fix
wireless: convert to use netdev_for_each_mc_addr
ethtool: do not set some flags, if others failed
ipoib: returned back addrlen check for mc addresses
netlink: Adding inode field to /proc/net/netlink
axnet_cs: add new id
bridge: Make IGMP snooping depend upon BRIDGE.
bridge: Add multicast count/interval sysfs entries
bridge: Add hash elasticity/max sysfs entries
bridge: Add multicast_snooping sysfs toggle
...
Trivial conflicts in Documentation/feature-removal-schedule.txt
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: replace acpi_integer by u64
ACPICA: Update version to 20100121.
ACPICA: Remove unused uint32_struct type
ACPICA: Disassembler: Remove obsolete "Integer64" field in parse object
ACPICA: Remove obsolete ACPI_INTEGER (acpi_integer) type
ACPICA: Predefined name repair: fix NULL package elements
ACPICA: AcpiGetDevices: Eliminate unnecessary _STA calls
ACPICA: Update all ACPICA copyrights and signons to 2010
ACPICA: Update for new gcc-4 warning options
A ROM resource that doesn't fit should not cause us to try to re-assign
all the bus resources. Nobody generally cares, and re-assigning is
going to just cause way more troubles than it tries to solve.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-pci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Enable NMI on all cpus on UV
vgaarb: Add user selectability of the number of GPUS in a system
vgaarb: Fix VGA arbiter to accept PCI domains other than 0
x86, uv: Update UV arch to target Legacy VGA I/O correctly.
pci: Update pci_set_vga_state() to call arch functions
This patch adds the pci_vpd_find_info_keyword() helper function to
find information field keywords within read-only and read-write large
resource data type sections.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the pci_vpd_find_tag() helper function to find VPD
resource data types in a buffer.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set power.async_suspend for all PCI devices and PCIe port services,
so that they can be suspended and resumed in parallel with other
devices they don't depend on in a known way (i.e. devices which are
not their parents or children).
This only affects the "regular" suspend and resume stages, which
means in particular that the restoration of the PCI devices' standard
configuration registers during resume will still be carried out
synchronously (at the "early" resume stage).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Previously we used a table of size PCI_BUS_NUM_RESOURCES (16) for resources
forwarded to a bus by its upstream bridge. We've increased this size
several times when the table overflowed.
But there's no good limit on the number of resources because host bridges
and subtractive decode bridges can forward any number of ranges to their
secondary buses.
This patch reduces the table to only PCI_BRIDGE_RESOURCE_NUM (4) entries,
which corresponds to the number of windows a PCI-to-PCI (3) or CardBus (4)
bridge can positively decode. Any additional resources, e.g., PCI host
bridge windows or subtractively-decoded regions, are kept in a list.
I'd prefer a single list rather than this split table/list approach, but
that requires simultaneous changes to every architecture. This approach
only requires immediate changes where we set up (a) host bridges with more
than four windows and (b) subtractive-decode P2P bridges, and we can
incrementally change other architectures to use the list.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; this converts loops that iterate from 0 to
PCI_BUS_NUM_RESOURCES through pci_bus resource[] table to use the
pci_bus_for_each_resource() iterator instead.
This doesn't change the way resources are stored; it merely removes
dependencies on the fact that they're in a table.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; this fills in the bus subtractive decode resources
after reading the bridge window information rather than before. Also,
print out the subtractive decode resources as we already do for the
positive decode windows.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; this breaks up pci_read_bridge_bases() into separate
pieces for the I/O, memory, and prefetchable memory windows, similar to how
Yinghai recently split up pci_setup_bridge() in 68e84ff3bdc.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe
capability offset. This reduces redundant search in PCI configuration
space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce run-time PM callbacks for the PCI bus type. Make the new
callbacks work in analogy with the existing system sleep PM
callbacks, so that the drivers already converted to struct dev_pm_ops
can use their suspend and resume routines for run-time PM without
modifications.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_is_pcie() instead of looking at obsolete is_pcie field in
struct pci_dev.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Although the majority of PCI devices can generate PMEs that in
principle may be used to wake up devices suspended at run time,
platform support is generally necessary to convert PMEs into wake-up
events that can be delivered to the kernel. If ACPI is used for this
purpose, PME signals generated by a PCI device will trigger the ACPI
GPE associated with the device to generate an ACPI wake-up event that
we can set up a handler for, provided that everything is configured
correctly.
Unfortunately, the subset of PCI devices that have GPEs associated
with them is quite limited. The devices without dedicated GPEs have
to rely on the GPEs associated with other devices (in the majority of
cases their upstream bridges and, possibly, the root bridge) to
generate ACPI wake-up events in response to PME signals from them.
Add ACPI platform support for PCI PME wake-up:
o Add a framework making is possible to use ACPI system notify
handlers for run-time PM.
o Add new PCI platform callback ->run_wake() to struct
pci_platform_pm_ops allowing us to enable/disable the platform to
generate wake-up events for given device. Implemet this callback
for the ACPI platform.
o Define ACPI wake-up handlers for PCI devices and PCI root buses and
make the PCI-ACPI binding code register wake-up notifiers for all
PCI devices present in the ACPI tables.
o Add function pci_dev_run_wake() which can be used by PCI drivers to
check if given device is capable of generating wake-up events at
run time.
Developed in cooperation with Matthew Garrett <mjg@redhat.com>.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Apparently, some machines may have problems with PCI run-time power
management if MSIs are used for the native PCIe PME signaling. In
particular, on the MSI Wind U-100 PCIe PME interrupts are not
generated by a PCIe root port after a resume from suspend to RAM, if
the system wake-up was triggered by a PME from the device attached to
this port. [It doesn't help to free the interrupt on suspend and
request it back on resume, even if that is done along with disabling
the MSI and re-enabling it, respectively.] However, if INTx
interrupts are used for this purpose on the same machine, everything
works just fine.
For this reason, add a kernel command line switch allowing one to
request that MSIs be not used for the native PCIe PME signaling,
introduce a DMI table allowing us to blacklist machines that need
this switch to be set by default and put the MSI Wind U-100 into this
table.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCIe native PME detection mechanism is based on interrupts generated
by root ports or event collectors every time a PCIe device sends a
PME message upstream.
Once a PME message has been sent by an endpoint device and received
by its root port (or event collector in the case of root complex
integrated endpoints), the Requester ID from the message header is
registered in the root port's Root Status register. At the same
time, the PME Status bit of the Root Status register is set to
indicate that there's a PME to handle. If PCIe PME interrupt is
enabled for the root port, it generates an interrupt once the PME
Status has been set. After receiving the interrupt, the kernel can
identify the PCIe device that generated the PME using the Requester
ID from the root port's Root Status register. [For details, see PCI
Express Base Specification, Rev. 2.0.]
Implement a driver for the PCIe PME root port service working in
accordance with the above description.
Based on a patch from Shaohua Li <shaohua.li@intel.com>.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add function pci_check_pme_status() that will check the PME status
bit of given device and clear it along with the PME enable bit. It
will be necessary for PCI run-time power management.
Based on a patch from Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Make pci_bridge_check_ranges() store the PCI_PREF_RANGE_TYPE_64 in
addition to IORESOURCE_MEM_64. Just like pci_read_bridge_bases().
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Handle the case where the slot bridge that doesn't get a pre-allocated
resource big enough to handle its child resources.. For example pcie
devices need 256M, but the bridge only gets 2M preallocated.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move bus_size_bridges and assign resources out of pciehp_add_bridge()
and do them all together, one time, including slot bridge, to avoid to
calling assign resources several times when there are several bridges
under the slot bridge. Using pci_assign_unassigned_bridge_resources.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For use by pciehp.
pci_setup_bridge() will not check enabled for the slot bridge, otherwise
update res is not updated to bridge BAR. That is, bridge is already
enabled for port service.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
BIOS separates IO ranges between several IOHs, and on some slots, BIOS assigns
resources to a bridge, but stops assigning resources to the device under that
bridge, because the device needs a big resource.
So:
1. allocate resources and record the failed device resources
2. clear the BIOS assigned resources of the parent bridge of failing device
3. go back and call pci assign unassigned
4. if it still fails, go up the tree, clear more bridges. and try again
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When clearing leaf bridge resources, trying to get a big enough one, we
could shrink the bridge if there is no resource under it. Confirm
against the old resource side to make sure we're increasing the
allocation.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We already track unassigned resources in struct resource, and this
prevents us from overwriting resource flags and info in the unassigned
case.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This allows us to track failed allocations for later re-trying with
reallocation.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We use this in later patches to free resrouce ranges for reassignment in
an effort to support a wider variety of PCI topologies.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add header file to fix build error:
drivers/pci/hotplug/ibmphp_hpc.c:135: error: implicit declaration of function 'init_MUTEX'
drivers/pci/hotplug/ibmphp_hpc.c:136: error: implicit declaration of function 'init_MUTEX_LOCKED'
drivers/pci/hotplug/ibmphp_hpc.c:797: error: implicit declaration of function 'down'
drivers/pci/hotplug/ibmphp_hpc.c:807: error: implicit declaration of function 'up'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Yinghai pointed out that the new pci_scan_slot() crashes when called
on an ARI-capable slot that is empty. Fix this by exiting early from
pci_scan_slot if there is no device in the slot.
Also make next_ari_func() robust against devices not existing in case
the ARI capability is corrupt. ARI also requires that the devices be
listed in order, so if we find a function listed that is out of order,
stop scanning to prevent loops.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stanse found an ommitted pci_dev_put on one error path in
cpcihp_generic_init. The path is taken on !dev, but also when
dev->hdr_type != PCI_HEADER_TYPE_BRIDGE. However it omits to
pci_dev_put on the latter.
As it is fine to pass NULL to pci_dev_put, put it in there
uncoditionally.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Scott Murray <scott@spiteful.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The ISDN4Linux HiSax driver family contains the last remaining users
of the deprecated pci_find_device() function. This patch creates a
private copy of that function in HiSax, and removes the now unused
global function together with its controlling configuration option,
CONFIG_PCI_LEGACY.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Don't print out resources without flags to avoid cluttering up the debug
output.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is a good cleanup in itself, and makes it easier to modify specific
resource types in later code.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ibmphp driver currently maps only 1KB of ebda memory area into kernel address
space during driver initialization. This causes kernel oops when the driver is
modprobe'd and it accesses memory beyond 1KB within ebda segment. The first
byte of ebda segment actually stores the length of the ebda region in
Kilobytes. Hence make use of the length parameter and map the entire ebda
region.
Signed-off-by: Chandru Siddalingappa <chandru@linux.vnet.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stanse found a cut&pasted memory leak in pciehp_queue_pushbutton_work
and shpchp_queue_pushbutton_work. info is not freed/assigned on all
paths. Fix that.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently, drivers/pci/quirks.c is built unconditionally, but if
CONFIG_PCI_QUIRKS is unset, the only things actually built in this
file are definitions of global variables and empty functions (due to
the #ifdef CONFIG_PCI_QUIRKS embracing all of the code inside the
file). This is not particularly nice and if someone overlooks
the #ifdef CONFIG_PCI_QUIRKS, build errors are introduced.
To clean that up, move the definitions of the global variables in
quirks.c that are always built to pci.c, move the definitions of
the empty functions (compiled when CONFIG_PCI_QUIRKS is unset) to
headers (additionally make these functions static inline) and modify
drivers/pci/Makefile so that quirks.c is only built if
CONFIG_PCI_QUIRKS is set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No longer needed and causes build breakage.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Take advantage of some gaps in the table to fit in support for AGP speeds.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Both PCIe and PCI-X bridges report their secondary bus speed in their
respective capabilities.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move the max_bus_speed and cur_bus_speed into the pci_bus. Expose the
values through the PCI slot driver instead of the hotplug slot driver.
Update all the hotplug drivers to use the pci_bus instead of their own
data structures.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These enums must not overlap anyway, since we only have a single
pci_bus_speed_strings array. Use a single enum, and move it to
pci.h. Add 'SPEED' to the pcie names to make it clear what they are.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The Alternate Routing-ID Interpretation capability allows a single device
to have up to 256 functions. They can be populated sparsely, so the
current technique of scanning every eighth function is not guaranteed
to find them all. By introducing a 'next_fn' function pointer, we can
use the linked list of functions in the ARI capability to scan all the
functions which exist.
We can then speed up the pci_scan_slot by skipping the scan of subsequent
devfns for PCIe devices which are the direct children of Root Ports or
Downstream Ports. These devices are only permitted to implement device
0, unless they are ARI devices, in which case they'll be scanned by the
ARI code above.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds support for the 82576NS Serdes adapter to the existing pci
quirk for 82576 parts.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For use by code that needs to walk extended capability lists before
pci_dev structures are set up.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <43F901BD926A4E43B106BF17856F07559FB80CFD@orsmsx508.amr.corp.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add and export pci_num_vf to allow other subsystems to determine how many
virtual function devices are associated with an SR-IOV physical function
device.
Add macros dev_is_pci, dev_is_ps, and dev_num_vf to make it easier for
non-PCI specific code to determine SR-IOV capabilities.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename add_range() to add_bus_range() to avoid conflict with the
naming of the generic range manipulation functions.
LKML-Reference: <1265793639-15071-4-git-send-email-yinghai@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Update pci_set_vga_state to call arch dependent functions to enable Legacy
VGA I/O transactions to be redirected to correct target.
[akpm@linux-foundation.org: make pci_register_set_vga_state() __init]
Signed-off-by: Mike Travis <travis@sgi.com>
LKML-Reference: <201002022238.o12McE1J018723@imap1.linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The new cs5535-* drivers use PCI header config info rather than MSRs to
determine the memory region to use for things like GPIOs and MFGPTs. As
anticipated, we've run into a buggy BIOS:
[ 0.081818] pci 0000:00:14.0: reg 10: [io 0x6000-0x7fff]
[ 0.081906] pci 0000:00:14.0: reg 14: [io 0x6100-0x61ff]
[ 0.082015] pci 0000:00:14.0: reg 18: [io 0x6200-0x63ff]
[ 0.082917] pci 0000:00:14.2: reg 20: [io 0xe000-0xe00f]
[ 0.083551] pci 0000:00:15.0: reg 10: [mem 0xa0010000-0xa0010fff]
[ 0.084436] pci 0000:00:15.1: reg 10: [mem 0xa0011000-0xa0011fff]
[ 0.088816] PCI: pci_cache_line_size set to 32 bytes
[ 0.088938] pci 0000:00:14.0: address space collision: [io 0x6100-0x61ff] already in use
[ 0.089052] pci 0000:00:14.0: can't reserve [io 0x6100-0x61ff]
This is a Soekris board, and its BIOS sets the size of the PCI ISA bridge
device's BAR0 to 8k. In reality, it should be 8 bytes (BAR0 is used for
SMBus stuff). This quirk checks for an incorrect size, and resets it
accordingly.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Tested-by: Leigh Porter <leigh@leighporter.org>
Tested-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Callers (acpi_memhotplug.c, dock.c and others) check for the return
value of acpi_bus_add() and assume a valid device was returned in
case zero was returned.
Thus return -ENODEV if no device was found in acpi_bus_scan and
propagate this through acpi_bus_add and acpi_bus_start.
Also remove a confusing comment in acpiphp_glue.c, acpi_bus_scan
will and cannot invoke if acpi_bus_add returns no valid device.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We are missing these when building the pci_dev from scratch off
the Open Firmware device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
acpi_integer is now obsolete and removed from the ACPICA code base,
replaced by u64.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The aer_inject module hangs in aer_inject() when checking the device's
error masks. The hang is due to a recursive use of the aer_inject lock.
The aer_inject() routine grabs the lock while processing the error and then
calls pci_read_config_dword to read the masks. The pci_read_config_dword
routine is earlier overridden by pci_read_aer, which among other things,
grabs the aer_inject lock.
Fixed by moving the pci_read_config_dword calls to read the masks to before
the lock is taken.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The Correcteable/Uncorrectable Error Mask Registers are used by PCIe AER
driver which will controls the reporting of individual errors to PCIe RC
via PCIe error messages.
If hardware masks special error reporting to RC, the aer_inject driver
should not inject aer error.
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Youquan, Song <youquan.song@intel.com>
Acked-by: Ying, Huang <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It turns out that some PCI devices require extra delays when changing
power state from D3 to D0 (and the other way around). Although this
is against the PCI specification, we can handle it quite easily by
allowing drivers to define arbitrary D3 delays for devices known to
require extra time for switching power states.
Introduce additional field d3_delay in struct pci_dev and use it to
store the value of the device's D0->D3 delay, in miliseconds. Make
the PCI PM core code use the per-device d3_delay unless
pci_pm_d3_delay is greater (in which case the latter is used).
[This also allows the driver to specify d3_delay shorter than the
10 ms required by the PCI standard if the device is known to be able
to handle that.]
Make the sky2 driver set d3_delay to 150 for devices handled by it.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=14730 which is a
listed regression from 2.6.30.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit e0cd516 "PCI: derive nearby CPUs from device's instead of bus'
NUMA information" causes an null pointer dereference when reading from
the sysfs attributes local_cpu* on Intel machines with no ACPI NUMA
proximity info, since dev->numa_node gets set to -1 for all PCI devices,
which then gets passed to cpumask_of_node.
Add a check to prevent this.
Signed-off-by: David John <davidjon@xenontk.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduced by commit 5b889bf23 ("PCI: Fix build if quirks are not
enabled"), which made the pci_dev_reset_methods[] array static and
'const', but didn't then change the code to match, and use a const
pointer when moving it to quirks.c.
Trivially fixed by just adding the required 'const' to the iterator
variable.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit b9c3b26641 ("PCI: support
device-specific reset methods") the kernel build is broken if
CONFIG_PCI_QUIRKS is unset.
Fix this by moving pci_dev_specific_reset() to drivers/pci/quirks.c and
providing an empty replacement for !CONFIG_PCI_QUIRKS builds.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dmar_tbl is declared as __initdata, but dmar_ir_support() is not declared
as an __init function. Fix is simple since the only caller of dmar_ir_support
(intr_remapping_supported) is an __init function.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/cardbus: Add a fixup hook and fix powerpc
PCI: change PCI nomenclature in drivers/pci/ (non-comment changes)
PCI: change PCI nomenclature in drivers/pci/ (comment changes)
PCI: fix section mismatch on update_res()
PCI: add Intel 82599 Virtual Function specific reset method
PCI: add Intel USB specific reset method
PCI: support device-specific reset methods
PCI: Handle case when no pci device can provide cache line size hint
PCI/PM: Propagate wake-up enable for PCIe devices too
vgaarbiter: fix a typo in the vgaarbiter Documentation
The cardbus code creates PCI devices without ever going through the
necessary fixup bits and pieces that normal PCI devices go through.
There's in fact a commented out call to pcibios_fixup_bus() in there,
it's commented because ... it doesn't work.
I could make pcibios_fixup_bus() do the right thing on powerpc easily
but I felt it cleaner instead to provide a specific hook pci_fixup_cardbus
for which a weak empty implementation is provided by the PCI core.
This fixes cardbus on powerbooks and probably all other PowerPC
platforms which was broken completely for ever on some platforms and
since 2.6.31 on others such as PowerBooks when we made the DMA ops
mandatory (since those are setup by the fixups).
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Changing occurrences of variants of PCI-X and PCIe to the PCI-SIG
terms listed in the "Trademark and Logo Usage Guidelines".
http://www.pcisig.com/developers/procedures/logos/Trademark_and_Logo_Usage_Guidelines_updated_112206.pdf
Patch is limited to drivers/pci/ and changes concern non-comment parts or
anything that might be visible to the user.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Handle device specific timeout and use FLR.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Dexuan Cui <dexuan.cui@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add a new type of quirk for resetting devices at pci_dev_reset time.
This is necessary to handle device with nonstandard reset procedures,
especially useful for guest drivers.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Dexuan Cui <dexuan.cui@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Prior to this patch, if pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, ...)
returns 0 for all dev, pci_cache_line_size ends up set to zero
(instead of pci_dfl_cache_line_size).
This patch ensures the pci_cache_line_size = pci_dfl_cache_line_size
setting in the above scenario.
This happens in case of a kvm-88 guest (where, consequently, the rtl8139
NIC failed to initialize).
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Csaba Henk <csaba@gluster.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Having read the PM part of the PCIe 2.0 specification more carefully
I think that it was a mistake to restrict the wake-up enable
propagation to non-PCIe devices, because if we do not request
control of the root ports' PME registers via OSC, PCIe PME is
supposed to be handled by the platform, just like the non-PCIe PME.
Even if we do that, the wake-up propagation is done to allow the
devices to wake up the system from sleep states which involves the
platform anyway, so it won't hurt.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* git://git.infradead.org/iommu-2.6:
implement early_io{re,un}map for ia64
Revert "Intel IOMMU: Avoid memory allocation failures in dma map api calls"
intel-iommu: ignore page table validation in pass through mode
intel-iommu: Fix oops with intel_iommu=igfx_off
intel-iommu: Check for an RMRR which ends before it starts.
intel-iommu: Apply BIOS sanity checks for interrupt remapping too.
intel-iommu: Detect DMAR in hyperspace at probe time.
dmar: Fix build failure without NUMA, warn on bogus RHSA tables and don't abort
iommu: Allocate dma-remapping structures using numa locality info
intr_remap: Allocate intr-remapping table using numa locality info
dmar: Allocate queued invalidation structure using numa locality info
dmar: support for parsing Remapping Hardware Static Affinity structure
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPICA: Update version to 20091112.
ACPICA: Add additional module-level code support
ACPICA: Deploy new create integer interface where appropriate
ACPICA: New internal utility function to create Integer objects
ACPICA: Add repair for predefined methods that must return sorted lists
ACPICA: Fix possible fault if return Package objects contain NULL elements
ACPICA: Add post-order callback to acpi_walk_namespace
ACPICA: Change package length error message to an info message
ACPICA: Reduce severity of predefined repair messages, Warning to Info
ACPICA: Update version to 20091013
ACPICA: Fix possible memory leak for Scope ASL operator
ACPICA: Remove possibility of executing _REG methods twice
ACPICA: Add repair for bad _MAT buffers
ACPICA: Add repair for bad _BIF/_BIX packages
* 'timers-for-linus-hpet' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: hpet: Make WARN_ON understandable
x86: arch specific support for remapping HPET MSIs
intr-remap: generic support for remapping HPET MSIs
x86, hpet: Simplify the HPET code
x86, hpet: Disable per-cpu hpet timer if ARAT is supported
commit eb3fa7cb51 said Intel IOMMU
Intel IOMMU driver needs memory during DMA map calls to setup its
internal page tables and for other data structures. As we all know
that these DMA map calls are mostly called in the interrupt context
or with the spinlock held by the upper level drivers(network/storage
drivers), so in order to avoid any memory allocation failure due to
low memory issues, this patch makes memory allocation by temporarily
setting PF_MEMALLOC flags for the current task before making memory
allocation calls.
We evaluated mempools as a backup when kmem_cache_alloc() fails
and found that mempools are really not useful here because
1) We don't know for sure how much to reserve in advance
2) And mempools are not useful for GFP_ATOMIC case (as we call
memory alloc functions with GFP_ATOMIC)
(akpm: point 2 is wrong...)
The above description doesn't justify to waste system emergency memory
at all. Non MM subsystem must not use PF_MEMALLOC. Memory reclaim need
few memory, anyone must not prevent it. Otherwise the system cause
mysterious hang-up and/or OOM Killer invokation.
Plus, akpm already pointed out what we should do.
Then, this patch revert it.
Cc: Keshavamurthy Anil S <anil.s.keshavamurthy@intel.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We are seeing a bug when booting w/ iommu=pt with current upstream
(bisect blames 19943b0e30 "intel-iommu:
Unify hardware and software passthrough support).
The issue is specific to this loop during identity map initialization
of each device:
domain_context_mapping_one(si_domain, ..., CONTEXT_TT_PASS_THROUGH)
...
/* Skip top levels of page tables for
* iommu which has less agaw than default.
*/
for (agaw = domain->agaw; agaw != iommu->agaw; agaw--) {
pgd = phys_to_virt(dma_pte_addr(pgd));
if (!dma_pte_present(pgd)) { <------ failing here
spin_unlock_irqrestore(&iommu->lock, flags);
return -ENOMEM;
}
This box has 2 iommu's in it. The catchall iommu has MGAW == 48, and
SAGAW == 4. The other iommu has MGAW == 39, SAGAW == 2.
The device that's failing the above pgd test is the only device connected
to the non-catchall iommu, which has a smaller address width than the
domain default. This test is not necessary since the context is in PT
mode and the ASR is ignored.
Thanks to Don Dutile for discovering and debugging this one.
Cc: stable@kernel.org
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The hotplug notifier will call find_domain() to see if the device in
question has been assigned an IOMMU domain. However, this should never
be called for devices with a "dummy" domain, such as graphics devices
when intel_iommu=igfx_off is set and the corresponding IOMMU isn't even
initialised. If you do that, it'll oops as it dereferences the (-1)
pointer.
The notifier function should check iommu_no_mapping() for the
device before doing anything else.
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some HP BIOSes report an RMRR region (a region which needs a 1:1 mapping
in the IOMMU for a given device) which has an end address lower than its
start address. Detect that and warn, rather than triggering the
BUG() in dma_pte_clear_range().
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The BIOS errors where an IOMMU is reported either at zero or a bogus
address are causing problems even when the IOMMU is disabled -- because
interrupt remapping uses the same hardware. Ensure that the checks get
applied for the interrupt remapping initialisation too.
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Many BIOSes will lie to us about the existence of an IOMMU, and claim
that there is one at an address which actually returns all 0xFF.
We need to detect this early, so that we know we don't have a viable
IOMMU and can set up swiotlb before it's too late.
Cc: stable@kernel.org
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
x86, Calgary IOMMU quirk: Find nearest matching Calgary while walking up the PCI tree
x86/amd-iommu: Remove amd_iommu_pd_table
x86/amd-iommu: Move reset_iommu_command_buffer out of locked code
x86/amd-iommu: Cleanup DTE flushing code
x86/amd-iommu: Introduce iommu_flush_device() function
x86/amd-iommu: Cleanup attach/detach_device code
x86/amd-iommu: Keep devices per domain in a list
x86/amd-iommu: Add device bind reference counting
x86/amd-iommu: Use dev->arch->iommu to store iommu related information
x86/amd-iommu: Remove support for domain sharing
x86/amd-iommu: Rearrange dma_ops related functions
x86/amd-iommu: Move some pte allocation functions in the right section
x86/amd-iommu: Remove iommu parameter from dma_ops_domain_alloc
x86/amd-iommu: Use get_device_id and check_device where appropriate
x86/amd-iommu: Move find_protection_domain to helper functions
x86/amd-iommu: Simplify get_device_resources()
x86/amd-iommu: Let domain_for_device handle aliases
x86/amd-iommu: Remove iommu specific handling from dma_ops path
x86/amd-iommu: Remove iommu parameter from __(un)map_single
x86/amd-iommu: Make alloc_new_range aware of multiple IOMMUs
...
Remove a stray space in pci_save_state().
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit ae21ee65e8 "PCI: acs p2p upsteram
forwarding enabling" doesn't actually enable ACS.
Add a function to pci core to allow an IOMMU to request that ACS
be enabled. The existing mechanism of using iommu_found() in the pci
core to know when ACS should be enabled doesn't actually work due to
initialization order; iommu has only been detected not initialized.
Have Intel and AMD IOMMUs request ACS, and Xen does as well during early
init of dom0.
Cc: Allen Kay <allen.m.kay@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This problem happened when removing PCIe root port using PCI logical
hotplug operation.
The immediate cause of this problem is that the pointer to invalid
data structure is passed to pcie_update_aspm_capable() by
pcie_aspm_exit_link_state(). When pcie_aspm_exit_link_state() received
a pointer to root port link, it unconfigures the root port link and
frees its data structure at first. At this point, there are not links
to configure under the root port and the data structure for root port
link is already freed. So pcie_aspm_exit_link_state() must not call
pcie_update_aspm_capable() and pcie_config_aspm_path().
This patch fixes the problem by changing pcie_aspm_exit_link_state()
not to call pcie_update_aspm_capable() and pcie_config_aspm_path() if
the specified link is root port link.
------------[ cut here ]------------
kernel BUG at drivers/pci/pcie/aspm.c:606!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
last sysfs file: /sys/devices/pci0000:40/0000:40:13.0/remove
CPU 1
Modules linked in: shpchp
Pid: 9345, comm: sysfsd Not tainted 2.6.32-rc5 #98 ProLiant DL785 G6
RIP: 0010:[<ffffffff811df69b>] [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP: 0018:ffff88082a2f5ca0 EFLAGS: 00010202
RAX: 0000000000000e77 RBX: ffff88182cc3e000 RCX: ffff88082a33d006
RDX: 0000000000000001 RSI: ffffffff811dff4a RDI: ffff88182cc3e000
RBP: ffff88082a2f5cc0 R08: ffff88182cc3e000 R09: 0000000000000000
R10: ffff88182fc00180 R11: ffff88182fc00198 R12: ffff88182cc3e000
R13: 0000000000000000 R14: ffff88182cc3e000 R15: ffff88082a2f5e20
FS: 00007f259a64b6f0(0000) GS:ffff880864600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00007feb53f73da0 CR3: 000000102cc94000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process sysfsd (pid: 9345, threadinfo ffff88082a2f4000, task ffff88082a33cf00)
Stack:
ffff88182cc3e000 ffff88182cc3e000 0000000000000000 ffff88082a33cf00
<0> ffff88082a2f5cf0 ffffffff811dff52 ffff88082a2f5cf0 ffff88082c525168
<0> ffff88402c9fd2f8 ffff88402c9fd2f8 ffff88082a2f5d20 ffffffff811d7db2
Call Trace:
[<ffffffff811dff52>] pcie_aspm_exit_link_state+0xf5/0x11e
[<ffffffff811d7db2>] pci_stop_bus_device+0x76/0x7e
[<ffffffff811d7d67>] pci_stop_bus_device+0x2b/0x7e
[<ffffffff811d7e4f>] pci_remove_bus_device+0x15/0xb9
[<ffffffff811dcb8c>] remove_callback+0x29/0x3a
[<ffffffff81135aeb>] sysfs_schedule_callback_work+0x15/0x6d
[<ffffffff81072790>] worker_thread+0x19d/0x298
[<ffffffff8107273b>] ? worker_thread+0x148/0x298
[<ffffffff81135ad6>] ? sysfs_schedule_callback_work+0x0/0x6d
[<ffffffff810765c0>] ? autoremove_wake_function+0x0/0x38
[<ffffffff810725f3>] ? worker_thread+0x0/0x298
[<ffffffff8107629e>] kthread+0x7d/0x85
[<ffffffff8102eafa>] child_rip+0xa/0x20
[<ffffffff8102e4bc>] ? restore_args+0x0/0x30
[<ffffffff81076221>] ? kthread+0x0/0x85
[<ffffffff8102eaf0>] ? child_rip+0x0/0x20
Code: 89 e5 8a 50 48 31 c0 c0 ea 03 83 e2 07 e8 b2 de fe ff c9 48 98 c3 55 48 89 e5 41 56 49 89 fe 41 55 41 54 53 48 83 7f 10 00 74 04 <0f> 0b eb fe 48 8b 05 da 7d 63 00 4c 8d 60 e8 4c 89 e1 eb 24 4c
RIP [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP <ffff88082a2f5ca0>
---[ end trace 6ae0f65bdeab8555 ]---
Reported-by: Alex Chiang <achiang@hp.com>
Tested-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pci_cleanup_aer_correct_error_status() function has been
#if 0'd out since 2.6.25. Time to remove the dead code.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The current implementation of pci_cleanup_aer_uncorrect_error_status
only clears either fatal or non-fatal error status bits depending
on the state of the I/O channel. This implementation will then often
leave some bits set after PCI error recovery completes. The uncleared bit
settings will then be falsely reported the next time an AER interrupt is
generated for that hierarchy. An easy way to illustrate this issue is to
use the aer-inject module to simultaneously inject both an uncorrectable
non-fatal and uncorrectable fatal error. One of the errors will not be
cleared.
This patch resolves this issue by unconditionally clearing all bits in
the AER uncorrectable status register. All settings and corrective action
strategies are saved and determined before
pci_cleanup_aer_uncorrect_error_status is called, so this change should not
affect errory handling functionality.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove 'port_type' field in struct pcie_port_data(), because we can
get port type information from struct pci_dev. With this change, this
patch also does followings:
- Remove struct pcie_port_data because it no longer has any field.
- Remove portdrv private definitions about port type (PCIE_RC_PORT,
PCIE_SW_UPSTREAM_PORT and PCIE_SW_DOWNSTREAM_PORT), and use generic
definitions instead.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add missing service irqs cleanup in the error code path of
pcie_port_device_register().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Call pci_enable_device() before initializing service irqs, because
legacy interrupt is initialized in pci_enable_device() on some
architectures.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch cleans up the service irqs initialization as follows:
- Remove 'irq_mode' field in pcie_port_data and related definitions,
which is not needed because we can get the same information from
'is_msix', 'is_msi' and 'pin' fields in struct pci_dev.
- Change the name of 'vectors' argument of assign_interrupt_mode() to
'irqs' because it holds irq numbers actually. People might confuse
it with CPU vector or MSI/MSI-X vector.
- Change function name assign_interrupt_mode() to init_service_irqs()
becasuse we no longer have 'irq_mode' data structure, and new name
is more straightforward (IMO).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No reason to check PME capability outside get_port_device_capability().
Do it in get_port_device_capability().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
